Static and dynamic contact angle measurement on rough surfaces using sessile drop profile analysis with application to water management in low temperature fuel cells

Fuel Cells are a promising alternative energy technology. One of the biggest problems that exists in fuel cell is that of water management. A better understanding of wettability characteristics in the fuel cells is needed to alleviate the problem of water management. Contact angle data on gas diffusion layers (GDL) of the fuel cells can be used to characterize the wettability of GDL in fuel cells. A contact angle measurement program has been developed to measure the contact angle of sessile drops from drop images. Digitization of drop images induces pixel errors in the contact angle measurement process. The resulting uncertainty in contact angle measurement has been analyzed. An experimental apparatus has been developed for contact angle measurements at different temperature, with the feature to measure advancing and receding contact angles on gas diffusion layers of fuel cells.

Structural and surface property characterization of titanium dioxide nanotubes for orthopedic implants

This research focused on the to modification of the surface structure of titanium implants with nanostructured morphology of TiO2 nanotubes and studied the interaction of nanotubes with osteoblast cells to understand the parameters that affect the cell growth. The electrical, mechanical, and structural properties of TiO2 nanotubes were characterized to establish a better understanding on the properties of such nanoscale morphological structures. To achieve the objectives of this research work I transformed the titanium and its alloys, either in bulk sheet form, bulk machined form, or thin film deposited on another substrate into a surface of titania nanotubes using a low cost and environmentally friendly process. The process requires only a simple electrolyte, low cost electrode, and a DC power supply. With this simple approach of scalable nanofabrication, a typical result is nanotubes that are each approximately 100nm in diameter and have a wall thickness of about 20nm. By changing the fabrication parameters, independent nanotubes can be fabricated with open volume between them. Titanium in this form is termed onedimensional since electron transport is narrowly confined along the length of the nanotube. My Ph.D. accomplishments have successfully shown that osteoblast cells, the cells that are the precursors to bone, have a strong tendency to attach to the inside and outside of the titanium nanotubes onto which they are grown using their filopodia – cell’s foot used for locomotion – anchored to titanium nanotubes. In fact it was shown that the cell prefers to find many anchoring sites. These sites are critical for cell locomotion during the first several weeks of maturity and upon calcification as a strongly anchored bone cell. In addition I have shown that such a surface has a greater cell density than a smooth titanium surface. My work also developed a process that uses a focused and controllably rastered ion beam as a nano-scalpel to cut away sections of the osteoblast cells to probe the attachment beneath the main cell body. Ultimately the more rapid growth of osteoblasts, coupled with a stronger cell-surface interface, could provide cost reduction, shorter rehabilitation, and fewer follow-on surgeries due to implant loosening.

DESIGN AND FABRICATION OF RESONANT GAS SENSOR FOR HIGH SENSITIVITY IN THE PRESENCE OF AIR DAMPING

Gas sensors have been used widely in different important area including industrial control, environmental monitoring, counter-terrorism and chemical production. Micro-fabrication offers a promising way to achieve sensitive and inexpensive gas sensors. Over the years, various MEMS gas sensors have been investigated and fabricated. One significant type of MEMS gas sensors is based on mass change detection and the integration with specific polymer. This dissertation aims to make contributions to the design and fabrication of MEMS resonant mass sensors with capacitance actuation and sensing that lead to improved sensitivity. To accomplish this goal, the research has several objectives: (1) Define an effective measure for evaluating the sensitivity of resonant mass devices; (2) Model the effects of air damping on microcantilevers and validate models using laser measurement system (3) Develop design guidelines for improving sensitivity in the presence of air damping; (4) Characterize the degree of uncertainty in performance arising from fabrication variation for one or more process sequences, and establish design guidelines for improved robustness. Work has been completed toward these objectives. An evaluation measure has been developed and compared to an RMS based measure. Analytic models of air damping for parallel plate that include holes are compared with a COMSOL model. The models have been used to identify cantilever design parameters that maximize sensitivity. Additional designs have been modeled with COMSOL and the development of an analytical model for Fixed-free cantilever geometries with holes has been developed. Two process flows have been implemented and compared. A number of cantilever designs have been fabricated and the uncertainty in process has been investigated. Variability from processing have been evaluated and characterized.

Wetting and Reactive Air Brazing of BSCF for Oxygen Separation Devices

The goals of this project are to develop a Reactive Air Brazing (RAB) alloy and process for joining Barium strontium cobalt ferrite (BSCF), and to develop a fundamental understanding of the wettability and microstructral development due to reaction kinetics in BSCF/Ag-MexOy systems.

Assessments and Computational Simulations in Support of a Time-Varying Mass Flow Rate Measurement Technique for Pulsatile Gas Flow

This thesis covers the correction, and verification, development, and implementation of a computational fluid dynamics (CFD) model for an orifice plate meter. Past results were corrected and further expanded on with compressibility effects of acoustic waves being taken into account. One dynamic pressure difference transducer measures the time-varying differential pressure across the orifice meter. A dynamic absolute pressure measurement is also taken at the inlet of the orifice meter, along with a suitable temperature measurement of the mean flow gas. Together these three measurements allow for an incompressible CFD simulation (using a well-tested and robust model) for the cross-section independent time-varying mass flow rate through the orifice meter. The mean value of this incompressible mass flow rate is then corrected to match the mean of the measured flow rate( obtained from a Coriolis meter located up stream of the orifice meter). Even with the mean and compressibility corrections, significant differences in the measured mass flow rates at two orifice meters in a common flow stream were observed. This means that the compressibility effects associated with pulsatile gas flows is significant in the measurement of the time-varying mass flow rate. Future work (with the approach and initial runs covered here) will provide an indirect verification of the reported mass flow rate measurements.

