Operational Cost Reduction in WDM Networks using Lighttours

Wavelength division multiplexing (WDM) networks have been adopted as a near-future solution for the broadband Internet. In previous work we proposed a new architecture, named enhanced grooming (G+), that extends the capabilities of traditional optical routes (lightpaths). In this paper, we compare the operational expenditures incurred by routing a set of demands using lightpaths with that of lighttours. The comparison is done by solving an integer linear programming (ILP) problem based on a path formulation. Results show that, under the assumption of single-hop routing, almost 15% of the operational cost can be reduced with our architecture. In multi-hop routing the operation cost is reduced in 7.1% and at the same time the ratio of operational cost to number of optical-electro-optical conversions is reduced for our architecture. This means that ISPs could provide the same satisfaction in terms of delay to the end-user with a lower investment in the network architecture

Reduction of the Ant Mandible Gap Range After Biotic Homogenization Caused by an Ant Invasion (Hymenoptera: Formicidae)

After most of the native ant species are displaced by the Argentine ant invasion, it is probable that some ecological processes carried out by natives are not replaced. In some cases this could be due to a morphological difference between the Argentine ant and the displaced native ants. The significant decrease in ant richness after the invasion (only two species detected in the invaded zones vs. 25 species in surrounding non-invaded zones) implies a drastic reduction in the ant mandible gap range (the mandible gap spectra of all the ant species in a community) in the invaded zones. This reduction could explain why some roles that were previously carried out by the displaced native species are not performed by the invasive species. This could be due to a functional inability to carry out these activities. The mandible gap waspositively correlated with the ant body mass in the 26 ant species considered. The functional inability hypothesis could be applied to other invasive ants as well as to the Argentine ant

Cu and Co exchanged ZSM-5 zeolites: activity towards no reduction and hydrocarbon oxidation

|Cu x|[Si yAl]-MFI and |Co x|[Si yAl]-MFI catalysts were prepared by ion exchange from |Na|[Si yAl]-MFI zeolites (y = 12, 25 and 45). The activity of the catalysts was evaluated in the reduction of NO to N2 in an oxidative atmosphere using propane or methane as reducing agents. The Cu catalysts were only active with propane and they presented higher activity than the Co-based catalysts, the latter being active with both hydrocarbons. H2-TPR and DRS-UV/Vis data allowed correlation between the activity towards NO reduction and the presence of cationic charge-compensating species in the zeolite. It was also verified that the hydrocarbons are preferentially oxidised by O2, a reaction that occurs simultaneously with their oxidation with NO.

Towards integrated operation of membrane bioreactors : effects of aeration on biological and filtration performance

Two experimental studies evaluated the effect of aerobic and membrane aeration changes on sludge properties, biological nutrient removal and filtration processes in a pilot plant membrane bioreactor. The optimal operating conditions were found at an aerobic dissolved oxygen set-point (DO) of 0.5mgO2L-1 and a membrane specific aeration demand (SADm) of 1mh-1, where membrane aeration can be used for nitrification. Under these conditions, a total flow reduction of 42% was achieved (75% energy reduction) without compromising nutrient removal efficiencies, maintaining sludge characteristics and controlled filtration. Below these optimal operating conditions, the nutrient removal efficiency was reduced, increasing 20% for soluble microbial products, 14% for capillarity suction time and reducing a 15% for filterability. Below this DO set-point, fouling increased with a transmembrane pressure 75% higher. SADm below 1mh-1 doubled the values of transmembrane pressure, without recovery after achieving the initial conditions

Emprego de planejamento fatorial no desenvolvimento de uma metodologia para extração de zinco de resíduos galvânicos

The plating process generates solid waste rich in heavy metals and aiming to reduce environmental impact of such waste, this work suggests a methodology for zinc reduction, through a 2(4) factorial planning, studying the influence of the following variables: acid concentration (15, 20 or 30% v/v), acid type (sulfuric or hydrochloric), acid volume (15, 20 or 25 mL) and extraction time (12, 24 or 36 h). Through this methodology it is possible to establish the optimal conditions (15 mL of a 30% hydrochloric acid concentration during 12 h) to get a 100% efficiency in zinc extraction.

