A systems methodology for analysing and simulating manufacturing systems

The Systems Engineering Group (SEG) at De Montfort University are developing the Boardman Soft Systems Methodology (BSSM) which allows complex human systems to be modelled, this work builds upon Checkland's Soft Systems Methodology (1981). The BSSM has been applied to the modelling of the systems engineering process as used in design and manufacturing companies. The BSSM is used to solicit information from a company and this data is then transformed into systemic diagrams (systemigrams). These systemigrams are posited to be accurate and concise representations of the system which has been modelled. This paper describes the collaboration between SEG and a manufacturing company (MC) in Leicester, England. The purpose of this collaboration was twofold. First, it was to create an objective view of the MC's processes, in the form of systemigrams. It was important to get this modelled by a source outside of the company, as it is difficult for people within a system being modelled to be unbiased. Secondly, it allowed a series of systemigrams to be produced which can then be subjected to simulation, for the purpose of aiding risk management decisions and to reduce the project cycle time

A detailed design study of leaching and ancillary processes in the hydrometallurgical extraction of iron from iron bearing feedstocks

A systematic survey of the possible methods of chemical extraction of iron by chloride formation has been presented and supported by a comparable study of :feedstocks, products and markets. The generation and evaluation of alternative processes was carried out by the technique of morphological analysis vihich was exploited by way of a computer program. The final choice was related to technical feasibility and economic viability, particularly capital cost requirements and developments were made in an estimating procedure for hydrometallurgjcal processes which have general applications. The systematic exploration included the compilation of relevant data, and this indicated a need.to investigate precipitative hydrolysis or aqueous ferric chloride. Arising from this study, two novel hydrometallurgical processes for manufacturing iron powder are proposed and experimental work was undertaken in the following .areas to demonstrate feasibility and obtain basic data for design purposes: (1) Precipitative hydrolysis of aqueous ferric chloride. (2) Gaseous chloridation of metallic iron, and oxidation of resultant ferrous chloride. (3) Reduction of gaseous ferric chloride with hydrogen. (4) Aqueous acid leaching of low grade iron ore. (5) Aqueous acid leaching of metallic iron. The experimentation was supported by theoretical analyses dealing with: (1) Thermodynamics of hydrolysis. (2) Kinetics of ore leaching. (3) Kinetics of metallic iron leaching. (4) Crystallisation of ferrous chloride. (5) Oxidation of anhydrous ferrous chloride. (6) Reduction of ferric chloride. Conceptual designs are suggested fbr both the processes mentioned. These draw attention to areas where further work is necessary, which are listed. Economic analyses have been performed which isolate significant cost areas, und indicate total production costs. Comparisons are mode with previous and analogous proposals for the production of iron powder.

Profit sharing in a manufacturing plant in a developing country : communication and organisational dynamics

The adaptation of profit sharing creates a fundamental change in employee compensation by making a portion of total compensation directly dependent upon the total profits of the firm and the performance of the employee. The major goal of this study is to test for and measure the impact of the independent variable, a profit sharing plan implemented at Shahvand Industrial Company, upon communication behaviour, communication outcomes, and organisational outcomes as dependent variables. A quasi-experimental non-equivalent control group design with pre and posttest was the research design used to test the effects of profit sharing participation on permanent-part-time operative employees implemented by SIC. Several conclusions were reached as a result of the statistical analysis of the data collected in this study. Overall, few of the hypothesised effects of profit sharing participation appeared to have been realised according to the empirical results of this study. The finding that certain communication behaviours were more favourable for profit sharing participants than for non-participants support the general hypothesis of the integrated profit sharing model. The observed changes in communication behaviours indicate that information sharing and idea generation are important components of the profit sharing process. The results of this study did not reveal any changes in either communication or organisational outcomes. A significant finding of this study is that the implementation of profit sharing plans require a relatively long period of time. Patience is required to achieve high levels of success and management must make long-term commitment to profit sharing. Findings of this study should be interpreted with caution, taking into consideration that most of the previo.us researches on profit sharing have been conducted in Western European or American countries, while the current study was based on data collected from an organisation in a developing country. This implies that the findings reported in this thesis may not be comparable in certain respects to results derived from companies in major industrialised economies.

