Heat pulse line-source method to determine thermal conductivity of consolidated rocks

An instrument designed to measure thermal conductivity of consolidated rocks, dry or saturated, using a transient method is presented. The instrument measures relative values of the thermal conductivity, and it needs calibration to obtain absolute values. The device can be used as heat pulse line source and as continuous heat line source. Two parameters to determine thermal conductivity are proposed: TMAX, in heat pulse line source, and SLOPE, in continuous heat line source. Its performance is better, and the operation simpler, in heat pulse line-source mode with a measuring time of 170 s and a reproducibility better than 2.5%. The sample preparation is very simple on both modes. The performance has been tested with a set of ten rocks with thermal conductivity values between 1.4 and 5.2 W m¿1 K¿1 which covers the usual range for consolidated rocks.

Fluid evolution at the Variscan front in the vicinity of the Aachen thrust

Quartz-carbonate-chlorite veins were studied in borehole samples of the RWTH-1 well in Aachen. Veins formed in Devonian rocks in the footwall of the Aachen thrust during Variscan deformation and associated fluid flow. Primary fluid inclusions indicate subsolvus unmixing of a homogenous H(2)O-CO(2)-CH(4)-(N(2))-Na-(K)-Cl fluid into a H(2)O-Na-(K)-Cl solution and a vapour-rich CO(2)-(H(2)O, CH(4), N(2)) fluid. The aqueous end-member composition resembles that of metamorphic fluids of the Variscan front zone with salinities ranging from 4 to 7% NaCl equiv. and maximum homogenisation temperatures of close to 400A degrees C. Pressure estimates indicate a burial depth between 4,500 and 8,000 m at geothermal gradients between 50 and 75A degrees C/26 MPa, but pressure decrease to sublithostatic conditions is also indicated, probably as a consequence of fracture opening during episodic seismic activity. A second fluid system, mainly preserved in pseudo-secondary and secondary fluid inclusions, is characterised by fluid temperatures between 200 and 250A degrees C and salinities of < 5% NaCl equiv. Bulk stable isotope analyses of fluids released from vein quartz, calcite, and dolomite by decrepitation yielded delta D(H2O) values from -89 to -113 aEuro degrees, delta(13)C(CH4) from -26.9 to -28.9aEuro degrees (VPDB) and delta(13)C(CO2) from -12.8 to -23.3aEuro degrees (VPDB). The low delta D and delta(13)C range of the fluids is considered to be due to interaction with cracked hydrocarbons. The second fluid influx caused partial isotope exchange and disequilibrium. It is envisaged that an initial short lived flux of hot metamorphic fluids expelled from the epizonal metamorphic domains of the Stavelot-Venn massif. The metamorphic fluid was focused along major thrust faults of the Variscan front zone such as the Aachen thrust. A second fluid influx was introduced from formation waters in the footwall of the Aachen thrust as a consequence of progressive deformation. Mixing of the cooler and lower salinity formation water with the hot metamorphic fluid during episodic fluid trapping resulted in an evolving range of physicochemical fluid inclusion characteristics.

Upper Triassic to Cretaceous radiolaria from Nicaragua and northern Costa Rica - The Mesquito composite oceanic terrane

We propose a new terrane subdivision of Nicaragua and Northern Costa Rica, based on Upper Triassic to Upper Cretaceous radiolarian biochronology of ribbon radiolarites, the newly studied Siuna Serpentinite Mélange, and published 40Ar/39Ar dating and geochemistry of mafic and ultramafic igneous rock units of the area. The new Mesquito Composite Oceanic Terrane (MCOT) comprises the southern half of the Chortis Block, that was assumed to be a continental fragment of N-America. The MCOT is defined by 4 corner localities characterized by ultramafic and mafic oceanic rocks and radiolarites of Late Triassic, Jurassic and Early Cretaceous age: 1. The Siuna Serpentinite Mélange (NE-Nicaragua), 2. The El Castillo Mélange (Nicaragua/Costa Rica border), 3.The Santa Elena Ultramafics (N-Costa Rica) and, 4. DSDP Legs 67/84. 1. The Siuna Serpentinite Mélange contains, high pressure metamorphic mafics and Middle Jurassic (Bajocian-Bathonian) radiolarites in original, sedimentary contact with arc-metandesites. The Siuna Mélange also contains Upper Jurassic black detrital chert formed in a marginal (fore-arc?) basin shortly before subduction. A phengite 40Ar/39Ar -cooling age dates the exhumation of the high pressure rocks as 139 Ma (earliest Cretaceous). 2. The El Castillo Mélange comprises a radiolarite block tectonically embedded in serpentinite that yielded a diverse Rhaetian (latest Triassic) radiolarian assemblage, the oldest fossils recovered so far from S-Central America. 3. The Santa Elena Ultramafics of N-Costa Rica together with the serpentinite outcrops near El Castillo (2) in Southern Nicaragua, are the southernmost outcrops of the MCOT. The Santa Elena Unit (3) itself is still undated, but it is thrust onto the middle Cretaceous Santa Rosa Accretionary Complex (SRAC), that contains Lower to Upper Jurassic, highly deformed radiolarite blocks, probably reworked from the MCOT, which was the upper plate with respect to the SRAC. 4. Serpentinites, metagabbros and basalts have long been known from DSDP Leg 67/84 (3), drilled off Guatemala in the Nicaragua-Guatemala forearc basement. They have been restudied and reveal 40Ar/39Ar dated Upper Triassic to middle Cretaceous enriched Ocean Island Basalts and Jurassic to Lower Cretaceous depleted Island arc rocks of probable Pacific origin. The area between localities 1-4 is largely covered by Tertiary to Recent arcs, but we suspect that its basement is made of oceanic/accreted terranes. Earthquake seismic studies indicate an ill-defined, shallow Moho in this area. The MCOT covers most of Nicaragua and could extend to Guatemala to the W and form the Lower (southern) Nicaragua Rise to the NE. Some basement complexes of Jamaica, Hispaniola and Puerto Rico may also belong to the MCOT. The Nicoya Complex s. str. has been regarded as an example of Caribbean crust and the Caribbean Large Igneous Province (CLIP). However, 40Ar/39Ar - dates on basalts and intrusives indicate ages as old as Early Cretaceous. Highly deformed Jurassic and Lower Cretaceous radiolarites occur as blocks within younger intrusives and basalts. Our interpretation is that radiolarites became first accreted to the MCOT, then became reworked into the Nicoya Plateau in Late Cretaceous times. This implies that the Nicoya Plateau formed along the Pacific edge of the MCOT, independent form the CLIP and most probably unrelated with he Galapagos hotspot. No Jurassic radiolarite, no older sediment age than Coniacian-Santonian, and no older 40Ar/39Ar age than 95 Ma is known from S-Central America between SE of Nicoya and Colombia. For us this area represents the trailing edge of the CLIP s. str.

