Evaluation of Bias in the Hamburg Wheel Tracking Device, RB00-010, 2013

As the list of states adopting the HWTD continues to grow, there is a need to evaluate how results are utilized. AASHTO T 324 does not standardize the analysis and reporting of test results. Furthermore, processing and reporting of the results among manufacturers is not uniform. This is partly due to the variation among agency reporting requirements. Some include only the midpoint rut depth, while others include the average across the entire length of the wheel track. To eliminate bias in reporting, statistical analysis was performed on over 150 test runs on gyratory specimens. Measurement location was found to be a source of significant variation in the HWTD. This is likely due to the nonuniform wheel speed across the specimen, geometry of the specimen, and air void profile. Eliminating this source of bias when reporting results is feasible though is dependent upon the average rut depth at the final pass. When reporting rut depth at the final pass, it is suggested for poor performing samples to average measurement locations near the interface of the adjoining gyratory specimens. This is necessary due to the wheel lipping on the mold. For all other samples it is reasonable to only eliminate the 3 locations furthest from the gear house. For multi‐wheel units, wheel side was also found to be significant for poor and good performing samples. After eliminating the suggested measurements from the analysis, the wheel was no longer a significant source of variation.

Whole-body vibration training: metabolic cost of synchronous, side-alternating or no vibrations.

Whole-body vibration training improves strength and can increase maximal oxygen consumption ([·V]O(2max)). No study has compared the metabolic demand of synchronous and side-alternating whole-body vibration. We measured [·V]O₂ and heart rate during a typical synchronous or side-alternating whole-body vibration session in 10 young female sedentary participants. The 20-min session consisted of three sets of six 45-s exercises, with 15 s recovery between exercises. Three conditions were randomly tested on separate days: synchronous at 35 Hz and 4 mm amplitude, side-alternating at 26 Hz and 7.5 mm amplitude (peak acceleration matched at 20 g in both vibration conditions), and no vibrations. Mean [·V]O₂ (expressed as %[·V]O(2max)) did not differ between conditions: 29.7 ± 4.2%, 32.4 ± 6.5%, and 28.7 ± 6.7% for synchronous, side-alternating, and no vibrations respectively (P = 0.103). Mean heart rate (% maximal heart rate) was 65.6 ± 7.3%, 69.8 ± 7.9%, and 64.7 ± 5.6% for synchronous, side-alternating, and no vibrations respectively, with the side-alternating vibrations being significantly higher (P = 0.019). When analysing changes over exercise sessions, mean [·V]O₂ was higher for side-alternating (P < 0.001) than for synchronous and no vibrations. In conclusion, side-alternating whole-body vibration elicits higher heart rate responses than synchronous or no vibrations, and could elevate [·V]O₂, provided the session lasts more than 20 min.

Combined use of the GGSFT data base and on Board Marine Collected Data to Model the Moho Beneath the Powell Basin, Antarctica

The Powell Basin is a small oceanic basin located at the NE end of the Antarctic Peninsula developed during the Early Miocene and mostly surrounded by the continental crusts of the South Orkney Microcontinent, South Scotia Ridge and Antarctic Peninsula margins. Gravity data from the SCAN 97 cruise obtained with the R/V Hespérides and data from the Global Gravity Grid and Sea Floor Topography (GGSFT) database (Sandwell and Smith, 1997) are used to determine the 3D geometry of the crustal-mantle interface (CMI) by numerical inversion methods. Water layer contribution and sedimentary effects were eliminated from the Free Air anomaly to obtain the total anomaly. Sedimentary effects were obtained from the analysis of existing and new SCAN 97 multichannel seismic profiles (MCS). The regional anomaly was obtained after spectral and filtering processes. The smooth 3D geometry of the crustal mantle interface obtained after inversion of the regional anomaly shows an increase in the thickness of the crust towards the continental margins and a NW-SE oriented axis of symmetry coinciding with the position of an older oceanic spreading axis. This interface shows a moderate uplift towards the western part and depicts two main uplifts to the northern and eastern sectors.

Determination of Asphalt Content and Characteristics of Bituminous Paving Mixtures, MLR-88-11, 1988

Due to the hazardous nature of chemical asphalt extraction agents, nuclear gauges have become an increasingly popular method of determining the asphalt content of a bituminous mix. This report details the results of comparisons made between intended, tank stick, extracted, and nuclear asphalt content determinations. A total of 315 sets of comparisons were made on samples that represented 110 individual mix designs and 99 paving projects. All samples were taken from 1987 construction projects. In addition to the comparisons made, seventeen asphalt cement samples were recovered for determination of penetration and viscosity. Results were compared to similar tests performed on the asphalt assurance samples in an attempt to determine the amount of asphalt hardening that can be expected due to the hot mix process. Conclusions of the report are: 1. Compared to the reflux extraction procedure, nuclear asphalt content gauges determine asphalt content of bituminous mixes with much greater accuracy and comparable precision. 2. As a means for determining asphalt content, the nuclear procedure should be used as an alternate to chemical extractions whenever possible. 3. Based on penetration and viscosity results, softer grade asphalts undergo a greater degree 'of hardening due to hot mix processing than do harder grades, and asphalt viscosity changes caused by the mixing process are subject to much more variability than are changes in penetration. 4. Based on changes in penetration and viscosity, the Thin Film Oven Test provides a reasonable means of estimating how much asphalt hardening can be anticipated due to exposure to the hot mix processing environment.

