Obtenção de filtro cerâmico a partir da diatomita e casca de arroz carbonizada visando tratamento de efluente têxtil

The effluents released by the textile industry have high concentrations of alkali, carbohydrates, proteins, in addition to colors containing heavy metals. Therefore, a filter was prepared aiming primarily to the removal of color. In order to prepare this filter, rice hulls and diatomite were used, which have in their structure, basically amorphous hydrated silica. The silica exists in three crystalline forms: quartz, tridymite and cristobalite. In accordance with the above considerations, this study was divided into two stages; the first corresponds to the preparation of the filter and the second to carry out the tests in the effluent/filter in order to verify the efficiency of the color removal. First, the raw material was subjected to a chemical analysis and XRD, and then the diatomite was mixed, via humid, with a planetarium windmill with 20 %, 40 %, 60 % and 80 % of rice husk ash. To the mixture, 5 % carboxymethylcellulose (CMC) was added as a binder at room temperature. The samples were uniaxially compacted into metallic matrix of 0.3 x 0.1 cm² of area at a pressure of 167 MPa by means of hydraulic press and then sintered at temperatures of 1,000 °C, 1,200 °C and 1,400 °C for 1 h and submitted to granulometry test using laser, linear retraction, water absorption, apparent porosity and resistance to bending, DTA, TMA and XRD. To examine the pore structure of the samples scanning electron microscope (SEM) was used. Also tests were carried out in a mercury porosimeter to verify the average size of the pores and real density of the samples. In the second stage, samples of the effluent were collected from a local industry, whose name will be preserved, located in Igapó, in the State of Rio Grande do Norte - RN. The effluent was first pretreated before filtration and then subjected to a treatment of flotation. The effluent was then characterized before and after filtration, with parameters of color, turbidity, suspended solids, pH, chemical and biochemical oxygen demand (COD and BOD). Thus, through the XRD analysis the formation of cristobalite α in all samples was observed. The best average size of pore was found to be 1.75 μm with 61.04 % apparent porosity, thus obtaining an average 97.9 % color removal and 99.8 % removal of suspended solid

Avaliação de concretos reforçados por confinamento com manta de fibra de vidro estrutural e pré-impreganada

Due to the occurrence of diseases in the use of structural reinforcements in composites, with presentation of concrete blanket detachment, has been identified the need to evaluate the performance of concrete reinforced with glass fiber. This study aims to evaluate these concretes by means of testing methodologies, using concrete with low resistance with structural reinforcement for confinement by preimpregnated glass fiber and traditional fiberglass blanket. The first stage of work was the development of methodologies for analysis, opting for four types, such as the acoustic survey, strength to compressive, the pull-off and ultrasound. Next, tests were carried out using the four selected methodologies in 30 of proof-of-specimens by 5x10 cm, 15 were reinforced with the traditional fiberglass blanket with 5specimens exposed to test a marine environment of marine coastline of Natal-RN and 15 were reinforced with a pre-impregnated glass fiber blanket, as well as 5specimens exposed to a test environment of the marine coastline of Natal-RN. After conducting the acoustic survey, it has been verified a lack of delaminating and air bubbles in the samples, confirming the absence of gross shortcomings in the implementation of the ribs both the traditional fiberglass blanket and in the preimpregnated fiber glass blanket. After carrying out methods of pull-off and compressive strengthening test it was observed that the reinforced proof-bodies with pre-impregnated glass blanket showed maximum stresses higher than the traditional fiberglass blanket; consequently a greater grip with the formation of a smaller area of . fracture, unlike traditional glass mat, which showed lower maximum stresses, with a greater area of fracture. It was also found that the traditional fiberglass blanket presented detachment of blanket-concrete interface, unlike the pre-impregnated fiberglass blanket, which showed a better grip on the blanket-concrete interface. In the trial of ultrasound there was no presence of cracks in the blanket-concrete interface, yielding to both blankets good compactness of the concrete. At the end of this work, they were developed and proposed two methods of testing for evaluation of reinforced concrete structures with composites, for standardization, the acoustic survey and pull-off

Estudo comparativo de pás para aerogeradores de grande porte fabricadas em materiais compósitos reforçadas com fibra de carbono ou fibra de vidro

