Review of water electrolysis technologies and design of renewable hydrogen production systems

An electric system based on renewable energy faces challenges concerning the storage and utilization of energy due to the intermittent and seasonal nature of renewable energy sources. Wind and solar photovoltaic power productions are variable and difficult to predict, and thus electricity storage will be needed in the case of basic power production. Hydrogen’s energetic potential lies in its ability and versatility to store chemical energy, to serve as an energy carrier and as feedstock for various industries. Hydrogen is also used e.g. in the production of biofuels. The amount of energy produced during hydrogen combustion is higher than any other fuel’s on a mass basis with a higher-heating-value of 39.4 kWh/kg. However, even though hydrogen is the most abundant element in the universe, on Earth most hydrogen exists in molecular forms such as water. Therefore, hydrogen must be produced and there are various methods to do so. Today, the majority hydrogen comes from fossil fuels, mainly from steam methane reforming, and only about 4 % of global hydrogen comes from water electrolysis. Combination of electrolytic production of hydrogen from water and supply of renewable energy is attracting more interest due to the sustainability and the increased flexibility of the resulting energy system. The preferred option for intermittent hydrogen storage is pressurization in tanks since at ambient conditions the volumetric energy density of hydrogen is low, and pressurized tanks are efficient and affordable when the cycling rate is high. Pressurized hydrogen enables energy storage in larger capacities compared to battery technologies and additionally the energy can be stored for longer periods of time, on a time scale of months. In this thesis, the thermodynamics and electrochemistry associated with water electrolysis are described. The main water electrolysis technologies are presented with state-of-the-art specifications. Finally, a Power-to-Hydrogen infrastructure design for Lappeenranta University of Technology is presented. Laboratory setup for water electrolysis is specified and factors affecting its commissioning in Finland are presented.

Hemodialysis improves endothelial venous function in end-stage renal disease

The objective of the present study was to determine the acute effect of hemodialysis on endothelial venous function and oxidative stress. We studied 9 patients with end-stage renal disease (ESRD), 36.8 ± 3.0 years old, arterial pressure 133.8 ± 6.8/80.0 ± 5.0 mmHg, time on dialysis 55.0 ± 16.6 months, immediately before and after a hemodialysis session, and 10 healthy controls matched for age and gender. Endothelial function was assessed by the dorsal hand vein technique using graded local infusion of acetylcholine (endothelium-dependent venodilation, EDV) and sodium nitroprusside (endothelium-independent venodilation). Oxidative stress was evaluated by measuring protein oxidative damage (carbonyls) and antioxidant defense (total radical trapping antioxidant potential - TRAP) in blood samples. All patients were receiving recombinant human erythropoietin for at least 3 months and were not taking nitrates or a-receptor antagonists. EDV was significantly lower in ESRD patients before hemodialysis (65.6 ± 10.5) vs controls (109.6 ± 10.8; P = 0.010) and after hemodialysis (106.6 ± 15.7; P = 0.045). Endothelium-independent venodilation was similar in all comparisons performed. The hemodialysis session significantly decreased TRAP (402.0 ± 53.5 vs 157.1 ± 28.3 U Trolox/µL plasma; P = 0.001). There was no difference in protein damage comparing ESRD patients before and after hemodialysis. The magnitude of change in the EDV was correlated negatively with the magnitude of change in TRAP (r = -0.70; P = 0.037). These results suggest that a hemodialysis session improves endothelial venous function, in association with an antioxidant effect.

Hypoxic-ischemic injury decreases anxiety-like behavior in rats when associated with loss of tyrosine-hydroxylase immunoreactive neurons of the substantia nigra