A Generalized Model Study of Scour Around Bridge Piers and Abutments, HR-24, 1953

Four classes of variables are apparent in the problem of scour around bridge piers and abutments--geometry of piers and abutments, stream-flow characteristics, sediment characteristics, and geometry of site. The laboratory investigation, from its inception, has been divided into four phases based on these classes. In each phase the variables in three of the classes are held constant and those in the pertinent class are varied. To date, the first three phases have been studied. Typical scour bole patterns related to the geometry of the pier or abutment have been found. For equilibrium conditions of scour with uniform sand, the velocity of flow and the sand size do not appear to have any measurable effects on the depth of scour. This result is especially encouraging in the search for correlation between model and prototype since it would indicate that, primarily, only the depth of flow might be involved in the scale effect. The technique of model testing has been simplified, therefore, because rate of sediment transportation does not need to be scaled. Prior to the establishment of equilibrium conditions, however, depths of scour in excess of those for equilibrium conditions have been found. A concept of active scour as an imbalance between sediment transport capacity and rate of sediment supply has been used to explain the laboratory observations.

Crustal structure and reflectivity of the Swiss Alps from 3-Dimensional seismic modeling. 2. Penninic Nappes

Surface geological mapping, laboratory measurements of rock properties, and seismic reflection data are integrated through three-dimensional seismic modeling to determine the likely cause of upper crustal reflections and to elucidate the deep structure of the Penninic Alps in eastern Switzerland. Results indicate that the principal upper crustal reflections recorded on the south end of Swiss seismic line NFP20-EAST can be explained by the subsurface geometry of stacked basement nappes. In addition, modeling results provide improvements to structural maps based solely on surface trends and suggest the presence of previously unrecognized rock units in the subsurface. Construction of the initial model is based upon extrapolation of plunging surface. structures; velocities and densities are established by laboratory measurements of corresponding rock units. Iterative modification produces a best fit model that refines the definition of the subsurface geometry of major structures. We conclude that most reflections from the upper 20 km can be ascribed to the presence of sedimentary cover rocks (especially carbonates) and ophiolites juxtaposed against crystalline basement nappes. Thus, in this area, reflections appear to be principally due to first-order lithologic contrasts. This study also demonstrates not only the importance of three-dimensional effects (sideswipe) in interpreting seismic data, but also that these effects can be considered quantitatively through three-dimensional modeling.

Direct numerical simulations of interface dynamics to link capillary pressure and total surface energy

The flow of two immiscible fluids through a porous medium depends on the complex interplay between gravity, capillarity, and viscous forces. The interaction between these forces and the geometry of the medium gives rise to a variety of complex flow regimes that are difficult to describe using continuum models. Although a number of pore-scale models have been employed, a careful investigation of the macroscopic effects of pore-scale processes requires methods based on conservation principles in order to reduce the number of modeling assumptions. In this work we perform direct numerical simulations of drainage by solving Navier-Stokes equations in the pore space and employing the Volume Of Fluid (VOF) method to track the evolution of the fluid-fluid interface. After demonstrating that the method is able to deal with large viscosity contrasts and model the transition from stable flow to viscous fingering, we focus on the macroscopic capillary pressure and we compare different definitions of this quantity under quasi-static and dynamic conditions. We show that the difference between the intrinsic phase-average pressures, which is commonly used as definition of Darcy-scale capillary pressure, is subject to several limitations and it is not accurate in presence of viscous effects or trapping. In contrast, a definition based on the variation of the total surface energy provides an accurate estimate of the macroscopic capillary pressure. This definition, which links the capillary pressure to its physical origin, allows a better separation of viscous effects and does not depend on the presence of trapped fluid clusters.

Sedimentation of pairs of hydrodynamically interacting semiflexible filaments

We describe the effect of hydrodynamic interactions in the sedimentation of a pair of inextensible semiflexible filaments under a uniform constant force at low Reynolds numbers. We have analyzed the different regimes and the morphology of such polymers in simple geometries, which allow us to highlight the peculiarities of the interplay between elastic and hydrodynamic stresses. Cooperative and symmetry breaking effects associated to the geometry of the fibers gives rise to characteristic motion which give them distinct properties from rigid and elastic filaments.

Methionine-321 in the C-terminal alpha-helix of catabolic ornithine carbamoyltransferase from Pseudomonas aeruginosa is important for positive homotropic cooperativity.