The research and development of wind turbine blades are essential to keep pace with worldwide growth in the renewable energy sector. Although currently blades are typically produced using glass fiber reinforced composite materials, the tendency for larger size blades, particularly for offshore applications, has increased the interest on carbon fiber reinforced composites because of the potential for increased stiffness and weight reduction. In this study a model of blade designed for large generators (5 MW) was studied on a small scale. A numerical simulation was performed to determine the aerodynamic loading using a Computational Fluid Dynamics (CFD) software. Two blades were then designed and manufactured using epoxy matrix composites: one reinforced with glass fibers and the other with carbon fibers. For the structural calculations, maximum stress failure criterion was adopted. The blades were manufactured by Vacuum Assisted Resin Transfer Molding (VARTM), typical for this type of component. A weight comparison of the two blades was performed and the weight of the carbon fiber blade was approximately 45% of the weight of the fiberglass reinforced blade. Static bending tests were carried out on the blades for various percentages of the design load and deflections measurements were compared with the values obtained from finite element simulations. A good agreement was observed between the measured and calculated deflections. In summary, the results of this study confirm that the low density combined with high mechanical properties of carbon fibers are particularly attractive for the production of large size wind turbine blades

Estudo da potencialidade da incorporação de resíduo de granito e da queima da casca do café em cerâmica vermelha

The industrial production of ornamental rocks and the burning of coffee husk generate waste that is discarded into the environment. However, with the study of the incorporation of these residues in ceramic products, may be found an alternative to reducing environmental impacts and detrimental effects on human health caused by its indiscriminate disposal of waste in nature. Thus, this work aimed to study the addition of ashes of the coffee husk and granite residue in matrix of red ceramic. The raw materials were dry milled and sieved to mesh 100. To characterize the raw materials were carried out analyzes of X-ray diffraction (XRD), X-ray fluorescence (XRF), particle size analysis (PSA), differential thermal analysis (DTA) and thermogravimetric analysis (TG). Six formulations were prepared where the clay content was kept constant (70%wt) and ashes contents and granite residue varied from 10, 15, 20 and 30%. Dilatometrics analyzes were performed at four selected formulations, containing them: 100% clay (A100); 70% clay and 30% ashes (A70C30); 70% clay and 30% granite residue (A70G30); and 70% clay, 15% granite residue and 15% ashes (A70G15C15). The samples were prepared by uniaxial compaction with pressure of 25 MPa, and fired at temperatures of 800°C, 850ºC, 900ºC, 950ºC, 1000ºC and 1100°C. Assays were performed to determine the linear shrinkage of burning (LSB), water absorption (WA), apparent porosity (AP), density (D) and tensile bending. Also were performed analyzes of X-ray diffraction (XRD) and scanning electron microscopy (SEM) of the samples fired. The formulations incorporating granite residue and/or ashes reached the required limits of water absorption according to NBR 15270-1 and NBR 15310 and tensile bending according to classical literature (SANTOS, 1989) necessary for the production of tiles and ceramic block for masonry sealing

Adição de subprodutos da cinza da casca de café (coffea canephora) em massa cerâmica para porcelanato

To produce porcelain tiles fluxing agents are used in order to obtain a liquid phase during firing. This liquid phase fills the pores decreasing porosity, water absorption and contributes to material densification. In the porcelain tiles industry, feldspar is the main flux material used, with quantities ranging between 35 and 50%. Studies focus on the discovery of materials with flux characteristics that can reduce the consumption of feldspar by porcelain tiles industry. In this context, the coffee husk ashes, a residue obtained when coffee husks are burned to produce heat for the dryers during the processing of the green fruit, have as main chemical constituents potassium, calcium and magnesium, giving them characteristics of fluxing material. Brazil is the largest coffee producer in the world and is responsible for over 30% of the world s production. In this work a physical treatment of coffee husk ash was carried out in order to eliminate the organic matter and, after this, two by-products were obtained: residual wastes R1 and R2. Both residues were added separately as single fluxes and also in association with feldspar in mixtures with raw materials collected in a porcelain industry located in Dias d Ávila-Ba. The addition of these residues aimed to contribute to the reduction of the consumption of feldspar in the production of porcelain tiles. Specimens were produced with dimensions of 60 mm x 20 mm x 6 mm in an uniaxial die with compacting pressure of 45 MPa. The samples were heated to a temperature of 1200 °C, for 8 minutes. Tests were performed to characterize the raw materials by XRF, XRD, particle size analysis, DTA and TGA and, additionally, the results of the physical properties of water absorption, apparent porosity, linear shrinkage, density, dilatometry, flexural strength and SEM of sintered body were analyzed. Additions of less than 8% of the residue R1 contributed to the decrease of porosity, but the mechanical strength of the samples was not satisfactory. Additions of 5% the R2 residue contributed significantly to decrease the water absorption and apparent porosity, and also to increase the mechanical strength. Samples with addition of feldspar associated with the R2 residue, in proportions of 6.7% of R2 and 6.7% of feldspar, led to results of water absorption of 0.12% and mechanical strength of 46 MPa, having parameters normalized to the manufacture of porcelain stoneware tiles

