2.4 GHz Class-E power amplifier with transmissionline harmonic terminations

The design procedure, fabrication and measurement of a Class-E power amplifier with excellent second- and third-harmonic suppression levels are presented. A simplified design technique offering compact physical layout is proposed. With a 1.2 mm gate-width GaAs MESFET as a switching device, the amplifier is capable of delivering 19.2 dBm output power at 2.41 GHz, achieves peak PAE of 60% and drain efficiency of 69%, and exhibits 9 dB power gain when operated from a 3 V DC supply voltage. When compared to the classical Class-E two-harmonic termination amplifier, the Class-E amplifier employing three-harmonic terminations has more than 10% higher drain efficiency and 23 dB better third-harmonic suppression level. Experimental results are presented and good agreement with simulation is obtained. Further, to verify the practical implementation in communication systems, the Bluetooth-standard GFSK modulated signal is applied to both two- and three-harmonic amplifiers. The measured RMS FSK deviation error and RMS magnitude error were, for the three-harmonic case, 1.01 kHz and 0.122%, respectively, and, for the two-harmonic case, 1.09 kHz and 0.133%. © 2007 The Institution of Engineering and Technology.

Sensitivity characteristics of inverse Class-E power amplifier

In this paper, an analysis is performed in order to determine the effects that variations in circuit component values, frequency, and duty cycle have on the performance of the newly introduced inverse Class-E amplifier. Analysis of the inverse Class-E amplifier under the generalized condition of arbitrary duty cycle is performed and it is shown that the inverse Class-E amplifier is reasonably tolerant to circuit parameter variations. When compared to the conventional Class-E amplifier the inverse Class-E amplifier offers the potential for high efficiency at increased output power as well as higher peak output power levels than are available with a conventional Class-E amplifier. Further the inverse Class-E amplifier provides more flexibility for deployment with a pulsewidth modulator as the means of producing full-carrier amplitude modulation (AM) due to its ability to operate to high AM modulation indices.

Transmission line matching effects on the performance of shunt-C/series-tuned and series-L/parallel-tuned Class-E amplifiers

The impact that the transmission-line load-network has on the performance of the recently introduced series-L/parallel-tuned Class-E amplifier and the classic shunt-C/series-tuned configuration when compared to optimally derived lumped load networks is discussed. In addition an improved load topology which facilitates harmonic suppression of up to 5 order as required for maximum Class-E efficiency as well as load resistance transformation and a design procedure involving the use of Kuroda's identity and Richard's transformation enable a distributed synthesis process which dispenses with the need for iterative tuning as previously required in order to achieve optimum Class-E operation. © 2005 IEEE.

Analysis of the effect of finite d.c. blocking capacitance and finite d.c. feed inductance on the performance of inverse class-E amplifiers

The first analysis and synthesis equations for the newly introduced inverse Class-E amplifier when operated with a finite d.c. blocking capacitance and a finite d.c.-feed inductance are presented in the paper. Closed-form design equations are derived in order to establish the circuit component values required for optimum synthesis. Excellent agreement between numerical simulation results and theoretical prediction is obtained. It is shown that drain efficiency approaching 100 at a pre-specified output power level can be achieved as zero-current switching and zero-current derivative conditions are simultaneously satisfied. The proposed analysis offers the prospect for realistic MMIC implementation.

Credit and community: working class debt in the UK since 1880

This book examines credit in working class communities since 1880, focusing on forms of borrowing that were dependent on personal relationships and social networks. It provides an extended historical discussion of credit unions, legal and illegal moneylenders (loan sharks), and looks at the concept of ‘financial exclusion’. Initially, the book focuses on the history of tallymen, check traders, and their eventual movement into moneylending following the loss of their more affluent customers, due to increased spending power and an increasingly liberalized credit market. They also faced growing competition from mail order companies operating through networks of female agents, whose success owed much to the reciprocal cultural and economic conventions that lay at the heart of traditional working class credit relationships. Discussion of these forms of credit is related to theoretical debates about cultural aspects of credit exchange that ensured the continuing success of such forms of lending, despite persistent controversies about their use. The book contrasts commercial forms of credit with formal and informal co-operative alternatives, such as the mutuality clubs operated by co-operative retailers and credit unions. It charts the impact of post-war immigration upon credit patterns, particularly in relation to the migrant (Irish and Caribbean) origins of many credit unions and explains the relative lack of success of the credit union movement. The book contributes to anti-debt debates by exploring the historical difficulties of developing legislation in relation to the millions of borrowers who have patronized what has come to be termed the sub-prime sector.

Power combining techniques into unbalanced loads for Class-E and inverse Class-E amplifiers

A power combining strategy for Class-E and inverse Class-E amplifiers operating at high frequencies such that they can operate into unbalanced loads is proposed. This power combining method is particularly important for the inverse Class-E amplifier configuration whose single-stage topology is naturally limited for small-to-medium power applications. Design examples for the power combining synthesis of classical Class-E and then inverse Class-E amplifiers with specification 3 V-1.5 W-2.5 GHz are given. For this specification, it is shown that a three-branch combiner has a natural 50 V output impedance. The resulting circuits are simulated within Agilent Advanced Design Systems environment with good agreement to theoretical prediction. Further the performance of the proposed circuits when operated in a Linear amplification using Nonlinear Components transmitter configuration whereby two-branch amplifiers are driven with constant amplitude conjugate input phase signals is investigated.

