Multiplexed femtomolar quantitation of human cytokines in a fluoropolymer microcapillary film

Sensitive quantitation of multiple cytokines can provide important diagnostic information during infection, inflammation and immunopathology. In this study sensitive immunoassay detection of human cytokines IL-1β, IL-6, IL-12p70 and TNFα is shown for singleplex and multiplex formats using a novel miniaturized ELISA platform. The platform uses a disposable plastic multi-syringe aspirator (MSA) integrating 8 disposable fluoropolymer microfluidic test strips, each containing an array of ten 200 mean i.d. microcapillaries coated with a set of monoclonal antibodies. Each MSA device thus performs 10 tests on 8 samples, delivering 80 measurements. Unprecedented levels of sensitivity were obtained with the novel fluoropolymer microfluidic material and simple colorimetric detection in a flatbed scanner. The limit of detection for singleplex detection ranged from 2.0 to 15.0 pg/ml, i.e. 35 and 713 femtomolar for singleplex cytokine detection, and the intra- and inter-assay coefficient of variation (CV) remained within 10%. In addition, a triplex immunoassay was developed for measuring IL-1β, IL-12p70 and TNFα simultaneously from a given sample in the pg/ml range. These assays permit high sensitivity measurement with rapid <15 min assay or detection from undiluted blood serum. The portability, speed and low-cost of this system are highly suited to point-of-care testing and field diagnostics applications.

Influence of Post and Resin Cement on Stress Distribution of Maxillary Central Incisors Restored with Direct Resin Composite

The current study evaluated the influence of two endodontic post systems and the elastic modulus and film thickness of resin cement on stress distribution in a maxillary central incisor (MCI) restored with direct resin composite using finite element analysis (FEA). A three-dimensional model of an MCI with a coronary fracture and supporting structures was performed. A static chewing pressure of 2.16 N/mm(2) was applied to two areas on the palatal surface of the composite restoration. Zirconia ceramic (ZC) and glass fiber (GF) posts were considered. The stress distribution was analyzed in the post, dentin and cement layer when ZC and GF posts were fixed to the root canals using resin cements of different elastic moduli (7.0 and 18.6 GPa) and different layer thicknesses (70 and 200 mu m). The different post materials presented a significant influence on stress distribution with lesser stress concentration when using the GF post. The higher elastic modulus cement created higher stress levels within itself. The cement thicknesses did not present significant changes.

Effect of surfactants on the functional properties of gelatin-based edible films

The aim of this research was to evaluate the plasticizing effect of natural surfactants lecithin or yucca extract from Yucca schidigera on gelatin-based films Films containing yucca extract showed higher tensile strength values (similar to 90-40 MPa) and moisture contents (similar to 15%) and less elongation (similar to 5%) and water vapor permeability values (similar to 0 22-009 g mm m(-2) h(-1) kPa(-1)) compared to films containing lecithin Soluble films (similar to 20-50%) were obtained when yucca extract was used while lecithin produced low soluble films (<10%) The opacity of the films (similar to 14 5-16 2%) was similar for both surfactants and the film surface morphologies were continuous and homogeneous X-ray diffraction indicated that the addition of surfactants produced amorphous films compared to gelatin-based films and FT-Infrared spectroscopy showed no evidence of association between the surfactants and the gelatin The plasticizing effect was not obtained after surfactants addition and casting technique (C) 2010 Elsevier Ltd All rights reserved

Effect of polyol excess on the electrical property of vegetable-polyurethane film

Freestanding castor oil-based polyurethane (PU) film was obtained using spin-coating method. The effect of polyol content was analysed by means of thermally stimulated depolarisation current and AC dielectric measurements techniques. Two relaxation peaks were observed in the temperature range of -40 to 60 degrees C for PU with different polyol contents. The presence of polyol excess provides a shift to lower temperature of the a relaxation and the decrease in the activation energy of the transition in this region might be attributed to the plasticising effect of the polyol. The peak at higher temperature is due to the Maxwell-Wagner-Sillars relaxation, which also shifts in the low temperature direction as the polyol content is increased.