Efeito da adição do poli(etileno acrilato de metila) (ema) e da fibra de linter de algodão nas propriedades do poli(tereftalato de etileno) reciclado (petrec)

The development of new materials to fill the demand of technological advances is a challenge for many researchers around the world. Strategies such as making blends and composites are promising alternatives to produce materials with different properties from those found in conventional polymers. The objective of this study is to evaluate the effect of adding the copolymer poly(ethylene methyl acrylate) (EMA) and cotton linter fibers (LB) on the properties of recycled poly(ethylene terephthalate) (PETrec) by the development of PETrec/EMA blend and PETrec/EMA/LB blend composite. In order to improve the properties of these materials were added as compatibilizers: Ethylene - methyl acrylate - glycidyl methacrylate terpolymer (EMA-GMA) and maleic anhydride grafted polyethylene (PE-g-MA). The samples were produced using a single screw extruder and then injection molded. The obtained materials were characterized by thermogravimetry (TG), melt flow index (MFI) mensurements, torque rheometry, pycnometry to determinate the density, tensile testing and scanning electron microscopy (SEM). The rheological results showed that the addition of the EMA copolymer increased the viscosity of the blend and LB reduces the viscosity of the blend composite. SEM analysis of the binary blend showed poor interfacial adhesion between the PETrec matrix and the EMA dispersed phase, as well as the blend composite of PETrec/EMA/LB also observed low adhesion with the LB fiber. The tensile tests showed that the increase of EMA percentage decreased the tensile strength and the Young s modulus, also lower EMA percentage samples had increased the elongation at break. The blend composite showed an increase in the tensile strength and in the Young`s modulus, and a decrease in the elongation at break. The blend formulations with lower EMA percentages showed better mechanical properties that agree with the particle size analysis which showed that these formulations presented a smaller diameter of the dispersed phase. The blend composite mechanical tests showed that this material is stronger and stiffer than the blend PETrec/EMA, whose properties have been reduced due to the presence of EMA rubbery phase. The use of EMA-GMA was effective in reducing the particle size of the EMA dispersed phase in the PETrec/EMA blend and PE-g-MA showed evidences of reaction with LB and physical mixture with the EMA

Desenvolvimento e caracterização de compósito a partir da borra da piaçava para construção da parábola de um fogão solar a concentração

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Adsorção de cobre e cromo utilizando fibra de sisal visando o tratamento da água produzida pela indústria petrolífera

Currently, the oil industry is the biggest cause of environmental pollution. The objective was to reduce the concentration of copper and chromium in the water produced by the oil industry. It was used as adsorbent natural sisal fiber Agave sp treated with nitric acid and sodium hydroxide. All vegetable fibers have physical and morphological properties that enablies the adsorption of pollutants. The basic composition of sisal is cellulose, hemicellulose and lignin. The features are typically found in the characterization of vegetable fibers, except the surface area that was practically zero. In the first stage of adsorption, it was evaluated the effect of temperature and time skeeking to optimize the execution of the factorial design. The results showed that the most feasible fiber was the one treated with acid in five hours (30°C). The second phase was a factorial design, using acid and five hours, this time was it determined in the first phase. The tests were conducted following the experimental design and the results were analyzed by statistical methods in order to optimize the main parameters that influence the process: pH, concentration (mol / L) and fiber mass/ metal solution volume. The volume / mass ratio factor showed significant interference in the adsorption process of chromium and copper. The results obtained after optimization showed that the highest percentages of extraction (98%) were obtained on the following operating conditions: pH: 5-6, Concentration: 100 ppm and mass/ volume: 1 gram of fiber/50mL solution. The results showed that the adsorption process was efficient to remove chromium and copper using sisal fibers, however, requiring further studies to optimize the process.