A configuration framework of manufacturing strategy paradigm in state owned enterprises within China's petrochemical industry:building context-embedded configurations for the paradigm of strategic manufacturing management from exploratory case studies

The role of the production system as a key determinant of competitive performance of business operations- has long been the subject of industrial organization research, even predating the .explicit conceptua1isation of manufacturing, strategy in the literature. Particular emergent production issues such as the globalisation of production, global supply chain management, management of integrated manufacturing and a growing e~busjness environment are expected to critically influence the overall competitive performance and therefore the strategic success of the organization. More than ever, there is a critical need to configure and improve production system and operations competence in a strategic way so as to contribute to the long-term competitiveness of the organization. In order to operate competitively and profitably, manufacturing companies, no matter how well managed, all need a long-term 'strategic direction' for the development of operations competence in order to consistently produce more market value with less cost towards a leadership position. As to the long-term competitiveness, it is more important to establish a dynamic 'strategic perspective' for continuous operational improvements in pursuit of this direction, as well as ongoing reviews of the direction in relation to the overall operating context. However, it also clear that the 'existing paradigm of manufacturing strategy development' is incapable of adequately responding to the increasing complexities and variations of contemporary business operations. This has been factually reflected as many manufacturing companies are finding that methodologies advocated in the existing paradigm for developing manufacturing strategy have very limited scale and scope for contextual contingency in empirical application. More importantly, there has also emerged a deficiency in the multidimensional and integrative profile from a theoretical perspective when operationalising the underlying concept of strategic manufacturing management established in the literature. The point of departure for this study was a recognition of such contextual and unitary limitations in the existing paradigm of manufacturing strategy development when applied to contemporary industrial organizations in general, and Chinese State Owned Enterprises (SOEs) in particular. As China gradually becomes integrated into the world economy, the relevance of Western management theory and its paradigm becomes a practical matter as much as a theoretical issue. Since China markedly differs from Western countries in terms of culture, society, and political and economic systems, it presents promising grounds to test and refine existing management theories and paradigms with greater contextual contingency and wider theoretical perspective. Under China's ongoing programmes of SOE reform, there has been an increased recognition that strategy development is the very essence of the management task for managers of manufacturing companies in the same way as it is for their counterparts in Western economies. However, the Western paradigm often displays a rather naive and unitary perspective of the nature of strategic management decision-making, one which largely overlooks context-embedded factors and social/political influences on the development of manufacturing strategy. This thesis studies the successful experiences of developing manufacturing strategy from five high-performing large-scale SOEs within China’s petrochemical industry. China’s petrochemical industry constitutes a basic heavy industrial sector, which has always been a strategic focus for reform and development by the Chinese government. Using a confirmation approach, the study has focused on exploring and conceptualising the empirical paradigm of manufacturing strategy development practiced by management. That is examining the ‘empirical specifics’ and surfacing the ‘managerial perceptions’ of content configuration, context of consideration, and process organization for developing a manufacturing strategy during the practice. The research investigation adopts a qualitative exploratory case study methodology with a semi-structural front-end research design. Data collection follows a longitudinal and multiple-case design and triangulates case evidence from sources including qualitative interviews, direct observation, and a search of documentations and archival records. Data analysis follows an investigative progression from a within-case preliminary interpretation of facts to a cross-case search for patterns through theoretical comparison and analytical generalization. The underlying conceptions in both the literature of manufacturing strategy and related studies in business strategy were used to develop theoretical framework and analytical templates applied during data collection and analysis. The thesis makes both empirical and theoretical contributions to our understanding of 'contemporary management paradigm of manufacturing strategy development'. First, it provides a valuable contextual contingency of the 'subject' using the business setting of China's SOEs in petrochemical industry. This has been unpacked into empirical configurations developed for its context of consideration, its content and process respectively. Of special note, a lean paradigm of business operations and production management discovered at case companies has significant implications as an emerging alternative for high-volume capital intensive state manufacturing in China. Second, it provides a multidimensional and integrative theoretical profile of the 'subject' based upon managerial perspectives conceptualised at case companies when operationalising manufacturing strategy. This has been unpacked into conceptual frameworks developed for its context of consideration, its content constructs, and its process patterns respectively. Notably, a synergies perspective towards the operating context, competitive priorities and competence development of business operations and production management has significant implications for implementing a lean manufacturing paradigm. As a whole, in so doing, the thesis established a theoretical platform for future refinement and development of context-specific methodologies for developing manufacturing strategy.