Anodic oxidation of wastewater containing the Reactive Orange 16 Dye using heavily boron-doped diamond electrodes

Boron-doped diamond (BDD) films grown on the titanium substrate were used to study the electrochemical degradation of Reactive Orange (RO) 16 Dye. The films were produced by hot filament chemical vapor deposition (HFCVD) technique using two different boron concentrations. The growth parameters were controlled to obtain heavily doped diamond films. They were named as E1 and E2 electrodes, with acceptor concentrations of 4.0 and 8.0 x 10(21) atoms cm(-3), respectively. The boron levels were evaluated from Mott-Schottky plots also corroborated by Raman`s spectra, which characterized the film quality as well as its physical property. Scanning Electron Microscopy showed well-defined microcrystalline grain morphologies with crystal orientation mixtures of (1 1 1) and (1 00). The electrode efficiencies were studied from the advanced oxidation process (AOP) to degrade electrochemically the Reactive Orange 16 azo-dye (RO16). The results were analyzed by UV/VIS spectroscopy, total organic carbon (TOC) and high-performance liquid chromatography (HPLC) techniques. From UV/VIS spectra the highest doped electrode (E2) showed the best efficiency for both, the aromaticity reduction and the azo group fracture. These tendencies were confirmed by the TOC and chromatographic measurements. Besides, the results showed a direct relationship among the BDD morphology, physical property, and its performance during the degradation process. (C) 2011 Elsevier B.V. All rights reserved.

Postharvest Storage of 'Ponkan', 'Satsuma Okitusu' and 'Fremont' Tangerines and Their Minimally Processed Products Using Refrigeration and Controlled Atmosphere

This study aimed to evaluate the postharvest conservation of tangerines 'Fremont', 'Satsuma Okitsu' and 'Ponkan' when stored at different conditions, as well as the quality of the minimally processed product. Fruit were harvested when a sugar: acid ratio of 10.0 to 12.0 for 'S. Okitsu' and 'Fremont' and 16.0 to 19.0 for 'Ponkan' was reached, selected for uniformity of color, size, and absence of injuries. Whole fruits were stored at 3 degrees C, 85% RH and 7 degrees C, 95% RH, and after each storage period, fruits were brought to ambient conditions (22 degrees C, 65% RH) for 3 days before evaluation. The minimally processed products (peeled) were packed in polystyrene trays (22.4x14.8x3.7 cm) coated with polyvinyl chloride (PVC) stretchable, with 0.014 mm thickness, and in lidded packages (500 ml) of transparent polyethylene terephthalate. Fruit were analyzed for appearance, weight loss, respiratory rate, package atmosphere, rind and pulp color, soluble solids, titratable acidity and ascorbic acid content. Shelf life of tangerine 'Fremont' was limited to 42 days based on freshness. Its minimally processed product had a 9 day shelf-life for products packaged in PVC film. The mandarins 'S. Okitsu' had 35 days shelf-life at 7 degrees C, which was reduced to 28 days at 3 degrees C. Its fresh-cut product had a shelf-life of 15 days, stored in PVC or PET. 'Ponkan' fruit stored at 3 degrees C had a shelf life of 35 days, which was reduced to 28 days at 7 degrees C. When minimally processed, its shelf-life lasted for 15 days, whether packaged in PVC or PET. The 'Ponkan' had a shelf-life of 35 days at 3 degrees C and 28 days at 7 degrees C, also limited by loss of freshness. When minimally processed and stored in PVC or PET, its shelf life reached 15 days.

