Four-leg converters with improved common current sharing and selective voltage-quality enhancement for islanded microgrids

Four-leg dc-ac power converters are widely used for the power grids to manage grid voltage unbalance caused by the interconnection of single-phase or three-phase unbalanced loads. These converters can further be connected in parallel to increase the overall power rating. The control of these converters poses a particular challenge if they are placed far apart with no links between them (e.g., in islanded microgrids). This challenge is studied in this paper with each four-leg converter designed to have improved common current sharing and selective voltage-quality enhancement. The common current sharing, including zero sequence component, is necessary since loads are spread over the microgrid and they are hence the common responsibility of all converters. The voltage-quality enhancement consideration should however be more selective since different loads have different sensitivity levels towards voltage disturbances. Converters connected to the more sensitive load buses should therefore be selectively triggered for compensation when voltage unbalances at their protected buses exceed the predefined thresholds. The proposed scheme is therefore different from conventional centralized schemes protecting only a common bus. Simulation and experimental results obtained have verified the effectiveness of the proposed scheme when applied to a four-wire islanded microgrid.

A gabonaszállítási piac színe és visszája Magyarországon (The pros and contras of the Hungarian cereals transportation market)

A tanulmány a szakirodalomban újszerű kezdeményezésként kísérletet tesz a gabonapiac ellátási láncának felrajzolására, majd annak egyik, a cikk alapkérdése szempontjából kiemelt vetületét, a gabonaszállítási és raktározási problémákat elemzi. Előbbit a piac szereplőitől kvalitatív módon begyűjtött információkkal, utóbbit a szakirodalom alapján mutatja be. A cikk az elemzés után javaslatokkal szolgál ahhoz, hogyan lehetne hazánkban egy integrált gabonapiaci szállítási-raktározási-átrakási rendszert kialakítani. __________ The aim of the article is to present the situation of the Hungarian cereals transport and storage-reloading market and by interconnection, to treat cereals market’s operations systemically. Under this process, the study trace to draw a possible supply chain of the national cereals market up, which is a new initiation in the Hungarian literature. The focus of the article is to analyse transport and storage processes in the cereals market using the framework mentioned above. Transport market is demonstrated on the grounds of a revealing qualitative research, while storage market is brought out by literature. After analysis, the article gives recommendations how to shape an integrated transport and storage-reload system in the Hungarian cereals market.

Interactive foresight on the Hungarian SMEs

Purpose – The aim of this study is to present a concept of interactive foresight process, its theoretical and methodological considerations and a foresight exercise concerning the development of knowledge economy in the Central Hungarian Region. Design/methodology/approach – A methodology of interactive foresight process for creating regional future concepts is developed, which is based on a specific meaning of integral futures and uses online solutions, too. Findings – Personal meetings with small and medium enterprise (SME) stakeholders and the works of interactive communications with feedbacks within and among stakeholder groups was organized around the research homepage. The networking created the interconnection and the feedbacks between the stakeholders and the futurist group in the process of shaping regional future ideas. The online networking is running. Research limitations/implications – The low number of stakeholders can limit the validity and acceptance of futures ideas created by this process. Practical implications – The developed interactive foresight process can also be applicable at different organizational levels and in different fields for shaping shared future ideas. Social implications – Application of interactive foresight process can contribute to the development of anticipatory democracy. Originality/value – A theoretically based interactive foresight process has been developed in which stakeholders can participate not only interactively in the foresight process but they can implement the achievements in their enterprising activity as well. The participants were interested in foresight and cooperative during the whole process because they learned the use of foresight tools through collective solution of practical tasks which were important for them.

Out of Challenge, Opportunity: Central America's Electric Sector & Key Issues and Recommendations for Enhanced Regional Electric Integration

Taken together, the six nations of Central America count a population of roughly 40 million people and an energy market equal in size to that of Colombia, sufficient to benefit from economies of scale. The region has traditionally been a net importer of hydrocarbons, and hydroelectricity has dominated electric generation. But more recently, thermoelectric generation (diesel and fuel oil) has greatly increased as a percentage of the regional generation market. Progress has been made across the region’s electric sector, beginning with reforms in the 1990s and the 1996 signing of a regional treaty aimed at the development of a regional energy integration project – the Central American Electrical Interconnection System, or SIEPAC. A fundamental SIEPAC goal is to set up a regional electric market and a regulatory system. Indeed, after many years of development, SIEPAC is poised to open a new chapter in Central America’s electric infrastructure and market. But this new era must contend with critical issues such as the need to consolidate the regional electric market, political issues surrounding the venture, and security concerns. Moreover, local conflicts, in different degrees, have become priorities for policymakers, and these are possible barriers to completing the project. The goals of the SIEPAC project and of deepening the broader electric integration process are possible if national and regional decision makers understand that cooperative decision making will produce better results than separate national decision making. Enhanced regional understanding and cooperative decision making, combined with an effort to reorient the terminology and dialogue vis-à-vis energy efficiency in Central America, form the core recommendations of this paper.

