Digital microfluidics on paper

This thesis is one of the first reports of digital microfluidics on paper and the first in which the chip’s circuit was screen printed unto the paper. The use of the screen printing technique, being a low cost and fast method for electrodes deposition, makes the all chip processing much more aligned with the low cost choice of paper as a substrate. Functioning chips were developed that were capable of working at as low as 50 V, performing all the digital microfluidics operations: movement, dispensing, merging and splitting of the droplets. Silver ink electrodes were screen printed unto paper substrates, covered by Parylene-C (through vapor deposition) as dielectric and Teflon AF 1600 (through spin coating) as hydrophobic layer. The morphology of different paper substrates, silver inks (with different annealing conditions) and Parylene deposition conditions were studied by optical microscopy, AFM, SEM and 3D profilometry. Resolution tests for the printing process and electrical characterization of the silver electrodes were also made. As a showcase of the applications potential of these chips as a biosensing device, a colorimetric peroxidase detection test was successfully done on chip, using 200 nL to 350 nL droplets dispensed from 1 μL drops.

Fungal communities in archives: assessment strategies and impact on paper conservation and human health

The main results presented in this PhD Dissertation have been published in interna-tional journals included in the Science Citation Index (SCI)

Valorization of agroindustrial waste

The main objective of this work is the valorization of residues from agro-industry giving them an added value. The valorization was performed by using a "green" and sustainable solvent - supercritical fluid, in this case carbon dioxide. Two residues and one biomass were used to produce two different final products, thereby emphasizing the versatility of the waste recovery - spent coffee grounds and microalgae Chlorella protothecoides to produce biodiesel, and tomato pomace to extract carotenoids. In the first part of this work it was demonstrated the possibility to obtain a conversion of coffee spent grounds oil into biodiesel, through an enzymatic transesterification reaction, of 98.01% with the following operating conditions: molar ratio oil:methanol 1:24, residence time 0.8 min, pressure 25 MPa, temperature 313,15K. In this first phase, it was also used the microalgae Chlorella protothecoides, a biomass, to produce biodiesel and favorable results were obtained with this green process compared with a traditional process - basic catalysis / acid. In the second part of this work, by an extraction with supercritical CO2 it was obtained 3.38% oil from tomato pomace under the following conditions: pressure 35.1 MPa, temperature 313,15K. It was found that this oil contains various carotenoids: β-carotene, lutein and lycopene. The latter is present in larger amount.

Epidemiology of hepatitis B virus infection among recyclable waste collectors in central Brazil

Introduction: The collection of recyclable waste materials is a widespread activity among the urban poor. Today, this occupation attracts an increasingly large number of individuals. Despite its economic and environmental importance, this activity is associated with unsafe and unhealthy working conditions. The aim of this study was to investigate the seroepidemiological profile of hepatitis B virus (HBV) infection in a population of recyclable waste collectors in central Brazil. Methods: Recyclable waste collectors from all 15 recycling cooperatives in Goiânia City were invited to participate in the study. The participants (n = 431) were interviewed and screened for hepatitis B surface antigen (HBsAg) and antibodies against HBsAg (anti-HBs) and hepatitis B core antigen (anti-HBc) by enzyme-linked immunosorbent assay (ELISA). HBsAg- and anti-HBc-positive samples were tested for HBV DNA and genotyped. Results: The overall prevalence of HBV infection (HBsAg- and/or anti-HBc-positive) was 12.8%. An age over 40 years and illicit drug use were associated with HBV infection. HBV DNA was detected in 2/3 HBsAg-positive samples and in 1/52 anti-HBc-positive/HBsAg-negative samples (an occult HBV infection rate of 1.9%), in which the genotypes/subgenotypes A/A1, D/D3 and F/F2 were identified. Only 12.3% of the recyclable waste collectors had serological evidence of previous HBV vaccination. Conclusions: These findings highlight the vulnerability of recyclable waste collectors to HBV infection and reinforce the importance of public health policies that address the health and safety of this socially vulnerable population.

