Anaerobic Reactor Development for Complex Organic Wastewater

Faculty of Engineering. Cochin University of Science and Technology

Bioremediation of petroleum sludge through Phytoremediation.Land farming and Microbial enhanced oil separation

The objective of this research is to study the feasibility of bioremediating the oily sludge from a refinery site. Three different methods of waste treatment were tried i.e. phytoremediation, land farming and microbial enhanced oil separation in laboratory scale treatment systems. A multiprocess approach by combination of phytoremediation, biostimulation and microbial enhanced oil separation is also presented. The methods of analysis, experimental procedure, and results are incorporated into five chapters of this thesis entitled "Bioremediation of petroleum sludge through phytoremediation, land farming and microbial enhanced oil separation.

Development of bioreactors for nitrifying sewage

Nitrification is the biological oxidation of ammonium, first to nitrite and then to nitrate by two groups of aerobic, chemolithotrophic bacteria belonging to the family Nitrobacteriaceae. The biological nitrification in municipal wastewater treatment is important in those cases were ammonia removal requirement specially exist. In a trickling filter or in an activated sludge system nitrification is rate limiting and thus necessitates longer detention time. The combined carbon oxidation-nitrification processes generally have low population of nitrifiers due to a high ratio of BOD to total nitrogen in the effluent. This necessitates, separate carbon and nitrogen oxidation processes, which thus minimizes wash out ofthe nitrifiers. Therefore, a separate stage nitrification has become essential to achieve faster and efficient removal of ammonia from the wastewater. The present work deals with the development of bio reactor for nitrifying of sewage as the tertiary process so that the treated wastewater can be used for irrigation, algal culture or fish culture

Preparation of useful raw materials from Refinery sludge and its utilisation in rubber processing

Petroleum, a mixture of organic compounds, comes from underground rock formations ranging in age from ten to several hundred million years. The process by which it is formed and developed is not yet completely known. Studies indicate that petroleum is formed mainly from microscopic-sized marine animals and plants. When these organisms died in water of low oxygen content, they did not decompose. Thus their remains sank to the bottom to be buried under accumulations of sediment. Their conversion to petroleum remains a subject of research even today.

Microbial Treatment Of Rubber Latex Centrifugation Effluent

Many of the existing methods for the treatment of rubber latex centrifugation eflluent are not only unsatisfactory in their efliciency to effect near perfect treatment in bringing down the COD to optimum level, but also time consuming and need a large landspace. As the rate of effluent generation is extremely high (20 litres for kilogram of rubber) there is a need for development of efficient system,capable of rapid reduction of COD and BOD. Though the organic load of the rubber efiluent is very high, it does not contain much processed chemicals and therefore it can be considered as a ‘biological eflluent’. Further, the ratio of the Chemical Oxygen Demand to Biological Oxygen Demand (COD/BOD) of this effluent remain almost as a constant value. According to Montgomery (1967), estimation of BOD is not ideally suited for studies on process design, treatability, control of treatment plants, setting standards for treated effluents and assessing the effect of polluting discharges on the oxygen resources of receiving waters. Hence in the present study COD was measured to determine the impact of treatment system on the effluent. In the present study, attempts were made to evaluate the efficiencies of certain methods such as packed bed reactor using immobilized microbial cells, rotating biological contactor (RBC) and activated sludge process, for rapid and efficient treatment of natural rubber latex centrifugation effluent. In addition, studies were also carn'ed out to develop a suitable bioprocess for the coagulation of skim latex, as an alternative to the presently used acid coagulation process towards reducing the pollution load, besides recovering quality rubber

Studies on Advanced Oxidation Processes for the Removal of Acetamiprid from Wastewater