Estudo de efeitos de um extrato aquoso de farinha de casca de maracujá (Passiflora edulis f. flavicarpa) na marcação de constituintes sangüíneos com Tecnécio 99m, na morfometria das hemácias e na biodisponibilidade do radiofármaco Pertecnetato de Sódio em ratos Wistar

Blood constituents labelled with technetium-99m (99mTc) has been used with radiobiocomplexes in several procedures in nuclear medicine. Some natural and sintetic drugs are capable to interfere on the labeling of blood constituents with 99mTc, on the morphology of red blood cells (RBC) and on the biodistribution of radiobiocomplexes. The aim of this study was evaluate the effect of an extract of Passiflora edulis f. flavicarpa on the labeling of blood constituints with 99mTc, on the morphology of RBC and on the biodistribution of the radiopharmaceutical sodium perthecnetate in Wistar rats. On the in vitro studies the Passiflora edulis f. flavicarpa decreased significantly (p<0.05) the %ATI on plasma proteins and on the in vitro morhology of RBC, the passion fruit peel flour altered the shape and the perimeter/área ratio. On the in vivo estudies the extract did not altered the %ATI in blood constituents, and did not altered the shape of RBC. Although, on the biodistribution of the radiobiocomplex sodium perthecnetate (Na99mTcO4) this extract decreased significantly (p<0.05) the uptake in duodenum, spleen, pâncreas and blood, and increased the uptake in stomach. It can be suggested that the effects presented by this extract could be a result of some substances contained in this extract that could alter the binding of 99mTc to plasma proteins, the morphology of RBC and the biodistribution of the radiobiocomplex sodium perthecnetate. This study was multidisciplinary experimental research. It was developed with the contribution of different Departments and Services of the Hospital Universitário Pedro Ernesto of the Universidade Estadual do Rio de Janeiro

Pendimethalin aplicado à casca de arroz e serragem para o controle de plantas daninhas em Ixora chinensis Lam.

A aplicação de herbicidas residuais à coberturas mortas pode aumentar a eficiência desses materiais no manejo da comunidade infestante. Objetivou-se, com este trabalho, avaliar a possibilidade de aplicação do pendimethalin à casca de arroz e à serragem para o controle de plantas daninhas em Ixora chinensis. Dois experimentos foram conduzidos aplicando-se o pendimethalin às coberturas mortas através de embebição e pulverização do herbicida, variando-se também a quantidade de cobertura utilizada. As espécies de plantas daninhas que ocorreram com maior frequência foram Alternanthera tenella, Blainvillea rhomboidea, Cenchrus echinatus e Commelina benghalensis. Há possibilidade de aplicação do herbicida pendimethalin à palha de arroz ou à serragem para controle de plantas daninhas em I. chinensis, principalmente quando ocorrem chuvas regulares e bem distribuídas. Há evidências de que a embebição da cobertura morta no herbicida seja um pouco mais eficiente no controle das plantas daninhas que a sua pulverização sobre a cobertura. Possivelmente, a quantidade de cobertura morta utilizada influencia na eficiência de controle, apesar deste fato não ter ficado claro neste trabalho.