Geology of the NW Indian Himalaya

This review paper deals with the geology of the NW Indian Himalaya situated in the states of Jammu and Kashmir, Himachal Pradesh and Garhwal. The models and mechanisms discussed, concerning the tectonic and metamorphic history of the Himalayan range, are based on a new compilation of a geological map and cross sections, as well as on paleomagnetic, stratigraphic, petrologic, structural, metamorphic, thermobarometric and radiometric data. The protolith of the Himalayan range, the North Indian flexural passive margin of the Neo-Tethys ocean, consists of a Lower Proterozoic basement, intruded by 1.8-1.9 Ga bimodal magmatites, overlain by a horizontally stratified sequence of Upper Proterozoic to Paleocene sediments, intruded by 470-500 Ma old Ordovician mainly peraluminous s-type granites, Carboniferous tholeiitic to alkaline basalts and intruded and overlain by Permian tholeiitic continental flood basalts. No elements of the Archaen crystalline basement of the South Indian shield have been identified in the Himalayan range. Deformation of the Himalayan accretionary wedge resulted from the continental collision of India and Asia beginning some 65-55 Ma ago, after the NE-directed underthrusting of the Neo-Tethys oceanic crust below Asia and the formation of the Andean-type 103-50 (-41) Ma old Ladakh batholith to the north of the Indus Suture. Cylindrical in geometry, the Himalayan range consists, from NE to SW, from older to younger tectonic elements, of the following zones: 1) The 25 km wide Ladakh batholith and the Asian mantle wedge form the backstop of the growing Himalayan accretionary wedge. 2) The Indus Suture zone is composed of obducted slices of the oceanic crust, island arcs, like the Dras arc, overlain by Late Cretaceous fore arc basin sediments and the mainly Paleocene to Early Eocene and Miocene epi-sutural intra-continental Indus molasse. 3) The Late Paleocene to Eocene North Himalayan nappe stack, up to 40 km thick prior to erosion, consists of Upper Proterozoic to Paleocene rocks, with the eclogitic and coesite bearing Tso Morari gneiss nappe at its base. It includes a branch of the Central Himalayan detachment, the 22-18 Ma old Zanskar Shear zone that is intruded and dated by the 22 Ma Gumburanjun leucogranite; it reactivates the frontal thrusts of the SW-verging North Himalayan nappes. 4) The late Eocene-Miocene SW-directed High Himalayan or ``Crystalline'' nappe comprises Upper Proterozoic to Mesozoic sediments and Ordovician granites, identical to those of the North Himalayan nappes. The Main Central thrust at its base was created in a zone of Eocene to Early Oligocene anatexis by ductile detachment of the subducted Indian crust, below the pre-existing 25-35 km thick NE-directed Shikar Beh and SW-directed North Himalayan nappe stacks. 5) The late Miocene Lesser Himalayan thrust with the Main Boundary Thrust at its base consists of early Proterozoic to Cambrian rocks intruded by 1.8-1.9 Ga bimodal magmatites. The Subhimalaya is a thrust wedge of Himalayan fore deep basin sediments, composed of the Early Eocene marine Subathu marls and sandstones as well as the up to 8'000 m-thick Miocene to recent Ganga molasse, a coarsening upwards sequence of shales, sandstones and conglomerates. The active frontal thrust is covered by the sediments of the Indus-Ganga plains.