Pollution of water with pesticides has become a threat to the man, material and environment. The pesticides released to the environment reach the water bodies through run off. Industrial wastewater from pesticide manufacturing industries contains pesticides at higher concentration and hence a major source of water pollution. Pesticides create a lot of health and environmental hazards which include diseases like cancer, liver and kidney disorders, reproductive disorders, fatal death, birth defects etc. Conventional wastewater treatment plants based on biological treatment are not efficient to remove these compounds to the desired level. Most of the pesticides are phyto-toxic i.e., they kill the microorganism responsible for the degradation and are recalcitrant in nature. Advanced oxidation process (AOP) is a class of oxidation techniques where hydroxyl radicals are employed for oxidation of pollutants. AOPs have the ability to totally mineralise the organic pollutants to CO2 and water. Different methods are employed for the generation of hydroxyl radicals in AOP systems. Acetamiprid is a neonicotinoid insecticide widely used to control sucking type insects on crops such as leafy vegetables, citrus fruits, pome fruits, grapes, cotton, ornamental flowers. It is now recommended as a substitute for organophosphorous pesticides. Since its use is increasing, its presence is increasingly found in the environment. It has high water solubility and is not easily biodegradable. It has the potential to pollute surface and ground waters. Here, the use of AOPs for the removal of acetamiprid from wastewater has been investigated. Five methods were selected for the study based on literature survey and preliminary experiments conducted. Fenton process, UV treatment, UV/ H2O2 process, photo-Fenton and photocatalysis using TiO2 were selected for study. Undoped TiO2 and TiO2 doped with Cu and Fe were prepared by sol-gel method. Characterisation of the prepared catalysts was done by X-ray diffraction, scanning electron microscope, differential thermal analysis and thermogravimetric analysis. Influence of major operating parameters on the removal of acetamiprid has been investigated. All the experiments were designed using central compoiste design (CCD) of response surface methodology (RSM). Model equations were developed for Fenton, UV/ H2O2, photo-Fenton and photocatalysis for predicting acetamiprid removal and total organic carbon (TOC) removal for different operating conditions. Quality of the models were analysed by statistical methods. Experimental validations were also done to confirm the quality of the models. Optimum conditions obtained by experiment were verified with that obtained using response optimiser. Fenton Process is the simplest and oldest AOP where hydrogen peroxide and iron are employed for the generation of hydroxyl radicals. Influence of H2O2 and Fe2+ on the acetamiprid removal and TOC removal by Fenton process were investigated and it was found that removal increases with increase in H2O2 and Fe2+ concentration. At an initial concentration of 50 mg/L acetamiprid, 200 mg/L H2O2 and 20 mg/L Fe2+ at pH 3 was found to be optimum for acetamiprid removal. For UV treatment effect of pH was studied and it was found that pH has not much effect on the removal rate. Addition of H2O2 to UV process increased the removal rate because of the hydroxyl radical formation due to photolyis of H2O2. An H2O2 concentration of 110 mg/L at pH 6 was found to be optimum for acetamiprid removal. With photo-Fenton drastic reduction in the treatment time was observed with 10 times reduction in the amount of reagents required. H2O2 concentration of 20 mg/L and Fe2+ concentration of 2 mg/L was found to be optimum at pH 3. With TiO2 photocatalysis improvement in the removal rate was noticed compared to UV treatment. Effect of Cu and Fe doping on the photocatalytic activity under UV light was studied and it was observed that Cu doping enhanced the removal rate slightly while Fe doping has decreased the removal rate. Maximum acetamiprid removal was observed for an optimum catalyst loading of 1000 mg/L and Cu concentration of 1 wt%. It was noticed that mineralisation efficiency of the processes is low compared to acetamiprid removal efficiency. This may be due to the presence of stable intermediate compounds formed during degradation Kinetic studies were conducted for all the treatment processes and it was found that all processes follow pseudo-first order kinetics. Kinetic constants were found out from the experimental data for all the processes and half lives were calculated. The rate of reaction was in the order, photo- Fenton>UV/ H2O2>Fenton> TiO2 photocatalysis>UV. Operating cost was calculated for the processes and it was found that photo-Fenton removes the acetamiprid at lowest operating cost in lesser time. A kinetic model was developed for photo-Fenton process using the elementary reaction data and mass balance equations for the species involved in the process. Variation of acetamiprid concentration with time for different H2O2 and Fe2+ concentration at pH 3 can be found out using this model. The model was validated by comparing the simulated concentration profiles with that obtained from experiments. This study established the viability of the selected AOPs for the removal of acetamiprid from wastewater. Of the studied AOPs photo- Fenton gives the highest removal efficiency with lowest operating cost within shortest time.