A Generic model for the design and analysis of production systems

This dissertation studies the process of operations systems design within the context of the manufacturing organization. Using the DRAMA (Design Routine for Adopting Modular Assembly) model as developed by a team from the IDOM Research Unit at Aston University as a starting point, the research employed empirically based fieldwork and a survey to investigate the process of production systems design and implementation within four UK manufacturing industries: electronics assembly, electrical engineering, mechanical engineering and carpet manufacturing. The intention was to validate the basic DRAMA model as a framework for research enquiry within the electronics industry, where the initial IDOM work was conducted, and then to test its generic applicability, further developing the model where appropriate, within the other industries selected. The thesis contains a review of production systems design theory and practice prior to presenting thirteen industrial case studies of production systems design from the four industry sectors. The results and analysis of the postal survey into production systems design are then presented. The strategic decisions of manufacturing and their relationship to production systems design, and the detailed process of production systems design and operation are then discussed. These analyses are used to develop the generic model of production systems design entitled DRAMA II (Decision Rules for Analysing Manufacturing Activities). The model contains three main constituent parts: the basic DRAMA model, the extended DRAMA II model showing the imperatives and relationships within the design process, and a benchmark generic approach for the design and analysis of each component in the design process. DRAMA II is primarily intended for use by researchers as an analytical framework of enquiry, but is also seen as having application for manufacturing practitioners.

The interaction between master production scheduling and detailed capacity requirements planning : closing the loop in manufacturing resource planning (MRPII) systems

The widespread implementation of Manufacturing Resource Planning (MRPII) systems in this country and abroad and the reported dissatisfaction with their use formed the initial basis of this piece of research which concentrates on the fundamental theory and design of the Closed Loop MRPII system itself. The dissertation concentrates on two key aspects namely; how Master Production Scheduling is carried out in differing business environments and how well the `closing of the loop' operates by checking the capcity requirements of the different levels of plans within an organisation. The main hypothesis which is tested is that in U.K. manufacturing industry, resource checks are either not being carried out satisfactorily or they are not being fed back to the appropriate plan in a timely fashion. The research methodology employed involved initial detailed investigations into Master Scheduling and capacity planning in eight diverse manufacturing companies. This was followed by a nationwide survey of users in 349 companies, a survey of all the major suppliers of Production Management software in the U.K. and an analysis of the facilities offered by current software packages. The main conclusion which is drawn is that the hypothesis is proved in the majority of companies in that only just over 50% of companies are attempting Resource and Capacity Planning and only 20% are successfully feeding back CRP information to `close the loop'. Various causative factors are put forward and remedies are suggested.

The impact of NC machinery upon manufacturing industry

The changing face of industry due to the adoption of `New Technology' is briefly discussed, as are the corresponding structural changes in the workforce. The adoption of NC machinery is identified as one of the major innovations affecting the structure of industry. The development of NC machinery, and of relevant programming techniques are reviewed, and the problems arising from its initial sponsorship by the aerospace industry are highlighted. The process of its subsequent diffusion into industry is reviewed. Skill levels adopted for NC use in Britain and Germany are discussed, and analysed to create a structural pattern. These classifications of skill levels are then used to examine the organisational structures adopted by companies utilising NC machines. The greater use made of higher level shop floor skills by German companies is discussed. The results of two surveys of the use made of NC by companies in the North East of England are presented. Effective company organisation for NC use is described, and lack of foresight is shown to lead to vulnerability problems where skills can become concentrated in a few key people. This led to closure of a company in one instance. It is shown that small sub-contract companies have adopted a highly skilled shop floor workforce, and that they have survived in the present hostile economic environment, whilst companies who have used NC to de-skill the shop floor contracted dramatically in the same period. The lack of awareness of the potential for reviewing the product design in relation to the flexibility of NC, so leading to reductions in work in progress levels, is highlighted. Recommendations for skill structures appropriate to various sized companies and suitable training programs are presented to ensure that the full potential of NC machinery is achieved.

Computer aided manufacturing of geometric models

As systems for computer-aided-design and production of mechanical parts have developed, there has arisen a need for techniques for the comprehensive description of the desired part, including its 3-D shape. The creation and manipulation of shapes is generally known as geometric modelling. It is desirable that links be established between geometric modellers and machining programs. Currently, unbounded APT and some bounded geometry systems are being widely used in manufacturing industry for machining operations such as: milling, drilling, boring and turning, applied mainly to engineering parts. APT systems, however, are presently only linked to wire-frame drafting systems. The combination of a geometric modeller and APT will provide a powerful manufacturing system for industry from the initial design right through part manufacture using NC machines. This thesis describes a recently developed interface (ROMAPT) between a bounded geometry modeller (ROMULUS) and an unbounded NC processor (APT). A new set of theoretical functions and practical algorithms for the computer aided manufacturing of 3D solid geometric model has been investigated. This work has led to the development of a sophisticated computer program, ROMAPT, which provides a new link between CAD (in form of a goemetric modeller ROMULUS) and CAM (in form of the APT NC system). ROMAPT has been used to machine some engineering prototypes successfully both in soft foam material and aluminium. It has been demonstrated above that the theory and algorithms developed by the author for the development of computer aided manufacturing of 3D solid modelling are both valid and applicable. ROMAPT allows the full potential of a solid geometric modeller (ROMULUS) to be further exploited for NC applications without requiring major investment in new NC processor. ROMAPT supports output in APT-AC, APT4 and the CAM-I SSRI NC languages.

