Domestication of an endangered fish species Nandus nandus (Ham.). Pt. 1. Laboratory rearing of young fish up to sexual maturity

An experiment was conducted for rearing of Meni, Nandus nandus in laboratory condition for seven months with the objective to select appropriate feed for the species and to develop a rearing technique of the species up to the stage of sexual maturation. Different trials were conducted using artificial feed (35.5% protein), dead fresh kachki (Carica soborna), dead fresh prawn (Macrobrachium lamarrei) and live prawn (Macrobrachium lamarrei). The provision of bottom sediment did not significantly influence the growth of fish. Between dead fresh kachki and dead fresh prawn, the fish preferred dead fresh prawn. The fish was found to be reluctant to take dead fresh kachki and prawn as food unless they became very hungry. The fish was found actively feeding on live prawn. The FCR of the prawn as food for N. nandus was found to be 2.5. From the study, it was observed that in laboratory rearing N. nandus preferred live prawn as food than artificial feed, dead fresh kachki and dead fresh prawn. The fish fed on live prawn became sexually matured (eggs or white milt extruded by gentle pressure on the abdomen of the fish) in the laboratory at the end of the experiment.

Yielding of engineering polymers at strain rates of up to 500 s-1

A method is described for measuring the mechanical properties of polymers in compression at strain rates in the range approximately 300-500 s-1. A gravity-driven pendulum is used to load a specimen on the end of an instrumented Hopkinson output bar and the results are processed by a microcomputer. Stress-strain curves up to high strains are presented for polycarbonate, polyethersulphone and high density polyethylene over a range of temperatures. The value of yield stress, for all three polymers, was found to vary linearly with log (strain rate) at strain rates up to 500 s-1. © 1985.

New evidences on the distribution of predatory pelagic sharks in the tuna grounds of the Indian Ocean

Since the commencement of the exploitation of oceanic tuna resources of the Indian Ocean seventeen years ago, the hooked rates for the tuna species have declined in many areas of the Ocean but there are no evidences of such a trend in the case of the sharks. As a result, the percentage composition of sharks in the longline catches and the percentage of the tuna catch damaged by sharks show an increase. Hence there is an urgent need for innovation of the existing longline gear in order to increase the fishing efficiency for hooking the tuna species with a corresponding reduction in its efficiency for hooking sharks. At the beginning of this fishery, hooked sharks were discarded at sea, at a later stage the liver and fins were taken and the carcass discarded and presently the sharks are also brought along with the tuna catch. Though the shark meat has a very low market value it is brought in order to cover up for the declining tuna catches. Thus it has become very necessary to increase the demand for shark meat by developing products or by-products utilizing shark meat and ensuring the successful continuity of the tuna longline fishery. The pattern of distribution of shark species in the time grounds of the Pacific, Indian and Atlantic Oceans and also the predation of hooked tunas by sharks were discussed earlier (Sivasubranianiam 1963, 1964 and 1966). Some contribution to these studies is made in this paper based on new data become available.

Analysis of the piston ring/liner oil film development during warm-up for an SI-engine

A one-dimensional ring-pack lubrication model developed at MIT is applied to simulate the oil film behavior during the warm-up period of a Kohler spark ignition engine [1]. This is done by making assumptions for the evolution of the oil temperatures during warm-up and that the oil control ring during downstrokes is fully flooded. The ring-pack lubrication model includes features such as three different lubrication regimes, i.e. pure hydrodynamic lubrication, boundary lubrication and pure asperity contact, non-steady wetting of both inlet and outlet of the piston ring, capability to use all ring face profiles that can be approximated by piece-wise polynomials and, finally, the ability to model the rheology of multi-grade oils. Not surprisingly, the simulations show that by far the most important parameter is the temperature dependence of the oil viscosity. This dependence is subsequently examined further by choosing different oils. The baseline oil is SAE 10W30 and results are compared to those using the SAE 30 and the SAE 10W50 oils.

Starting-up roadmapping fast

Technology roadmapping is a powerful technique for supporting technology management and planning in the firm. The roadmap enables the evolution of markets, products and technologies to be explored, together with the linkages between the various perspectives. A process called T-Plan, which has been developed to support the rapid initiation of roadmapping and thus address these challenges is described.

Statistical energy analysis of a built-up structure excited through its stiffening members

A new method of analysing high frequency vibrations in stiffened structures requires the calculation of a "power absorbing impedance matrix" for each plate in the system. The present paper is concerned with formulating this matrix by using point collocation in conjunction with basis functions representing incoming cylindrical waves. Key numerical issues are highlighted by considering the special case of a membrane, rather than a plate, and conclusions are made regarding the utility of the method.