CT and PET/CT Hybrid Imaging of Coronary Artery Disease

Coronary artery disease (CAD) is a chronic process that evolves over decades and may culminate in myocardial infarction (MI). While invasive coronary angiography (ICA) is still considered the gold standard of imaging CAD, non-invasive assessment of both the vascular anatomy and myocardial perfusion has become an intriguing alternative. In particular, computed tomography (CT) and positron emission tomography (PET) form an attractive combination for such studies. Increased radiation dose is, however, a concern. Our aim in the current thesis was to test novel CT and PET techniques alone and in hybrid setting in the detection and assessment of CAD in clinical patients. Along with diagnostic accuracy, methods for the reduction of the radiation dose was an important target. The study investigating the coronary arteries of patients with atrial fibrillation (AF) showed that CAD may be an important etiology of AF because a high prevalence of CAD was demonstrated within AF patients. In patients with suspected CAD, we demonstrated that a sequential, prospectively ECG-triggered CT technique was applicable to nearly 9/10 clinical patients and the radiation dose was over 60% lower than with spiral CT. To detect the functional significance of obstructive CAD, a novel software for perfusion quantification, CarimasTM, showed high reproducibility with 15O-labelled water in PET, supporting feasibility and good clinical accuracy. In a larger cohort of 107 patients with moderate 30-70% pre-test probability of CAD, hybrid PET/CT was shown to be a powerful diagnostic method in the assessment of CAD with diagnostic accuracy comparable to that of invasive angiography and fractional flow reserve (FFR) measurements. A hybrid study may be performed with a reasonable radiation dose in a vast majority of the cases, improving the performance of stand-alone PET and CT angiography, particularly when the absolute quantification of the perfusion is employed. These results can be applied into clinical practice and will be useful for daily clinical diagnosis of CAD.

Usability of laser–arc hybrid welding processes in industrial applications

Metal industries producing thick sections have shown increasing interest in the laser–arc hybrid welding process because of its clear advantages compared with the individual processes of autogenous laser welding and arc welding. One major benefit of laser–arc hybrid welding is that joints with larger gaps can be welded with acceptable quality compared to autogenous laser welding. The laser-arc hybrid welding process has good potential to extend the field of applications of laser technology, and provide significant improvements in weld quality and process efficiency in manufacturing applications. The objective of this research is to present a parameter set-up for laser–arc hybrid welding processes, introduce a methodical comparison of the chosen parameters, and discuss how this technology may be adopted in industrial applications. The research describes the principles, means and applications of different types of laser–arc hybrid welding processes. Conducted experiment processing variables are presented and compared using an analytical model which can also be used for predictive simulations. The main argument in this thesis is that profound understanding of the advanced technology of laser-arc hybrid welding will help improve the productivity of welding in industrial applications. Based on a review of the current knowledge base, important areas for further research are also identified. This thesis consists of two parts. The first part introduces the research topic and discusses laser–arc hybrid welding by characterizing its mechanism and most important variables. The second part comprises four research papers elaborating on the performance of laser– arc hybrid welding in the joining of metals. The study uses quantitative and qualitative research methods which include in-depth, interpretive analyses of results from a number of research groups. In the interpretive analysis, the emphasis is placed on the relevance and usefulness of the investigative results drawn from other research publications. The results of this study contribute to research on laser–arc hybrid welding by increasing understanding of how old and new perspectives on laser–arc hybrid welding are evidenced in industry. The research methodology applied permits continued exploration of how laser–arc hybrid welding and various process factors influence the overall quality of the weld. Thestudy provides a good foundation for future research, creates improved awareness of the laser–arc hybrid welding process, and assists the metal industry to maximize welding productivity.

Learning Robot Environment through Simulation

Traditionally simulators have been used extensively in robotics to develop robotic systems without the need to build expensive hardware. However, simulators can be also be used as a “memory”for a robot. This allows the robot to try out actions in simulation before executing them for real. The key obstacle to this approach is an uncertainty of knowledge about the environment. The goal of the Master’s Thesis work was to develop a method, which allows updating the simulation model based on actual measurements to achieve a success of the planned task. OpenRAVE was chosen as an experimental simulation environment on planning,trial and update stages. Steepest Descent algorithm in conjunction with Golden Section search procedure form the principle part of optimization process. During experiments, the properties of the proposed method, such as sensitivity to different parameters, including gradient and error function, were examined. The limitations of the approach were established, based on analyzing the regions of convergence.