Computer integrated manufacturing control

Many manufacturing companies have long endured the problems associated with the presence of `islands of automation'. Due to rapid computerisation, `islands' such as Computer-Aided Design (CAD), Computer-Aided Manufacturing (CAM), Flexible Manufacturing Systems (FMS) and Material Requirement Planning (MRP), have emerged, and with a lack of co-ordination, often lead to inefficient performance of the overall system. The main objective of Computer-Integrated Manufacturing (CIM) technology is to form a cohesive network between these islands. Unfortunately, a commonly used approach - the centralised system approach, has imposed major technical constraints and design complication on development strategies. As a consequence, small companies have experienced difficulties in participating in CIM technology. The research described in this thesis has aimed to examine alternative approaches to CIM system design. Through research and experimentation, the cellular system approach, which has existed in the form of manufacturing layouts, has been found to simplify the complexity of an integrated manufacturing system, leading to better control and far higher system flexibility. Based on the cellular principle, some central management functions have also been distributed to smaller cells within the system. This concept is known, specifically, as distributed planning and control. Through the development of an embryo cellular CIM system, the influence of both the cellular principle and the distribution methodology have been evaluated. Based on the evidence obtained, it has been concluded that distributed planning and control methodology can greatly enhance cellular features within an integrated system. Both the cellular system approach and the distributed control concept will therefore make significant contributions to the design of future CIM systems, particularly systems designed with respect to small company requirements.

Computer integrated manufacturing (CIM) and the principle of business control

In response to the increasing international competitiveness, many manufacturing businesses are rethinking their management strategies and philosophies towards achieving a computer integrated environment. The explosive growth in Advanced Manufacturing Technology (AMI) has resulted in the formation of functional "Islands of Automation" such as Computer Aided Design (CAD), Computer Aided Manufacturing (CAM), Computer Aided Process Planning (CAPP) and Manufacturing Resources Planning (MRPII). This has resulted in an environment which has focussed areas of excellence and poor overall efficiency, co-ordination and control. The main role of Computer Integrated Manufacturing (CIM) is to integrate these islands of automation and develop a totally integrated and controlled environment. However, the various perceptions of CIM, although developing, remain focussed on a very narrow integration scope and have consequently resulted in mere linked islands of automation with little improvement in overall co-ordination and control. This thesis, that is the research described within, develops and examines a more holistic view of CIM, which is based on the integration of various business elements. One particular business element, namely control, has been shown to have a multi-facetted and underpinning relationship with the CIM philosophy. This relationship impacts various CIM system design aspects including the CIM business analysis and modelling technique, the specification of systems integration requirements, the CIM system architectural form and the degree of business redesign. The research findings show that fundamental changes to CIM system design are required; these are incorporated in a generic CIM design methodology. The affect and influence of this holistic view of CIM on a manufacturing business has been evaluated through various industrial case study applications. Based on the evidence obtained, it has been concluded that this holistic, control based approach to CIM can provide a greatly improved means of achieving a totally integrated and controlled business environment. This generic CIM methodology will therefore make a significant contribution to the planning, modelling, design and development of future CIM systems.

Some aspects of system design for production management in the rolling-mill industry

Case studies in copper-alloy rolling mill companies showed that existing planning systems suffer from numerous shortcomings. Where computerised systems are in use, these tend to simply emulate older manual systems and still rely heavily on modification by experienced planners on the shopfloor. As the size and number of orders increase, the task of process planners, while seeking to optimise the manufacturing objectives and keep within the production constraints, becomes extremely complicated because of the number of options for mixing or splitting the orders into batches. This thesis develops a modular approach to computerisation of the production management and planning functions. The full functional specification of each module is discussed, together with practical problems associated with their phased implementation. By adapting the Distributed Bill of Material concept from Material Requirements Planning (MRP) philosophy, the production routes generated by the planning system are broken down to identify the rolling stages required. Then to optimise the use of material at each rolling stage, the system generates an optimal cutting pattern using a new algorithm that produces practical solutions to the cutting stock problem. It is shown that the proposed system can be accommodated on a micro-computer, which brings it into the reach of typical companies in the copper-alloy rolling industry, where profit margins are traditionally low and the cost of widespread use of mainframe computers would be prohibitive.

