Preparation and characterization of multiwalled carbon nanotube-supported platinum for cathode catalysts of direct methanol fuel cells

Multiwalled carbon nanotube-supported Pt (Pt/MWNT) nanocomposites were prepared by both the aqueous solution reduction of a Pt salt (HCHO reduction) and the reduction of a Pt ion salt in ethylene glycol solution. For comparison, a Pt/XC-72 nanocomposite was also prepared by the EG method. The Pt/MWNT catalyst prepared by the EG method has a high and homogeneous dispersion of spherical Pt metal particles with a narrow particle-size distribution. TEM images show that the Pt particle size is in the range of 2-5 nm with a peak at 2.6 nm, which is consistent with 2.5 nm obtained from the XRD broadening calculation. Surface chemical modifications of MWNTs and water content in EG solvent are found to be the key factors in depositing Pt particles on MWNTs. In the case of the direct methanol fuel cell (DMFC) test, the Pt/MWNT catalyst prepared by EG reduction is slightly superior to the catalyst prepared by aqueous reduction and displays significantly higher performance than the Pt/XC-72 catalyst. These differences in catalytic performance between the MWNT-supported or the carbon black XC-72-supported catalysts are attributed to a greater dispersion of the supported Pt particles when the EG method is used, in contrast to aqueous HCHO reduction and to possible unique structural and higher electrical properties when contrasting MWNTs to carbon black XC-72 as a support.

Preparation of uniform calcium alginate gel beads by membrane emulsification coupled with internal gelation

With the objective of making calcium alginate gel beads with small and uniform size, membrane emulsification coupled with internal gelation was proposed. Spherical gel beads with mean size of about 50 mum, and even smaller ones in water, and with narrow size distribution were successfully obtained. Experimental studies focusing mainly on the effect of process parameters on bead properties were performed. The size of the beads was mainly dependent on the diameter of the membrane pores. High transmembrane pressure made for large gel beads with wide size distribution. Low sodium alginate concentration produced nonspherical beads, whereas a high concentration was unsuitable for the production of small beads with narrow distribution. Thus 1.5% w/v was enough. A high surfactant concentration favored the formation of small beads, but the adverse effect on mass transfer should be considered in this novel process. (C) 2002 Wiley Periodicals, Inc.

Preparation and characteristics of nonflammable polyimide materials

The thermal and flame-retardant properties of homo- and copolyimides were evaluated. Those containing sulfone linkages in the backbone were found to be more flame retardant. Both properties were dependent on the composition. A polyimide/silica nanocomposite was obtained through sol-gel processing. The effects of the addition of silica an the dispersion, interfacial adhesion, fire resistance, mechanical properties, and thermal stability of the composites were investigated. SEM analysis showed a good dispersion of silica with a diameter of 50-300 nm in the organic matrices. The addition of silica increased the fire retardancy and mechanical properties of the composites. (C) 2000 John Wiley & Sons, Inc.

Microwave-assisted preparation of 2-methallyloxyphenol

Catechol reacted with beta-methallyl chloride in the presence of base and phase transfer catalyst under microwave irradiation and gave 2-methallyloxyphenol within 1 similar to 2 minutes. The yield of 2-methallyloxyphenol varied from 64%similar to 68%.

A simple preparation of stationary phase of alkylamide reversed-phase liquid chromatograph for the separation of basic substances

A simple preparation process of alkylamide phase for reversed-phase HPLC (RP-HPLC) is described. The process includes aminopropyltrimethoxysilane firstly reacted with octanoyl chloride, then the intermediate was coupled onto porous silica. The resultant bonded silica has a reproducible ligand surface concentration and homogenous bonded ligand distribution on the porous silica. Characterization of prepared packing was carried out with elemental analysis, solid-state C-13 NMR and Fourier transform infrared (FT-IR). Chromatographic evaluations were carried out by using a mixture of organic compounds including acidic, basic and neutral analytes under methanol/water as binary mobile phase. The results showed that the stationary phase have excellent chromatographic properties and can be efficiently used for the separation of basic compounds.

Preparation and characterization of a novel macrocyclic ligand—dinitro-tetraazacyclotetradeca-tetraene—and application as a highly selective extractant for copper(II)

A novel tetraaza macrocyclic Schiff base ligand, 6,13-dinitro-5,7,12,14-tetramethyl-1,4,8,11-tetraazacyclotetradeca-1,5,7,-12-tetraene, was prepared and its copper(II) and nickel(II) complexes were characterized. This ligand was found to be an excellent extractant for copper(II).

Preparation and Characterization of BaLiF3:Er3+ Nanoparticles by the Hydrothermal Microemulsion Synthesized Method

Nanoparticles of BaLiF3:Er3+ were prepared from the quaternary microemulsions of Cetyltrim-Enthyl Ammonium Bromide (CTAB), n-butanol, n-octane, and water, using the hydrothermal-microemulsion technique. The complex fluorides were characterized by means of X-ray power diffraction, Environmental Scanning Electron Microscopy (ESEM), and fluorescence spectra.

Preparation and characterization of Gd2O3:Eu3+ luminescence nanotubes

The size controllable Gd2O3:Eu3+ luminescence nanotubes were successfully prepared using a simple method by coating gadolinium compounds on the carbon nanotubes and then firing the carbon nanotubes. The morphology of the obtained Gd2O3:Eu3+ nanotubes was determined by transmission electron microscopy (TEM). It was found that the obtained nanotubes have the outer diameters of similar to 100 nm, the inner diameters of similar to 50 nm, and the lengths of several tens of microns. The sizes of Gd2O3:Eu3+ nanotubes can be easily controlled by changing the reaction times and the concentration of reactants.

Preparation and upconversion luminescence of nanocrystalline Gd2O3 : Er3+, Yb3+

Nanocrystalline Gd1.77Yb0.2 Er0.03O3 samples were prepared by combustion and precipitation methods. Structures and upconversion luminescence properties of samples were studied. The results of XRD show that all samples are cubic structure, the average crystallite size could be calculated as 23 nm and 39 nm, respectively. The lattice constants were obtained. The FT-IR spectra were measured to investigate the vibrational feature of the samples.