Fabrication and characterization of silicon position sensitive particle detectors

Position sensitive particle detectors are needed in high energy physics research. This thesis describes the development of fabrication processes and characterization techniques of silicon microstrip detectors used in the work for searching elementary particles in the European center for nuclear research, CERN. The detectors give an electrical signal along the particles trajectory after a collision in the particle accelerator. The trajectories give information about the nature of the particle in the struggle to reveal the structure of the matter and the universe. Detectors made of semiconductors have a better position resolution than conventional wire chamber detectors. Silicon semiconductor is overwhelmingly used as a detector material because of its cheapness and standard usage in integrated circuit industry. After a short spread sheet analysis of the basic building block of radiation detectors, the pn junction, the operation of a silicon radiation detector is discussed in general. The microstrip detector is then introduced and the detailed structure of a double-sided ac-coupled strip detector revealed. The fabrication aspects of strip detectors are discussedstarting from the process development and general principles ending up to the description of the double-sided ac-coupled strip detector process. Recombination and generation lifetime measurements in radiation detectors are discussed shortly. The results of electrical tests, ie. measuring the leakage currents and bias resistors, are displayed. The beam test setups and the results, the signal to noise ratio and the position accuracy, are then described. It was found out in earlier research that a heavy irradiation changes the properties of radiation detectors dramatically. A scanning electron microscope method was developed to measure the electric potential and field inside irradiated detectorsto see how a high radiation fluence changes them. The method and the most important results are discussed shortly.

Mikroliuskarakenteisen T-resonaattorin käyttö piirilevyn eristeominaisuuksien määrityksessä

Tässä diplomityössä tutkittiin ja kehitettiin edelleen mikroliuskarakenteisen T-resonaattorin käyttöä laajakaistaisessa piirilevylaminaattien dielektrisyysvakion ja häviökertoimen määrityksessä. Työssä perehdyttiin eristeominaisuuksien määrityksessä tarvittaviin laskentamenetelmiin sekä T-resonaattorin toimintaan. T-resonaattorin suunnittelu ja käyttöä varten valitut laskentamenetelmät on esitelty. Työssä suunniteltiin ja valmistettiin mikroliuskarakenteinen T-resonaattorimittausrakenne, jolla määritettiin erään FR-4 -tyyppisen piirilevylaminaattimateriaalin dielektrisyysvakio sekä häviökerroin mittausten ja laskennan avulla taajuuskaistalla 0,5 - 10 GHz. Tuloksia verrattiin muilla käytössä olevilla menetelmillä määritettyihin tuloksiin. Tulosten perusteella voitiin osoittaa, että mikroliuskarakenteinen T-resonaattori soveltuu hyvin piirilevylaminaattien eristeominaisuuksien määritykseen, ja käytetyt laskenta-menetelmät antavat realistisia tuloksia.

Kalibrointimenetelmä planaaristen siirtojohtojen mittaamiseen

Tässä diplomityössä tutkittiin TRL-kalibroinnin käyttämistä tasomaisten siirtojohtojen sähköisten parametrien määrittämisessä taajuusalueella 0,3 – 12 GHz. Työssä perehdyttiin TRL-kalibroinnin käyttämiseen piirianalysaattorilla toteutettujen mittauksien mittauskalibrointiin sekä kalibrointiin tarvittavien kalibrointistandardien mitoittamiseen. Kalibrointistandardit suunniteltiin ja toteutettiin sekä mikroliuska- että liuskajohdoille, joiden toiminnallisuutta tarkasteltiin sekä taajuustason että aikatason mittausten avulla. Työssä perehdyttiin myös kalibrointistandardien liityntärajapinnan suunniteluun ja toteuttamiseen. Saatujen tulosten perusteella voitiin osoittaa mikroliuskajohtokitin soveltuvan hyvin mittauskalibroinnin toteuttamiseen tarkoissa mittaussovelluksissa.

Johdinhäviöiden määrittäminen mikroliuskarakenteessa

Tässä diplomityössä on käsitelty mikroliuskarakenteen johdinhäviöiden määrittämistä kokeellisin ja analyyttisin menetelmin. Työssä on käyty läpi mikroliuskarakenteen ominaisuudet sekä esitetty tärkeimmät kirjallisuudessa esitellyt menetelmät johdinhäviöiden laskemiseksi. Mikroliuskarakenteen häviöitä mallinnettiin modernilla momenttimenetelmään perustuvalla kenttälaskentasimulaattorilla. Simulaattorin toimintaperiaate on esitelty ja sen soveltaminen mikroliuskarakenteen simuloimiseen on käyty läpi. Eräs mikroliuskarakenne mallinnettiin taajuusalueella 1-10 GHz ja simuloituja johdinhäviöitä verrattiin analyyttisesti määritettyihin. Mikroliuskarakenteen vaste mitattiin ja sitä verrattiin mallinnetun mikroliuskarakenteen vasteeseen. Tulosten perusteella on pohdittu simulaattorin soveltuvuutta mikroliuskarakenteen johdinhäviöiden mallintamiseen. Mikroliuskarakenteen johdinhäviöiden määrittämiseen mittausten avulla on esitetty ideoita jatkotutkimusta varten.