The practice and use of picuristes (lay injectionists) among Haitian immigrants in Miami -Dade County, Florida

This exploratory study examined use of picuristes among Haitian immigrants in Miami-Dade County, Florida. It describes how this health-seeking behavior is socially constructed among Haitian immigrants in terms of benefits. (b) risks, (c) sex, (d) gender, (e) acculturation proxies, and (f) transnational influences. It is conducted within the frameworks of Symbolic Interactionism, the Health Belief Model and the Explanatory Model of Illness. ^ Purposive sampling and a mixed-method design were used to obtain semistructured interviews of 10 picuristes and 25 users. The same methods were employed to select survey respondents so as to obtain a descriptive estimate of picuriste use and covariates of picuriste use within the sample. ATLAS.ti 5.0 and SPSS 14.0 were used to analyze the data. ^ The findings indicate an interconnection of elements from Vodou, traditional Haitian health beliefs and picuriste practice and use. ^ Rekonnèt, a relationship based on a history of trust with individuals related by blood or who share close personal and social ties was identified as a sufficient and necessary reason for picuriste practice and use. ^ Benefits reported are that the picuriste injections directly impact the blood, and that they represent affordable and convenient access to health care. Risks include rashes, abscesses and fevers. The reuse of injection equipment, routine injection of antibiotics and unknown substances and the improper discard of syringes and needles were reported, implying unrecognized risks of preventable infectious disease. No participant described a process that adheres to established international standards for safe injections. ^ There is no clear evidence that biological sex, gender, length of time in U.S. or language of interview influence picuriste practice or use. Transnational ties facilitate transport of substances from Haiti and the practice and use of picuristes locally. ^ Recommendation by a relative or trusted friend and believing that the benefits of picures outweigh risks were covariates of picuriste use. ^ This study highlights values and priorities of Haitian immigrants seeking healthcare, and cultural forces that shape their decisions about wellness and treatment. Future studies should test the application of Symbolic Interactionism to picuriste use in larger epidemiological studies that examine picuriste use in relation to health status.^

Development of distributed generation infrastructure for microgrid connectivity to operational power systems

Distributed Generation (DG) from alternate sources and smart grid technologies represent good solutions for the increase in energy demands. Employment of these DG assets requires solutions for the new technical challenges that are accompanied by the integration and interconnection into operational power systems. A DG infrastructure comprised of alternate energy sources in addition to conventional sources, is developed as a test bed. The test bed is operated by synchronizing, wind, photovoltaic, fuel cell, micro generator and energy storage assets, in addition to standard AC generators. Connectivity of these DG assets is tested for viability and for their operational characteristics. The control and communication layers for dynamic operations are developed to improve the connectivity of alternates to the power system. A real time application for the operation of alternate sources in microgrids is developed. Multi agent approach is utilized to improve stability and sequences of actions for black start are implemented. Experiments for control and stability issues related to dynamic operation under load conditions have been conducted and verified.

Metodologia para gerenciamento de projetos em tecnologia da informação baseada no guia PMBOK: um estudo de caso na Secretaria de Estado da Saúde Pública do Rio Grande do Norte

Nowadays the search for growth makes organizations seeking competitive advantages, project management shares this goal, through techniques that assist in the search for an improved management of the various fields of knowledge through a design methodology. The world is driven by projects and the search for ways to better manage activities such as time, cost and term towards the success of a particular project is something constant. A major contribution that IT can make to the health sector is the support for the management area. IT can integrate processes, optimize the interconnection between the various sectors, make hospitals have access to inside information of good quality, as well as support in the healthcare area, sharing pictures, uniting the various aspects of nursing and nursing service. The major challenge faced by the SESAP Information Technology sector at present is in project management in IT , which does not exist makes investments in the area are increasingly difficult due to this deficiency in management develop their own systems without cost additional to the State. This study seeks to build and strengthen the Project Management within the Department of Health through the implementation of a project office that will manage the final result of this work methodology based on PMBOK, and still show the functionality applied to development the state Hospital Management System that will later be installed on all Regional Health Units and proposing measures for the sustainability and development of the sector amid the difficulties of the current public service. Such action will result in a savings of more than R$ 107,000.00 (one hundred seven thousand) regarding spending private software currently used by the assignment of invested by the State of Rio Grande do Norte user licenses, representing more than 5 % of the total budget of the State Department of Public Health of the State