Neonatal Sprague-Dawley rats were randomly divided into normal control, mild hypoxia-ischemia (HI), and severe HI groups (N = 10 in each group at each time) on postnatal day 7 (P7) to study the effect of mild and severe HI on anxiety-like behavior and the expression of tyrosine hydroxylase (TH) in the substantia nigra (SN). The mild and severe HI groups were exposed to hypoxia (8% O2/92% N2) for 90 and 150 min, respectively. The elevated plus-maze (EPM) test was performed to assess anxiety-like behavior by measuring time spent in the open arms (OAT) and OAT%, and immunohistochemistry was used to determine the expression of TH in the SN at P14, P21, and P28. OAT and OAT% in the EPM were significantly increased in both the mild (1.88-, 1.99-, and 2.04-fold, and 1.94-, 1.51-, and 1.46-fold) and severe HI groups (1.69-, 1.68-, and 1.87-fold, and 1.83-, 1.43-, and 1.39-fold, respectively; P < 0.05). The percent of TH-positive cells occupying the SN area was significantly and similarly decreased in both the mild (17.7, 40.2, and 47.2%) and severe HI groups (16.3, 32.2, and 43.8%, respectively; P < 0.05). The decrease in the number of TH-positive cells in the SN and the level of protein expression were closely associated (Pearson correlation analysis: r = 0.991, P = 0.000 in the mild HI group and r = 0.974, P = 0.000 in the severe HI group) with the impaired anxiety-like behaviors. We conclude that neonatal HI results in decreased anxiety-like behavior during the juvenile period of Sprague-Dawley rats, which is associated with the decreased activity of TH in the SN. The impairment of anxiety and the expression of TH are not likely to be dependent on the severity of HI.

Acute exposure to lead increases myocardial contractility independent of hypertension development

We studied the effects of the acute administration of small doses of lead over time on hemodynamic parameters in anesthetized rats to determine if myocardial contractility changes are dependent or not on the development of hypertension. Male Wistar rats received 320 µg/kg lead acetateiv once, and their hemodynamic parameters were measured for 2 h. Cardiac contractility was evaluated in vitro using left ventricular papillary muscles as were Na+,K+-ATPase and myosin Ca2+-ATPase activities. Lead increased left- (control: 112 ± 3.7 vs lead: 129 ± 3.2 mmHg) and right-ventricular systolic pressures (control: 28 ± 1.2vs lead: 34 ± 1.2 mmHg) significantly without modifying heart rate. Papillary muscles were exposed to 8 µM lead acetate and evaluated 60 min later. Isometric contractions increased (control: 0.546 ± 0.07 vs lead: 0.608 ± 0.06 g/mg) and time to peak tension decreased (control: 268 ± 13vs lead: 227 ± 5.58 ms), but relaxation time was unchanged. Post-pause potentiation was similar between groups (n = 6 per group), suggesting no change in sarcoplasmic reticulum activity, evaluated indirectly by this protocol. After 1-h exposure to lead acetate, the papillary muscles became hyperactive in response to a β-adrenergic agonist (10 µM isoproterenol). In addition, post-rest contractions decreased, suggesting a reduction in sarcolemmal calcium influx. The heart samples treated with 8 µM lead acetate presented increased Na+,K+-ATPase (approximately 140%, P < 0.05 for control vs lead) and myosin ATPase (approximately 30%, P < 0.05 for control vs lead) activity. Our results indicated that acute exposure to low lead concentrations produces direct positive inotropic and lusitropic effects on myocardial contractility and increases the right and left ventricular systolic pressure, thus potentially contributing to the early development of hypertension.

Exploring business models for medical games: Key components and challenges

The costs of health care are going up in many countries. In order to provide affordable and effective health care solutions, new technologies and approaches are constantly being developed. In this research, video games are presented as a possible solution to the problem. Video games are fun, and nowadays most people like to spend time on them. In addition, recent studies have pointed out that video games can have notable health benefits. Health games have already been developed, used in practice, and researched. However, the bulk of health game studies have been concerned with the design or the effectiveness of the games; no actual business studies have been conducted on the subject, even though health games often lack commercial success despite their health benefits. This thesis seeks to fill this gap. The specific aim of this thesis is to develop a conceptual business model framework and empirically use it in explorative medical game business model research. In the first stage of this research, a literature review was conducted and the existing literature analyzed and synthesized into a conceptual business model framework consisting of six dimensions. The motivation behind the synthesis is the ongoing ambiguity around the business model concept. In the second stage, 22 semi-structured interviews were conducted with different professionals within the value network for medical games. The business model framework was present in all stages of the empirical research: First, in the data collection stage, the framework acted as a guiding instrument, focusing the interview process. Then, the interviews were coded and analyzed using the framework as a structure. The results were then reported following the structure of the framework. In the results, the interviewees highlighted several important considerations and issues for medical games concerning the six dimensions of the business model framework. Based on the key findings of this research, several key components of business models for medical games were identified and illustrated in a single figure. Furthermore, five notable challenges for business models for medical games were presented, and possible solutions for the challenges were postulated. Theoretically, these findings provide pioneering information on the untouched subject of business models for medical games. Moreover, the conceptual business model framework and its use in the novel context of medical games provide a contribution to the business model literature. Regarding practice, this thesis further accentuates that medical games can offer notable benefits to several stakeholder groups and offers advice to companies seeking to commercialize these games.