Antennimittausjärjestelmän toteutus ja ominaisuuksien määrittäminen

Diplomityössä tarkasteltiin antennien säteilykuviomittauksiin käytettävien antennimittaratojen ominaisuuksia. Sovelletun elektroniikan laboratorion antennimittaradasta kehitettiin toimiva säteilykuvion mittausjärjestelmä, johon kuuluvat radiokaiuton kammio, suuntauskoneisto ja antennikannakkeet, HP 8720D -piirianalysaattori ja RF-kaapelointi sekä valmistutetut mitta-antennitorvet. Työssä vertailtiin koaksiaalikaapeleita ja valittiin antennimittaukseen soveltuvat. 1,70–2,60 GHz:n taajuusalueen mittastandardiksi suunniteltiin torviantenni, jonka kaksi prototyyppiä valmistutettiin konetekniikan osastolla. Torviantennien ominaisuudet mitattiin. Antennimittaradan ominaisuudet ja soveltuvuus erilaisiin antennimittauksiin selvitettiin sekä teoreettisesti että mittauksin.

Microwave spectrometry for the Evaluation of the structural integrity of metallic stents

Purpose: To assess the feasibility of a method based on microwave spectrometry to detect structural distortions of metallic stents in open air conditions and envisage the prospects of this approach toward possible medical applicability for the evaluation of implanted stents. Methods: Microwave absorbance spectra between 2.0 and 18.0 GHz were acquired in open air for the characterization of a set of commercial stents using a specifically design setup. Rotating each sample over 360º, 2D absorbance diagrams were generated as a function of frequency and rotation angle. To check our approach for detecting changes in stent length (fracture) and diameter (recoil), two specific tests were performed in open air. Finally, with a few adjustments, this same system provides 2D absorbance diagrams of stents immersed in a water-based phantom, this time over a bandwidth ranging from 0.2 to 1.8 GHz. Results: The authors show that metallic stents exhibit characteristic resonant frequencies in their microwave absorbance spectra in open air which depend on their length and, as a result, may reflect the occurrence of structural distortions. These resonances can be understood considering that such devices behave like dipole antennas in terms of microwave scattering. From fracture tests, the authors infer that microwave spectrometry provides signs of presence of Type I to Type IV stent fractures and allows in particular a quantitative evaluation of Type III and Type IV fractures. Recoil tests show that microwave spectrometry seems able to provide some quantitative assessment of diametrical shrinkage, but only if it involves longitudinal shortening. Finally, the authors observe that the resonant frequencies of stents placed inside the phantom shift down with respect to the corresponding open air frequencies, as it should be expected considering the increase of dielectric permittivity from air to water. Conclusions: The evaluation of stent resonant frequencies provided by microwave spectrometry allows detection and some quantitative assessment of stent fracture and recoil in open air conditions. Resonances of stents immersed in water can be also detected and their characteristic frequencies are in good agreement with theoretical estimates. Although these are promising results, further verifica tion in a more relevant phantom is required in order to foresee the real potential of this approach.

Architectural characterization of a delta-front reservoir analogue combining ground penetrating radar and electrical resistivity tomography: Roda Sandstone (Lower Eocene, Graus-Tremp basin, Spain)