Pseudomonas aeruginosa has a pair of distinct ornithine carbamoyltransferases. The anabolic ornithine carbamoyltransferase encoded by the argF gene catalyzes the formation of citrulline from ornithine and carbamoylphosphate. The catabolic ornithine carbamoyltransferase encoded by the arcB gene promotes the reverse reaction in vivo; although this enzyme can be assayed in vitro for citrulline synthesis, its unidirectionality in vivo is determined by its high concentration at half maximum velocity for carbamoylphosphate ([S]0.5) and high cooperativity toward this substrate. We have isolated mutant forms of catabolic ornithine carbamoyltransferase catalyzing the anabolic reaction in vivo. The corresponding arcB mutant alleles on a multicopy plasmid specifically suppressed an argF mutation of P. aeruginosa. Two new mutant enzymes were obtained. When methionine 321 was replaced by isoleucine, the mutant enzyme showed loss of homotropic cooperativity at physiological carbamoylphosphate concentrations. Substitution of glutamate 105 by lysine resulted in a partial loss of the sigmoidal response to increasing carbamoylphosphate concentrations. However, both mutant enzymes were still sensitive to the allosteric activator AMP and to the inhibitor spermidine. These results indicate that at least two residues of catabolic ornithine carbamoyltransferase are critically involved in positive carbamoylphosphate cooperativity: glutamate 105 (previously known to be important) and methionine 321. Mutational changes in either amino acid will affect the geometry of helix H2, which contains several residues required for carbamoylphosphate binding.

The Caribbean-North America-Cocos Triple Junction and the dynamics of the Polochic-Motagua fault systems: Pull-up and zipper models

The Polochic-Motagua fault systems (PMFS) are part of the sinistral transform boundary between the North American and Caribbean plates. To the west, these systems interact with the subduction zone of the Cocos plate, forming a subduction-subduction-transform triple junction. The North American plate moves westward relative to the Caribbean plate. This movement does not affect the geometry of the subducted Cocos plate, which implies that deformation is accommodated entirely in the two overriding plates. Structural data, fault kinematic analysis, and geomorphic observations provide new elements that help to understand the late Cenozoic evolution of this triple junction. In the Miocene, extension and shortening occurred south and north of the Motagua fault, respectively. This strain regime migrated northward to the Polochic fault after the late Miocene. This shift is interpreted as a ``pull-up'' of North American blocks into the Caribbean realm. To the west, the PMFS interact with a trench-parallel fault zone that links the Tonala fault to the Jalpatagua fault. These faults bound a fore-arc sliver that is shared by the two overriding plates. We propose that the dextral Jalpatagua fault merges with the sinistral PMFS, leaving behind a suturing structure, the Tonala fault. This tectonic ``zipper'' allows the migration of the triple junction. As a result, the fore-arc sliver comes into contact with the North American plate and helps to maintain a linear subduction zone along the trailing edge of the Caribbean plate. All these processes currently make the triple junction increasingly diffuse as it propagates eastward and inland within both overriding plates.

Structure and kinematics of the Siviez-Mischabel nappe in the Mattertal (western Alps of Switzerland) = Structure et cinématique de la nappe de Siviez-Mischabel le long de la vallée de Zermatt (Alpes de Suisse occidentale)