Hybrid warfare – just a twist of compound warfare? : views on warfare from the United States Armed Forces perspective

The wars the Western armies are involved with today are different from those that were fought in the end of 20th century. To explain this change, the Western military thinkers have come up with various different types of definitions of warfare over the last 30 years, each describing the tendencies involved in the conflicts of the time. The changing nature of conflicts surfaced a new term – hybrid warfare. The term was to describe and explain the multi-modality and complexity of modern day conflict. This thesis seeks the answer for the question: what is the development of thought behind hybrid warfare? In this thesis the Vietnam War (1965-1975) is used as an example of compound warfare focusing on the American involvement in the war. The Second Lebanon War (2006) serves as an example of hybrid warfare. Both case studies include an irregular opposing force, namely National Liberation Front in Vietnam War and Hezbollah in the Second Lebanon War. These two case studies are compared with the term full spectrum operations introduced in the current U.S. Department of Army Field Manual No. 3-0 Operations to see the differences and similarities of each term. The perspective of this thesis is the American point of view. This thesis concludes that hybrid warfare, compound warfare and full spectrum operations are very similar. The first two terms are included in the last one. Although hybrid warfare is not officially defined, it will most likely remain to be used in the discussion in the future, since hybrid wars and hybrid threats are officially accepted terms.

Design and development of the architecture of an agricultural mobile robot

Parameters such as tolerance, scale and agility utilized in data sampling for using in Precision Agriculture required an expressive number of researches and development of techniques and instruments for automation. It is highlighted the employment of methodologies in remote sensing used in coupled to a Geographic Information System (GIS), adapted or developed for agricultural use. Aiming this, the application of Agricultural Mobile Robots is a strong tendency, mainly in the European Union, the USA and Japan. In Brazil, researches are necessary for the development of robotics platforms, serving as a basis for semi-autonomous and autonomous navigation systems. The aim of this work is to describe the project of an experimental platform for data acquisition in field for the study of the spatial variability and development of agricultural robotics technologies to operate in agricultural environments. The proposal is based on a systematization of scientific work to choose the design parameters utilized for the construction of the model. The kinematic study of the mechanical structure was made by the virtual prototyping process, based on modeling and simulating of the tension applied in frame, using the.

Quality of papaya hybrid grown under different irrigation depths

Irrigation is a practice widely used in fruit production in the Brazilian Northeast region, including in the papaya crop in order to increase their productivity. For the purpose of knowing the productive potential of papaya hybrid irrigated, an experiment was carried out in order to evaluate the performance of a papaya hybrid under different irrigations depths. Four irrigation depths (50, 75, 100 and 125% of ETo) were tested and the reference evapotranspiration was calculated by the Penman-Monteith model. The hybrid papaya used was UENF/Caliman 01, which was planted in single rows, spaced 4 x 2m from each other, and irrigated by dripping. The experimental design in randomized blocks was used with six replications and three plants per plot. The following variables were evaluated: transversal diameter, longitudinal diameter, pulp thickness, external and internal appearances, soluble solids, titratable acidity, pulp pH and soluble solids/titratable acidity relation. The higher transversal and longitudinal diameters of the fruit were obtained applying an irrigation depth of about 108% of evapotranspiration. The UENF/Caliman 01 hybrid can be cultivated in the semiarid region of the State of Paraiba, Brazil, with replacement rate of 100% ETo, without compromising the quality of the fruits.

Initial development of two eucalyptus hybrid submitted to irrigation

The eucalyptus offers several advantages compared to other forestry species and, by using the irrigation can increase productivity and decrease production time. The objective of the present study was to evaluate two hybrid eucalyptus (Grancam and Urograndis), no irrigation, dripping and micro sprinkler irrigated at 90, 120, 150 and 180 days after transplanting (DAT). The experiment was conducted at the experimental irrigation area in the State University of Mato Grosso do Sul, in the municipality of Aquidauna - State of MS, Brazil. The experimental design was randomized blocks, split plot with four blocks and two replications within each block, and the plots were composed by irrigation treatments (dripping, micro sprinkler irrigate and dry) and the subplots the hybrids (Grancam and Urograndis).The total area of the experiment had 3 hectares, where each plot consisted of 1 ha. It was evaluated plant height, stem diameter and canopy, stem basal area, the relationship between height and stem diameter, the relationship between height and canopy diameter and stem volume. Data were subjected to analysis of variance and compared by Tukey test at 5% probability. Irrigation systems and dripping sprinkle provide greater plant height, stem diameter, canopy diameter, stem basal area and stem volume.