Sono, Photo and Sonophoto Catalytic Removal of Chemical and Bacterial Pollutants from Wastewater

The term ‘water pollution’ broadly refers to the contamination of water and water bodies (e.g. lakes, rivers, oceans, groundwater etc). Water pollution occurs when pollutants are discharged directly or indirectly into water bodies without adequate treatment to remove the harmful contaminants. This affects not only the plants and organisms living in these bodies of water but also the entire natural biological communities and the biodiversity.Advanced Oxidation Processes (AOPs) have been tested as environment-friendly techniques for the treatment of contaminated water, in view of their ability to convert pollutants into harmless end products. These techniques refer to a set of treatment procedures designed to remove organic or inorganic contaminants in wastewater by oxidation. The contaminants are oxidized by different reagents such as air, oxygen, ozone, and hydrogen peroxide which are introduced in precise, preprogrammed dosages, sequences and combinations under appropriate conditions. The procedure when combined with light in presence of catalyst is known as photocatalysis. When ultrasound (US) is used as the energy source, the process is referred as sonication. Sonication in presence of catalyst is referred as sonocatalysis. Of late, combination of light and sound as energy sources has been tested for the decontamination of wastewater in the presence of suitable catalyst. In this case, the process is referred as sonophotocatalysis. These AOPs are specially advantageous in pollution control and waste water treatment because unlike many other technologies, they do not just transfer the pollutant from one phase to another but completely degrade them into innocuous substances such as CO2 and H2O.

Numerical Feasibility Study for Treated Wastewater Recharge as a Tool to Impede Saltwater Intrusion in the Coastal Aquifer of Gaza – Palestine

The ongoing depletion of the coastal aquifer in the Gaza strip due to groundwater overexploitation has led to the process of seawater intrusion, which is continually becoming a serious problem in Gaza, as the seawater has further invaded into many sections along the coastal shoreline. As a first step to get a hold on the problem, the artificial neural network (ANN)-model has been applied as a new approach and an attractive tool to study and predict groundwater levels without applying physically based hydrologic parameters, and also for the purpose to improve the understanding of complex groundwater systems and which is able to show the effects of hydrologic, meteorological and anthropogenic impacts on the groundwater conditions. Prediction of the future behaviour of the seawater intrusion process in the Gaza aquifer is thus of crucial importance to safeguard the already scarce groundwater resources in the region. In this study the coupled three-dimensional groundwater flow and density-dependent solute transport model SEAWAT, as implemented in Visual MODFLOW, is applied to the Gaza coastal aquifer system to simulate the location and the dynamics of the saltwater–freshwater interface in the aquifer in the time period 2000-2010. A very good agreement between simulated and observed TDS salinities with a correlation coefficient of 0.902 and 0.883 for both steady-state and transient calibration is obtained. After successful calibration of the solute transport model, simulation of future management scenarios for the Gaza aquifer have been carried out, in order to get a more comprehensive view of the effects of the artificial recharge planned in the Gaza strip for some time on forestall, or even to remedy, the presently existing adverse aquifer conditions, namely, low groundwater heads and high salinity by the end of the target simulation period, year 2040. To that avail, numerous management scenarios schemes are examined to maintain the ground water system and to control the salinity distributions within the target period 2011-2040. In the first, pessimistic scenario, it is assumed that pumping from the aquifer continues to increase in the near future to meet the rising water demand, and that there is not further recharge to the aquifer than what is provided by natural precipitation. The second, optimistic scenario assumes that treated surficial wastewater can be used as a source of additional artificial recharge to the aquifer which, in principle, should not only lead to an increased sustainable yield of the latter, but could, in the best of all cases, revert even some of the adverse present-day conditions in the aquifer, i.e., seawater intrusion. This scenario has been done with three different cases which differ by the locations and the extensions of the injection-fields for the treated wastewater. The results obtained with the first (do-nothing) scenario indicate that there will be ongoing negative impacts on the aquifer, such as a higher propensity for strong seawater intrusion into the Gaza aquifer. This scenario illustrates that, compared with 2010 situation of the baseline model, at the end of simulation period, year 2040, the amount of saltwater intrusion into the coastal aquifer will be increased by about 35 %, whereas the salinity will be increased by 34 %. In contrast, all three cases of the second (artificial recharge) scenario group can partly revert the present seawater intrusion. From the water budget point of view, compared with the first (do nothing) scenario, for year 2040, the water added to the aquifer by artificial recharge will reduces the amount of water entering the aquifer by seawater intrusion by 81, 77and 72 %, for the three recharge cases, respectively. Meanwhile, the salinity in the Gaza aquifer will be decreased by 15, 32 and 26% for the three cases, respectively.

