Improving the fire retardancy of extruded/coextruded wood-plastic composites

The main objective of this thesis is to study the impact of different mineral fillers and fire retardants on the reaction-to-fire properties of extruded/coextruded wood-plastic composites (WPCs). The impact of additives on the flammability properties of WPCs is studied by cone calorimetry. The studied properties are ignition time, peak heat release rate, total heat release, total smoke production, and mass loss rate. The effects of mineral fillers and fire retardants were found to vary with the type of additive, the type of additive combinations, the amount of additives, as well as the production method of the WPCs. The study shows that talc can be used to improve the properties of extruded WPCs. Especially ignition time, peak heat release rate and mass loss rate were found to be improved significantly by talc. The most significant improvement in the fire retardancy of coextruded WPCs was achieved in combinations of natural graphite and melamine. Ignition time, peak heat release rate and total smoke production were improved essentially. High increase in smoke production was found in samples where the amount of ammonium polyphosphate was 10% or higher. Coextrusion as a structural modification was found as a promising way to improve the flammability properties of composite materials in a cost-effective way.

First-principles study on electronic and structural properties of Cu(In/Ga)Se alloys for solar cells

Thin-film photovoltaic solar cells based on the Cu(In1−xGax)Se2 (CIGS) alloys have attracted more and more attention due to their large optical absorption coefficient, long term stability, low cost, and high efficiency. Modern theoretical studies of this material with first-principles calculations can provide accurate description of the electronic structure and yield results in close agreement with experimental values, but takes a large amount of calculation time. In this work, we use first-principles calculations based on the computationally affordable meta- generalized gradient approximation of the density-functional theory to investigate electronic and structural properties of the CIGS alloys. We report on the simulation of the lattice parameters and band gaps, as a function of chemical composition. The obtained results were found to be in a good agreement with the available experimental data.

New methods for controlling twin configurations and characterizing twin boundaries in 5M Ni-Mn-Ga for the development of applications

Traditional methods for studying the magnetic shape memory (MSM) alloys Ni-Mn-Ga include subjecting the entire sample to a uniform magnetic field or completely actuating the sample mechanically. These methods have produced significant results in characterizing the MSM effect, the properties of Ni-Mn-Ga and have pioneered the development of applications from this material. Twin boundaries and their configuration within a Ni-Mn-Ga sample are a key component in the magnetic shape memory effect. Applications that are developed require an understanding of twin boundary characteristics and, more importantly, the ability to predictably control them. Twins have such a critical role that the twinning stress of a Ni-Mn-Ga crystal is the defining characteristic that indicates its quality and significant research has been conducted to minimize this property. This dissertation reports a decrease in the twinning stress, predictably controlling the twin configuration and characterizing the dynamics of twin boundaries. A reduction of the twinning stress is demonstrated by the discovery of Type II twins within Ni-Mn-Ga which have as little as 10% of the twinning stress of traditional Type I twins. Furthermore, new methods of actuating a Ni-Mn-Ga element using localized unidirectional or bidirectional magnetic fields were developed that can predictably control the twin configuration in a localized area of a Ni-Mn-Ga element. This method of controlling the local twin configuration was used in the characterization of twin boundary dynamics. Using a localized magnetic pulse, the velocity and acceleration of a single twin boundary were measured to be 82.5 m/s and 2.9 × 107 m/s2, and the time needed for the twin boundary to nucleate and begin moving was less than 2.8 μs. Using a bidirectional magnetic field from a diametrically magnetized cylindrical magnet, a highly reproducible and controllable local twin configuration was created in a Ni-Mn-Ga element which is the fundamental pumping mechanism in the MSM micropump that has been co-invented and extensively characterized by the author.

Marks of Fire, Value and Faith. Swords with Ferrous Inlays in Finland during the Late Iron Age (ca. 700–1200 AD)

This study explores swords with ferrous inlays found in Finland and dating from the late Iron Age, ca. 700–1200 AD. These swords reflect profound changes not only in styles and fashion but also in the technology of hilts and blades. This study explores how many of these kinds of swords are known from Finland, how they were made and where, what their status was in Late Iron Age Finland, and where the Finnish finds stand in accordance with other areas of Europe. The various methods included measuring of the finds and statistics. The main method of revealing the inlaid marks was radiography due to its non-destructive nature. In cases where inlays were visible without radiography, their details were inspected via microscopy. To study the materials and manufacture of inlaid swords, a sample of them was metallographically analysed to determine the forging technologies and nature of used materials. Furthermore, the manufacture was also studied with experimental approaches. As a result, a catalogue of 151 swords with ferrous inlays was created. This number is relatively high compared with other European countries, although systematic studies have been conducted in only some countries. The inlaid motifs were classified into five distinct categories to help the classification. To summarize, almost every documented inlaid sword was unique in some respect including measurements, inlaid motifs and materials of blades and inlays. Technological variation was also present, some blades being poorer and some of higher quality in spite of the inlaid motifs. Misspelt inscriptions as well as letter-like marks were common in Finland and also in Scandinavia. Furthermore, the provenance of iron and steel used in some blades hints at Scandinavian ores. The above observations, along with the experimental results indicating the existence of multiple alternative techniques of inlaying, suggest that these swords were manufactured locally in Scandinavia, most likely in imitation of Continental European models. Inlaid swords were valued partly for their assumed functionality in combat, as evidenced by damage on some examined blades, or they were valued for their inlays, which could have had fashionable or symbolical meanings bound to local beliefs.