Post-Plutonic Magmatism: from the Source to the Emplacement of an Upper Crustal Dyke Swarm, Adamello Massif, Italy

Magmas of the arc-tholeiitic and calc-alkaline differentiation suites contribute substantially to the formation of continental crust in subduction zones. Different geochemical-petrological models have been put forward to achieve evolved magmas forming large volumes of tonalitic to granitic plutons, building an important part of the continental crust. Primary magmas produced in the mantle wedge overlying the subducted slab migrate through the mantle and the crust. During the transfer, magma can accumulate in intermediate reservoirs at different levels where crystallization leads to differentiation and the heat transfer from the magma, together with gained heat from solidification, lead to partial melting of the crust. Partial melts can be assimilated and mix with more primitive magma. Moreover, already formed crystal cumulates or crystal mushes can be recycled and reactivated to transfer to higher crustal levels. Magma transport in the crust involves fow through fractures within a brittle elastic rock. The solidified magma filled crack, a dyke, can crosscut previously formed geological structures and thus serves as a relative or absolute time marker. The study area is situated in the Adamello massif. The Adamello massif is a composite of plutons that were emplaced between 42 and 29 million years. A later dyke swarm intruded into the southern part of the Adamello Batholith. A fractionation model covering dyke compositions from picrobasalts to dacites results in the cummulative crystallization of 17% olivine, 2% Cr-rich spinel, 18% clinopyroxene, 41% amphibole, 4% plagioclase and 0.1% magnetite to achieve an andesitic composition out of a hydrous primitive picrobasalt. These rocks show a similar geochemical evolution as experimental data simulating fractional crystallization and associated magma differentiation at lower crustal depth (7-10 kbar). The peraluminous, corundum normative composition is one characteristic of more evolved dacitic magmas, which has been explained in a long lasting debate with two di_erent models. Melting of mafic crust or politic material provides one model, whereas an alternative is fractionation from primary mantle derived melts. Amphibole occurring in basaltic-andesitic and andesitic dyke rocks as fractionating cumulate phase extracted from lower crustal depth (6-7.5 kbar) is driving the magmas to peraluminous, corundum normative compositions, which are represented by tonalites forming most of the Adamello Batholith. Most primitive picrobasaltic dykes have a slightly steepened chondrite normalized rare earth elements (REE) pattern and the increased enrichment of light-REE (LREE) for andesites and dacites can be explained by the fractional crystallization model originating from a picrobasalt, taking the changing fractionating phase assemblage and temperature into account. The injection of hot basaltic magma (~1050°C) in a closely spaced dyke swarm increases the surface of the contact to the mainly tonalitic wallrock. Such a setting induces partial melting of the wall rock and selective assimilation. Partial melting of the tonalite host is further expressed through intrusion breccias from basaltic dykes. Heat conduction models with instantaneous magma injection for such a dyke swarm geometry can explain features of partial melting observed in the field. Geochemical data of minerals and bulk rock further underline the selective or bulk assimilation of the tonalite host rock at upper crustal levels (~2-3 kbar), in particular with regard to light ion lithophile elements (LILE) such as Sr, Ba and Rb. Primitive picrobasalts carry an immiscible felsic assimilant as enclaves that bring along refractory rutile and zircon with textures typically found in oceanic plagiogranites or high pressure/low-temperature metamorphic rocks in general. U-Pb data implies a lower Cretaceous age for zircon not yet described as assimilant in Eocene to Oligocene magmatic rocks of the Central Southern Alps. The distribution of post-plutonic dykes in large batholiths such as the Adamello is one of the key features for understanding the regional stress field during the post-batholith emplacement cooling history. The emplacement of the regional dyke swarm covering the southern part of the Adamello massif was associated with consistent left lateral strike-slip movement along magma dilatation planes, leading to en echelon segmentation of dykes. Through the dilation by magma of pre-existing weaknesses and cracks in an otherwise uniform host rock, the dyke propagation and according orientation in the horizontal plane adjusted continuously perpendicular to least compressive remote stress σ3, resulting in an inferred rotation of the remote principal stress field. Les magmas issus des zones de subduction contribuent substantiellement à la formation de la croûte continentale. Les plutons tonalitiques et granitiques représentent, en effet, une partie importante de la croûte continentale. Des magmas primaires produits dans le 'mantle wedge ', partie du manteau se trouvant au-dessus de la plaque plongeante dans des zones de subduction, migrent à travers le manteau puis la croûte. Pendant ce transfert, le magma peut s'accumuler dans des réservoirs intermédiaires à différentes profondeurs. Le stockage de magma dans ces réservoirs engendre, d'une part, la différentiation des magmas par cristallisation fractionnée et, d'autre part, une fusion partielle la croûte continentale préexistante associée au transfert de la chaleur des magmas vers l'encaissant. Ces liquides magmatiques issus de la croûte peuvent, ensuite, se mélanger avec des magmas primaires. Le transport du magma dans la croûte implique notamment un flux de magma à travers différentes fractures recoupant les roches encaissantes élastiques. Au cours de ce processus de migration, des cumulats de cristaux ou des agrégats de cristaux encore non-solidifiés, peuvent être recyclés et réactivés pour être transportés à des niveaux supérieures de la croûte. Le terrain d'étude est situé dans le massif d'Adamello. Celui-ci est composé de plusieurs plutons mis en place entre 42 et 29 millions d'années. Dans une phase tardive de l'activité magmatique liée à ce batholite, une série de filons de composition variable allant de picrobasalte à des compositions dacitiques s'est mise en place la partie sud du massif. Deux modèles sont proposés dans la littérature, pour expliquer la formation des magmas dacitiques caractérisés par des compositions peralumineux (i.e. à corindon normatif). Le premier modèle propose que ces magmas soient issus de la fusion de matériel mafique et pélitique présent dans la partie inférieur de la croûte, alors que le deuxième modèle suggère une évolution par cristallisation fractionnée à partir de liquides primaires issus du manteau. Un modèle de cristallisation fractionnée a pu être développé pour expliquer l'évolution des filons de l'Adamello. Ce modèle explique la formation des filons dacitiques par la cristallisation fractionnée de 17% olivine, 2% spinelle riche en Cr, 18% clinopyroxène, 41% amphibole, 4% plagioclase et 0.1% magnetite à partir de liquide de compositions picrobasaltiques. Ce modèle prend en considération les contraintes pétrologiques déduites de l'observation des différents filons ainsi que du champ de stabilité des différentes phases en fonction de la température. Ces roches montrent une évolution géochimique similaire aux données expérimentales simulant la cristallisation fractionnée de magmas évoluant à des niveaux inférieurs de la croûte (7-10 kbar). Le modèle montre, en particulier, le rôle prépondérant de l'amphibole, une phase qui contrôle en particulier le caractère peralumineux des magmas différentiés ainsi que leurs compositions en éléments en traces. Des phénomènes de fusion partielle de l'encaissant tonalitique lors de la mise en place de _lons mafiques sont observée sur le terrain. L'injection du magma basaltique chaud (~1050°C) sous forme de filons rapprochés augmente la surface du contact avec l'encaissante tonalitique. Une telle situation produit la fusion partielle des roches encaissantes nécessaire à l'incorporation d'enclaves mafiques observés au sein des tonalites. Pour comprendre les conditions nécessaires pour la fusion partielle des roches encaissantes, des modèles de conduction thermique pour une injection simultanée d'une série de filons ont été développées. Des données géochimiques sur les minéraux et sur les roches totales soulignent qu'au niveau supérieur de la croûte, l'assimilation sélective ou totale de l'encaissante tonalitique modifie la composition du liquide primaire pour les éléments lithophiles tel que le Sr, Ba et Rb. Un autre aspect important concernant la pétrologie des filons de l'Adamello est la présence d'enclaves felsiques dans les filons les plus primitifs. Ces enclaves montrent, en particulier, des textures proches de celles rencontrées dans des plagiogranites océaniques ou dans des roches métamorphiques de haute pression/basse température. Ces enclaves contiennent du zircon et du rutile. La datations de ces zircons à l'aide du géochronomètre U-Pb indique un âge Crétacé inférieur. Cet âge est important, car aucune roche de cet âge n'a été considérée comme un assimilant potentiel pour des roches magmatiques d'âge Eocène à Oligocène dans les Alpes Sud Centrales. La réparation spatiale des filons post-plutoniques dans des grands batholites tel que l'Adamello, est une caractéristique clé pour la compréhension des champs de contraintes lors du refroidissement du batholite. L'orientation des filons va, en particulier, indiqué la contrainte minimal au sein des roches encaissante. La mise en place de la série de filon recoupant la partie Sud du massif de l'Adamello est associée à un décrochement senestre, un décrochement que l'on peut lié aux contraintes tectoniques régionales auxquelles s'ajoutent l'effet de la dilatation produite par la mise en place du batholite lui-même. Ce décrochement senestre produit une segmentation en échelon des filons.