Electrochemical investigation of the dimeric oxo-bridged ruthenium complex in aqueous solution and its incorporation within a cation-exchange polymeric film on the electrode surface for electrocatalytic activity of hydrogen peroxide oxidation

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Optical and electrical properties of polymerizing plasmas and their correlation with DLC film properties

Diamond-like carbon (DLC) films were grown from radiofrequency plasmas of acetylene-argon mixtures, at different excitation powers, P. The effects of this parameter on the plasma potential, electron density, electron temperature, and plasma activity were investigated using a Langmuir probe. The mean electron temperature increased from about 0.5 to about 7.0 eV while the mean electron density decreased from about 1.2x10(9) to about 0.2x10(9) cm(-3) as P was increased from 25 to 150 W. Both the plasma potential and the plasma activity were found to increase with increasing P. Through actinometric optical emission spectrometry, the relative concentrations of CH, [CH], and H, [H], in the discharge were mapped as a function of the applied power. A rise in [H] and a fall in [CH] with increasing P were observed and are discussed in relation to the plasma characteristics and the subimplantation model. The optical properties of the films were calculated from ultraviolet-visible spectroscopic data; the surface resistivity was measured by the two-point probe method. The optical gap, E(G), and the surface resistivity, rho(s), fall with increasing P. E(G) and rho(s) are in the ranges of about 2.0-1.3 eV and 10(14)-10(16) Omega/square, respectively. The plasma power also influences the film self-bias, V(b), via a linear dependence, and the effect of V(b) on ion bombardment during growth is addressed together with variation in the relative densities of sp(2) and sp(3) bonds in the films as determined by Raman spectroscopy.

Effect of polyol excess on the electrical property of vegetable-polyurethane film

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Comparison between embossed digital imaging and unprocessed film-based radiography in detecting periodontal bone defects: an in vitro study

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Limiar anaeróbio e velocidade crítica determinada com diferentes distâncias em nadadores de 10 a 15 anos: relações com a performance e a resposta do lactato sanguíneo em testes de endurance

O objetivo deste estudo foi comparar a velocidade crítica (VC) determinada através de diferentes distâncias com o limiar anaeróbio (LAn) e as velocidades máximas mantidas em testes de 20 (V20) e 30 (V30) minutos na natação, verificando se a idade cronológica em jovens nadadores interfere nessas relações. Participaram do estudo 31 nadadores (17 meninas e 14 meninos) divididos segundo a idade cronológica em dois grupos: 10 a 12 anos e 13 a 15 anos. O LAn foi determinado como sendo a velocidade correspondente a 4mM de lactato sanguíneo. A VC1 (25/50/100m), VC2 (100/200/400m) e a VC3 (50/100/200m) foram calculadas através do coeficiente angular da reta de regressão linear entre as distâncias e seus respectivos tempos. As V20 e V30 foram determinadas através de três a seis repetições, com coletas de sangue no 10º minuto e ao final do tiro. Para o grupo de 10 a 12 anos, a VC1 (m/s) (0,98 ± 0,17) e o LAn (0,97 ± 0,12) não foram diferentes entre si, sendo maiores do que a VC2 (0,92 ± 0,16), VC3 (0,89 ± 0,18), V20 (0,92 ± 0,11) e V30 (0,90 ± 0,11). Para o grupo de 13 a 15 anos, a VC1 (m/s)(1,11 ± 0,11) foi maior do que o LAn (1,02 ± 0,07), V20 (0,99 ± 0,09), V30 (0,97 ± 0,09), VC2 (0,98 ± 0,11) e VC3 (1,00 ± 0,11). Pode-se concluir que a distância utilizada na determinação da VC interfere no valor obtido, independente da idade cronológica. A VC determinada com distâncias entre 50 e 400m pode ser utilizada na avaliação da capacidade aeróbia de crianças e adolescentes, substituindo os testes contínuos máximos com durações próximas a 20 ou 30 minutos.

THE USE OF AMPPD AS AN ALTERNATIVE SUBSTRATE FOR AP-MEDIATED DETECTION OF NONRADIOLABELED DNA PROBES IN EUCALYPTUS-SALIGNA

