Electrocatalytic reduction of CO2 to formate using particulate Sn electrodes: Effect of metal loading and particle size

The development of electrochemical processes for the conversion of CO2 into value-added products allows innovative carbon capture & utilization (CCU) instead of carbon capture & storage (CCS). In addition, coupling this conversion with renewable energy sources would make it possible to chemically store electricity from these intermittent renewable sources. The electroreduction of CO2 to formate in aqueous solution has been performed using Sn particles deposited over a carbon support. The effect of the particle size and Sn metal loading has been evaluated using cyclic voltammetry and chronoamperometry. The selected electrode has been tested on an experimental filter-press type cell system for continuous and single pass CO2 electroreduction to obtain formate as main product at ambient pressure and temperature. Experimental results show that using electrodes with 0.75 mg Sn cm−2, 150 nm Sn particles, and working at a current density of 90 mA cm−2, it is possible to achieve rates of formate production over 3.2 mmol m−2 s−1 and faradaic efficiencies around 70% for 90 min of continuous operation. These experimental conditions allow formate concentrations of about 1.5 g L−1 to be obtained on a continuous mode and with a single pass of catholyte through the cell.

The effect of truck size and weight on accident experience and traffic operations. Volume 1: executive summary. Final report.

Federal Highway Administration, Washington, D.C.

The effect of truck size and weight on accident experience and traffic operations. Volume II: traffic operations. Final report.

Federal Highway Administration, Washington, D.C.

The effect of truck size and weight on accident experience and traffic operations. Volume III: accident experience of large trucks. Final report.

Federal Highway Administration, Washington D.C.

The effect of truck size and weight on accident experience and traffic operations. Volume IV: truck exposure classification by size and weight. Final report.

Federal Highway Administration, Washington, D.C.

The effect of variable mesh size on the stability of multistep methods /

Bibliography: leaf 33.

Using the effect size to model change in preference values from descriptive health status

Objectives: This pilot study describes a modelling approach to translate group-level changes in health status into changes in preference values, by using the effect size (ES) to summarize group-level improvement. Methods: ESs are the standardized mean difference between treatment groups in standard deviation (SD) units. Vignettes depicting varying severity in SD decrements on the SF-12 mental health summary scale, with corresponding symptom severity profiles, were valued by a convenience sample of general practitioners (n = 42) using the rating scale (RS) and time trade-off methods. Translation factors between ES differences and change in preference value were developed for five mental disorders, such that ES from published meta-analyses could be transformed into predicted changes in preference values. Results: An ES difference in health status was associated with an average 0.171-0.204 difference in preference value using the RS, and 0.104-0.158 using the time trade off. Conclusions: This observed relationship may be particular to the specific versions of the measures employed in the present study. With further development using different raters and preference measures, this approach may expand the evidence base available for modelling preference change for economic analyses from existing data.

"mind the gap": The size-distance dissociation in visual neglect is a cueing effect

There is a growing body of evidence that the processes mediating the allocation of spatial attention within objects may be separable from those governing attentional distribution between objects. In the neglect literature, a related proposal has been made regarding the perception of (within-object) sizes and (between-object) distances. This proposal follows observations that, in size-matching and bisection tasks, neglect is more strongly expressed when patients are required to attend to the sizes of discrete objects than to the (unfilled) distances between objects. These findings are consistent with a partial dissociation between size and distance processing, but a simpler alternative must also be considered. Whilst a neglect patient may fail to explore the full extent of a solid stimulus, the estimation of an unfilled distance requires that both endpoints be inspected before the task can be attempted at all. The attentional cueing implicit in distance estimation tasks might thus account for their superior performance by neglect patients. We report two bisection studies that address this issue. The first confirmed, amongst patients with left visual neglect, a reliable reduction of rightward error for unfilled gap stimuli as compared with solid lines. The second study assessed the cause of this reduction, deconfounding the effects of stimulus type (lines vs. gaps) and attentional cueing, by applying an explicit cueing manipulation to line and gap bisection tasks. Under these matched cueing conditions, all patients performed similarly on line and gap bisection tasks, suggesting that the reduction of neglect typically observed for gap stimuli may be attributable entirely to cueing effects. We found no evidence that a spatial extent, once fully attended, is judged any differently according to whether it is filled or unfilled.