Questionário de satisfação do utente e do profissional : impacto num laboratório de análises clínicas

RESUMO: Temos assistido a uma evolução impressionante nos laboratórios de análises clínicas, os quais precisam de prestar um serviço de excelência a custos cada vez mais competitivos. Nos laboratórios os sistemas de gestão da qualidade têm uma importância significativa nesta evolução, fundamentalmente pela procura da melhoria continua, que ocorre não só ao nível de processos e técnicas, mas também na qualificação dos diferentes intervenientes. Um dos problemas fundamentais da gestão e um laboratório é a eliminação de desperdícios e erros criando benefícios, conceito base na filosofia LeanThinking isto é “pensamento magro”, pelo que é essencial conseguir monitorizar funções críticas sistematicamente. Esta monitorização, num laboratório cada vez mais focalizado no utente, pode ser efetuada através de sistemas e tecnologias de informação, sendo possível contabilizar número de utentes, horas de maior afluência, tempo médio de permanência na sala de espera, tempo médio para entrega de análises, resultados entregues fora da data prevista, entre outros dados de apoio à decisão. Devem igualmente ser analisadas as reclamações, bem como a satisfação dos utentes quer através do feedback que é transmitido aos funcionários, quer através de questionários de satisfação. Usou-se principalmente dois modelos: um proposto pelo Índice Europeu de Satisfação do Consumidor (ECSI) e o outro de Estrutura Comum de Avaliação (CAF). Introduziram-se igualmente dois questionários: um apresentado em formato digital num posto de colheitas, através de um quiosque eletrónico, e um outro na página da internet do laboratório, ambos como alternativa ao questionário em papel já existente, tendo-se analisado os dados, e retirado as devidas conclusões. Propôs-se e desenvolveu-se um questionário para colaboradores cuja intenção foi a de fornecer dados úteis de apoio à decisão, face à importância dos funcionários na interação com os clientes e na garantia da qualidade ao longo de todo o processo. Avaliaram-se globalmente os resultados sem que tenha sido possível apresentá-los por política interna da empresa, bem como se comentou de forma empírica alguns benefícios deste questionário. Os principais objetivos deste trabalho foram, implementar questionários de satisfação eletrónicos e analisar os resultados obtidos, comparando-os com o estudo ECSI, de forma a acentuar a importância da análise em simultâneo de dois fatores: a motivação profissional e a satisfação do cliente, com o intuito de melhorar os sistemas de apoio à decisão. ------------------------ ABSTRACT: We have witnessed an impressive development in clinical analysis laboratories, which have to provide excellent service at increasingly competitive costs, quality management systems have a significant importance in this evolution, mainly by demanding continuous improvement, which does not occur only in terms of processes and techniques, but also in the qualification of the various stakeholders. One key problem of managing a laboratory is the elimination of waste and errors, creating benefits, concept based on Lean Thinking philosophy, therefore it is essential be able to monitor critical tasks systematically. This monitoring, in an increasingly focused on the user laboratory can be accomplished through information systems and technologies, through which it is possible to account the number of clients, peak times, average length of waiting room stay, average time for delivery analysis, delivered results out of the expected date, among other data that contribute to support decisions, however it is also decisive to analyzed complaint sand satisfaction of users through employees feedback but mainly through satisfaction questionnaires that provides accurate results. We use mainly two models one proposed by the European Index of Consumer Satisfaction (ECSI), directed to the client, and the Common Assessment Framework (CAF), used both in the client as the employees surveys. Introduced two questionnaires in a digital format, one in the central laboratory collect center, through an electronic kiosk and another on the laboratory web page, both as an alternative to survey paper currently used, we analyzed the results, and withdrew the conclusions. It was proposed and developed a questionnaire for employees whose intention would be to provide useful data to decision support, given the importance of employees in customer interaction and quality assurance throughout the whole clinical process, it was evaluated in a general way because it was not possible to show the results, however commented an empirical way some benefits of this questionnaire. The main goals of this study were to implement electronic questionnaires and analyze the results, comparing them with the ECSI, in order to emphasize the importance of analyzing simultaneously professional motivation with customer satisfaction, in order to improve decision support systems.

Weight concerns scale applied to college students : Comparison between pencil-and-paper and online formats

Online data collection is becoming increasingly common and has some advantages compared to traditional paper-and-pencil formats, such as reducing loss of data, increasing participants' privacy, and decreasing the effect of social desirability. However, the validity and reliability of this administration format must be established before results can be considered acceptable. The aim of this study was to evaluate the validity, reliability, and equivalence of paper-and-pencil and online versions of the Weight Concerns Scale (WCS) when applied to Brazilian university students. A crossover design was used, and the Portuguese version of the WCS (in both paper-and-pencil and online formats) was completed by 100 college students. The results indicated adequate fit in both formats. The simultaneous fit of data for both groups was excellent, with strong invariance between models. Adequate convergent validity, internal consistency, and mean score equivalence of the WCS in both formats were observed. Thus, the WCS presented adequate reliability and validity in both administration formats, with equivalence/stability between answers.