We present a non-radioactive alternative to Southern's (J. Mol. Biol. 98: 503-517, 1975) DNA-DNA hybridization technique. The use of AMPPD - Disodium 3-(4-Methoxyspiro {1,2-dioxetane-3,2'tricyclo[3.3.1.1(3,7)]decan}-4-yl)phyenyl phosphate as an alternative substrate for AP-mediated detection of digoxigenin-11 dUTP-labeled probes made possible the simple and nonhazardous reuse of blots. We used 0.8 % agarose gels containing 30 mug per lane of Eucalyptus saligna DNA, digested with Eco RI, electrophoresed and blotted on to nylon membranes (Hybond-N, Amersham, UK), using the Southern blotting procedure, and UV irradiated for one minute for DNA fixation. The hybridizations were carried out overnight with digoxigenin labeled random inserts of E. saligna DNA by using the Genius Kit (Boehringer Mannheim). Detection of the DNA-DNA hybrids was performed in the presence of 0.5% blocking agent and the substrates NBT/BCIP were replaced by 0.26 mM AMPPD in the final alkaline assay buffer (50 mul/cm2). After membrane incubation for five minutes at room temperature in a sealed plastic bag, the AMPPD solution was retrieved and stored at 4-degrees-C for reuse. A Kodak X-BRAF QA-S film was pressed firmly onto the bag containing the wet membrane, exposed for two to six hours and then developed. After use, the probes were stripped off and the blots reutilized, three times so far, with the same results.

Evaluation of color removal and degradation of a reactive textile azo dye on nanoporous TiO2 thin-film electrodes

The feasibility of the photobleaching of a textile azo dye, reactive orange 16 (C.I. 17757), in aqueous solution using titanium dioxide thin-film electrodes prepared by the sol-gel method was investigated. The best conditions for maximum photoelectrocatalytic degradation were found to be pH > 10 for Na2SO4 medium and pH < 6 for NaCl. In both situations, an applied potential of +1.0 V and low dye concentration are recommended, when 100% of color removal is obtained after 20 min of photoelectrocatalysis. The effects of side reaction pathway on the degradation rate of dye in sulfate and chloride medium were presented and the best performance are optimized to situations closed to that verified in the textile effluent. The influence of variables as applied potential, pH, supporting electrolyte and dye concentration on the kinetics of photoelectrochemical degradation also were investigated. Oxalic acid is identified by HPLC and UV-Vis spectrophotometric methods as the main degradation product generated after 180 min of photoelectrocatalysis of 4 x 10(-5) mol l(-1) dye in sodium sulphate pH 12 and NaCl pH 4.0 and a maximum reduction of 56 and 62% TOC was obtained, respectively. (C) 2004 Elsevier Ltd. All rights reserved.

Label-free DNA detection based on modified conducting polypyrrole films at microelectrodes

A label-free electrochemical detection method for DNA hybridization based on electrostatic modulation of the ion-exchange kinetics of a polypyrrole film deposited at microelectrodes is reported. Synthetic single-stranded 27-mer oligonucleotides (probe) have been immobilized at 2,5-bis(2-thienyl)-N-(3-phosphorylpropyl)pyrrole film formed by electropolymerization on the previously formed polypyrrole layer. The 27- or 18-mer target oligonucleotides were monitored via the electrochemically driven anion exchange of the inner polypyrrole film. The performance of the miniaturized DNA biosensor system was studied in respect to selectivity, sensitivity, reproducibility, and regeneration of the sensor. Control experiments were performed with a noncomplementary target of 27-mer DNA and 12 base-pair mismatched 18-mer sequences, respectively, and did not show any unspecific binding. Under optimized experimental conditions, the label-free electrochemical biosensor enabled the detection limits of 0.16 and 3.5 fmol for the 18- and 2 7-mer DNA strand, respectively. Furthermore, we demonstrate reusability of the electrochemical DNA biosensor after successful recovery of up to 100% of the original signal by regenerating the DNA label-free electrode with 50 mM HCl at room temperature.

Modification of glassy carbon electrodes with a poly-L-lysine/glutaraldehyde film

A film of poly-L-lysine (PLL) adheres better to the surface of a glassy carbon electrode when the PLL is partially cross-linked by means of glutaraldehyde. A film composition of 97.5% PLL/2.5% glutaraldehyde gives good adhesion and retains the anionic exchange capability of the PLL. The performance of the film was tested with hexacyanoferrate(III) using electrochemical and nonelectrochemical accumulation.