Wastewater Treatment Project for Palma Soriano, Cuba: Assessment of Cultural and Ecological Conditions

The Palma Project is an experiment in the use of cultural identity as a social trigger to address ecological degradation. The research methodology draws from environmental, social and urban analyses to unveil the best strategy to address the ecological, river restoration and water treatment challenges in Berkeley, California’s “Sister City” in southeast Cuba, Palma Soriano. The objective is to provide a better quality of life and to create new opportunities for the local community to reconnect with natural cycles of water and the cultivation of their own land. The project aim is to promote the strength and capacity of local communities to protect their own environment based upon a master plan, which includes natural wastewater treatment, reforestation, urban agriculture and the facilitation and utilization of a public space bordering the major river which flows by Palma Soriano, the Cauto. This project will contribute and produce healthy water recycling for Palma, provide a potable water source for the city, encourage ecological restoration of the riparian zone of the Cauto, and provide new opportunities for food production. It is designed to preserve the cultural identity of the local community, and to restore the essential balance between the community’s need to sustain both itself and the natural environment.

Wastewater usage in urban and peri-urban agricultural production systems: scenarios from India

The role urban and peri-urban agriculture (UPA) plays in reducing urban poverty and ensuring environmental sustainability was recognized by the Millennium Development Goals (MGDs). India is the world’s largest democratic nation with a population of 1.2 billion. The rapid urbanization and high proportion of people below the poverty line along with higher migration to urban areas make India vulnerable to food crisis and urbanization of poverty. Ensuring jobs and food security among urban poor is a major challenge in India. The role of UPA can be well explained and understood in this context. This paper focuses on the current situation of UPA production in India with special attention to wastewater irrigation. This question is being posed about the various human health risks from wastewater irrigation which are faced by farmers and labourers, and, secondly by consumers. The possible health hazards involve microbial pathogens as well as helminth (intestinal parasites). Based on primary and secondary data, this paper attempts to confirm that UPA is one of the best options to address increasing urban food demand and can serve to complement rural supply chains and reduce ecological food prints in India. “Good practice urban and peri-urban agriculture” necessitates an integrated approach with suitable risk reduction mechanisms to improve the efficiency and safety of UPA production.

Application of a support system to the design of wastewater treatment plants

This paper presents a case study that explores the advantages that can be derived from the use of a design support system during the design of wastewater treatment plants (WWTP). With this objective in mind a simplified but plausible WWTP design case study has been generated with KBDS, a computer-based support system that maintains a historical record of the design process. The study shows how, by employing such a historical record, it is possible to: (1) rank different design proposals responding to a design problem; (2) study the influence of changing the weight of the arguments used in the selection of the most adequate proposal; (3) take advantage of keywords to assist the designer in the search of specific items within the historical records; (4) evaluate automatically the compliance of alternative design proposals with respect to the design objectives; (5) verify the validity of previous decisions after the modification of the current constraints or specifications; (6) re-use the design records when upgrading an existing WWTP or when designing similar facilities; (7) generate documentation of the decision making process; and (8) associate a variety of documents as annotations to any component in the design history. The paper also shows one possible future role of design support systems as they outgrow their current reactive role as repositories of historical information and start to proactively support the generation of new knowledge during the design process

Adsorbents a partir de fangs biològics excedents de depuradora mitjançant l'aplicació de microones: estudi d'obtenció, caracterització i aplicació en fase líquida