Feasibility study of metal to polymer hybrid joining

The increasing demand for lightweight components has led to a huge exploitation of non-metallic materials such as polymers, fibers and elastomers in industrial and manufacturing processes. Recent trends towards cost effectiveness, weight reduction and production flexibility in industrial production and manufacturing processes has led to a growing interest in hybrid components where two or more dissimilar materials coexist to achieving specifically optimized characteristics. The importance of this research is to serve as a bridge to understanding the theories behind various joining techniques and the adaptation of the process for metal to polymer hybrid joints. Moreso, it helps companies to select the most productive and yet economical joining process for realization of lightweight metal to polymer hybrid components. This thesis is a literature review analyzing various materials that has been published on various joining methods for metal to polymer hybrid joints on the feasibility and eventual realization of the joint between these dissimilar materials. This study is aimed at theoretically evaluating the feasibility of joining processes between metal and plastic components by exploiting exhaustively joining and welding sources.

Design and implementation of robot gripper interface

This thesis presents a design for an asynchronous interface to Robotiq adaptive gripper s-model. Designed interface is a communication layer that works on top of modbus layer. The design contains function definitions, finite state machine and exceptions. The design was not fully implemented but enough was so that it can be used. The implementation was done with c++ in linux environment. Additionally to the implementation a simple demo program was made to show the interface is used. Also grippers closing speed and force were measured. There is also a brief introduction into robotics and robot grasping.

Design and Control of Permanent Magnet Synchronous Machine for Hybrid Electric Vehicle

This master’s thesis mainly focuses on the design requirements of an Electric drive for Hybrid car application and its control strategy to achieve a wide speed range. It also emphasises how the control and performance requirements are transformed into its design variables. A parallel hybrid topology is considered where an IC engine and an electric drive share a common crank shaft. A permanent magnet synchronous machine (PMSM) is used as an electric drive machine. Performance requirements are converted into Machine design variables using the vector model of PMSM. Main dimensions of the machine are arrived using analytical approach and Finite Element Analysis (FEA) is used to verify the design and performance. Vector control algorithm was used to control the machine. The control algorithm was tested in a low power PMSM using an embedded controller. A prototype of 10 kW PMSM was built according to the design values. The prototype was tested in the laboratory using a high power converter. Tests were carried out to verify different operating modes. The results were in agreement with the calculations.

Comparison of Classical and Secondary Cytologic Criteria Relative to Hybrid Capture for Diagnosing Cervical-vaginal Infection by Human Papillomavirus

Objective To compare the diagnostic accuracy of the classic Meisels cytologic criteria and the Schneider secondary criteria relative to the hybrid capture method for diagnosing HPV infection. Methods This was a retrospective study performed at a public university hospital. A total of 41 patients with a cytologic diagnosis of HPV infection and 40 HPV-negative patients were selected for review of the cervical-vaginal smears seeking to classical and secondary criteria. A single pathologist reviewed the slides in search of the criteria. The classical and secondary cytologic criteria were compared with the hybrid capture for diagnosing HPV infection. Bartleti test was applied for the age analysis, and Fisher's exact test was used to compare proportions. The tests were considered significant when the probability of rejecting the null hypothesis was less than 5% (p < 0.05). Results The Meisels criteria were less sensitive (34.0%) than the secondary Schneider criteria (57.5%) when compared with the hybrid capture (p < 0.0001), although the specificity of the former criteria was non-significantly higher (91.2% and 67.7%, respectively). In cases of moderate or intense inflammation, the sensitivity and specificity of the Schneider criteria were decreased, 33.3% and 50.0% respectively (p = 0.0115). Conclusions Compared with hybrid capture for diagnosis of HPV infection, the sensitivity of the secondary Schneider criteria was higher than the classical Meisels criteria.Moderate or intense inflammation reduces the sensitivity and specificity of the secondary Schneider criteria for diagnosing HPV infection using the hybrid capture as the gold standard.