Mecanismo de tolerância a falhas através de escalonamento para uma arquitetura reconfigurável de grão grosso

The continuous evolution of integrated circuit technology has allowed integrating thousands of transistors on a single chip. This is due to the miniaturization process, which reduces the diameter of wires and transistors. One drawback of this process is that the circuit becomes more fragile and susceptible to break, making the circuit more susceptible to permanent faults during the manufacturing process as well as during their lifetime. Coarse Grained Reconfigurable Architectures (CGRAs) have been used as an alternative to traditional architectures in an attempt to tolerate such faults due to its intrinsic hardware redundancy and high performance. This work proposes a fault tolerance mechanism in a CGRA in order to increase the architecture fault tolerance even considering a high fault rate. The proposed mechanism was added to the scheduler, which is the mechanism responsible for mapping instructions onto the architecture. The instruction mapping occurs at runtime, translating binary code without the need for recompilation. Furthermore, to allow faster implementation, instruction mapping is performed using a greedy module scheduling algorithm, which consists of a software pipeline technique for loop acceleration. The results show that, even with the proposed mechanism, the time for mapping instructions is still in order of microseconds. This result allows that instruction mapping process remains at runtime. In addition, a study was also carried out mapping scheduler rate. The results demonstrate that even at fault rates over 50% in functional units and interconnection components, the scheduler was able to map instructions onto the architecture in most of the tested applications.

Contribuições para estratégia de controle aplicada à geração fotovoltaica interconectada à rede elétrica

Generation systems, using renewable sources, are becoming increasingly popular due to the need for increased use of electricity. Currently, renewables sources have a role to cooperate with conventional generation, due to the system limitation in delivering the required power, the need for reduction of unwanted effects from sources that use fossil fuels (pollution) and the difficulty of building new transmission and/or distribution lines. This cooperation takes place through distributed generation. Therefore, this work proposes a control strategy for the interconnection of a PV (Photovoltaic) system generation distributed with a three-phase power grid through a connection filter the type LCL. The compensation of power quality at point of common coupling (PCC) is performed ensuring that the mains supply or consume only active power and that his currents have low distorcion. Unlike traditional techniques which require schemes for harmonic detection, the technique performs the harmonic compensation without the use of this schemes, controlling the output currents of the system in an indirect way. So that there is effective control of the DC (Direct Current) bus voltage is used the robust controller mode dual DSMPI (Dual-Sliding Mode-Proportional Integral), that behaves as a sliding mode controller SM-PI (Sliding Mode-Proportional Integral) during the transition and like a conventional PI (Proportional Integral) in the steady-state. For control of current is used to repetitive control strategy, which are used double sequence controllers (DSC) tuned to the fundamental component, the fifth and seventh harmonic. The output phase current are aligned with the phase angle of the utility voltage vector obtained from the use of a SRF-PLL (Synchronous Reference Frame Phase-Locked-Loop). In order to obtain the maximum power from the PV array is used a MPPT (Maximum Power Point Tracking) algorithm without the need for adding sensors. Experimental results are presented to demonstrate the effectiveness of the proposed control system.

Evolução dos sistemas de falhas de borda do Rifte Potiguar com base em curvas de crescimento de falhas

The discussion about rift evolution in the Brazilian Equatorial margin during the South America-Africa breakup in the Jurassic/Cretaceous has been focused in many researches. But rift evolution based on development and growth of faults has not been well explored. In this sense, we investigated the Cretaceous Potiguar Basin in the Equatorial margin of Brazil to understand the geometry of major faults and the influence of crustal heterogeneity and preexisting structural fabric in the evolution of the basin internal architecture. Previous studies pointed out that the rift is an asymmetrical half-graben elongated along the NE-SW direction. We used 2D seismic, well logs and 3D gravity modeling to analyze four major border fault segments and determine their maximum displacement (Dmax) and length (L) ratio in the Potiguar Rift. We constrained the 3D gravity modeling with well data and the interpretation of seismic sections. The difference of the fault displacement measured in the gravity model is in the order of 10% compared to seismic and well data. The fault-growth curves allowed us to divide the faulted rift border into four main fault segments, which provide roughly similar Dmax/L ratios. Fault-growth curves suggest that a regional uniform tectonic mechanism influenced growth of the rift fault segments. The variation of the displacements along the fault segments indicates that the fault segments were formed independently during rift initiation and were linked by hard and soft linkages. The latter formed relay ramps. In the interconnection zones the Dmax/L ratios are highest due to interference of fault segment motions. We divided the evolution of the Potiguar Rift into five stages based on these ratios and correlated them with the major tectonic stages of the breakup between South America and Africa in Early Cretaceous.