Termination of major ductile strike-slip shear and differential cooling along the Insubric line (Central Alps): U-Pb, Rb-Sr and 40Ar/39Ar ages of cross-cutting pegmatites

To constrain the age of strike-slip shear, related granitic magmatism, and cooling along the Insubric line, 29 size fractions of monazite and xenotime were dated by the U-Pb method, and a series of 25 Rb-Sr and Ar-40/Ar-39 ages were measured on different size fractions of muscovite and biotite. The three pegmatitic intrusions analyzed truncate high-grade metamorphic mylonite gneisses of the Simplon shear zone, a major Alpine structure produced in association with dextral strike-slip movements along the southern edge of the European plate, after collision with its Adriatic indenter. Pegmatites and aplites were produced between 29 and 25 Ma in direct relation to right-lateral shear along the Insubric line, by melting of continental crust having Sr-87/Sr-86 between 0.7199 and 0.7244 at the time of melting. High-temperature dextral strike-slip shear was active at 29.2 +/- 0.2 (2 sigma) Ma, and it terminated before 26.4 +/- 0.1 Ma. During dike injection, temperatures in the country rocks of the Isorno-Orselina and Monte Rosa structural units did not exceed approximate to 500 degrees C, leading to fast initial cooling, followed by slower cooling to approximate to 350 degrees C within several million years. In one case, initial cooling to approximate to 500 degrees C was significantly delayed by about 4 m.y., with final cooling to approximate to 300 degrees C at 20-19 Ma in all units. For the period between 29 and 19 Ma, cooling of the three sample localities was non-uniform in space and time, with significant variations on the kilometre scale. These differences are most likely due to strongly varying heat flow, and/or heterogeneous distribution of unroofing rates within the continuously deforming Insubric line. If entirely ascribed to differences in unroofing, corresponding rates would vary between 0.5 and 2.5 mm/y, for a thermal gradient of 30 degrees/km.

Pseudo-two-girdles c-axis fabric patterns in a quartz-feldspar mylonite (Costabona granodiorite, Canigo massif)

An example of the relationship that exist between the preferred crystaliografic orientation of quartz grains and the attitude of the mylonite foliation of quartz-feldspar mylonites is described. These rocks are the result of the inhomogeneous deformation under low-grade metamorphic conditions of a late Hercynian granodiorite, intruded into the gneisses of the slopes of the Canig massif (Eastern Pyrenees). The Costabona mylonites have a quartz c-axis fabric in pseudo-twogirdles symmetrical with respect to the mylonite foliation and perpendicular to the shearband systems which produce an extensional crenulation of the mylonite foliation.