El fang biològic es produeix en les plantes de tractament d'aigües residuals urbanes i industrials. El tractament i la gestió dels fangs és un dels problemes més importants en el camp del tractament de les aigües residuals. Aquesta situació es preveu que es veurà agreujada en el futur, per un increment del volum de fang produït associat a l'exigència de nivells més alts de depuració i per l'augment dels nombre d'estacions depuradores en funcionament. D'altre banda, les limitacions que presenten les opcions tradicionals de gestió dels fangs, fa necessari buscar solucions innovadores i efectives per a solucionar el problema que suposa la gestió d'aquests fangs biològics. Els fangs biològics són de naturalesa carbonosa i amb un alt contingut de matèria orgànica. Aquestes característiques, permeten la conversió del fang en un sòlid adsorbent de tipus carbonós. Aquesta conversió ofereix el doble benefici de reduir el volum de fang que ha de ser gestionat i alhora produir un adsorbent amb un cost inferior a la dels adsorbents convencionals (carbons actius comercials). Fins el moment, els tractaments alta temperatura han demostrat la seva efectivitat per du a terme el procés de transformació dels excedents de fang biològic en un sòlid adsorbent carbonós (carbó actiu). Com a alternativa a aquests processos a alta temperatura, es proposa un nou procés d'obtenció d'un sòlid adsorbent carbonós a partir dels excedents de fangs biològics, mitjançant un tractament a baixa temperatura, combinant el tractament per microones amb l'addició d'un reactiu químic (H2SO4). La present tesi analitza el tractament dels excedents de fangs biològics utilitzant un tractament mitjançant microones i l'addició d'àcid sulfúric (H2SO4), al mateix temps analitza la possibilitat d'utilitzar els sòlids adsorbents obtinguts per a millorar la qualitat de les aigües residuals. Paràmetres d'operació com poden ser la quantitat d'àcid sulfúric addicionada al fang, el nivell de potència del forn microones i el temps de tractament, es modificaran per tal de determinar la influència que poden tenir sobre la qualitat del sòlid adsorbent. Un cop determinada la qualitat dels diferent sòlids adsorbents s'avalua la seva capacitat per a l'eliminació de colorant i metalls en fase líquida. Els resultats obtinguts es comparen amb els obtinguts per un carbó actiu derivat de fangs i un carbó actiu comercial.

Avaluació de la toxicitat de metalls pesants i arsènic en diferents models biològics