Evolução dos sistemas de falhas de borda do Rifte Potiguar com base em curvas de crescimento de falhas

The discussion about rift evolution in the Brazilian Equatorial margin during the South America-Africa breakup in the Jurassic/Cretaceous has been focused in many researches. But rift evolution based on development and growth of faults has not been well explored. In this sense, we investigated the Cretaceous Potiguar Basin in the Equatorial margin of Brazil to understand the geometry of major faults and the influence of crustal heterogeneity and preexisting structural fabric in the evolution of the basin internal architecture. Previous studies pointed out that the rift is an asymmetrical half-graben elongated along the NE-SW direction. We used 2D seismic, well logs and 3D gravity modeling to analyze four major border fault segments and determine their maximum displacement (Dmax) and length (L) ratio in the Potiguar Rift. We constrained the 3D gravity modeling with well data and the interpretation of seismic sections. The difference of the fault displacement measured in the gravity model is in the order of 10% compared to seismic and well data. The fault-growth curves allowed us to divide the faulted rift border into four main fault segments, which provide roughly similar Dmax/L ratios. Fault-growth curves suggest that a regional uniform tectonic mechanism influenced growth of the rift fault segments. The variation of the displacements along the fault segments indicates that the fault segments were formed independently during rift initiation and were linked by hard and soft linkages. The latter formed relay ramps. In the interconnection zones the Dmax/L ratios are highest due to interference of fault segment motions. We divided the evolution of the Potiguar Rift into five stages based on these ratios and correlated them with the major tectonic stages of the breakup between South America and Africa in Early Cretaceous.

Optical fiber sensors embedded in flexible polymer foils

In traditional electrical sensing applications, multiplexing and interconnecting the different sensing elements is a major challenge. Recently, many optical alternatives have been investigated including optical fiber sensors of which the sensing elements consist of fiber Bragg gratings. Different sensing points can be integrated in one optical fiber solving the interconnection problem and avoiding any electromagnetical interference (EMI). Many new sensing applications also require flexible or stretchable sensing foils which can be attached to or wrapped around irregularly shaped objects such as robot fingers and car bumpers or which can even be applied in biomedical applications where a sensor is fixed on a human body. The use of these optical sensors however always implies the use of a light-source, detectors and electronic circuitry to be coupled and integrated with these sensors. The coupling of these fibers with these light sources and detectors is a critical packaging problem and as it is well-known the costs for packaging, especially with optoelectronic components and fiber alignment issues are huge. The end goal of this embedded sensor is to create a flexible optical sensor integrated with (opto)electronic modules and control circuitry. To obtain this flexibility, one can embed the optical sensors and the driving optoelectronics in a stretchable polymer host material. In this article different embedding techniques for optical fiber sensors are described and characterized. Initial tests based on standard manufacturing processes such as molding and laser structuring are reported as well as a more advanced embedding technique based on soft lithography processing.

Structural and Biochemical Dissection of the Trehalose Biosynthetic Complex in Pathogenic Fungi

Trehalose is a non-reducing disaccharide essential for pathogenic fungal survival and virulence. The biosynthesis of trehalose requires the trehalose-6-phosphate synthase, Tps1, and trehalose-6-phosphate phosphatase, Tps2. More importantly, the trehalose biosynthetic pathway is absent in mammals, conferring this pathway as an ideal target for antifungal drug design. However, lack of germane biochemical and structural information hinders antifungal drug design against these targets.

In this dissertation, macromolecular X-ray crystallography and biochemical assays were employed to understand the structures and functions of proteins involved in the trehalose biosynthetic pathway. I report here the first eukaryotic Tps1 structures from Candida albicans (C. albicans) and Aspergillus fumigatus (A. fumigatus) with substrates or substrate analogs. These structures reveal the key residues involved in substrate binding and catalysis. Subsequent enzymatic assays and cellular assays highlight the significance of these key Tps1 residues in enzyme function and fungal stress response. The Tps1 structure captured in its transition-state with a non-hydrolysable inhibitor demonstrates that Tps1 adopts an “internal return like” mechanism for catalysis. Furthermore, disruption of the trehalose biosynthetic complex formation through abolishing Tps1 dimerization reveals that complex formation has regulatory function in addition to trehalose production, providing additional targets for antifungal drug intervention.