Las comunidades de líquenes de las rocas silíceas no volcánicas del SE de España

This study contains the results of a survey based on 200 relevés made, following the methodology of Klement (1955), in the provinces of Murcia, Almeria and Albacete, from the coast to 2000 msm, on siliceous rocks, mainly metamorphic schists and, more rarely, on quartzite. The climate is predominantly mediterranean and arid (from 180 to 500 mm of annual rainfall), and belongs to I11 and III(1V) types of Walter and Lieth, in the low regions, and to IV4 in the mountains. The coastal zone and also a lot of south-facing slopes enjoy fairly warm winters.

Frost Action in Rocks and Concrete, HR-258, 1986

The objectives of the project were to develop methodologies for (i) prediction and measurement of the magnitude of pressure which develops within pores of saturated porous materials upon freezing, (ii) determination of pore structure (pore size distribution) of porous materials; (iii) prediction and measurement of the rate with which pore ice grows; and (iv) prediction of frost susceptibility of porous materials with varying pore structures. As with all research endeavors solution of one problem leads to another one and this project was no exception. Emergence of new problems and the measures taken as the work progressed were discussed in progress reports submitted to the board. This final report will discuss only the conclusive finds and suggest measures to be taken for future investigations. The theory discussed in the proposal is not repeated in this report for the sake of brevity. However, the paper published as part of this project containing the theory is attached as Appendix I for the reader interested in the theory. In conformity with the objectives, this report consists of four parts. In accordance with the project contract two ice porosimeters were built and one will be delivered to the Iowa DOT after training of a DOT technician under the supervision of Mr. Wendell Dubberke with assistance from ISU researchers. During the training period debugging and further improvements in software will continue.

Radiometric age constraints on mineral growth, metamorphism, and tectonism of the Gummfluh klippe, Brianconnais domain of the Prealpes, Switzerland

A combined Ar-40/Ar-39, K/Ar, Rb/Sr and stable isotope study has been made of white micas from the Gummfluh klippe (Brianconnais domain of the Prealpes), Switzerland. The klippe consists mainly of Mesozoic to early Tertiary carbonate rocks metamorphosed from anchizonal to epizonal conditions. At the base of the klippe is a 10-50 m thick, ductilely deformed marble mylonite containing deformed authigenic quartz segregations. Stable isotope measurements of the coexisting calcite (deltaO-18SMOW=24.5) and quartz (deltaO-18SMOW=28.4) from the mylonite indicate relatively low temperatures (< 300-degreesC) during mylonitization. Analyses of white mica separates of varying size fractions from the mylonitic rocks by K/Ar and Rb/Sr techniques yield ages between 57 and 103 Ma. This variation is correlated with two parameters, the size of the mineral fraction, and the proportion of 2M1 (more phengitic) to 1M (more muscovitic) polytype in the sample. The K/Ar and Rb/Sr ages are generally younger in the smaller size fractions, which also containless 2M1 phengite. High precision Ar-40/Ar-39 age spectra from different size fractions of these micas record three distinct components, a small Hercynian component (ca. 200-300 Ma), a significant Eoalpine component (64-80 Ma) forming Ar-40/Ar-39 age plateaus, and a very minor Tertiary component (ca. 20-40 Ma). Characterization of the samples by SEM indicates the presence of two white mica populations, a coarser grained, deformed, detrital mica that probably corresponds to the 2M1 phengite and a finer grained neoformed 1M mica. Collectively these observations suggest that the Gummfluh samples contain a mixture of detrital phengites of Hercynian age together with neocrystallized muscovites grown during the late Eoalpine metamorphic event followed by minor argon loss during the Tertiary. The main geologic episode recorded in the Ar-40/Ar-39 age spectra of white micas in the mylonite is of Late Cretaceous/Early Tertiary age (64-80 Ma), representing the first reliable Eoalpine ages ever to be reported from the Prealpes. Contrary to tectonic models, the marble mylonite at the base of the Gummfluh klippe appears to be a Cretaceous thrust plane and not the thrust surface formed during transport of the klippe into its present position from the Penninic Alps during the Tertiary. The late Cretaceous thrust developed during marine sedimentation at a depth of 800 m below the seafloor at temperatures of approximately 280-degrees-C, facilitated by warm fluids along the tectonic discontinuity.

Structure and kinematics of the Jungfrau syncline, Faflertal (Valais, Alps), and its regional significance