Development of paper transistor with memory effect

This work will discuss the use of different paper membranes as both the substrate and dielectric for field-effect memory transistors. Three different nanofibrillated cellulose membranes (NFC) were used as the dielectric layer of the memory transistors (NFC), one with no additives, one with an added polymer PAE and one with added HCl. Gallium indium zinc oxide (GIZO) was used as the device’s semiconductor and gallium aluminium zinc oxide (GAZO) was used as the gate electrode. Fourier transform infrared spectroscopy (FTIR) was used to access the water content of the paper membranes before and after vacuum. It was found that the devices recovered their water too quickly for a difference to be noticeable in FTIR. The transistor’s electrical performance tests yielded a maximum ION/IOFF ratio of around 3,52x105 and a maximum subthreshold swing of 0,804 V/decade. The retention time of the dielectric charge that grants the transistor its memory capabilities was accessed by the measurement of the drain current periodically during 144 days. During this period the mean drain current did not lower, leaving the retention time of the device indeterminate. These results were compared with similar devices revealing these devices to be at the top tier of the state-of-the-art.

Consumer satisfaction with water, wastewater and waste services in Portugal

While the concept of consumer satisfaction is a central topic in modern marketing theory and practice, citizens' satisfaction with public services, and especially water and waste services, is a eld that still remains empirically rather unexplored. The following study aims to contribute to this area by analysing the determinants of user satisfaction in the water, wastewater and waste sector in Portugal, using a unique survey of 1070 consumers undertaken by the Portuguese Water and Waste Regulator ERSAR. I perform an analysis of the relation between overall service satisfaction and attributespeci c service satisfaction with an ordered logit model. I then explore if subjective consumer satisfaction can be re ected by ERSAR's technical performance indicators. The results suggest that overall consumer satisfaction is driven by consumer's satisfaction with speci c service aspects but unrelated to socioeconomic and demographic characteristics. Furthermore, I show that there is no monotonic association between ERSAR's technical performance indicators and consumers' levels of satisfaction.

A multi-criteria decision support system for a routing problem in waste collection

Autor proof

A decision support system for a waste collection vehicle routing problem

The selective collection of municipal solid waste for recycling is a very complex and expensive process, where a major issue is to perform cost-efficient waste collection routes. Despite the abundance of commercially available software for fleet management, they often lack the capability to deal properly with sequencing problems and dynamic revision of plans and schedules during process execution. Our approach to achieve better solutions for the waste collection process is to model it as a vehicle routing problem, more specifically as a team orienteering problem where capacity constraints on the vehicles are considered, as well as time windows for the waste collection points and for the vehicles. The final model is called capacitated team orienteering problem with double time windows (CTOPdTW).We developed a genetic algorithm to solve routing problems in waste collection modelled as a CTOPdTW. The results achieved suggest possible reductions of logistic costs in selective waste collection.

Toxicity measurement techniques for building materials with wastes

The innovative Horizon 2020 program sponsored by the European Union (EU) aims to promote and develop processes of waste integration in construction materials. However, several potential health hazards caused by building materials have been identified and, there-fore, there is an ongoing need to develop new recycling methods for hazardous wastes and effi-cient barriers in order to prevent toxic releases from the new construction solutions with wastes. This paper presents an overview that focus on two main aspects: the identification of the health risks related to radioactivity and heavy metals present in building materials and identification of these toxic substances in new construction solutions that contain recycled wastes. Different waste materials were selected and distinct methodologies of toxicity evaluation are presented to analyse the potential hazardous, the feasibility of using those wastes and the achievement of op-timal construction solutions involving wastes.