Three-dimensional reconstruction of reservoir analogues can be improved combining data from different geophysical methods. Ground Penetrating Radar (GPR) and Electrical Resistivity Tomography (ERT) data are valuable tools, since they provide subsurface information from internal architecture and facies distribution of sedimentary rock bodies, enabling the upgrading of depositional models and heterogeneity reconstruction. The Lower Eocene Roda Sandstone is a well-known deltaic complex widely studied as a reservoir analogue that displays a series of sandstone wedges with a general NE to SW progradational trend. To provide a better understanding of internal heterogeneity of a 10m-thick progradational delta-front sandstone unit, 3D GPR data were acquired. In addition, common midpoints (CMP) to measure the sandstone subsoil velocity, test profiles with different frequency antennas (25, 50 and 100MHz) and topographic data for subsequent correction in the geophysical data were also obtained. Three ERT profiles were also acquired to further constrain GPR analysis. These geophysical results illustrate the geometry of reservoir analogue heterogeneities both depositional and diagenetic in nature, improving and complementing previous outcrop-derived data. GPR interpretation using radar stratigraphy principles and attributes analysis provided: 1)tridimensional geometry of major stratigraphic surfaces that define four units in the GPR Prism, 2) image the internal architecture of the units and their statistical study of azimuth and dips, useful for a quick determination of paleocurrent directions. These results were used to define the depositional architecture of the progradational sandbody that shows an arrangement in very-high-frequency sequences characterized by clockwise paleocurrent variations and decrease of the sedimentary flow, similar to those observed at a greater scale in the same system. This high-frequency sequential arrangement has been attributed to the autocyclic dynamics of a supply-dominated delta- front where fluvial and tidal currents are in competition. The resistivity models enhanced the viewing of reservoir quality associated with cement distribution caused by depositional and early diagenetic processes related to the development of transgressive and regressive systems tracts in igh-frequency sequences.

Nanoantenna enhanced emission of lightharvesting complex 2: the role of resonance, polarization, and radiative and non-radiative rates

Nanoantennae show potential for photosynthesis research for two reasons; first by spatially confining light for experiments which require high spatial resolution, and second by enhancing the photon emission of single light-harvesting complexes. For effective use of nanoantennae a detailed understanding of the interaction between the nanoantenna and the light-harvesting complex is required. Here we report how the excitation and emission of multiple purple bacterial LH2s (light-harvesting complex 2) are controlled by single gold nanorod antennae. LH2 complexes were chemically attached to such antennae, and the antenna length was systematically varied to tune the resonance with respect to the LH2 absorption and emission. There are three main findings. (i) The polarization of the LH2 emission is fully controlled by the resonant nanoantenna. (ii) The largest fluorescence enhancement, of 23 times, is reached for excitation with light at λ = 850 nm, polarized along the long antenna-axis of the resonant antenna. The excitation enhancement is found to be 6 times, while the emission efficiency is increased 3.6 times. (iii) The fluorescence lifetime of LH2 depends strongly on the antenna length, with shortest lifetimes of [similar]40 ps for the resonant antenna. The lifetime shortening arises from an 11 times resonant enhancement of the radiative rate, together with a 2–3 times increase of the non-radiative rate, compared to the off-resonant antenna. The observed length dependence of radiative and non-radiative rate enhancement is in good agreement with simulations. Overall this work gives a complete picture of how the excitation and emission of multi-pigment light-harvesting complexes are influenced by a dipole nanoantenna.

DFM(A)- aspects for a horn antenna design

In this paper aspects of design for manufacturability and assembly (DFMA) are applied to the design of coaxially fed standard gain horn antenna for 1.70 - 2.60 GHz. Possibilities to utilize cross-technological approach method is examined. Methods of DFMA for laser processing are covered and practical design guides and methods are developed. Antenna construction for easy manufacturing and specialized performance is shown. Required dimensions and tolerances are discussed and suitable materials for laser processing are selected.

Disseny pràctic d'un transmissor d'àudio complert utilitzant una modulació AM

Un transmissor d’AM (modulació per amplitud), utilitza una de les moltes tècniques de modulació existents avui en dia. És molta la importància que té la modulació de senyals i aquests en són alguns exemples: -Facilita la propagació del senyal per cable o per aire. -Ordena l’espectre, distribuint Canals a les diferents informacions. -Disminueix la dimensió de les antenes. -Optimitza l’ample de banda de cada canal. -Evita interferències entre Canals. -Protegeix la informació de les degradacions per soroll. -Defineix la qualitat de la informació transmesa. L’objectiu principal d’aquest treball, serà realitzar un transmissor d’AM utilitzant components electrònics disponibles al mercat. Això es realitzarà mitjançant diversos procediments de disseny. Es realitzarà un procediment de disseny teòric, tot utilitzant els “datasheets” dels diferents components. Es realitzarà un procediment de disseny mitjançant la simulació, gràcies al qual es podrà provar el disseny del dispositiu i realitzar-ne algunes parts impossibles a reproduir teòricament. I finalment es realitzarà el dispositiu a la pràctica. Entre les conclusions més rellevants obtingudes en aquest treball, voldríem destacar la importància de la simulació per poder dissenyar circuits de radiofreqüència. En aquest treball s’ha demostrat que gràcies a una bona simulació, el primer prototip de dispositiu creat ens ha funcionat a la perfecció. D’altre banda, també comentar la importància d’un disseny adequat d’antena per poder aprofitar al màxim el rendiment del nostre dispositiu. Per concloure, la realització d’un aparell transmissor aporta unes nocions equilibrades d’electrònica i telecomunicacions importants per al disseny de dispositius de comunicació.