En aquest estudi, la toxicitat de diversos metalls pesants i l'arsènic va ser analitzada utilitzant diferents models biològics. En la primera part d'aquest treball, el bioassaig de toxicitat Microtox, el qual està basat en la variació de l'emissió lumínica del bacteri luminiscent Vibrio fischeri, va ser utilitzat per establir les corbes dosi-resposta de diferents elements tòxics com el Zn(II), Pb(II), Cu(II), Hg(II), Ag(I), Co(II), Cd(II), Cr(VI), As(V) i As(III) en solucions aquoses. Els experiments es varen portar a terme a pH 6.0 i 7.0 per tal de mostrar que el pH pot influir en la toxicitat final mesurada d'alguns metalls degut als canvis relacionats amb la seva especiació química. Es varen trobar diferents tipus de corbes dosi-resposta depenent del metall analitzat i el pH del medi. En el cas de l'arsènic, l'efecte del pH en la toxicitat de l'arsenat i l'arsenit es va investigar utilitzant l'assaig Microtox en un rang de pHs comprès entre pH 5.0 i 9.0. Els valors d'EC50 determinats per l'As(V) disminueixen, reflectint un augment de la toxicitat, a mesura que el pH de la solució augmenta mentre que, en el cas de l'As(III), els valors d'EC50 quasi bé no varien entre pH 6.0 i 8.0 i només disminueixen a pH 9.0. HAsO42- i H2AsO3- es varen definir com les espècies més tòxiques. Així mateix, una anàlisi estadística va revelar un efecte antagònic entre les espècies químiques d'arsenat que es troben conjuntament a pH 6.0 i 7.0. D'altra banda, els resultats de dos mètodes estadístics per predir la toxicitat i les possibles interaccions entre el Co(II), Cd(II), Cu(II), Zn(II) i Pb(II) en mescles binàries equitòxiques es varen comparar amb la toxicitat observada sobre el bacteri Vibrio fischeri. L'efecte combinat d'aquests metalls va resultar ser antagònic per les mescles de Co(II)-Cd(II), Cd(II)-Zn(II), Cd(II)-Pb(II) i Cu(II)-Pb(II), sinèrgic per Co(II)-Cu(II) i Zn(II)-Pb(II) i additiu en els altres casos, revelant un patró complex de possibles interaccions. L'efecte sinèrgic de la combinació Co(II)-Cu(II) i la forta disminució de la toxicitat del Pb(II) quan es troba en presència de Cd(II) hauria de merèixer més atenció quan s'estableixen les normatives de seguretat ambiental. La sensibilitat de l'assaig Microtox també va ser determinada. Els valors d'EC20, els quals representen la toxicitat llindar mesurable, varen ser determinats per cada element individualment i es va veure que augmenten de la següent manera: Pb(II) < Ag(I) < Hg(II)  Cu(II) < Zn(II) < As(V) < Cd(II)  Co(II) < As(III) < Cr(VI). Aquests valors es varen comparar amb les concentracions permeses en aigues residuals industrials establertes per la normativa oficial de Catalunya (Espanya). L'assaig Microtox va resultar ser suficientment sensible per detectar els elements assajats respecte a les normes oficials referents al control de la contaminació, excepte en el cas del cadmi, mercuri, arsenat, arsenit i cromat. En la segona part d'aquest treball, com a resultats complementaris dels resultats previs obtinguts utilitzant l'assaig de toxicitat aguda Microtox, els efectes crònics del Cd(II), Cr(VI) i As(V) es varen analitzar sobre la taxa de creixement i la viabilitat en el mateix model biològic. Sorprenentment, aquests productes químics nocius varen resultar ser poc tòxics per aquest bacteri quan es mesura el seu efecte després de temps d'exposició llargs. Tot i això, en el cas del Cr(VI), l'assaig d'inhibició de la viabilitat va resultar ser més sensible que l'assaig de toxicitat aguda Microtox. Així mateix, també va ser possible observar un clar fenomen d'hormesis, especialment en el cas del Cd(II), quan s'utilitza l'assaig d'inhibició de la viabilitat. A més a més, diversos experiments es varen portar a terme per intentar explicar la manca de toxicitat de Cr(VI) mostrada pel bacteri Vibrio fischeri. La resistència mostrada per aquest bacteri podria ser atribuïda a la capacitat d'aquest bacteri de convertir el Cr(VI) a la forma menys tòxica de Cr(III). Es va trobar que aquesta capacitat de reducció depèn de la composició del medi de cultiu, de la concentració inicial de Cr(VI), del temps d'incubació i de la presència d'una font de carboni. En la tercera part d'aquest treball, la línia cel·lular humana HT29 i cultius primaris de cèl·lules sanguínies de Sparus sarba es varen utilitzar in vitro per detectar la toxicitat llindar de metalls mesurant la sobreexpressió de proteines d'estrès. Extractes de fangs precedents de diverses plantes de tractament d'aigues residuals i diferents metalls, individualment o en combinació, es varen analitzar sobre cultius cel·lulars humans per avaluar el seu efecte sobre la taxa de creixement i la capacitat d'induir la síntesi de les proteïnes Hsp72 relacionades amb l'estrès cel·lular. No es varen trobar efectes adversos significatius quan els components s'analitzen individualment. Nogensmenys, quan es troben conjuntament, es produeix un afecte advers sobre tan la taxa de creixement com en l'expressió de proteins d'estrès. D'altra banda, cèl·lules sanguínies procedents de Sparus sarba es varen exposar in vitro a diferents concentracions de cadmi, plom i crom. La proteïna d'estrès HSP70 es va sobreexpressar significativament després de l'exposició a concentracions tan febles com 0.1 M. Sota les nostres condicions de treball, no es va evidenciar una sobreexpressió de metal·lotioneïnes. Nogensmenys, les cèl·lules sanguínies de peix varen resultar ser un model biològic interessant per a ser utilitzat en anàlisis de toxicitat. Ambdós models biològics varen resultar ser molt adequats per a detectar acuradament la toxicitat produïda per metalls. En general, l'avaluació de la toxicitat basada en l'anàlisi de la sobreexpressió de proteïnes d'estrès és més sensible que l'avaluació de la toxicitat realitzada a nivell d'organisme. A partir dels resultats obtinguts, podem concloure que una bateria de bioassaigs és realment necessària per avaluar acuradament la toxicitat de metalls ja que existeixen grans variacions entre els valors de toxicitat obtinguts emprant diferents organismes i molts factors ambientals poden influir i modificar els resultats obtinguts.

Integrated management of urban wastewater systems: a model-based approach

The main objective pursued in this thesis targets the development and systematization of a methodology that allows addressing management problems in the dynamic operation of Urban Wastewater Systems. The proposed methodology will suggest operational strategies that can improve the overall performance of the system under certain problematic situations through a model-based approach. The proposed methodology has three main steps: The first step includes the characterization and modeling of the case-study, the definition of scenarios, the evaluation criteria and the operational settings that can be manipulated to improve the system’s performance. In the second step, Monte Carlo simulations are launched to evaluate how the system performs for a wide range of operational settings combinations, and a global sensitivity analysis is conducted to rank the most influential operational settings. Finally, the third step consists on a screening methodology applying a multi-criteria analysis to select the best combinations of operational settings.