Series-L/parallel-tuned comparison with shunt-C/series-tuned class-E power amplifier

An analysis of the operation of a series-L/parallel-tuned class-E amplifier and its equivalence to the classic shunt-C/series-tuned class-E amplifier are presented. The first reported closed form design equations for the series-L/parallel-tuned topology operating under ideal switching conditions are given. Furthermore, a design procedure is introduced that allows the effect that nonzero switch resistance has on amplifier performance efficiency to be accounted for. The technique developed allows optimal circuit components to be found for a given device series resistance. For a relatively high value of switching device ON series resistance of 4O, drain efficiency of around 66% for the series-L/parallel-tuned topology, and 73% for the shunt-C/series-tuned topology appear to be the theoretical limits. At lower switching device series resistance levels, the efficiency performance of each type are similar, but the series-L/parallel-tuned topology offers some advantages in terms of its potential for MMIC realisation. Theoretical analysis is confirmed by numerical simulation for a 500mW (27dBm), 10% bandwidth, 5 V series-L/parallel-tuned, then, shunt-C/series-tuned class E power amplifier, operating at 2.5 GHz, and excellent agreement between theory and simulation results is achieved. The theoretical work presented in the paper should facilitate the design of high-efficiency switched amplifiers at frequencies commensurate with the needs of modern mobile wireless applications in the microwave frequency range, where intrinsically low-output-capacitance MMIC switching devices such as pHEMTs are to be used.

Peptide DV-28 amide: Prototype of a novel class of bradykinin receptor antagonist isolated from the defensive skin secretion of bombinid toads

Kinestatin, isolated from the skin of the Chinese toad, Bombina maxima, was the first bradykinin B2 receptor antagonist identified in amphibians. Molecular cloning established that it is co-encoded with the bradykinin-related peptide, maximakinin, within one of several skin kininogens. To examine other species within the genus Bombina for the presence of structural homologues of kinestatin, we subjected skin secretion of the toad, Bombina orientalis, to HPLC fractionation with subsequent bioassay of fractions for antagonism of bradykinin activity using an isolated rat tail artery smooth muscle preparation. A single fraction was located that inhibited bradykinin-induced relaxation of rat arterial smooth muscle and MALDI-TOF analysis of this fraction revealed that it contained a single peptide of molecular mass 3198.5 Da. Further primary structural analysis of this peptide showed that it was a 28-mer with an N-terminal Asp (D) residue and a C-terminal Val (V) residue that was amidated. The peptide was named DV-28 amide in accordance with these primary structural attributes. Synthetic DV-28 amide replicated the observed bradykinin antagonistic effect within the smooth muscle bioassay in a dose-dependent manner. In addition, it was observed to inhibit the proliferation of human microvessel endothelial cells (HMECs) as assessed by MTT assay. Bioinformatic analysis revealed that DV-28 amide was, like kinestatin, co-encoded with a bradykinin receptor agonist on one of two skin kininogens identified in B. orientalis. DV-28 amide thus represents a novel class of bradykinin antagonist from skin secretions of bombinid toads that appear to be a rich source of such novel peptides.

Digital Baseband Predistortion Based Linearized Broadband Inverse Class-E Power Amplifier

A newly introduced inverse class-E power amplifier (PA) was designed, simulated, fabricated, and characterized. The PA operated at 2.26 GHz and delivered 20.4-dBm output power with peak drain efficiency (DE) of 65% and power gain of 12 dB. Broadband performance was achieved across a 300-Mitz bandwidth with DE of better than 50% and 1-dB output-power flatness. The concept of enhanced injection predistortion with a capability to selectively suppress unwanted sub-frequency components and hence suitable for memory effects minimization is described coupled with a new technique that facilitates an accurate measurement of the phase of the third-order intermodulation (IM3) products. A robust iterative computational algorithm proposed in this paper dispenses with the need for manual tuning of amplitude and phase of the IM3 injected signals as commonly employed in the previous publications. The constructed inverse class-E PA was subjected to a nonconstant envelope 16 quadrature amplitude modulation signal and was linearized using combined lookup table (LUT) and enhanced injection technique from which superior properties from each technique can be simultaneously adopted. The proposed method resulted in 0.7% measured error vector magnitude (in rms) and 34-dB adjacent channel leakage power ratio improvement, which was 10 dB better than that achieved using the LUT predistortion alone.

Hybridization of a class of "second order" models of traffic flow

Despite the simultaneous progress of traffic modelling both on the macroscopic and microscopic front, recent works [E. Bourrel, J.B. Lessort, Mixing micro and macro representation of traffic flow: a hybrid model based on the LWR theory, Transport. Res. Rec. 1852 (2003) 193–200; D. Helbing, M. Treiber, Critical discussion of “synchronized flow”, Coop. Transport. Dyn. 1 (2002) 2.1–2.24; A. Hennecke, M. Treiber, D. Helbing, Macroscopic simulations of open systems and micro–macro link, in: D. Helbing, H.J. Herrmann, M. Schreckenberg, D.E. Wolf (Eds.), Traffic and Granular Flow ’99, Springer, Berlin, 2000, pp. 383–388] highlighted that one of the most promising way to simulate efficiently traffic flow on large road networks is a clever combination of both traffic representations: the hybrid modelling. Our focus in this paper is to propose two hybrid models for which the macroscopic (resp. mesoscopic) part is based on a class of second order model [A. Aw, M. Rascle, Resurection of second order models of traffic flow?, SIAM J. Appl. Math. 60 (2000) 916–938] whereas the microscopic part is a Follow-the Leader type model [D.C. Gazis, R. Herman, R.W. Rothery, Nonlinear follow-the-leader models of traffic flow, Oper. Res. 9 (1961) 545–567; R. Herman, I. Prigogine, Kinetic Theory of Vehicular Traffic, American Elsevier, New York, 1971]. For the first hybrid model, we define precisely the translation of boundary conditions at interfaces and for the second one we explain the synchronization processes. Furthermore, through some numerical simulations we show that the waves propagation is not disturbed and the mass is accurately conserved when passing from one traffic representation to another.