Casting materials and their application in research and teaching

From a biological point of view, casting refers to filling of anatomical and/or pathological spaces with extraneous material that reproduces a three-dimensional replica of the space. Casting may be accompanied by additional procedures such as corrosion, in which the soft tissue is digested out, leaving a clean cast, or the material may be mixed with radiopaque substances to allow x-ray photography or micro computed topography (µCT) scanning. Alternatively, clearing of the surrounding soft tissue increases transparency and allows visualization of the casted cavities. Combination of casting with tissue fixation allows anatomical dissection and didactic surgical procedures on the tissue. Casting materials fall into three categories namely, aqueous substances (India ink, Prussian blue ink), pliable materials (gelatins, latex, and silicone rubber), or hard materials (methyl methacrylates, polyurethanes, polyesters, and epoxy resins). Casting has proved invaluable in both teaching and research and many phenomenal biological processes have been discovered through casting. The choice of a particular material depends inter alia on the targeted use and the intended subsequent investigative procedures, such as dissection, microscopy, or µCT. The casting material needs to be pliable where anatomical and surgical manipulations are intended, and capillary-passable for ultrastructural investigations.

Loss to follow-up of HIV-infected women after delivery: The Swiss HIV Cohort Study and the Swiss Mother and Child HIV Cohort Study.

INTRODUCTION HIV-infected pregnant women are very likely to engage in HIV medical care to prevent transmission of HIV to their newborn. After delivery, however, childcare and competing commitments might lead to disengagement from HIV care. The aim of this study was to quantify loss to follow-up (LTFU) from HIV care after delivery and to identify risk factors for LTFU. METHODS We used data on 719 pregnancies within the Swiss HIV Cohort Study from 1996 to 2012 and with information on follow-up visits available. Two LTFU events were defined: no clinical visit for >180 days and no visit for >360 days in the year after delivery. Logistic regression analysis was used to identify risk factors for a LTFU event after delivery. RESULTS Median maternal age at delivery was 32 years (IQR 28-36), 357 (49%) women were black, 280 (39%) white, 56 (8%) Asian and 4% other ethnicities. One hundred and seven (15%) women reported any history of IDU. The majority (524, 73%) of women received their HIV diagnosis before pregnancy, most of those (413, 79%) had lived with diagnosed HIV longer than three years and two-thirds (342, 65%) were already on antiretroviral therapy (ART) at time of conception. Of the 181 women diagnosed during pregnancy by a screening test, 80 (44%) were diagnosed in the first trimester, 67 (37%) in the second and 34 (19%) in the third trimester. Of 357 (69%) women who had been seen in HIV medical care during three months before conception, 93% achieved an undetectable HIV viral load (VL) at delivery. Of 62 (12%) women with the last medical visit more than six months before conception, only 72% achieved an undetectable VL (p=0.001). Overall, 247 (34%) women were LTFU over 180 days in the year after delivery and 86 (12%) women were LTFU over 360 days with 43 (50%) of those women returning. Being LTFU for 180 days was significantly associated with history of intravenous drug use (aOR 1.73, 95% CI 1.09-2.77, p=0.021) and not achieving an undetectable VL at delivery (aOR 1.79, 95% CI 1.03-3.11, p=0.040) after adjusting for maternal age, ethnicity, time of HIV diagnosis and being on ART at conception. CONCLUSIONS Women with a history of IDU and women with a detectable VL at delivery were more likely to be LTFU after delivery. This is of concern regarding their own health, as well as risk for sexual partners and subsequent pregnancies. Further strategies should be developed to enhance retention in medical care beyond pregnancy.

Is clipping the preferable technique to perform sympathicotomy? A retrospective study and review of the literature

PURPOSE Thoracoscopic sympathetic surgery is nowadays a broadly accepted technique in the treatment of primary hyperhidrosis as well as facial blushing. The objective of this study was to compare the two currently most commonly used methods for thoracic sympathicotomy: transection (ETS) and clipping (ETC.). METHODS This is a retrospective study on a total of 63 patients, who underwent rib-oriented sympathicotomy, either by transection (n = 36, 57 %) or by clipping (n = 27, 43 %). Moreover, the up-to-date international literature is reviewed concerning which level(s) of the sympathetic trunk should be addressed, depending on the patients underlying condition. Furthermore, the highly controversial topic of reversibility of sympathetic clipping is debated. RESULTS Our results confirm that clipping is at least as effective as transection of the sympathetic chain in the treatment of hyperhidrosis and facial blushing. Furthermore, the analysis of all larger studies on unclipping in humans shows a surprisingly high reported reversal rate between 48 and 77 %. CONCLUSIONS Depending on the symptoms of the patient, different levels of the sympathetic chain should be addressed. When a higher rib level such as R2 is approached, which more likely will result in moderate to severe compensatory sweating, clipping should be preferred as it seems that this technique has indeed a potential for reversibility. As demonstrated, this method is at least as effective as an irreversible transection of the sympathetic chain.