Laser-TIG–hybridihitsauksen soveltuvuustutkimus

Tässä tutkimuksessa selvitetään ilman hitsauslisäainetta tapahtuvan laser–TIG–hybridihitsausprosessin soveltuvuus 6 mm ja 8 mm paksujen päittäisliitettyjen S355 K2 ja Laser 355 MC rakenneterästen hitsaukseen. Hitsien tarkastelussa huomio kiinnitetään hitsausnopeuteen, hitsien tunkeumaan, liittämistehokkuuteen, hitsien kovuuteen ja hitsausliitoksen ulkonäköön. Muita tutkittavia asioita ovat laser-TIG-hybridihitsattujen levyjen muodonmuutokset ja suuresta hitsausnopeudesta sekä pienestä t8/5 jäähtymisajasta johtuvat mahdolliset kylmähalkeamat. Laser-TIG-hybridihitsejä verrataan robotti-MAG- ja käsin MAG-hitseihin sekä kaarihitsausstandardin SFS-EN ISO 5817 hitsiluokkien mukaisiin raja-arvoihin. Laser-TIG-hybridihitsausprosessissa TIG-valokaari mahdollistaa tasaisen ja lähes roiskeettoman hitsin ja lasersäde aikaansaa syvän tunkeuman sekä tasalaatuisen juurihitsin. Laser-TIG-hybridihitsausprosessilla 6 mm paksut S355 K2 rakenneteräslevyt on mahdollista hitsata levyn yhdeltä puolelta kerralla valmiiksi. Paksummat 8 mm levyt voidaan hitsata levyn yhdeltä tai molemmilta puolilta suoritettavalla laser-TIG-hybridihitsauksella. Laser-TIG-hybridihitsausprosessilla hitsatut hitsit ovat hyvin siistejä ja lähes roiskeettomia. Verrattaessa laser-TIG-hybridihitsausprosessia muihin hitsausprosesseihin sen voidaan todeta olevan erittäin kilpailukykyinen 6 mm paksujen päittäisliitettyjen rakenneterästen hitsaamisessa, mutta se soveltuu myös 8 mm paksujen rakenneterästen hitsaamiseen. Tutkitut hitsit täyttävät kaarihitsausstandardin SFS-EN ISO 5817 B- ja D-hitsiluokkien mukaiset raja-arvot. Vertailukokeet 6 mm paksulla S355 rakenneteräksellä osoittavat, että yhdeltä puolelta suoritettavan laser-TIG-hybridihitsauksen hitsausnopeus on robotti-MAG-hitsaukseen verrattuna yli nelinkertainen ja MAG-käsinhitsaukseen verrattuna yli viisinkertainen. Laser-TIG-hybridihitsauksessa liittämistehokkuus on noin viisinkertainen robotti-MAGhitsaukseen verrattuna. Molemmilta puolilta suoritettavalla laser-TIG-hybridihitsauksella voidaan 8 mm paksulla S355 rakenneteräksellä saavuttaa noin kolminkertainen hitsausnopeus ja liittämistehokkuus robotti-MAG-hitsaukseen verrattuna. Laser-TIG-hybridihitsauksessa TIG-kaaren tuoman lisälämmön ansiosta suurillakin hitsausnopeuksilla (1 m/min) voidaan saavuttaa edulliset kovuusarvot. Kovuusmittausten tulosten perusteella 6 mm ja 8 mm paksujen S355 K2 ja Laser 355 MC rakenneterästen hitsit eivät ylittäneet kaarihitsausstandardin määrittelemää 350 HV kovuuden enimmäisrajaa. Laser-TIG-hybridihitsauksen edullisesta lämmöntuonnista johtuen levyjen pituus- ja poikittaissuuntaiset muodonmuutokset ovat noin 80 prosenttia pienemmät kuin käsin suoritettavassa MAG-hitsauksessa. Laser-TIG-hybridihitsausprosessilla käytetään I-railoa, mutta robotti-MAG- ja käsin MAG-hitsausprosesseilla joudutaan käyttämään V-railoa, jolloin lämmöntuonti ja siitä johtuvat muodonmuutokset ovat suuremmat. Korkea liittämistehokkuus ja edullinen lämmöntuonti merkitsevät vähäisempiä muodonmuutoksia ja siten merkittäviä säästöjä työ-, materiaali- ja energiakustannuksissa. 8 mm ja sitä paksummilla S355 rakenneteräksillä levyn yhdeltä puolelta suoritettava päittäisliitoksen hitsaaminen on laser-TIG hybridihitsauksella haastavaa, koska yli 200 A:n TIG-kaarivirralla suuri metallisula aiheuttaa avaimenreiän sulkeutumisen ja avaimenreiän alaosaan muodostuu kaasukuplia. Tästä voidaan tehdä sellainen johtopäätös, että päittäisliitettävien levyjen ilmarakoa pitäisi kasvattaa niin suureksi, että avaimenreiän sulavirtaus ei pääse estymään. Yli 0,25 mm:n ilmarako edellyttää lasersäteen vaaputusta tai säteen halkaisijan kasvattamista. Ilmaraon kasvattaminen edellyttää myös lisäaineen käyttöä. Tutkimustulosten perusteella laser-TIG-hybridihitsausprosessilla voidaan saavuttaa merkittäviä etuja ja kustannussäästöjä, joten sen hyödyntämistä kannattaa harkita 8 mm ja sitä ohuempien päittäisliitettävien tuotteiden konepaja- ja tehdastuotannossa. Laser-TIGhybridihitsausprosessi soveltuu esimerkiksi seuraavien tuotteiden hitsaamiseen: päittäisliitettävät levyt, palkit, koneenosat, putket, säiliöt ja erilaiset pyörähdyskappaleet.