pH effect on the synthesis of magnetite nanoparticles by the chemical reduction-precipitation method

This work aimed at putting in evidence the influence of the pH on the chemical nature and properties of the synthesized magnetic nanocomposites. Saturation magnetization measurements evidenced a marked difference of the magnetic behavior of samples, depending on the final pH of the solution after reaction. Magnetite and maghemite in different proportions were the main magnetic iron oxides actually identified. Synthesis with final pH between 9.7-10.6 produced nearly pure magnetite with little or no other associated iron oxide. Under other synthetic conditions, goethite also appears in proportions that depended upon the pH of the synthesis medium.

Evaluation of sample processing methods for the polar contaminant analysis of sewage sludge using liquid chromatography - mass spectrometry (LC/MS)

Monitoring of sewage sludge has proved the presence of many polar anthropogenic pollutants since LC/MS techniques came into routine use. While advanced techniques may improve characterizations, flawed sample processing procedures, however, may disturb or disguise the presence and fate of many target compounds present in this type of complex matrix before analytical process starts. Freeze-drying or oven-drying, in combination with centrifugation or filtration as sample processing techniques were performed followed by visual pattern recognition of target compounds for assessment of pretreatment processes. The results shown that oven-drying affected the sludge characterization, while freeze-drying led to less analytical misinterpretations.

Effect of dye structure and redox mediators on anaerobic azo and anthraquinone dye reduction

We investigated the biological decolourisation of dyes with different molecular structures. The kinetic constant values (k1) achieved with azo dye Reactive Red 120 were 7.6 and 10.1 times higher in the presence of RM (redox mediators) AQDS and riboflavin, respectively, than the assays lacking RM. The kinetic constant achieved with the azo dye Congo Red was 42 times higher than that obtained with the anthraquinone dye Reactive Blue 4. The effect of RM on dye reduction was more evident for azo dyes resistant to reductive processes, and ineffective for anthraquinone dyes because of the structural stability of the latter.

Nitrous oxide emissions from an intermittent aeration activated sludge system of an urban wastewater treatment plant

This study investigated the emission of N2O during the sequential aerated (60-min) and non-aerated (30-min) stages of an intermittent aeration cycle in an activated sludge wastewater treatment plant (WWTP). N2O emission occurred during both stages; however, emission was much higher during aeration. Air stripping is the major factor controlling transfer of N2O from the sewage to the atmosphere. The N2O emissions exclusively from the aeration tank represented 0.10% of the influent total nitrogen load and the per capita emission factor was almost 3 times higher than that suggested by the IPCC for inventories of N2O emission from WWTPs.

The Methods of Possible Joint Treatment of Manure and Sewage Sludge in the Leningrad Region

The nutrient load to the Gulf of Finland has started to increase as a result of the strong economic recovery in agriculture and livestock farming in the Leningrad region. Also sludge produced from municipal wastewater treatment plant of the Leningrad region causes the great impact on the environment, but still the main options for its treatment is disposal on the sludge beds or Landfills. The aim of this study was to evaluate the implementation of possible joint treatment methods of manure form livestock and poultry enterprises and sewage sludge produced from municipal wastewater treatment plants in the Leningrad region. The study is based on published data. The most attention was put on the anaerobic digestion and incineration methods. The manure and sewage sludge generation for the whole Leningrad region and energy potential produced from their treatment were estimated. The calculations showed that total amount of sewage sludge generation is 1 348 000 t/a calculated on wet matter and manure generation is 3 445 000 t/a calculated on wet matter. The potential heat release from anaerobic digestion process and incineration process is 4 880 000 GJ/a and 5 950 000 GJ/a, respectively. Furthermore, the work gives the overview of the general Russian and Finnish legislation concerning manure and sewage sludge treatment. In the Gatchina district it was chosen the WWTP and livestock and poultry enterprises for evaluation of the centralized treatment plant implementation based on anaerobic digestion and incineration methods. The electricity and heat power of plant based on biogas combustion process is 4.3 MW and 7.8 MW, respectively. The electricity and heat power of plant based on manure and sewage sludge incineration process is 3.0 MW and 6.1 MW, respectively.