Transference of lutein during cheese making, color stability, and sensory acceptance of prato cheese

The consumption of lutein is associated with the prevention and reduction of age-related macular degeneration. Its incorporation into Prato cheese as a yellowish food coloring is a valid alternative to increase the daily intake of this compound. However, part of the lutein added may be lost in the whey during the cheese making, or it can be degraded by light during storage, resulting in color changes reducing the sensory acceptance of the cheese. The objectives of this study were to determine the transference of the lutein (dye), added to the milk, in the whey, and cheese, to evaluate the effect of the lutein addition, light exposure, and storage time on the cheese color, and to verify the sensory acceptance of Prato cheese with addition of lutein. The lutein recovery of cheese was 95.25%. Color saturation (chrome) increased during storage time resulting in a cheese with more intense color, but there were no changes in the hue of the cheese. Adjusting the amount of lutein added to Prato cheese may lead to greater acceptance. The high recovery of lutein in the cheese and the fact that the hue remained unchanged during storage under light showed that the incorporation of lutein into Prato cheese is feasible from a technical point of view.

Production optimization and characterization of immunomodulatory peptides obtained from fermented goat placenta

The goat placental immunomodulatory peptides were produced by fermentation with Aspergillus Niger. The objective of the present study was to investigate the effects of fermentation parameters (carbon source content, pH, and time) on spleen lymphocyte proliferation for the highest immune activity of the fermentation broth using response surface methodology (RSM). According to the data analysis by the Design-Expert® software, the stimulation index value (23.51%), which is the maximum immune activity, was obtained under the following conditions: content of carbon source 1.97 g·L-1, initial pH 5.0, and 74.43 h of fermentation time. Under the optimized fermentation conditions, at a certain concentration range, the fermentation broth produced a significant effect on the proliferation of mouse spleen lymphocytes. Ultrafiltration technique was performed to separate the fermentation broth with different MW (molecular weight). It was found that peptides in the range of <10 KDa were the main bioactivity fractions for the immunomodulatory and antioxidant activities.

Man måste tänka själv : klasslärares uppfattningar av undervisning i de naturvetenskapliga läroämnena

A teacher´s perception of a school subject affects a teacher´s teaching and by extension pupils´ learning. The main purpose of this thesis is to describe the variation in the ways class-teachers perceive teaching within science subjects and to illustrate how these teachers choose to work and why they choose as they do. This purpose is operationalized into three central research questions concerning a teacher´s perception of teaching, teachers´ experiences of working methods in the subject and different aspects that are consciously present when the teacher makes his or her choice of working methods. These aspects are viewed from two different perspectives: a subject educational perspective and a teacher perspective. The theoretical background of the study is interdisciplinary. The thesis is a qualitative study where the research approach is phenomenographic. The empirical investigation was made as two separate studies: a semistructured interview study (N = 15) followed by a stimulated recall study (N = 3), a combined interview and video-observation. Results from the empirical investigation indicate that regarding aims for science education teachers wish to awaken or maintain the pupils´ interest in nature and science and that the pupils within the science subjects shall build a base for fundamental general knowledge. As motives for teaching the science subjects teachers view the subjects as a foundation for everyday life, planning and democracy but also for pupils´ further studies and a possible career in the field. The interdisciplinary key competences and the care for the pupils´ well being are aspects that are consciously present when teachers make their choice of working methods. A great variation can be found in the teachers´ perceptions of the science subjects as subjects and of the working methods within these subjects. Teachers describe lack of time on their own part as well as for the pupil´s learning. Results from the empirical investigation also indicate that teachers modestly focus on aims for the teaching and communication regarding these aims. There seems to be an existing need for increased and qualitatively improved inservice education within these subjects.