Laser-TIG hybrid welding process

Joining processes and techniques need to meet the trend of new applications and the development of new materials. The application in connection with thick and thin plates in industrial fields is wide and the joining technology is in very urgent need. The laser-TIG hybrid welding technology can play the respective advantages of both of them. One major advantage of the hybrid laser-TIG welding technology is its efficient use of laser energy. Additionally, it can develop into a high and new advanced welding technology and become a hot spot in both the application and research area. This thesis investigated laser –TIG hybrid welding with the aim of enlightening the reader on its advantages, disadvantages and future areas of improvement. The main objective is to investigate laser-TIG hybrid on the welding of various metals (steels, magnesium, aluminium etc.). In addition, it elaborates on various possible combinations on hybrid laser-TIG welding technology and their benefits. The possibility of using laser-TIG hybrid in welding of thick materials was investigated. The method applied in carrying out this research is by using literature review. The results showed that hybrid laser-TIG is applicable to almost all weldable metals. Also it proves to be effective in welding refractive metals. The possibility of welding with or without filler materials is of economic advantage especially in welding of materials with no filler material. Thick plate’s hybrid laser-TIG welding is showing great prospects although it normally finds its used in welding thin materials in the range of 0.4 to 0.8 mm. The findings show that laser-TIG hybrid welding can be a versatile welding process and therefore will be increasingly used industrially due to its numerous advantages and the development of new TIG arc that enhances its capabilities.

Hezbollah and Taliban - hybrid adversaries in contemporary conflicts? : views on an adversary from the United States Armed Forces perspective

The experiences of the United States Armed Forces of the wars in Iraq and Afghanistan and Israel Defense Forces in the Second Lebanon War resulted a new term to surface called “hybrid warfare”. It was to describe the complexity of today’s battlefield. The term “hy-brid warfare” was never officially defined nor is it today. The updated version of the US ARMY Field Manual 3-0: Operations (Change 1) from February 22, 2011, introduced and defined “hybrid threat” and thus opened the discussion for hybrid adversary. In this thesis a model is introduced according to which any organization, group or an ad-versary can be examined and evaluated to see whether it qualifies as a hybrid adversary. It is demonstrated by the example of Hezbollah, which is recognized as the best example of an organization utilizing “hybrid warfare” and subsequently categorizing as a hybrid adver-sary. The model will be tested with Afghan Taliban to see whether both the model works and Taliban qualifies as a hybrid adversary or not. According to the model used in this thesis, it is concluded that Taliban does not meet the standards of a hybrid adversary, but with acquisition of standoff weapons it would quickly qualify as one. The model proved to work, and it could be used as a tool by intelligence of-ficers for estimating the threat levels of any group or identifying those groups that are al-ready or are about to develop into a hybrid adversary.

Dynamic optimization for the trajectory planning of robot manipulators in the presence of obstacles

This paper presents an approach to the solution of moving a robot manipulator with minimum cost along a specified geometric path in the presence of obstacles. The main idea is to express obstacle avoidance in terms of the distances between potentially colliding parts. The optimal traveling time and the minimum mechanical energy of the actuators are considered together to build a multiobjective function. A simple numerical example involving a Cartesian manipulator arm with two-degree-of-freedom is described.