Résumé Cette étude porte sur le flanc inverse de la nappe de Siviez-Mischabel et sur les unités tectoniques sous jacentes (zone de Stalden supérieur et zone Houillère) dans la vallée menant à Zermatt. L'étude structurale du granite permien de Randa (orthogneiss oeillé) permet de mieux comprendre les effets de la déformation alpine sur les roches de socle. La cartographie détaillée de l'orthogneiss et de son encaissant, ainsi que l'étude lithostratigraphique des terrains sédimentaires associés permettent de proposer un schéma structural et cinématique du flanc inverse de la nappe de Siviez-Mischabel et de mieux comprendre ses relations avec les unités tectoniques sous-jacentes. L'analyse structurale de l'orthogneiss de Randa et de son encaissant révèle la superposition de plusieurs phases de déformation ductile. Cet orthogneiss formé sous des conditions métamorphiques du faciès schiste vert possède une forte schistosité alpine avec au moins deux linéations d'extension. La première, L1, orientée NW-SE est associée à la mise en place de la nappe. La seconde, L2, orientée SW-NE, se corrèle au cisaillement ductile du Simplon. La quantification de la déformation au moyen de la méthode de Fry sur les faciès porphyriques donne des ellipses à rapports axiaux compris entre 1.9 et 5.3, en accord avec les valeurs obtenues par d'autres marqueurs {tourmalines étirées, fibres). Les valeurs mesurées parallèlement à L1 ou L2 sont très semblables. La méthode de Fry a nécessité une étude théorique préalable afin de vérifier son applicabilité aux orthogneiss oeillés. La méthode requiert une distribution spatiale homogène et isotrope des marqueurs utilisés. Les tests statistiques effectués ont révélé que les phénocristaux de feldspath alcalin satisfont à cette condition et qu'ils peuvent être utilisés comme marqueur de la déformation au moyen de la méthode de Fry. Les valeurs obtenues révèlent l'importance du cisaillement ductile du Simplon sur la géométrie de la nappe dans la région d'étude. Le levé cartographique a permis d'améliorer la lithostratigraphie de la base de la nappe de Siviez-Mischabel. Trois formations en position renversée peuvent être observées sous les gneiss formant le coeur de la nappe. Ces trois formations forment le coeur du synclinal de St-Niklaus qui connecte la nappe de Siviez-Mischabel à la zone de Stalden supérieur. La datation par U-Pb de zircons détritiques et magmatiques par LA-ICP-MS permet de contraindre l'âge des formations observées (probablement Carbonifère à Trias précoce). Ces données ont des répercussions importantes sur la structure de la nappe dans la région, prouvant l'existence de plusieurs plis avec des séries normales et renversées bien préservées. La définition et la datation de ces formations, ainsi que leur identification dans la-Zone- Houillère avoisinante permettent de mieux comprendre la géométrie initiale et les relations tectoniques des nappes du Pennique moyen dans la vallée de Zermatt. Summary This study investigates the overturned limb of the Siviez-Mischabel nappe and underlying tectonic units (Upper Stalden zone and Houillère zone) in the Mattertal area. Detailed structural analysis in the Permian Randa granite (augen orthogneiss) allows a better understanding of the Alpine deformation effects on basement rocks. Detailed mapping of this orthogneiss and surrounding rocks, and the study of the lithostratigraphy in the related sedimentary horizons allow the proposition of a structural and kinematic model for the overturned limb of the Siviez-Mischabel and to better understand the relations with the underlying tectonic units. The structural analysis of the Randa orthogneiss and surrounding rocks revealed the superposition of several phases of ductile deformation. This orthogneiss formed under greenschist facies metamorphic conditions displays a strong Alpine foliation with at least two stretching lineations. The first lineation, L1, is oriented NW-SE and is related to the nappe emplacement northward. The second one, L2, is related to the Simplon ductile shear zone. Strain estimation using the Fry method has been performed on porphyritic facies of the Randa orthogneiss. The obtained ellipses have axial ratios varying between 1.9 and 5.3, in agreement with strain estimation obtained from other markers (stretched turmalines, fringes). The strain values are very similar if measured parallel to L1 or to L2. A theoretical approach was necessary to verify the relevant application of the Fry method to augen orthogneiss. This method requires that the distribution of the used markers has to be homogeneous and isotropic. Statistical tests have been done and revealed that K-feldspar phenocrysts satisfy these conditions and can be used as strain markers with the Fry method. The obtained strain measurements revealed the importance of the Simplon ductile shear zone on the geometry of the nappe in the studied area. Mapping has improved the lithostratigraphy at the base of the Siviez-Mischabel nappe. Three overturned formations can be observed below the gneisses forming the core of the nappe. These three formations form the St-Niklaus syncline, which connects the Siviez-Mischabel nappe to the underlying Upper Stalden zone. U-Pb dating of detrital and magmatic zircons by LA-ICPMS allowed the age of the observed formations to be constrained (presumably Carboniferous to Early Triassic). This data has critical implications for nappe structure in the region, composed of few recumbent folds with well preserved normal and overturned limbs. The definition and dating of these formations, as well as their identification in the adjacent "Houillère Zone" improve the understanding of the geometry and tectonic relations of the Middle Penninic nappes in the Mattertal.

Construction mechanisms and thermal evolution of upper crustal intrusions : the Saint-Jean-du-Doigt bimodal intrusion (Brittany, France)