The formation and structural evolution of the jungrau syncline is described, based on excellent outcrops occurring in the lotschental, in the central alps of switzerland. the quality of the outcrops allows us to demonstrate that the external massifs of the swiss alps have developed due to internal folding. The jungfrau suncline, which separates the autochtonous gastern dome from the aar massif basement gneiss folds, is composed of slivers of basement rocks with their mesozoic sedimentary cover. in the inner faflertal, a side valley of the lotschental, the 200 m thick syncline cp, roses fpir imots, the gastern massif with a reduced mesozoic sedimentary cover in a normal stratigraphic succession, two units of overturned basement rocks with their mesozoic sedimentary cover, and the overturned lower limn of the tschingelhorn gneiss fold of the aar massif with lenses of its sedimentary cover. stratigraphy shows that the lower units, related to the gastern massis, are condensed and that the upper units, deposited farther away from a gastern paleo-high, form a more complete sequence, linked to the doldenhorn meso-cneozoic basin fill. the integration of these local observations with published regional data leads to the following model. on the northern margin of the doldenhorn hbasin, at the northern fringe of the alpine tethuys, the pre-triassic crystalline basement and its mesozoic sedimentary cover were folded by ductile deformation at temperatures above 300 degrees C and in the presence of high fluid pressures, as the helveti c and penninic nappes were overthrusted towards the northwest during the main alpine deformation phase, the visosity contrast between the basement gneisses and the sediments caused the formation of large basement anticlines and tight sedimentary sunclines (mullion-type structures). The edges of basement blocks bounded buy pre-cursor se-dipping normal faults at the northwestern border of the doldenhorn basin were deformed bu simple shear, creating overturned slices of crystalline rocks with their sedimentary cover in what now forms the hungfrau syncline. the localisation of ductile deformation in the vicinity of pre-existing se-dipping faults is thought to have been helped by the circulation of fluids along the faults; these fluids would have been released from the mesozoic sediments by metamorphic dehydration reactions accompanied by creep and dynamic recrystallisation of quartz at temperatures above 300 degrees C. Quantification of the deformation suggests an strain ellipsoid with a ratio (1 + e(1)/+ e(3)) of approximately 1000. The jungfrau suncline was deformed bu more brittle nw-directed shear creating well-developed shear band cleavages at a late stage, after cooling by uplift and erosion. It is suggested that the external massifs of the apls are basement gneiss folds created at temperatures of 300 degrees C by detachment through ductile deformation of the upper crust of the european plate as it was underthrusted below the adriatic plate.

A Variscan pressure-temperature-time path for the N-E Mont Blanc massif

The northeastern portion of the Mont Blanc massif in western Switzerland is predominantly comprised of the granitic rocks of the Mont Blanc intrusive suit, and the Mont Blanc basement gneisses. Within these metamorphic rocks are a variety of sub-economic Fe skarns. The mineral assemblages and fluid inclusions from these rocks have been used to derive age, pressure, temperature and fluid composition constraints for two Variscan events. Metamorphic hornblendes within the assemblages from the basement amphibolites and iron sk:lms have been dated using Ar-40/Ar-39, and indicate that these metamorphic events have a minimum age of approximately 334 Ma. Garnet-hornblende-plagioclase thermobarometry and stable isotope data obtained from the basement amphibolites are consistent with metamorphic temperatures in the range 515 to 580 degrees C, and pressures ranging from 5 to 8 kbar. Garnet-hornblende-magnetite thermobarometry and fluid inclusion studies indicate that the iron skarns formed at slightly lower temperatures, ranging from 400 to 500 degrees C in the presence of saline fluids at formational pressures similar to those experienced by the basement amphibolites. Late Paleozoic minimum uplift rates and geothermal gradients calculated using these data and the presence of Ladinien ichnofossils are on the order of 0.32 mm/year and 20 degrees C/km respectively. These uplift rates and geothermal gradients differ from those obtained from the neighbouring Aiguilles Rouges massif and indicate that these two massifs experienced different metamorphic conditions during the Carboniferous and Permian periods. During the early to late Carboniferous period the relative depths of the two massifs were reversed with the Aiguilles Rouges being initially unroofed at a much greater rate than the Mont Blanc, but experiencing relatively slower uplift rates near the termination of the Variscan orogeny.