Biokaasulaitoksen rejektivesien vaikutus jätevedenpuhdistamon toimintaan ja rejektivesien esikäsittelyn tarpeellisuus

Diplomityön tavoitteena oli tutkia biokaasulaitoksen rejektivesien ominaisuuksiin vaikuttavia tekijöitä ja rejektiveden esikäsittelyn tarpeellisuutta. Lisäksi tavoitteena oli tarkastella Kouvolaan suunnitteilla olevan Kymen Bioenergia Oy:n biokaasulaitoksen rejektivesien vaikutusta Kouvolan Veden Mäkikylän jätevedenpuhdistamolla. Biokaasulaitoksen rejektivedet ovat yhdyskuntajätevesiin verrattuna selvästi konsentroituneempia. Jätevedenpuhdistamoilla erityisesti rejektiveden korkea typpipitoisuus aiheuttaa lisäkuormitusta. Suomessa toiminnassa oleville biokaasulaitoksille tehdyn kyselytutkimuksen tulosten perusteella rejektiveden typpipitoisuuteen vaikuttaa syötteen typpipitoisuus sekä mädätysjäännöksen kuivauksen tehokkuus. Rejektiveden kiintoainepitoisuudella on puolestaan vaikutusta biologiseen hapenkulutukseen ja välillisesti myös rejektiveden kemialliseen hapenkulutukseen. Rejektivesien jätevedenpuhdistamoilla aiheuttamaa kuormitusta on mahdollista vähentää esikäsittelemällä rejektivedet joko biologisella tai fysikaalis-kemiallisella puhdistusmenetelmällä. Kyselytutkimus kuitenkin osoitti, että rejektivesien esikäsittelyssä ei aina päästä puhdistustavoitteeseen. Jätevedenkäsittelyn sijaan rejektivesiä on mahdollista käyttää lannoitteena, mikäli biokaasulaitoksen syöte ei sisällä jätevedenpuhdistamon lietteitä. Myös Kouvolan Veden Mäkikylän puhdistamolla biokaasulaitoksen rejektivedet tulevat lisäämään merkittävästi tulovirtaaman typpikuormaa. Typpikuorman lisäys edellyttää ilmastusaltaassa ilmastuksen tehostamista sekä kalkin syöttömäärän lisäämistä, jotta jäteveden happipitoisuus ja pH pysyvät typenpoistoreaktioille suotuisina. Lisäksi tulovirtaamasta puolet tullaan ohjaamaan esiselkeyttimen ohi, jotta ilmastusaltaassa on orgaanista ainetta typenpoistoon riittävästi. Mäkikylän puhdistamon typenpoistokapasiteettia on mahdollista kasvattaa lisähiilen syötöllä. Mikäli biokaasulaitoksen kapasiteettilisäyksen jälkeen rejektivesien typpikuoma ylittää lisähiilellä saavutetun lisäkapasiteetin, on rejektivedet esikäsiteltävä.

Electrochemical evidence of sulfinic acid derivative as an intermediate in the reduction of aromatic sulfonyl chloride in an aprotic medium

The electrochemical reduction of p-nitrobenzenesulfonyl chloride (NBSCl) in dimethylsulfoxide (DMSO) solution is used here as a model to investigate the role of sulfinic acid derivative in this compound's global reduction process. Cyclic voltammetric experiments reveal the production of sulfinic acid derivative, which is important in chemical reactions involving the original compound and other intermediates. This paper also discusses the probable mechanisms of the reduction.