ZigBee-verkot ja evaluointilaitteen suunnittelu

In this thesis a closer look at ZigBee wireless network protocol was made and a ZigBee evaluation device was designed and built for testing it. ZigBee is a digital wireless network technology published in 2004, which was developed for wireless control and automation systems. It is based on the IEEE 802.15.4-2003 standard, and its aim was to create a reliable wireless networking protocol with secure data transmissions, low power consumption and low manufacturing costs. The low power consumption requirement has also led to a slow data rate and a short range, but in a ZigBee network individual network devices can route messages to each other, so short range is not a problem. In automation and control systems a fast data rate is not usually an important requirement either. ZigBee network can form automatically and one ZigBee network can theoretically include thousands of devices, all of which can communicate with each other. ZigBee network is also self-healing, so an individual device dropping out of the network, like breaking down, does not affect functionality of the network. Evaluation device was designed and implemented in four different versions, which were tested with six different antenna designs. All antennas were tested at a range of 100 meters in an open terrain using two different frequencies and transmission powers. Also a range test was performed for selected antennas using transmission power of 4,5 dBm, which was maximum power of the ZigBee chip used in the evaluation device. Range test resulted in a measured range of several hundred meters, which can be considered as a good result for a short-range technology.

LTE tulevaisuuden mobiiliverkkoratkaisuna

Tässä kandidaatintyössä käytiin läpi kuinka LTE soveltuu tulevaisuuden mobiiliverkkoratkaisuksi. Ensiksi selvitettiin sen kehityshistoriaa ja vaatimuksia. Seuraavaksi käytiin läpi LTE:n teknistä puolta, kuten radiotekniikkaa, taajuusjakoa ja antenneja. Työssä tehtiin katsaus myös uuteen SAE verkkoarkkitehtuuriin. Teknillisen puolen jälkeen työssä käytiin läpi LTE:n kilpailijoita, sekä tutustuttiin tarkemmin sen pahimpaan haastajaan WiMAX:iin. Näiden kahden tekniikan välillä tehtiin myös vertailu. Lopuksi katsottiin tulevaisuuden trendejä ja mobiilin datasiirron kehittymistä sekä tutustuttiin LTE:n seuraavaan versioon LTE-Advanced:iin.

Thermal Stress in a Roll-to-Roll Printed Electronics Substrate

The Roll-to-Roll process makes it possible to print electronic products continuously onto a uniform substrate. Printing components on flexible surfaces can bring down the costs of simple electronic devices such as RFID tags, antennas and transistors. The possibility of quickly printing flexible electronic components opens up a wide array of novel products previously too expensive to produce on a large scale. Several different printing methods can be used in Roll-to-Roll printing, such as gravure, spray, offset, flexographic and others. Most of the methods can also be mixed in one production line. Most of them still require years of research to reach a significant commercial level. The research for this thesis was carried out at the Konkuk University Flexible Display Research Center (KU-FDRC) in Seoul, Korea. A system using Roll-to-Roll printing requires that the motion of the web can be controlled in every direction in order to align different layers of ink properly. Between printers the ink is dried with hot air. The effects of thermal expansion on the tension of the web are studied in this work, and a mathematical model was constructed on Matlab and Simulink. Simulations and experiments lead to the conclusion that the thermal expansion of the web has a great influence on the tension of the web. Also, experimental evidence was gained that the particular printing machine used for these experiments at KU-FDRC may have a problem in controlling the speeds of the cylinders which pull the web.

Radar cross-section measurement using the Doppler effect

In this Master Thesis we discuss issues related to the measurement of the effective scattering surface, based on the Doppler Effect. Modeling of the detected signal was made. Narrowband signal filtering using low-frequency amplifier was observed. Parameters of the proposed horn antennas were studied; radar cross section charts for three different objects were received.

Antenna feed design for omnidirectional broadband antenna

This thesis is about development broadband feed for two-mirror antenna system that match following requirements: beamwidth from 45 to 90 degrees at -3 dB level, circular polarization, absence of radiation to the lower hemisphere area. Literature review was done in the areas of the UWB antennas creation. During the work attempts were made to create a feed in a form of the quad ridged horn and "eleven" antennas. The latter is introduced as the most effective feed among all antennas discussed in thesis. Radiation patterns and other results for "eleven" antenna were obtained. Results were saved as far field sources and placed slightly below focal point into the two-mirror antenna system, because phase center of the “eleven” antenna is predominantly shifted upwards. Directivity patterns for the two-mirror system were obtained and the conclusions about the work results have been made