Fluid-rock interaction during late stages of the Alpine exhumation

Résumé de la thèseLa fracturation des roches au cours de phases compressives ou extensives est un souvent évoquée pour expliquer la circulation de fluide au sein des roches cristallines. Dans le cadre de cette thèse, la circulation des fluides lors de l'exhumation tardive des Alpes a été étudiée en utilisant deux approches différentes: analyses structurales de la déformation fragile d'une part et analyses géochimiques des roches et des minéraux (isotopes stables, datations U/Pb, thermochronologie (U-Th)/He) d'autre part. Cette approche combinée a permis de mieux comprendre l'interaction existante entre les fluides métamorphiques et les fluides météoriques, ainsi que leur interaction avec les roches encaissantes. Le travail a été effectué dans la zone Pennique du Valais suisse.La première partie était focalisée sur la déformation fragile, le but étant de définir les différents types de déformations existantes et de déterminer l'âge relatif des différentes familles de failles. Dans la région d'étude, quatre domaines ont été distingués. Chacun d'eux comportent deux types de structures fragiles, certaines sont minéralisées alors que d'autre non. Au sein de chaque domaine, la direction principale des structures minéralisées correspond à l'orientation des accidents tectoniques majeurs de la région (Aosta- Ranzola Line au Sud, Rhône Line au Nord et Simplon Fault Zone à l'Est), alors que les structures non- minéralisées montrent des orientations plus variables. Ainsi, le premier type de structure est interprété comme résultant d'une dislocation tectonique alors que le deuxième type de structure résulterait d'une dislocation gravitaire locale. Il n'est néanmoins pas possible de classer chronologiquement la formation de ces deux types de structure ni d'attribuer un âge relatif aux changements d'orientation des contraintes majeures.La deuxième étude a été effectuée dans la région de la zone de faille du Simplon. Dans cette zone, la composition isotopique des minéraux ayant cristallisé à l'intérieur des fractures tardives permet de distinguer différents types de circulation de fluide. Les valeurs δ180 du quartz de la roche encaissante ainsi que ceux des veines tardives du bloque inférieur de la faille sont comparables. Ces valeurs indiquent un rééquilibrage et un tamponnage isotopique des fluides tardifs au contact de la roche encaissante lors de la fracturation de cette dernière et de la cristallisation des veines tardives. La même situation est observée dans la partie nord du bloque supérieur ainsi que dans sa partie sud. Ceci n'est néanmoins pas le cas pour la partie centrale du bloque supérieur où les valeurs isotopiques des minéraux dans les veines tardives sont approximativement 3 %o plus basses (avec des valeurs extrêmes négatifs), indiquant une contribution d'eau météorique aux fluides circulant dans les veines. Ces données suggèrent qu'une infiltration d'eau météorique a pu avoir lieu dans le bloque supérieur, où la fracturation des roches est plus intensive car le déplacement relatif le long de la faille y fut plus important, et la température maximale du métamorphisme plus basse. La troisième contribution traite de la géo-thermochronologie de la zone de contact entre la klippe de la Dent Blanche et la nappe de Tsaté. De petits zircons euhédraux ont été trouvés dans un plan de faille minéralisé (parallèle à la Faille du Rhône, voir première partie de l'étude), riche en hématite et quartz, de la zone d'étude. Les analyses U/Pb donnent des âges radiométriques autour de 270 - 280 Ma aux zircons extraits de la minéralisation ainsi que ceux extraits de la roche encaissante, ce qui correspond à l'âge de la nappe de la Dent Blanche et non celui de la nappe du Tsaté qui est elle-même classiquement interprétée comme une ophiolite Jurassique de l'Océan Liguro-Piémontais. Ces données suggèrent que les zircons contenus dans la veine ont été hérités de la roche encaissante. Les résultats (U-Th)/He indiquent un âge de refroidissement différent pour la roche encaissante (25.5 ± 2.0 Ma) que celui de la minéralisation (17.7 ±1.4 Ma). Le thermomètre isotopique quartz-hématite indique une température d'équilibre, et donc de mise en place de la minéralisation, d'environ 170 °C, température très proche de la température de -180 °C de fermeture du zircon pour le système (U-Th)/He. Ceci suggère que l'âge de refroidissement des zircons de la minéralisation correspond aussi à l'âge de formation de la faille.Thesis abstractFluid circulation in fractured rocks is a common process in geology, and it is generally the consequence of faulting and fracturing during both tectonic compression and extension. This thesis is focused on fluid circulation during late stages of the Alpine exhumation. After a structural analysis of the late brittle deformation of the studied samples, several analytical methods (stable isotope investigations, U/Pb radiometric dating, (U-Th)/He thermochronology) have been applied to understand the interaction of metamorphic and meteoric fluids with one another as well as with the host rock. This thesis is articulated around three study directions. All studies were conducted in the Penninic Zone of the Valais, Switzerland. The first study deals with late, brittle deformation and focuses on the different deformation styles and on the relative age of the different families of fractures. In order to do this, late brittle structures observed in four different domains have been subdivided as a function of the existence (or not) and type of mineralization. Comparisons between mineralized and non-mineralized strike directions for all four domains show that mineralized structures follow the strike orientation of major tectonic movements indicated in the Penninic Zone of the Valais (Aosta-Ranzola Line to the S, Rhône Line to the Ν and Simplon Fault Zone to the E), whereas non-mineralized fractures have a more variable strike orientation. This difference could be interpreted as indicative of tectonic-related faulting (mineralized structures) vs. local, collapse-related faulting (non-mineralized fractures), but it is not strong enough to indicate a relative age of the late brittle structures, and/or a change in the orientation of the strain field in post-Miocene times. The second studied area is focused on the Simplon Fault Zone (SFZ). Stable isotope analyses of minerals filling these late fractures indicate that there are two different fluid circulation systems in the footwall and hanging wall of the SFZ. In the footwall, δ180 values of quartz from both the host rock and the late veins range from +10 %o to +12 %o. This is consistent with buffering of circulating fluids by the host rock during fracturing and vein precipitation. In the hanging wall, δΙ80 values for quartz crystals from the host rock and the late veins are similar in both the northern and southern parts of the detachment that are both affected by the same degree of metamorphism (greenschist to the Ν and amphibolite to the S). This is not the case in the central part of the SFZ, where there is a jump from amphibolite facies in the footwall to greenschist facies in the