Períodos de interferência das plantas daninhas em algodoeiro de fibra colorida ‘BRS Safira’

This study aimed to determine the late-season presence of weeds in reddish brown cotton (cultivar BRS Safira) and the critical times for removing weeds. The experiment was carried out in the area of Empresa Brasileira de Pesquisa Agropecuária (EMBRAPA) in Missao Velha-CE, Brazil, located at 7 degrees 42'07" S latitude and 39 degrees 24'18" WGr. longitude, during the 2007/2008 season. The treatments consisted of two control groups: weed-free crop during the initial period after crop emergency, and crop kept with weeds during initial period after plant emergency. Both consisted, 0; 20; 40; 60; 80 e 120 days after crop emergency (DAE), the weed community was evaluated by two phytosociological indices (relative dominance and relative importance). Regression analysis was performed as the model of sigmoidal Boltzman, using data from productivity separately within each type of competition, to identify the critical periods of competition, considering 2; 5 and 10% reduction in yield. The community of weeds was composed by 21 species, standing out among them: Richardia grandiflora, Amaranthus deflexus, Eleusine indica, Merremia aegyptia, Eragrotis pilosa, Cenchrus echinatus and Waltheria indica. Considering 2; 5 and 10% reduction in yield fiber as acceptable, the critical period before weed interference were, respectively, 8; 14 and 20 DAE. The critical period of weed interference, for those same levels of losses, were respectively, 100; 82 and 60 days.

Growth analysis of sweet pepper cultivated in coconut fiber in a greenhouse

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Uso do diluente água de coco em pó (ACP-103®) na conservação prolongada do sêmen do varrão: avaliação in vitro e in vivo

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Efeito da forma física da ração sobre a porosidade, espessura da casca, perda de água e eclodibilidade em ovos de perdiz (Rhynchotus rufescens)

O objetivo do presente estudo foi avaliar se a forma física da ração (farelada e peletizada) afeta a porosidade e espessura da casca, e porcentagem de perda de água e eclodibilidade de ovos de perdiz. Os ovos foram coletados logo após a postura e separados em diferentes intervalos de peso (35-45g, 46-50g, 51-55g, 56-60g e 61-70g), sendo 10 ovos/classe/ração. O número de poros das cascas foi avaliado nas regiões apical, equatorial e basal dos ovos. Utilizou-se um micrômetro digital para a mensuração da espessura das três regiões da casca dos ovos, a partir dos quais obteve-se a espessura média por ovo. Os ovos para avaliação da eclodibilidade e porcentagem de perda de água do ovo até a transferência para o nascedouro (16º dia) foram pesados, desinfectados, incubados (T=35,5ºC e UR= 70%) e transferidos no 16º dia de incubação para o nascedouro, onde foram mantidos até a eclosão. As análises estatísticas empregadas foram: Análise de Variância e de Correlação, e teste de Tukey 5%. Os dados mostraram que, em perdizes, o número de poros na casca pode variar com a região da casca, peso do ovo e a forma física da ração, e que a ingestão de ração peletizada promove um aumento na espessura da casca dos ovos sem alterar a eclodibilidade e a porcentagem de perda de água dos mesmos durante a incubação.

Crescimento e marcha de acúmulo de nutrientes em plantas de beterraba cultivadas em sistema hidropônico

A produção da beterraba tem alcançado grande destaque no cenário nacional, principalmente a produção de origem hidropônica, entretanto, as pesquisas são insipientes sobre a nutrição das plantas. Assim, objetivou-se neste trabalho avaliar o crescimento e a marcha de absorção de nutrientes pela beterraba cultivar Early Wonder, cultivado em sistema hidropônico. O delineamento experimental adotado foi em blocos casualizados com seis tratamentos constituídos pelas épocas de amostragem: 15; 25; 35; 45; 55 e 65 dias após o transplante (DAT) e cinco repetições. As mudas de beterraba foram transplantadas para estufa da UNESP Câmpus de Jaboticabal (em abril/2007), em vasos de 5 dm3, preenchido com substrato a base de fibra de coco, constantemente irrigadas com solução nutritiva (Hoagland e Arnon). Durante o período experimental, avaliou-se o desenvolvimento das plantas e a massa seca de folha, raiz tuberosa e raízes e o acúmulo de macro e de micronutrientes na planta. O acúmulo de matéria seca da raiz tuberosa da beterraba cultivar Early Wonder foi relativamente rápido, havendo predomínio da alocação de biomassa na raiz tuberosa (55%) comparado as folhas (43%) e as raízes (2%). As maiores exigências nutricionais da beterraba foram de K, N e P para os macronutrientes e de Mn, Zn e Fe para os micronutrientes. A absorção de nitrogênio, potássio e manganês pela beterraba é mais rápida, sendo alta a partir dos 15 dias do transplantio.