Aspects of design for a spare parts provisioning system

This thesis describes an investigation by the author into the spares operation of compare BroomWade Ltd. Whilst the complete system, including the warehousing and distribution functions, was investigated, the thesis concentrates on the provisioning aspect of the spares supply problem. Analysis of the historical data showed the presence of significant fluctuations in all the measures of system performance. Two Industrial Dynamics simulation models were developed to study this phenomena. The models showed that any fluctuation in end customer demand would be amplified as it passed through the distributor and warehouse stock control systems. The evidence from the historical data available supported this view of the system's operation. The models were utilised to determine which parts of the total system could be expected to exert a critical influence on its performance. The lead time parameters of the supply sector were found to be critical and further study showed that the manner in which the lead time changed with work in progress levels was also an important factor. The problem therefore resolved into the design of a spares manufacturing system. Which exhibited the appropriate dynamic performance characteristics. The gross level of entity presentation, inherent in the Industrial Dynamics methodology, was found to limit the value of these models in the development of detail design proposals. Accordingly, an interacting job shop simulation package was developed to allow detailed evaluation of organisational factors on the performance characteristics of a manufacturing system. The package was used to develop a design for a pilot spares production unit. The need for a manufacturing system to perform successfully under conditions of fluctuating demand is not limited to the spares field. Thus, although the spares exercise provides an example of the approach, the concepts and techniques developed can be considered to have broad application throughout batch manufacturing industry.

Computer aided design and manufacture of form-rolls

Cold roll forming of thin-walled sections is a very useful process in the sheet metal industry. However, the conventional method for the design and manufacture of form-rolls, the special tooling used in the cold roll forming process, is a very time consuming and skill demanding exercise. This thesis describes the establishment of a stand-alone minicomputer based CAD/CAM system for assisting the design and manufacture of form-rolls. The work was undertaken in collaboration with a leading manufacturer of thin-walled sections. A package of computer programs have been developed to provide computer aids for every aspect of work in form-roll design and manufacture. The programs have been successfully implemented, as an integrated CAD/CAM software system, on the ICL PERQ minicomputer with graphics facilities. Thus, the developed CAD/CAM system is a single-user workstation, with software facilities to help the user to perform the conventional roll design activities including the design of the finished section, the flower pattern, and the form-rolls. A roll editor program can then be used to modify, if required, the computer generated roll profiles. As far as manufacturing is concerned, a special-purpose roll machining program and postprocessor can be used in conjunction to generate the NC control part-programs for the production of form-rolls by NC turning. Graphics facilities have been incorporated into the CAD/CAM software programs to display drawings interactively on the computer screen throughout all stages of execution of the CAD/CAM software. It has been found that computerisation can shorten the lead time in all activities dealing with the design and manufacture of form-rolls, and small or medium size manufacturing companies can gain benefits from the CAD/CM! technology by developing, according to its own specification, a tailor-made CAD/CAM software system on a low cost minicomputer.

Manufacturing organisation in developing countries with particular reference to Iraq

Industrially developed countries are able to absorb modern techniques of science and technology quite readily; this is not the case for less-developed countries. Attempts made by developing countries have been ineffective due to factors not readily admitted. This thesis highlights the areas that need to be developed by under-developed countries, and covers economic, scientific and technological, and social aspects as well as technology transfer. Economic areas considered acknowledge that within any one country there should be proper procedures for planning economic and industrial projects (plant design) supported by efficient economic development strategy. Scientific and technological factors considered include the major areas that need to be developed in order to produce and/or deal with scientific and technological issues for the interest of the national development. Technology transfer areas considered include the necessity of building up a national body (system) responsible for dealing with activities and tasks of transferring foreign-made technology so that it can be employed effectively within the environment of the country. Social factors considered include the need to develop human resources which can be employed efficiently into the whole process of development, and particularly for the above proposed systems. Education and training are the major elements that ought to be tackled to produce skilled manpower and to overcome the social and cultural values and traditions that are inherited by the society. This thesis highlights the above areas in an attempt to plan and organise the development of science and technology, and their implementation into the development as a whole. Whilst recognising the problems of creating this sort of development in developing countries, the author considers the benefits to be obtained are much greater in the long run.