Development of a bacteriophage-based biopesticide for fire blight

Fire blight is an economically important disease of apples and pears that is caused by the bacterium Erwinia amylovora. Control of the disease depends on limiting primaly blosson1 infection in the spring, and rapidly removing infected tissue. The possibility of using phages to control E.amylovora populations has been suggested, but previous studies have. failed to show high treatment efficacies. This work describes the development of a phage-based biopesticide that controls E. amylovora populations under field conditions, and significantly reduces the incidence of fire blight. This work reports the first use ofPantoea agglomerans, a non-pathogenic relative ofE. amylovora, as a carrier for E. amylovora.phages. Its role is to support a replicating population of these phages on blossom surfaces during the period when the flowers are most susceptible to infection. Seven phages and one carrier isolate were selected for field trials from existing collections of 56 E. amylovora phages and 249 epiphytic orchard bacteria. Selection of the . /' phages and carrier was based on characteristics relevant to the production and field perfonnance of a biopesticide: host range, genetic diversity, growth under the conditions of large-scale production, and the ability to prevent E. amylovora from infecting pear blossoms. In planta assays showed that both the phages and the carrier make significant contributions to reducirig the development of fire blight symptoms in pear blossoms. Field-scale phage production and purification methods were developed based on the growth characteristics of the phages and bacteria in liquid culture, and on the survival of phages in various liquid media. Six of twelve phage-carrier biopesticide treatments caused statistically signiflcant reductions in disease incidence during orchard trials. Multiplex real-time PCR was used to simultaneously monitor the phage, carrier, and pathogen populations over the course of selected treatments. In all cases. the observed population dynamics of the biocontrol agents and the pathogen were consistent with the success or failure of each treatment to control disease incidence. In treatments exhibiting a significantly reduced incidel1ce of fire blight, the average blossom population ofE.amylovora had been reduced to pre-experiment epiphytic levels. In successful treatments the phages grew on the P. agglomerans carrier for 2 to 3 d after treatment application. The phages then grew preferentially on the pathogen, once it was introduced into this blossom ecosystem. The efficacy of the successful phage-based treatnlents was statistically similar to that of streptomycin, which is the most effective bactericide currently available for fire blight prevention. The in planta behaviour ofE. amylovora was compared to that ofErwinia pyrifoliae, a closely related species that causes fire blight-like synlptoms on pears in southeast Asia. Duplex real-time PCR was used to monitor the population dynamics of both species on single blossonls. E. amylovora exhibited a greater competitive fitness on Bartlett pear blossoms than E. pyrifoliae. The genome ofErwinia phage Ea21-4 was sequenced and annotated. Most of the 8-4.7 kB genome is substantially different from previously described sequences, though some regions are notably similar to Salmonella phage Felix 01 . Putative functions were assigned to approximately 30% of the predicted open reading frames based on amino acid sequence comparisons and N-terminal sequencing of structural proteins.

An analysis of the photoelectron and Rydberg states of formaldehyde /|nby Carol R. Lessard. -- 260 St. Catharines [Ont.] : Dept. of Chemistry, Brock University,

Although it is generally accepted that Rydberg orbitals are very large and diffuse, and that electron promotion to a Rydberg orbital is not too different from ionization of the molecule, analysis of the two types of transitions proves otherwise. The photoelectron spectrum of the 2B2 (n) ion has very little vibrational structure attached to the origin band; on the other hand, several of the Rydberg transitions which involve the promotion of the n(bZ) electron exhibit a great deal of vibrational activity. In particular, the members of the n=3 Rydberg\ series interact with and perturb each other through pseudo-Jahn-Teller vibronic coupling. The vacuum ultraviolet spectrum contains a number of features which are difficult to explain, and two unusually sharp bands can only be identified as representing some form of electron promotion in formaldehyde.