hanging wall. δ,80 values for quartz from the hanging wall late veins are approximately 3.0 %o lower (down to negative values in some cases) than the values observed in the footwall These data suggest that infiltration of meteoric water may have occurred in the most fractured parts of the hanging wall, where relative displacement on the SFZ was the greatest and the peak temperature lower. In the less fractured footwall the δ180 values reflect a host rock-buffered system.The third study is focused on geo-thermochronology at the contact between the Dent Blanche nappe and the Tsaté nappe where small, euhedral zircons were found in a hematite- and quartz-rich mineralization on a late normal fault plane parallel to the Rhône Line (see first part of the study). U/Pb analysis indicates that the zircons - both in the late mineralization and in the host rock - have absolute radiometric ages clustering around 270 - 280 Ma, which is the accepted age for intrusive rocks from the Austroalpine Dent Blanche units but not for the Tsaté nappe. The latter is classically interpreted as an ophiolitic remnant of the Jurassic Liguro-Piemontais Ocean. U/Pb analyses suggest that zircons in late mineralization are all inherited from the host rock; however, results of (U-Th)/He analyses indicate that cooling ages for the host rocks are different to the cooling ages for the zircons in late mineralization. Indeed, the calculated cooling age for the Arolla gneiss is 25.5 ± 2.0 Ma, whilst the cooling age for the associated mineralized fault plane is 17.7 ±1.4 Ma. Oxygen stable isotope fractionation between quartz and hematite in the same late mineralization corresponds to temperatures of about 170 °C. The proximity of the calculated emplacement temperature for the mineralization and the lower accepted closure temperature for zircon in the (U-Th)/He system (-180 °C) imply that the age of 17.7 ± 1.4 Ma can also be interpreted as the formation age of this late brittle fault.Résumé grand publicLa circulation des fluides dans les roches fracturées est typique de nombreux processus géologiques, et très souvent est la conséquence de la fracturation des roches. Cette thèse aborde la question de la circulation des fluides pendant les dernières phases du soulèvement des Alpes. Après une analyse structurale de la fracturation directement sur le terrain, plusieurs méthodes géochimiques ont été appliquées pour comprendre l'interaction entre les différents fluides circulants, et avec leur propre roche mère. L'étude, concentrée sur trois directions principales, a été conduite dans la zone Pennique du Valais suisse. La première partie traite de la déformation cassante dans le secteur cité. L'analyse détaillée des fractures a permis de les subdiviser en structures minéralisées et non-minéralisées, sur quatre domaines différents. La comparaison entre les directions des structures minéralisées et non-minéralisées a permis de montrer que les premières suivent l'orientation des accidents tectoniques majeurs de la région, alors que les structures non- minéralisées ont une orientation plus variable. Cette différence pourrait être interprétée comme indication d'une dislocation tectonique (structures minéralisées) contre une dislocation gravitaire locale (structures non-minéralisées), mais elle n'est pas assez forte pour indiquer un âge relatif des structures tardives et/ou un changement de l'orientation des contraintes après -20 Ma vers le présent.A partir de ces observations, la deuxième étude est concentrée dans la région de la faille du Simplon. Les analyses géochimiques sur les minéraux remplissant les structures tardives indiquent qu'il y a deux différents systèmes de circulation des fluides dans les deux parties (toit et mur) de la faille. Dans le mur, les valeurs isotopiques des minéraux cristallisés à partir d'un fluide tardif sont les mêmes de ceux de la roche mère, donc il y a eu rééquilibration chimique entre fluide et roche pendant la fracturation de cette dernière et la précipitation des minéraux. Dans le toit, les valeurs isotopiques dans la roche mère et dans les minéraux des veines tardives sont comparables dans les parties Ν et S de la faille, où les roches du toit et du mur ont atteint une température maximale - pendant phase prograde de la formation des Alpes - comparable. Au contraire, dans la partie centrale, où le mur a atteint des températures maximales plus élevées par rapport au toit, les valeurs géochimiques des minéralisations tardives du toit sont parfois plus basses que les valeurs observées dans le mur. Ces données suggèrent que l'infiltration de l'eau de surface aurait pu se produire dans la partie plus fracturée du toit, où le déplacement relatif le long de la faille était majeur et les températures maximales mineures. Au contraire, les données géochimiques du mur de la partie centrale indiquent un système isotopique équilibré par la roche mère.La troisième partie de ce travail se base sur l'étude géochimique intégrée des isotopes stables d'Oxygène et radioactifs du Plomb, Uranium, Thorium et Hélium, auprès d'une faille normale minéralisée et des roches de la région à cheval entre deux nappes, la nappe de la Dent Blanche et la nappe de Tsaté. Ici, des petits zircons ont été trouvés dans la minéralisation citée, riche en hématite et quartz. L'analyse radiométrique Uranium/Plomb a montré que les zircons dans la minéralisation et dans les roches autour ont des âges comparables (autour 280 Ma). Cela signifie que les zircons dans la minéralisation tardive ont été hérités de la roche mère pendant la fracturation et la circulation des fluides tardives. De l'autre coté, les résultats des analyses Uranium-Thorium/Hélium indiquent que les âges de refroidissement pour les roches mères sont différents comparés aux âges de refroidissement pour les zircons dans la minéralisation tardive: ces derniers sont plus jeunes d'environ 8 Ma (autour 25 Ma et autour 17 Ma respectivement). Les analyses des isotopes de l'oxygène sur quartz et hématite dans la même minéralisation donnent une température de mise en place de cette dernière d'environ 170° C. La température de fermeture du système chimique des zircons dans le système (Uranium-Thorium)/Hélium est d'environ 180 °C: la proximité de ces deux températures implique que l'âge de refroidissement de la minéralisation tardive peut également être interprété comme âge de formation de la faille.

Compositional and Mechanical Properties of Carbonate Rocks, HR-110, 1967

The research project, HR-110, was begun in the fall of 1964 to further investigate the compositional and mechanical properties of some of the carbonate rocks used as aggregate in portland cement concrete. Samples were taken only from those portions of the quarries that are used as aggregate in portland cement concrete by the Iowa State Highway Commission except where designated by commission personnel for purposes of evaluation of potential aggregate sources. Where practical, the samples were taken from each bed recognized by the Highway Commission geologists, and in most instances, the thicker beds were sampled at the top, middle, and bottom to detect any lithologic changes that escaped megascopic observation.