Understanding the emplacement and growth of intrusive bodies in terms of mechanism, duration, ther¬mal evolution and rates are fundamental aspects of crustal evolution. Recent studies show that many plutons grow in several Ma by in situ accretion of discrete magma pulses, which constitute small-scale magmatic reservoirs. The residence time of magmas, and hence their capacities to interact and differentiate, are con¬trolled by the local thermal environment. The latter is highly dependant on 1) the emplacement depth, 2) the magmas and country rock composition, 3) the country rock thermal conductivity, 4) the rate of magma injection and 5) the geometry of the intrusion. In shallow level plutons, where magmas solidify quickly, evi¬dence for magma mixing and/or differentiation processes is considered by many authors to be inherited from deeper levels. This work shows however that in-situ differentiation and magma interactions occurred within basaltic and felsic sills at shallow depth (0.3 GPa) in the St-Jean-du-Doigt (SJDD) bimodal intrusion, France. This intrusion emplaced ca. 347 Ma ago (IDTIMS U/Pb on zircon) in the Precambrian crust of the Armori- can massif and preserves remarkable sill-like emplacement processes of bimodal mafic-felsic magmas. Field evidence coupled to high precision zircon U-Pb dating document progressive thermal maturation within the incrementally built ioppolith. Early m-thick mafic sills (eastern part) form the roof of the intrusion and are homogeneous and fine-grained with planar contacts with neighboring felsic sills; within a minimal 0.8 Ma time span, the system gets warmer (western part). Sills are emplaced by under-accretion under the old east¬ern part, interact and mingle. A striking feature of this younger, warmer part is in-situ differentiation of the mafic sills in the top 40 cm of the layer, which suggests liquids survival in the shallow crust. Rheological and thermal models were performed in order to determine the parameters required to allow this observed in- situ differentiation-accumulation processes. Strong constraints such as total emplacement durations (ca. 0.8 Ma, TIMS date) and pluton thickness (1.5 Km, gravity model) allow a quantitative estimation of the various parameters required (injection rates, incubation time,...). The results show that in-situ differentiation may be achieved in less than 10 years at such shallow depth, provided that: (1) The differentiating sills are injected beneath consolidated, yet still warm basalt sills, which act as low conductive insulating screens (eastern part formation in the SJDD intrusion). The latter are emplaced in a very short time (800 years) at high injection rate (0.5 m/y) in order to create a "hot zone" in the shallow crust (incubation time). This implies that nearly 1/3 of the pluton (400m) is emplaced by a subsequent and sustained magmatic activity occurring on a short time scale at the very beginning of the system. (2) Once incubation time is achieved, the calculations show that a small hot zone is created at the base of the sill pile, where new injections stay above their solidus T°C and may interact and differentiate. Extraction of differentiated residual liquids might eventually take place and mix with newly injected magma as documented in active syn-emplacement shear-zones within the "warm" part of the pluton. (3) Finally, the model show that in order to maintain a permanent hot zone at shallow level, injection rate must be of 0.03 m/y with injection of 5m thick basaltic sills eveiy 130yr, imply¬ing formation of a 15 km thick pluton. As this thickness is in contradiction with the one calculated for SJDD (1.5 Km) and exceed much the average thickness observed for many shallow level plutons, I infer that there is no permanent hot zone (or magma chambers) at such shallow level. I rather propose formation of small, ephemeral (10-15yr) reservoirs, which represent only small portions of the final size of the pluton. Thermal calculations show that, in the case of SJDD, 5m thick basaltic sills emplaced every 1500 y, allow formation of such ephemeral reservoirs. The latter are formed by several sills, which are in a mushy state and may interact and differentiate during a short time.The mineralogical, chemical and isotopic data presented in this study suggest a signature intermediate be¬tween E-MORB- and arc-like for the SJDD mafic sills and feeder dykes. The mantle source involved produced hydrated magmas and may be astenosphere modified by "arc-type" components, probably related to a sub¬ducting slab. Combined fluid mobile/immobile trace elements and Sr-Nd isotopes suggest that such subduc¬tion components are mainly fluids derived from altered oceanic crust with minor effect from the subducted sediments. Close match between the SJDD compositions and BABB may point to a continental back-arc setting with little crustal contamination. If so, the SjDD intrusion is a major witness of an extensional tectonic regime during the Early-Carboniferous, linked to the subduction of the Rheno-Hercynian Ocean beneath the Variscan terranes. Also of interest is the unusual association of cogenetic (same isotopic compositions) K-feldspar A- type granite and albite-granite. A-type granites may form by magma mixing between the mafic magma and crustal melts. Alternatively, they might derive from the melting of a biotite-bearing quartz-feldspathic crustal protolith triggered by early mafic injections at low crustal levels. Albite-granite may form by plagioclase cu¬mulate remelting issued from A-type magma differentiation.

Comparison of molecular signatures from multiple skin diseases identifies mechanisms of immunopathogenesis.

The ability to obtain gene expression profiles from human disease specimens provides an opportunity to identify relevant gene pathways, but is limited by the absence of data sets spanning a broad range of conditions. Here, we analyzed publicly available microarray data from 16 diverse skin conditions in order to gain insight into disease pathogenesis. Unsupervised hierarchical clustering separated samples by disease as well as common cellular and molecular pathways. Disease-specific signatures were leveraged to build a multi-disease classifier, which predicted the diagnosis of publicly and prospectively collected expression profiles with 93% accuracy. In one sample, the molecular classifier differed from the initial clinical diagnosis and correctly predicted the eventual diagnosis as the clinical presentation evolved. Finally, integration of IFN-regulated gene programs with the skin database revealed a significant inverse correlation between IFN-β and IFN-γ programs across all conditions. Our study provides an integrative approach to the study of gene signatures from multiple skin conditions, elucidating mechanisms of disease pathogenesis. In addition, these studies provide a framework for developing tools for personalized medicine toward the precise prediction, prevention, and treatment of disease on an individual level.

General electromagnetic simulation tool to predict the microwave nonlinear response of planar, arbitrarily-shaped HTS structures

This work describes a simulation tool being developed at UPC to predict the microwave nonlinear behavior of planar superconducting structures with very few restrictions on the geometry of the planar layout. The software is intended to be applicable to most structures used in planar HTS circuits, including line, patch, and quasi-lumped microstrip resonators. The tool combines Method of Moments (MoM) algorithms for general electromagnetic simulation with Harmonic Balance algorithms to take into account the nonlinearities in the HTS material. The Method of Moments code is based on discretization of the Electric Field Integral Equation in Rao, Wilton and Glisson Basis Functions. The multilayer dyadic Green's function is used with Sommerfeld integral formulation. The Harmonic Balance algorithm has been adapted to this application where the nonlinearity is distributed and where compatibility with the MoM algorithm is required. Tests of the algorithm in TM010 disk resonators agree with closed-form equations for both the fundamental and third-order intermodulation currents. Simulations of hairpin resonators show good qualitative agreement with previously published results, but it is found that a finer meshing would be necessary to get correct quantitative results. Possible improvements are suggested.