Natural freeze crystallization : purification of aqueous Na2SO4 solutions with cold air

The aim of this thesis was to examine efficiency of freeze crystallization and eutectic freeze crystallization in purification of wastewater by imitating natural freezing. In addition, a mathematic model based on heat transfer to determine ice thickness and ice growth rate was examined. Also, the amount of sodium sulfate crystallized at the eutectic point was under investigation. In literature part, advantages and applications of the freeze crystallization are discussed, and possibility to apply it in Northern hemisphere winter weather conditions is under study. Furthermore, main sources of sodium sulfate from Finnish industries are described. The experiments were carried out in modified chest freezer, where a fan was placed in order to obtain laminar air flow inside. Picolog PT-104 data logger was used to monitor temperature changes in the salt-water solution, and constant temperature was maintained in the crystallizer with Lauda RP 850 thermostat. The impurity of formed ice layer was determined by weighing ice samples after experiment and again after 24 hours drying to full dryness in oven. Volume of salt-water solution was also measured after experiment. The highest purity of formed ice layer was obtained with small temperature difference and with long freezing time. On the other hand, the amount of crystallized sodium sulfate was its greatest with long freezing time and higher temperature difference. The results obtained by the mathematic model and empirical results did not differ significantly in most of the experiments. However, the difference increased when salt-water mixture reached its eutectic point, leading to simultaneous ice and salt crystallization. Eutectic point was reached only with the highest salt concentration with one exception. In these cases, calculated values were in many cases greater than the experimental ones. In winter weather conditions freeze crystallization is cost-effective wastewater treatment method and rather simple. Nonetheless, the efficiency and separation rate are strongly depended on ambient temperature and its changes

A school-based cognitive behavior modification intervention strategy for learned helpless mentally retarded students

This study assessed the usefulness of a cognitive behavior modification (CBM) intervention package with mentally retarded students in overcoming learned helplessness and improving learning strategies. It also examined the feasibility of instructing teachers in the use of such a training program for a classroom setting. A modified single subject design across individuals was employed using two groups of three subjects. Three students from each of two segregated schools for the mentally retarded were selected using a teacher questionnaire and pupil checklist of the most learned helpless students enrolled there. Three additional learned helplessness assessments were conducted on each subject before and after the intervention in order to evaluate the usefulness of the program in alleviating learned helplessness. A classroom environment was created with the three students from each school engaged in three twenty minute work sessions a week with the experimenter and a tutor experimenter (TE) as instructors. Baseline measurements were established on seven targeted behaviors for each subject: task-relevant speech, task-irrelevant speech, speech denoting a positive evaluation of performance, speech denoting a negative evaluation of performance, proportion of time on task, non-verbal positive evaluation of performance and non-verbal negative evaluation of performance. The intervention package combined a variety of CBM techniques such as Meichenbaum's (1977) Stop, Look and Listen approach, role rehearsal and feedback. During the intervention each subject met with his TE twice a week for an individual half-hour session and one joint twenty minute session with all three students, the experimentor and one TE. Five weeks after the end of this experiment one follow up probe was conducted. All baseline, post-intervention and probe sessions were videotaped. The seven targeted behaviors were coded and comparisons of baseline, post intervention, and probe testing were presented in graph form. Results showed a reduction in learned helplessness in all subjects. Improvement was noted in each of the seven targeted behaviors for each of the six subjects. This study indicated that mentally retarded children can be taught to reduce learned helplessness with the aid of a CBM intervention package. It also showed that CBM is a viable approach in helping mentally retarded students acquire more effective learning strategies. Because the TEs (Tutor experimenters) had no trouble learning and implementing this program, it was considered feasible for teachers to use similar methods in the classroom.

Development and characterization of concentric capillary nebulizer used in inductively coupled plasma analysis /