I also present here the structure of the Tps2 N-terminal domain (Tps2NTD) from C. albicans, which may be involved in the proper formation of the trehalose biosynthetic complex. Deletion of the Tps2NTD results in a temperature sensitive phenotype. Further, I describe in this dissertation the structures of the Tps2 phosphatase domain (Tps2PD) from C. albicans, A. fumigatus and Cryptococcus neoformans (C. neoformans) in multiple conformational states. The structures of the C. albicans Tps2PD -BeF3-trehalose complex and C. neoformans Tps2PD(D24N)-T6P complex reveal extensive interactions between both glucose moieties of the trehalose involving all eight hydroxyl groups and multiple residues of both the cap and core domains of Tps2PD. These structures also reveal that steric hindrance is a key underlying factor for the exquisite substrate specificity of Tps2PD. In addition, the structures of Tps2PD in the open conformation provide direct visualization of the conformational changes of this domain that are effected by substrate binding and product release.

Last, I present the structure of the C. albicans trehalose synthase regulatory protein (Tps3) pseudo-phosphatase domain (Tps3PPD) structure. Tps3PPD adopts a haloacid dehydrogenase superfamily (HADSF) phosphatase fold with a core Rossmann-fold domain and a α/β fold cap domain. Despite lack of phosphatase activity, the cleft between the Tps3PPD core domain and cap domain presents a binding pocket for a yet uncharacterized ligand. Identification of this ligand could reveal the cellular function of Tps3 and any interconnection of the trehalose biosynthetic pathway with other cellular metabolic pathways.

Combined, these structures together with significant biochemical analyses advance our understanding of the proteins responsible for trehalose biosynthesis. These structures are ready to be exploited to rationally design or optimize inhibitors of the trehalose biosynthetic pathway enzymes. Hence, the work described in this thesis has laid the groundwork for the design of Tps1 and Tps2 specific inhibitors, which ultimately could lead to novel therapeutics to treat fungal infections.

System packaging & integration for a swallowable capsule using a direct access sensor

Technological developments in biomedical microsystems are opening up new opportunities to improve healthcare procedures. Swallowable diagnostic capsules are an example of this. In this paper, a diagnostic capsule technology is described based on direct-access sensing of the Gastro Intestinal (GI) fluids throughout the GI tract. The objective of this paper is two-fold: i) develop a packaging method for a direct access sensor, ii) develop an encapsulation method to protect the system electronics. The integrity of the interconnection after sensor packaging and encapsulation is correlated to its reliability and thus of importance. The zero level packaging of the sensor was achieved by using a so called Flip Chip Over Hole (FCOH) method. This allowed the fluidic sensing media to interface with the sensor, while the rest of the chip including the electrical connections can be insulated effectively. Initial tests using Anisotropic Conductive Adhesive (ACA) interconnect for the FCOH demonstrated good electrical connections and functionality of the sensor chip. Also a preliminary encapsulation trial of the flip chipped sensor on a flexible test substrate has been carried out and showed that silicone encapsulation of the system is a viable option.

Development and reliability of a direct access sensor using flip chip on flex technology with anisotropic conductive adhesive

Technological developments in biomedical microsystems are opening up new opportunities to improve healthcare procedures. Swallowable diagnostic sensing capsules are an example of these. In none of the diagnostic sensing capsules, is the sensor’s first level packaging achieved via Flip Chip Over Hole (FCOH) method using Anisotropic Conductive Adhesive (ACA). In a capsule application with direct access sensor (DAS), ACA not only provides the electrical interconnection but simultaneously seals the interconnect area and the underlying electronics. The development showed that the ACA FCOH was a viable option for the DAS interconnection. Adequate adhesive formed a strong joint that withstood a shear stress of 120N/mm2 and a compressive stress of 6N required to secure the final sensor assembly in place before encapsulation. Electrical characterization of the ACA joint in a fluid environment showed that the ACA was saturated with moisture and that the ions in the solution actively contributed to the leakage current, characterized by the varying rate of change of conductance. Long term hygrothermal aging of the ACA joint showed that a thermal strain of 0.004 and a hygroscopic strain of 0.0052 were present and resulted in a fatigue like process. In-vitro tests showed that high temperature and acidity had a deleterious effect of the ACA and its joint. It also showed that the ACA contact joints positioned at around or over 1mm would survive the gastrointestinal (GI) fluids and would be able to provide a reliable contact during the entire 72hr of the GI transit time. A final capsule demonstrator was achieved by successfully integrating the DAS, the battery and the final foldable circuitry into a glycerine capsule. Final capsule soak tests suggested that the silicone encapsulated system could survive the 72hr gut transition.