Growth mechanisms and timing of emplacement of a vertically layered mafic intrusion in the feeder zone of an ocean island volcano (Fuerteventura, Canary islands)

Résumé pour le grand public L'île de Fuerteventura (Canaries) offre l'occasion rare d'observer les racines d'un volcan océanique édifié il y a 25 à 30 millions d'années et complètement érodé. On y voit de nombreux petits plutons de forme et composition variées, témoignant d'autant d'épisodes de l'activité magmatique. L'un de ces plutons, appelé PX1, présente une structure inhabituelle formée d'une alternance de bandes verticales d'épaisseur métrique à hectométrique de roches sombres de composition pyroxénilique ou gabbroïque. Les pyroxénites résultent clairement de l'accumulation de cristaux de pyroxènes et non de la simple solidification d'un magma? Se pose dès lors la question de la nature du processus qui a conduit à l'accumulation verticale de niveaux concentrés en pyroxènes. En effet, les litages pyroxénitiques classiques sont subhorizontaux, car ils résultent de l'accumulation gravitaire des cristaux séparés du magma dont ils cristalli¬sent par sédimentation. Cette étude vise à identifier et comprendre les mécanismes qui ont engendré ce Iitage minéralogique vertical et l'im¬portant volume de ces faciès cumulatifs. Nous nous sommes également intéressés aux conditions de pression et de température régnant au moment de la mise en place du pluton, ainsi qu'à sa durée de vie et à sa vitesse de refroidis¬sement. Enfin une approche géochimique nous a permis de préciser la nature de la source mantellique des magmas liés à cette activité magmatique. PX1 est en réalité un complexe filonien formé à des conditions de pression et de température de 1-2 kbar et 1050- 1100°C; sa construction a nécessité au moins 150 km3 de magma. L'alternance d'horizons gabbroïques et pyroxéniti¬ques représente des injections successives de magma sous la forme de filons verticaux, mis en place dans un contexte régional en extension. L'étude des orientations des minéraux dans ces faciès révèle que les horizons gabbroïques enregistrent l'extension régionale, alors que les pyroxénites sont générées par une compaction au sein du pluton. Ceci suggère que le régime des contraintes, qui était extensif lors de l'initiation de la mise en place de PX1, est pério¬diquement devenu compressif au sein même du pluton. Cette compression serait liée à des cycles de mise en place où la vitesse de croissance du pluton dépassait celle de l'extension régionale. La différenciation observée au sein de chaque horizon, depuis des pyroxénites riches en olivine jusqu'à des pyroxé¬nites à plagioclase interstitiel et des gabbros, ainsi que la composition géochimique des minéraux qui les constituent suggèrent que chaque filon vertical s'est mis en place à partir d'un magma de composition identique, puis a évolué indépendamment des autres en fonction du régime thermique et du régime des contraintes local. Lorsque le magma en train de cristalliser s'est trouvé en compression, le liquide résiduel a été séparé des cristaux déjà formés et extrait du système, laissant derrière lui une accumulation de cristaux dont la nature et les proportions dépendaient du stade de cristallisation atteint par le magma au moment de l'extraction. Ainsi, les niveaux de pyroxénites à olivine (premier minéral à cristalliser) ont été formés lorsque le magma correspondant était encore peu cristallisé; à l'inverse, les py¬roxénites riches en plagioclase (minéral plus tardif dans la séquence de cristallisation) et certains gabbros à caractère cumulatif résultent d'une compression tardive dans le processus de cristallisation du filon concerné. Les liquides résiduels extraits des niveaux pyroxénitiques sont rarement observés dans PX1, certaines poches et filonets de com¬position anorthositique pourraient en être les témoins. L'essentiel de ces liquides a probablement gagné des niveaux supérieurs du pluton, voire la surface du volcan. L'origine du régime compressif périodique affectant les filons en voie de cristallisation est attribuée aux injections suivantes de magma au sein du pluton, qui se sont succédées à un rythme plus rapide que la vitesse de consolidation des filons. Des datations U/Pb de haute précision sur des cristaux de zircon et de baddeleyite ainsi que40Ar/39Ar sur des cris¬taux d'amphibole révèlent une initiation de la mise en place de PX1 il y a 22.1 ± 0,7 Ma; celle-ci a duré quelque 0,48 ± 0,22 à 0,52 ± 0,29 Ma. Ce laps de temps est compatible avec celui nécessaire à la cristallisation des filons individuels, qui va de moins d'une année lors de l'initiation du magmatisme à 5 ans lors du maximum d'activité de PX1. La présence de cristaux résorbés enregistrant une cristallisation complexe suggère l'existence d'une chambre mag¬matique convective sous-jacente à PX1 et périodiquement rechargée. Les compositions isotopiques des roches étu¬diées révèlent une source mantellique profonde de type point chaud avec une contribution du manteau lithosphéri- que métasomatisé présent sous les îles Canaries. Résumé L'intrusion mafique Miocène PX1 fait partie du soubassement superficiel (0.15-0.2 GPa, 1100 °Q d'un volcan d'île océanique. La