An application of cell-cluster theory to a rare gas crystal /|n[by] K. Westera. - 260 St. Catharines [Ont.] : Dept. of Physics, Brock University,

The Lennard-Jones Devonshire 1 (LJD) single particle theory for liquids is extended and applied to the anharmonic solid in a high temperature limit. The exact free energy for the crystal is expressed as a convergent series of terms involving larger and larger sets of contiguous particles called cell-clusters. The motions of all the particles within cell-clusters are correlated to each other and lead to non-trivial integrals of orders 3, 6, 9, ... 3N. For the first time the six dimensional integral has been calculated to high accuracy using a Lennard-Jones (6-12) pair interaction between nearest neighbours only for the f.c.c. lattice. The thermodynamic properties predicted by this model agree well with experimental results for solid Xenon.

A study of thermal decompositions of an allylic hydroperoxide /|nby Thomas A. McCarrick. -- 260 St. Catharines [Ont.] : Dept. of Chemistry, Brock University,

The thermal decomposition of 2,3-di~ethy l - J-hydr operox y- 1 - butene , p r epared f rol") singl e t oxygen, has been studied i n three solvents over the tempe r a ture r ange from 1500e to l o00e and t!1e i 111 t ial ~oncentrfttl nn r Ange from O. 01 M to 0.2 M. Analys i s of the kine tic data ind ica te s i nduced homolysis as the n ost probRble mode of d e composition, g iving rise to a 3/2 f S order dependence upon hy d.roperoxide concent :r8.tl on . Experimental activation e nergies for the decomposition were f ound to be between 29.5 kcsl./raole and 30.0 k cal./mole .• \,iith log A factors between 11 . 3 and 12.3. Product studies were conducted in R variety of solvents a s well as in the pr esence of a variety of free r adical initiators . Investigation of the kinetic ch a in length indicated a chain length of about fifty. A degenerat i ve chain branching mechanism 1s proposed which predicts the multi t ude of products which Rre observed e xperimentally as well as giving activation energies and log A factors si~il a r to those found experimentally .

Reduced local energy calculations on X¹Sigmaâ ½gHâ and 1¹S He /|nGerald F. Thomas. -- 260 St. Catharines [Ont.] : Dept. of Chemistry, Brock University,

The one-electron reduced local energy function, t ~ , is introduced and has the property < tL)=(~>. It is suggested that the accuracy of SL reflects the local accuracy of an approximate wavefunction. We establish that <~~>~ <~2,> and present a bound formula, E~ , which is such that where Ew is Weinstein's lower bound formula to the ground state. The nature of the bound is not guaranteed but for sufficiently accurate wavefunctions it will yield a lower bound. ,-+ 1'S I I Applications to X LW Hz. and ne are presented.

The crystal and molecular structure of thiamine hydroiodide /|nWilliam Edward Lee. -- 260 St. Catharines [Ont.] : Dept. of Chemistry, Brock University,

The x-ray crystal structure of thiamine hydroiodide,C1ZH18N40S12' has been determined. The unit cell parameters are a = 13.84 ± 0.03, o b = 7.44 ± 0.01, c = 20.24 ± 0.02 A, 8 = 120.52 ± 0.07°, space group P2/c, z = 4. A total of 1445 reflections having ,2 > 2o(F2), 26 < 40° were collected on a Picker four-circle diffractometer with MoKa radiation by the 26 scan technique. The structure was solved by the heavy atom method. The iodine and sulphur atoms were refined anisotropically; only the positional parameters were refined for the hydrogen atoms. Successive least squares cycles yielded an unweighted R factor of 0.054. The site of protonation of the pyrimidine ring is the nitrogen opposite the amino group. The overall structure conforms very closely to the structures of other related thiamine compounds. The bonding surrounding the iodine atoms is distorted tetrahedral. The iodine atoms make several contacts with surrounding atoms most of them at or near the van der Waal's distances A thiaminium tetrachlorocobaltate salt was produced whose molecular and crystal structure was j~dged to be isomorphous to thiaminium tetrachlorocadmate.

The diffusion of Co⠶溩 Zrâ â Tiâ â alloy /|nS. Kumar. -- 260 St Catharines [Ont.] : Dept. of Physics, Brock University,

The diffusion of Co60 in the body centered cubic beta phase of a ZrSOTi SO alloy has been studied at 900°, 1200°, and 1440°C. The results confirm earlier unpublished data obtained by Kidson17 • The temperature dependence of the diffusion coefficient is unusual and suggests that at least two and possibly three mechanisms may be operative Annealing of the specimen in the high B.C.C. region prior to the deposition of the tracer results in a large reduction in the diffusion coefficient. The possible significance of this effect is discussed in terms of rapid transport along dislocation network.