A simple, low-cost concentric capillary nebulizer (CCN) was developed and evaluated for ICP spectrometry. The CCN could be operated at sample uptake rates of 0.050-1.00 ml min'^ and under oscillating and non-oscillating conditions. Aerosol characteristics for the CCN were studied using a laser Fraunhofter diffraction analyzer. Solvent transport efficiencies and transport rates, detection limits, and short- and long-term stabilities were evaluated for the CCN with a modified cyclonic spray chamber at different sample uptake rates. The Mg II (280.2nm)/l\/lg 1(285.2nm) ratio was used for matrix effect studies. Results were compared to those with conventional nebulizers, a cross-flow nebulizer with a Scott-type spray chamber, a GemCone nebulizer with a cyclonic spray chamber, and a Meinhard TR-30-K3 concentric nebulizer with a cyclonic spray chamber. Transport efficiencies of up to 57% were obtained for the CCN. For the elements tested, short- and long-term precisions and detection limits obtained with the CCN at 0.050-0.500 ml min'^ are similar to, or better than, those obtained on the same instrument using the conventional nebulizers (at 1.0 ml min'^). The depressive and enhancement effects of easily ionizable element Na, sulfuric acid, and dodecylamine surfactant on analyte signals with the CCN are similar to, or better than, those obtained with the conventional nebulizers. However, capillary clog was observed when the sample solution with high dissolved solids was nebulized for more than 40 min. The effects of data acquisition and data processing on detection limits were studied using inductively coupled plasma-atomic emission spectrometry. The study examined the effects of different detection limit approaches, the effects of data integration modes, the effects of regression modes, the effects of the standard concentration range and the number of standards, the effects of sample uptake rate, and the effect of Integration time. All the experiments followed the same protocols. Three detection limit approaches were examined, lUPAC method, the residual standard deviation (RSD), and the signal-to-background ratio and relative standard deviation of the background (SBR-RSDB). The study demonstrated that the different approaches, the integration modes, the regression methods, and the sample uptake rates can have an effect on detection limits. The study also showed that the different approaches give different detection limits and some methods (for example, RSD) are susceptible to the quality of calibration curves. Multicomponents spectral fitting (MSF) gave the best results among these three integration modes, peak height, peak area, and MSF. Weighted least squares method showed the ability to obtain better quality calibration curves. Although an effect of the number of standards on detection limits was not observed, multiple standards are recommended because they provide more reliable calibration curves. An increase of sample uptake rate and integration time could improve detection limits. However, an improvement with increased integration time on detection limits was not observed because the auto integration mode was used.

Responses to Reflection in Two Invertebrate Species

The present thesis investigates the responses to reflection in both the crayfish Procambarus clarkii and the fruit fly Drosophila melanogaster. Responses to reflection in crayfish depend on social status and the current work suggests that learning and memory consolidation are required for these responses to be altered. Crayfish were treated to either massed or spaced training fights prior to reflection testing. The results show that subordinate crayfish treated to spaced training display a response typical of subordinate crayfish but subordinate crayfish treated to massed training exhibit a response typical of dominant crayfish. Fruit flies are shown to be attracted to reflection and responses to reflection are described here for the first time. Responses in fruit flies are shown to be dependent on social status. The frequency of behaviours were altered in isolated flies but not socialized flies. The addition of pheromones cVA and 7,11-HD were used to investigate how the addition of chemical cues altered responses to reflection in fruit flies. Socialized fruit flies treated with cVA exhibited an increase in the frequency of behaviours on both mirrored and clear glass walls, while isolated flies exhibited a decrease. Socialized flies treated with 7,11-HD spent more time on mirrored walls compared to glass walls, whereas the frequency of all behaviours were decreased in isolated flies treated with 7,11-HD.

Percy Carruthers Band fonds, 1857-2005, n.d. (non-inclusive)

Percy Carruthers Band was born on November 27, 1892 in Toronto, Ontario to Charles Walter Band, a grain merchant and Jessie Camp Shaw Band. He graduated from Upper Canada College and became a broker. He worked at the Dominion Bank and then at Maple Leaf Milling Company. He was stationed at Port Colborne for a while. Before leaving for the front, he was with Bankers Bond Company of Toronto and is also listed as working with the firm of Bailey, Wood and Cross. Lieutenant Band received a Certificate of Military Qualifications on Dec. 24th, 1914. He received his Certificate of Military Instruction on Nov. 30, 1915. He received these certificates while with the 48th Regiment (Highlanders). He enlisted in 1914 and went overseas in August of 1915 as an officer in the 35th Battalion. By August 26, 1915, he is listed as being with the 23rd Reserve Battalion. A year later, in August of 1916 Lieutenant Band arrived in France and was posted to the 2nd Battalion – “The Second Iron”. In 1916, Band was the victim of shell shock received during a charge. He was wounded in April of 1917 at Vimy Ridge yet he remained on duty. At this time he received a gunshot wound to his right jaw. He earned a promotion to Captain on September 16th, 1917. He was wounded again in November of 1917 at Passchendaele where he suffered a gunshot wound to the ear. For his courage and determination Percy Band received the Military Cross on February 18, 1918. He led his company under difficult circumstances even though he was wounded. He was awarded a bar to the Military Cross for gallantry during a successful attack on two villages on December 2nd, 1918. During this attack he led his company against enemy machine guns. It is said that he displayed exceptional leadership qualities and skill during this time. On the 30th of August in 1918, he made a daring reconnaissance to the front under heavy fire in an attack on Upton Wood. He was also commended on his gallantry during attacks on Cagnicourt and the Canal du Nord in September of 1918. He was awarded the second bar to the Military Cross on February 1, 1919. The award of the Croix de Guerre was conferred on Captain Percy Carruthers Band by the President of the French Republic on December 15th, 1918 for distinguished service rendered during the course of the campaign. His general demobilization took place on April 25, 1919. Percy Band married Margaret Julia Woodruff on November 25, 1919, and they had three children: Charles Woodruff Band (1921), Margaret Elizabeth Band (1924) and Robert DeVeaux Woodruff Band (1927). After the war, Mr. Band was a manager at Geo. Weston Bread and Cakes Limited, St. Catharines. Percy Band was also an avid collector. His collections included antique toys and art. He died suddenly on May 19, 1961. The Toronto Telegram published this about him: “Captain Percy Carruthers Band, M.C. with two Bars, Croix de Guerre with Palm – was an officer whose buoyant spirit and gallantry mirrored the vibrant soul of the Battalion. Blythe of heart, yet endowed with a fine sense of responsibility, he gave inspired leadership of No. 3 Company.”