Role of oxidation-reduction cycle of iron in direct leaching of zinc concentrate

Direct leaching is an alternative to conventional roast-leach-electrowin (RLE) zinc production method. The basic reaction of direct leach method is the oxidation of sphalerite concentrate in acidic liquid by ferric iron. The reaction mechanism and kinetics, mass transfer and current modifications of zinc concentrate direct leaching process are considered. Particular attention is paid to the oxidation-reduction cycle of iron and its role in direct leaching of zinc concentrate, since it can be one of the limiting factors of the leaching process under certain conditions. The oxidation-reduction cycle of iron was experimentally studied with goal of gaining new knowledge for developing the direct leaching of zinc concentrate. In order to obtain this aim, ferrous iron oxidation experiments were carried out. Affect of such parameters as temperature, pressure, sulfuric acid concentration, ferrous iron and copper concentrations was studied. Based on the experimental results, mathematical model of the ferrous iron oxidation rate was developed. According to results obtained during the study, the reaction rate orders for ferrous iron concentration, oxygen concentration and copper concentration are 0.777, 0.652 and 0.0951 respectively. Values predicted by model were in good concordance with the experimental results. The reliability of estimated parameters was evaluated by MCMC analysis which showed good parameters reliability.

Adsorption isotherm studies of BOD, TSS and colour reduction from palm oil mill effluent (POME) using boiler fly ash

Palm oil is one of the two most important vegetable oils in the world's oil and fats market. The extraction and purification processes generate different kinds of waste generally known as palm oil mill effluent (POME). Earlier studies had indicated the possibility of using boiler fly ash to adsorb impurities and colour in POME treatment. The adsorption treatment of POME using boiler fly ash was further investigated in detail in this work with regards to the reduction of BOD, colour and TSS from palm oil mill effluent. The amount of BOD, colour and TSS adsorbed increased as the weight of the boiler fly ash used was increased. Also, the smaller particle size of 425µm adsorbed more than the 850µm size. Attempts were made to fit the experimental data with the Freundlich, Langmuir and Dubinin-Radushkevich isotherms. The R² values, which ranged from 0.8974-0.9898, 0.8848-0.9824 and 0.6235-0.9101 for Freundlich, Langmuir and Dubinin-Radushkevich isotherms respectively, showed that Freundlich isotherm gave a better fit followed by Langmuir and then Dubinin-Radushkevich isotherm. The sorption trend could be put as BOD > Colour > TSS. The apparent energy of adsorption was found to be 1.25, 0.58 and 0.97 (KJ/mol) for BOD, colour and TSS respectively, showing that sorption process occurs by physiosorption. Therefore, boiler fly ash is capable of reducing BOD, Colour and TSS from POME and hence could be used to develop a good adsorbent for POME treatment.

In vivo sensitivity reduction of Puccinia triticina races, causal agent of wheat leaf rust, to DMI and QoI fungicides

Experiments were carried out to determine in vivo the IC50 and the IC90 for demethylation-inhibitor fungicides (DMIs, triazoles) and quinone outside inhibitors (QoIs, strobilurins) to the five most frequent races of Puccinia triticina in 2007 growing season in Southern Brazil. The tests were done in a greenhouse with wheat seedlings. DMI fungicides were tested at the concentrations, in mg/L, 0.0; 0.02; 0.2; 2.0; 20.0; 100.0 and 200.0, and QoIs at the concentrations 0.0; 0.0001; 0.001; 0.01; 0.1; 1 and 10.0 mg of active ingredient/L water. Fungicides were preventively applied at 24 hours before the inoculation of seedlings with the fungal spores. The effect of treatments was assessed based on the number of uredia/cm². The lowest IC50 (inhibitory concentration) for DMI fungicides determined for MCG-MN, sensitive race, ranged from 0.33 to 0.91 mg/L, while the highest values for MDP-MR, MDT-MR, MDK-MR, MFH-HT races, varied from 9.63 to 85.64 mg/L (suspected insensitivity). QoI fungicide presented an IC50 varying from 0.0018 to 0.14 mg/L. The sensitivity reduction factor for DMIs varied from 8.8 to 238.8, and for QoIs from 0.3 to 1.5 mg/L. Sensitivity reduction was confirmed for the races MDP-MR, MDT-MR, MDK-MR, MFH-HT to DMIs, as well as their sensitivity to QoI fungicides.