particularité de ce pluton est l'existence d'alternances d'unités de gabbros et de pyroxénites qui met¬tent en évidence un litage magmatique vertical (NNE-SSW). Les horizons gabbroiques et pyroxénitiques sont constitués d'unités de différenciation métriques qui suggèrent tine mise en place par injections périodiques de filons verticaux de magma formant un complexe filonien. Chaque filon vertical a subi une différenciation parallèle à un front de solidification sub-vertical parallèle aux bords du filon. Les pyroxénites résultent du fractionnement et de l'accumulation d'olivine ± clinopyroxene ± plagioclase à partir d'un magma basaltique faiblement alcalin et sont interprétées comme étant des imités de différenciation tronquées dont le liquide interstitiel a été extrait par compaction. L'orientation préférentielle des clinopyroxènes dans ces pyroxe- nites (obtenues par analyse EBSD et micro-tomographique) révèle une composante de cisaillement simple dans la genèse de ces roches, ce qui confirme cette interprétation. La compaction des pyroxénites est probablement causée par a mise en place de filons de magma suivants. Le liquide interstitiel expulsé est probablement par ces derniers. Les clinopyroxènes des gabbros, montrent une composante de cisaillement pure suggérant qu'ils sont affectés par une déformation syn-magmatique parallèle aux zones de cisaillement NNE-SSW observées autour de PX1 et liées au contexte tectonique Miocène d'extension régionale. Ceci suggère que les gabbros sont liés à des taux de mise en place faibles à la fin de cycles d'activité magmatique et sont peu ou pas affectés par la compaction. L'initiation et la géométrie de PX1 sont donc contrôlées par le contexte tectonique régional d'extension alors que les taux et les volumes de magma dépendent de facteurs liés à la source. Des taux d'injection élevés résultent probable¬ment en une croissance du pluton supérieure à la place crée par cette extension. Dans ce cas de figure, la propagation des nouveaux dykes et l'inaptitude du magma à circuler à travers les anciens dykes cristallisés pourrait causer une augmentation de la pression non-lithostatique sur ces derniers, exprimée par un cisaillement simple et l'expulsion du liquide interstitiel qu'ils contiennent (documenté par les zones de collecte anorthositiques). Les compositions en éléments majeurs et traces des gabbros et pyroxenites de PX1 sont globalement homogènes et dépendent de la nature cumulative des échantillons. Cependant, de petites variations des concentrations en éléments traces ainsi que les teneurs en éléments traces des bordures de clinopyroxenes suggèrent que ces derniers ont subi un processus de rééquilibrage et de cristallisation in situ. L'homogénéité des compositions chimiques des échantillons, ainsi que la présence de grains de clinopyroxene résorbés suggère que le complexe filonien PX1 s'est mis en place au dessus d'une chambre magmatique périodiquement rechargée dans laquelle la convection est efficace. Chaque filon est donc issu d'un même magma, mais a subi une différenciation par cristallisation in situ (jusqu'à 70% de fraction¬nement) indépendamment des autres. Dans ces filons cristallisés, les minéraux cumulatifs subissent un rééquilibrage partiel avec les liquide interstitiel avant que ce dernier ne soit expulsé lors de la compaction (mettant ainsi un terme à la différenciation). Ce modèle de mise en place signifie qu'un minimum de 150Km3 de magma est nécessaire à la genèse de PX1, une partie de ce volume ayant été émis par le 'Central Volcanic Complex' de Fuerteventura. Les rapports isotopiques radiogéniques mesurés révèlent la contribution de trois pôles mantelliques dans la genèse du magma formant PX1. Le mélange de ces pôles HIMU, DMM et EM1 refléterai l'interaction du point chaud Cana¬rien avec un manteau lithosphérique hétérogène métasomatisé. Les petites variations de ces rapports et des teneurs en éléments traces au sein des faciès pourrait refléter des taux de fusion partielle variable de la source, résultant en un échantillonnage variable du manteau lithosphérique métasomatisé lors de son interaction avec le point chaud. Des datations U/Pb de haute précision (TIMS) sur des cristaux de zircon et de baddeleyite extraits de gabbros de PX1 révèlent que l'initiation de la cristallisation du magma a eu lieu il y a 22.10±0.07 Ma et que l'activité magmatique a duré un minimum de 0.48 à 0.52 Ma. Des âges 40Ar/39Ar obtenus sur amphibole sont de 21.9 ± 0.6 à 21.8 ± 0.3 Ma, identiques aux âges U/Pb. La combinaison de ces méthodes de datations, suggère que le temps maximum nécessaire à PX1 pour se refroidir en dessous de la température de fermeture de l'amphibole est de 0.8Ma. Ceci signifie que la durée de vie de PX1 est de 520 000 à 800 000 ans. La coexistence de cristaux de baddeleyite et de zircon dans un gabbro est attribuée à son interaction avec un fluide riche en C02 relâché par les carbonatites encaissantes lors du métamorphisme de contact généré par la mise en place de PX1 environ 160 000 ans après le début de sa mise en place. Les durées de vie obtenue sont en accord avec le modèle de mise en place suggérant une durée de cristallisation poux chaque filon allant de 