Metodologia de disseny conceptual d'estacions depuradores d'aigües residuals que combina el procés de decisió jeràrquic amb l'anàlisi de decisions multicriteri

La present tesi proposa una metodologia de disseny conceptual d'estacions depuradores d'aigües residuals (EDAR) mitjançant la combinació del procés de decisió jeràrquic i l'anàlisi de decisions multicriteri. El document s'inicia amb una breu introducció als principals camps abordats pel treball: el disseny dels processos químics en general, el disseny de les estacions depuradores d'aigües residuals en particular, i l'anàlisi de decisions multicriteri aplicada a la gestió ambiental. Seguidament, es fixen els objectius del treball i es descriuen tant la metodologia com el material de suport informàtic utilitzats. Per validar i contrastar la metodologia de disseny presentada, es desenvolupa un cas d'estudi on es porta a terme el disseny conceptual d'una EDAR que presenta els mateixos requeriments que l'EDAR que opera actualment al municipi de Granollers. Inicialment es presenta la informació de partida i tot seguit es defineixen els objectius de disseny, així com el conjunt de criteris que s'utilitzaran per avaluar en quina mesura es compleixen aquests objectius. Els objectius de disseny són de diferents tipus: ambientals, tècnics, socials i econòmics, i el conjunt de criteris utilitzats, concretament 33, també es classifica segons aquestes quatre categories. Cadascun dels criteris presenta un determinat pes d'importància relativa en la presa de decisions. Finalment, es desenvolupa tot el procés de decisió fins a obtenir el disseny complet de l'EDAR. El procés de decisió s'ha dividit en dues parts diferenciades però que alhora s'entrellacen: la línia d'aigua i la línia de fang. El procés de decisió presenta un total de divuit qüestions amb un màxim de quatre alternatives per pregunta (dotze qüestions corresponen a la línia d'aigua, i sis a la línia de fangs). Per solucionar cadascuna d'aquestes qüestions, s'avaluen les alternatives proposades respecte a un conjunt de criteris triats de la llista inicial. Aplicant el procés de decisió multicriteri anomenat SMART (simple multiattribute rating technique), es combinen els resultats de les alternatives respecte a cada criteri, tenint en compte la importància de cada criteri per obtenir un sol valor per alternativa. Per quantificar els criteris referents a l'operació del procés i les de tipus econòmic s'han utilitzat els programes GPS-X i CapdetWorks respectivament. Pel que fa als criteris no quantificats mitjançant aquests programes, s'han resolt de manera qualitativa i mitjançant manuals de disseny i també tenint en compte l'opinió d'experts en aquest camp. L'alternativa que obté un pes més elevat és la recomanada per al procés de decisió. El cas d'estudi finalitza un cop s'obté el disseny complet de l'EDAR. Per integrar tots aquests elements que hem esmentat i donar suport al desenvolupament del procés de decisió s'ha utilitzat el programa DRAMA (Design Rationale Management). A continuació, es fa una anàlisi comparativa entre l'EDAR que hi ha actualment al municipi de Granollers i l'EDAR resultat del cas d'estudi. Es descriu el diagrama de flux que conforma l'EDAR de Granollers i el diagrama de flux de l'EDAR resultat de l'estudi, se'n fa una anàlisi comparativa justificant cadascuna de les decisions preses en el cas d'estudi i, finalment, es fa una discussió de resultats on es reflecteixen els avantatges associats d'aplicar la metodologia de disseny conceptual proposada. Finalment, es presenten les conclusions de la tesi. Els principals resultats de la tesi es van publicar el 2002 a la revista internacional Industrial and Engineering Chemistry Research (N. Vidal, R. Bañares-Alcántara, I. Rodríguez-Roda i M. Poch: "Design of wastewater treatment plants using a conceptual design methodology", Industrial and Engineering Chemistry Research, 41 (20), pàg. 4993-5005) i la continuació de la línia de recerca al Laboratori d'Enginyeria Química i Ambiental de la UdG ha comportat la presentació del treball de recerca de Xavi Flores "Procés de decisió jeràrquic combinat amb anàlisi multicriteri per al suport al disseny conceptual de sistemes de fangs actius d'una estació depuradora d'aigües residuals" i la presentació dels resultats parcials al congrés internacional de la 9th IWA Conference on Design, Operation and Economics of Large Wastewater Treatment, que va tenir lloc el setembre passat a Praga ("Combining hierarchical decision process with multi-criteria analysis for conceptual design of WWTP", X. Flores, N. Vidal, A. Bonmatí, J. B. Copp i I. Rodríguez-Roda).