The effect of temperature on the size and population density of dinoflagellates in larvae of the reef coral Porites astreoides

Pre-settlement events play an important role in determining larval success in marine invertebrates with bentho-pelagic life histories, yet the consequences of these events typically are not well understood. The purpose of this study was to examine the pre-settlement impacts of different seawater temperatures on the size and population density of dinoflagellate symbionts in brooded larvae of the Caribbean coral Porites astreoides. Larvae were collected from P. astreoides at 14-20 m depth on Conch Reef (Florida) in June 2002, and incubated for 24 h at 15 temperatures spanning the range 25.1 degrees-30.0 degrees C in mean increments of 0.4 +/- 0.1 degrees C (+/- SD). The most striking feature of the larval responses was the magnitude of change in both parameters across this 5 degrees C temperature range within 24 h. In general, larvae were largest and had the highest population densities of Symbiodinium sp. between 26.4 degrees-27.7 degrees C, and were smallest and had the lowest population densities at 25.8 degrees C and 28.8 degrees C. Larval size and symbiont population density were elevated slightly (relative to the minimal values) at the temperature extremes of 25.1 degrees C and 30 degrees C. These data demonstrate that coral larvae are highly sensitive to seawater temperature during their pelagic phase, and respond through changes in size and the population densities of Symbiodinium sp. to ecologically relevant temperature signals within 24 h. The extent to which these changes are biologically meaningful will depend on the duration and frequency of exposure of coral larvae to spatio-temporal variability in seawater temperature, and whether the responses have cascading effects on larval success and their entry to the post-settlement and recruitment phase.

The effect of manganese on the grain size of commercial AZ31 alloy

The effect of manganese on gain refinement of a commercial AZ31 alloy has been investigated using an Al-60%Mn master alloy splatter as an alloying additive at 730 degrees C in aluminium titanite crucibles. It is shown that grain refinement by manganese is readily achievable in AZ31. Electron microprobe analyses reveal that prior to the addition of extra manganese the majority of the intermetallic particles found in AZ31 are of the AL(8)Mn(5) type. However, after the addition of extra manganese in the range from 0.1% to 0.8%, the predominant group of intermetallic particles changes to the metastable AlMn type. This leads to a hypothesis that the metastable AlMn intermetallic particles are more effective than Al8Mn5 as nucleation sites for magnesium grains. The hypothesis is supported by the observation that a long period of holding at 730 degrees C leads to an increase in grain size, due probably to the transformation of the metastable AlMn to the stable Al8Mn5. The hypothesis has also been used to understand the mechanism of grain refinement by superheating.

Effect of growing site, moisture stress and seed size on viability and dormancy of Sporobolus pyramidalis (giant rats tail grass) seed

Sporobolus pyramidalis P. Beauv (giant rats tail grass) is a serious agricultural and environmental weed in tropical and subtropical areas of Australia. Infestations of this unpalatable plant reduce the productivity of pastures and the profitability of industries dependent on grazing animals. This paper reports a series of studies undertaken to assist in the development of control strategies for this species. In particular, these studies measured the viability and dormancy status of fresh seed of S. pyramidalis and the decline of dormancy with time. Variability in these characteristics was determined in seeds collected from several sites within south-east Queensland. The effect of moisture availability during the inflorescence and seed production phases on seed viability and dormancy was also determined. The dormancy of freshly collected seed from several sites ranged from 15 to 95%, but decreased to negligible levels after 4-6 months. Seeds that matured under conditions of high moisture availability were initially more dormant than seeds matured where moisture was less readily available. The proportion of viable seeds was significantly lower in smaller than larger seeds even though viability for all seed sizes exceeded 90%. This study has shown that seed of S. pyramidalis generally has high viability with a large proportion of the seed germinable soon after maturity.

Effect of fluoromica platelet size on the properties of segmented polyurethane nanocomposites

Segmented polyurethane nanocomposites containing three different size fractions of SomasifTM ME100 (synthetic fluoromica) have been prepared via solvent casting. The platelet size was adjusted via a proprietary milling process, and average diameters of approximately 500 nm, 100 nm and 30 nm were measured via TEM. To the best of our knowledge this is the first time the effect of aspect ratio has been studied with the same t-o-t structured mineral. The mechanical properties of these nanocomposites have been found to be highly dependent upon the platelet size. Depending on the aspect ratio and surface treatment selected, significant improvements in tensile strength can be achieved with a minimal reduction in resilience: a problem encountered with elastomeric layered silicate nanocomposites.