1 an à 5 ans. Abstract The Miocene PX1 gabbro-pyroxenite intrusion (Fuerteventura, Canary Islands), is interpreted as the shallow-level feeder-zone (0.15-0.2 GPa and 1100-1120°C), to an ocean island volcano. The particularity of PX1 is that it displays a NNE-SSW trending vertical magmatic banding expressed by alternating gabbro and pyroxeriite sequences. The gabbro and pyroxenite sequences consist of metre-thick differentiation units, which suggest emplacement by pe¬riodic injection of magma pulses as vertical dykes that amalgamated, similarly to a sub-volcanic sheeted dyke com¬plex. Individual dykes underwent internal differentiation following a solidification front (favoured by a significant lateral/horizontal thermal gradient) parallel to the dyke edges. Pyroxenitic layers result from the fractionation and accumulation of clinopyroxene ± olivine ± plagioclase crystals from a mildly alkaline basaltic liquid and are interpre¬ted as truncated differentiation sequences, from which residual melts were extracted by compaction. Clinopyroxene mineral orientation in pyroxenites (evidenced by EBSD and micro X-ray tomography analysis) display a marked pure shear component, supporting this interpretation. Compaction and squeezing of the crystal mush is ascribed to the incoming and inflating magma pulses. The resulting expelled interstitial liquid was likely collected and erupted along with the magma flowing through the newly injected dykes. Gabbro sequences represent crystallised coalesced magma batches, emplaced at lower rates at the end of eruptive cycles, and underwent minor melt extraction as evi¬denced by clinopyroxene orientations that record a simple shear component suggesting syn-magmatic deformation parallel to observed NNF.-SSW trending shear-zones induced by the regional tensional Miocene stress-field. The initiation and geometry of PX1 is controlled by the regional extensional tectonic regime whereas rates and vo¬lumes of magma depend on source-related factors. High injection rates are likely to induce intrusion growth rates larger than could be accommodated by the regional extension. In this case, dyke tip geometry and the inability of magma to circulate through previously emplaced and crystallised dykes could result in an increase of non-lithostatic pressure on previously emplaced mushy dyke walls; generating strong pure-shear compaction and interstitial melt expulsion within the feeder-zone as recorded by the cumulitic pyroxenite bands and anorthositic collection zones. The whole-rock major and trace-element chemistry of PX1 gabbros and pyroxenites is globally homogeneous and controlled by the cumulate nature of the samples (i.e. on the modal proportions of olivine, pyroxene, plagioclase and oxides). However, small variations of whole-rock trace-element contents as well as trace-element contents of clinopyroxene rims suggest that in-situ re-equilibration and crystallisation has occurred. Additionally, the global homogeneity and presence of complex zoning of rare resorbed clinopyroxene crystals suggest that the PX1 feeder- zone overlies a periodically replenished and efficiently mixed magma chamber. Each individual dyke of magma thus originated from a compositionally constant mildly alkaline magma and differentiated independently from the others reaching up to 70% fractionation. Following dyke arrest these are affected by interaction with the trapped interstitial liquid prior to its compaction-linked expulsion (thus stopping the differentiation process). This emplacement model implies that minimum amount of approximately 150 km3 of magma is needed to generate PX1, part of it having been erupted through the overlying Central Volcanic Complex of Fuerteventura. The radiogenic isotope ratios of PX1 samples reveal the contribution on three end-members during magma genesis. This mixing of the H1MU, EMI and DMM end-members could reflect the interaction of the deep-seated Canarian mantle plume with a heterogeneous metasomatic and sepentininsed lithospheric mantle. Additionally, the observed trace-element and isotopic variations within the same fades groups could reflect varying degrees of partial melting of the source region, thus tapping more or less large areas of the metasomatised lithospheric mantle during interac¬tion with the plume. High precision ID-TIMS U/Pb zircon and baddeleyite ages from the PX1 gabbro samples, indicate initiation of magma crystallisation at 22.10 ± 0.07 Ma. The magmatic activity lasted a minimum of 0.48 to 0.52 Ma. 40Ar/39Ar amphibole ages are of 21.9 ± 0.6 to 21.8 ± 0.3, identical within errors to the U/Pb ages. The combination of the 40Ar/39Ar and U/Pb datasets imply that the maximum amount of time PX1 took to cool below amphibole Tc is 0.8 Ma, suggesting PX1 lifetime of 520 000 to 800 000 years. On top of this, the coexistence of baddeleyite and zircon in a single sample is ascribed to the interaction of PX1 with C02-rich carbonatite-derived fluids released from the host-rock carbonatites during contact metamorphism 160 000 years after PX1 initiation. These ages are in agreement with the emplacement model, implying a crystallisation time of less than 1 to 5 years for individual dykes.