Recycled asphalt mixtures produced with high percentage of different waste materials

The use of sustainable solutions in construction is not just an option, but is increasingly becoming a need of the Society. Thus, nowadays the recycling of waste materials is a growing technology that needs to be continuously improved, namely by researching new solutions for waste valorisation and by increasing the amount of wastes reused. In the paving industry, the reuse of reclaimed asphalt (RA) is becoming common practice, but needs further research work. Thus, this study aims to increase the incorporation of RA and other waste materials in the production of recycled asphalt mixtures in order to improve their mechanical, environmental and economic performance. Recycled mixtures with 50% RA were analysed in this study, including: i) RA selection, preparation and characterization; ii) incorporation of other waste materials as binder additives or modifiers, like used motor oil (UMO) and waste high density polyethylene (HDPE); iii) production of different mixtures (without additives; with UMO; with UMO and HDPE) and comparison of their performance in order to assess the main advantages of each solution. With this study it was concluded that up to 7.5 % of UMO and 4.0 % of HDPE can be used in a new modified binder for asphalt mixtures with 50 % of RA, which have excellent properties concerning the rutting with WTS = 0.02 mm/103 cycles, the fatigue resistance with ε6 = 160.4, and water sensitivity with an ITSR of 81.9 %.

The encore project: sustainable solutions for cementitious materials

Since concrete is the most widely utilized construction material, several solutions are currently being developed and investigated for enhancing the sustainability of cementitious materials. One of these solutions is based on producing Recycled Concrete Aggregates (RCA) from existing concrete members resulting by either industrial processes or demolitions of existing structures as a whole. Moreover, waste resulting from industrial processes other than the building construction (i.e., tire recycling, production of steel, powders resulting from other depuration processes) are also being considered as possible low-impact constituents for producing structural concrete and Fiber-Reinforced Cementitious Composites (FRCC). Furthermore, the use of natural fibers is another option for producing environmentally-friendly and cost-effective materials, depending on the local availability of raw materials. To promote the use of concretes partially composed of recycled constituents, their influence on the mechanical and durability performance of these concretes have to be deeply investigated and correlated. This was the main goal of the EnCoRe Project (www.encore-fp7.unisa.it), a EU-funded initiative, whose activities and main findings are summarized in this paper.

Workplace ergonomics in lean production environments: A literature review

BACKGROUND: Lean Production Systems (LPS) have become very popular among manufacturing industries, services and large commercial areas. A LPS must develop and consider a set of work features to bring compatibility with workplace ergonomics, namely at a muscular, cognitive and emotional demands level. OBJECTIVE: Identify the most relevant impacts of the adoption of LPS from the ergonomics point of view and summarizes some possible drawbacks for workplace ergonomics due to a flawed application of the LPS. The impacts identified are focused in four dimensions: work pace, intensity and load; worker motivation, satisfaction and stress; autonomy and participation; and health outcome. This paper also discusses the influence that the work organization model has on workplace ergonomics and on the waste elimination previewed by LPS. METHODS: Literature review focused LPS and its impact on occupational ergonomics conditions, as well as on the Health and Safety of workers. The main focus of this research is on LPS implementations in industrial environments and mainly in manufacturing industry workplaces. This is followed by a discussion including the authors’ experience (and previous research). RESULTS: From the reviewed literature it seems that there is no consensus on how Lean principles affect the workplace ergonomics since most authors found positive (advantages) and negative (disadvantages) impacts. CONCLUSIONS: The negative impacts or disadvantages of LPS implementations reviewed may result from the misunderstanding of the Lean principles. Possibly, they also happen due to partial Lean implementations (when only one or two tools were implemented) that may be effective in a specific work context but not suitable to all possible situations as the principles of LPS should not lead, by definition, to any of the reported drawbacks in terms of workplace ergonomics.

Evaluation of the performance of recycled textile fibres in the mechanical behaviour of a gypsum and cork composite material

Given the need for using more sustainable constructive solutions, an innovative composite material based on a combination of distinct industrial by-products is proposed aiming to reduce waste and energy consumption in the production of construction materials. The raw materials are thermal activated flue-gas desulphurization (FGD) gypsum, which acts as a binder, granulated cork as the aggregate and recycled textile fibres from used tyres intended to reinforce the material. This paper presents the results of the design of the composite mortar mixes, the characterization of the key physical properties (density, porosity and ultrasonic pulse velocity) and the mechanical validation based on uniaxial compressive tests and fracture energy tests. In the experimental campaign, the influence of the percentage of the raw materials in terms of gypsum mass, on the mechanical properties of the composite material was assessed. It was observed that the percentage of granulated cork decreases the compressive strength of the composite material but contributes to the increase in the compressive fracture energy. Besides, the recycled textile fibres play an important role in the mode I fracture process and in the fracture energy of the composite material, resulting in a considerable increase in the mode I fracture energy.