Calibration de systèmes de caméras et projecteurs dans des applications de création multimédia

Ce mémoire s'intéresse à la vision par ordinateur appliquée à des projets d'art technologique. Le sujet traité est la calibration de systèmes de caméras et de projecteurs dans des applications de suivi et de reconstruction 3D en arts visuels et en art performatif. Le mémoire s'articule autour de deux collaborations avec les artistes québécois Daniel Danis et Nicolas Reeves. La géométrie projective et les méthodes de calibration classiques telles que la calibration planaire et la calibration par géométrie épipolaire sont présentées pour introduire les techniques utilisées dans ces deux projets. La collaboration avec Nicolas Reeves consiste à calibrer un système caméra-projecteur sur tête robotisée pour projeter des vidéos en temps réel sur des écrans cubiques mobiles. En plus d'appliquer des méthodes de calibration classiques, nous proposons une nouvelle technique de calibration de la pose d'une caméra sur tête robotisée. Cette technique utilise des plans elliptiques générés par l'observation d'un seul point dans le monde pour déterminer la pose de la caméra par rapport au centre de rotation de la tête robotisée. Le projet avec le metteur en scène Daniel Danis aborde les techniques de calibration de systèmes multi-caméras. Pour son projet de théâtre, nous avons développé un algorithme de calibration d'un réseau de caméras wiimotes. Cette technique basée sur la géométrie épipolaire permet de faire de la reconstruction 3D d'une trajectoire dans un grand volume à un coût minime. Les résultats des techniques de calibration développées sont présentés, de même que leur utilisation dans des contextes réels de performance devant public.

Investigation of femtosecond laser technology for the fabrication of drug nanocrystals in suspension

La technique du laser femtoseconde (fs) a été précédemment utilisée pour la production de nanoparticules d'or dans un environnement aqueux biologiquement compatible. Au cours de ce travail de maîtrise, cette méthode a été investiguée en vue d'une application pour la fabrication de nanocristaux de médicament en utilisant le paclitaxel comme modèle. Deux procédés distincts de cette technologie à savoir l'ablation et la fragmentation ont été étudiés. L'influence de la puissance du laser, de point de focalisation, et de la durée du traitement sur la distribution de taille des particules obtenues ainsi que leur intégrité chimique a été évaluée. Les paramètres ont ainsi été optimisés pour la fabrication des nanoparticules. L’évaluation morphologique et chimique a été réalisée par microscopie électronique et spectroscopie infrarouge respectivement. L'état cristallin des nanoparticules de paclitaxel a été caractérisé par calorimétrie differentielle et diffraction des rayons X. L'optimisation du procédé de production de nanoparticules par laser fs a permis d'obtenir des nanocristaux de taille moyenne (400 nm, polydispersité ≤ 0,3). Cependant une dégradation non négligeable a été observée. La cristallinité du médicament a été maintenue durant la procédure de réduction de taille, mais le paclitaxel anhydre a été transformé en une forme hydratée. Les résultats de cette étude suggèrent que le laser fs peut générer des nanocristaux de principe actif. Cependant cette technique peut se révéler problématique pour des médicaments sensibles à la dégradation. Grâce à sa facilité d'utilisation et la possibilité de travailler avec des quantités restreintes de produit, le laser fs pourrait représenter une alternative valable pour la production de nanoparticules de médicaments peu solubles lors des phases initiales de développement préclinique. Mots-clés: paclitaxel, nanocristaux, laser femtoseconde, ablation, fragmentation