Sensitivity of wear rates in the micro-scale abrasion test to test conditions and material hardness

Micro-scale abrasion (ball cratering) tests were performed with different combinations of ball and bulk specimen materials, under different test conditions, such as load and abrasive slurry concentration. Wear modes were classified into two types: with rolling particle motion and with grooving particle motion. Wear rates observed with rolling particle motion were relatively insensitive to test conditions, whereas with grooving motion they varied much more. It is suggested that rolling abrasion is therefore a more appropriate mode if reproducible test results are desired. The motion of the abrasive particles can be reliably predicted from the knowledge of hardnesses and elastic properties of the ball and the specimen, and from the normal load and the abrasive slurry concentration. General trends in wear resistance measured in the micro-scale abrasion test with rolling particle motion are similar to those reported in tests with fixed abrasives with sliding particle motion, although the variation in wear resistance with hardness is significantly smaller. © 2004 Published by Elsevier B.V.

Sources of variability in the free-ball micro-scale abrasion test

In the 'free-ball' version of the micro-scale abrasion or ball-cratering test the rotating ball rests against a tilted sample and a grooved drive shaft. Tests under nominally identical conditions with different apparatus commonly show small but significant differences in measured wear rate. An indirect method has been developed and demonstrated for continuous on-line measurement of the coefficient of friction in the free-ball test. Experimental investigation of the effects of sample tilt angle and drive shaft groove width shows that both these factors influence the stability of the rotation of the ball, and the shape of the abrasive slurry pool, which in turn affect the coefficient of friction in the wear scar area and the measured wear rate. It is suggested that in order to improve the reproducibility of this method the geometry of the apparatus should be specified. For the apparatus used in this work with a steel ball of 25 mm diameter, a sample tilt angle of 60-75° and a shaft groove width of about 10mm provided the most stable ball motion and a wear rate which showed least variability. © 2004 Elsevier B.V. All rights reserved.

The effect of nozzle design on laser micro-machining of M2 tool steels

This paper shows how computational techniques have been used to develop axi-symmetric, straight, sonic-line, minimum length micro nozzles that are suitable for laser micro-machining applications. Gas jets are used during laser micro-machining processing applications to shield the interaction zone between laser and workpiece material, and they determine the machining efficiency of such applications. The paper discusses the nature of laser-material interactions and the importance of using computational fluid dynamics to model pressure distributions in short nozzles that are used to deliver gas to the laser-material interaction zone. Experimental results are presented that highlight unique problems associated with laser micro machining using gas jets.

Efeitos de diferentes doses de rosuvastatina no metabolismo lipídico e dos carboidratos, morfometria do tecido adiposo e remodelamento cardíaco de camundongos C57BL/6 alimentados com dieta hiperlipídica

Existe uma significativa associação entre a prevalência de doenças cardiovasculares e a síndrome metabólica. Evidências mostram que a obesidade está associada a alterações estruturais e funcionais do coração. As estatinas podem reduzir a síntese endógena de colesterol e, portanto, são utilizadas como uma importante ferramenta contra a hipercolesterolemia em pacientes obesos. O presente trabalho tem como objetivo estudar os efeitos da rosuvastatina no metabolismo lipídico e dos carboidratos, morfometria do tecido adiposo e no remodelamento cardíaco de camundongos alimentados com uma dieta hiperlipídica. Neste trabalho foram utilizados 50 camundongos distribuidos em cinco grupos: grupo controle (alimentado com dieta padrão), grupo hiperlipídico (alimentado com dieta hipelipídica 60%), grupo hiperlipídico + rosuvastatina 10 (alimentado com dieta hipelipídica 60% - acrescido de 10 mg de rosuvastatina), grupo hiperlipídico + rosuvastatina 20 (alimentado com dieta hipelipídica 60% - acrescido de 20 mg de rosuvastatina), grupo hiperlipídico + rosuvastatina 40 (alimentado com dieta hipelipídica 60% - acrescido de 40 mg de rosuvastatina). Foram estudados os efeitos do tratamento com diferentes doses de rosuvastatina na massa corporal, metabolismo dos carboidratos e lipídios, pressão arterial, remodelamento na estrutura cardíaca e mudanças ultraestruturais no coração de camundongos C57BL / 6 machos alimentados com uma dieta hiperlipídica. O tratamento com rosuvastatina reduziu os níveis de lípidos no sangue, melhorou a resistência à insulina e diminuiu a pressão arterial dos camundongos alimentados com dieta rica em lipídeos. Além disso, atenuou o remodelamento cardíaco, diminuindo a fibrose intersticial e perivascular, e manteve a integridade morfológica mitocondrial, com menor produção de proteina desacopladora-2 (UCP2). Assim, a rosuvastatina tem efeitos benéficos sobre as alterações metabólicas dos carboidratos e lipídios, e no remodelamento cardíaco induzidas por dieta hiperlipídica.