Modificação de nanopartículas de óxido de ferro por dextranas

A modificação de nanopartículas de óxido de ferro tem sido motivo de diversos estudos devido ao grande potencial em aplicações tecnológicas, em especial a área biomédica, pela aliança das propriedades magnéticas dos óxidos com a funcionalidade que a dextrana confere a esse material. O presente trabalho tem como objetivo sintetizar e caracterizar o sistema óxido de ferro/dextranas. O óxido de ferro foi obtido pela reação de co-precipitação de sais de ferro (II) e ferro (III) - na razão molar 1:2 - com hidróxido de sódio e a modificação das partículas magnéticas se deu por dois métodos: (I) a co-precipitação na presença de dextrana e carboximetil dextrana e (II) a co-precipitação seguida da modificação. Para modificação proposta pelo método (II) se fez necessário enxertar a dextrana em ácido acrílico, utilizando o íon Ce(IV) como iniciador da reação de polimerização. Nessa etapa se averiguou a concentração de iniciador ótima para a síntese e, através da técnica de espectroscopia de infravermelho, se pode confirmar a eficiência do enxerto. A concentração 0,3% de íon Ce(IV) apresentou melhor distribuição de tamanho, obtidos por análises de microscopia eletrônica de varredura e espalhamento de luz dinâmico, sendo escolhida para síntese junto a partícula magnética. A difratometria de raio X permitiu determinar a formação de estrutura cristalina da magnetita e maghemita, que são muito parecidas entre si, porém os espectros de infravermelho apontaram desdobramentos da ligação Fe - O característica da maghemita. A relação Fe2+/ Fe3+ obtida por espectrofotometria também resultou em oxidação. A estabilidade coloidal dos sistemas foi avaliada através de medidas de potencial zeta. A modificação da partícula magnética com carboximetil dextrana foi equivalente para os dois métodos empregados, entretanto a modificação com ...

Avaliação da diluição do DNA extraido de material parafinado para amplificação em PCR

Introduction: Several reasons may lead to the failure of polymerase chain reaction (PCR) using DNA purified from paraffin-embedded materials: presence of inhibitors and degradation of target DNA. DNA dilution will often reduce the concentration of potential inhibitors and still contain enough DNA to allow PCR amplification. Objective: To evaluate the dilution influence of DNA purified from paraffin-embedded materials on β-globin PCR amplification. Material and Method: Paraffin-embedded blocks from 30 patients with oropharynx squamous cell carcinomas, diagnosed and treated at the Oral Oncology Center were selected. DNA extraction was performed using QIAmp minikit (Quiagen). DNA was quantified and evaluated for purity by spectrophotometer analysis. Two groups were formed with different amounts of DNA: group I had the originally extracted DNA and group II had the same DNA, however diluted with ultrapure water addition. PCR was performed in both groups using oligonucleotides for human β-globin gene. Results: For Group I, amplification of the β-globin gene sequence was successful in 33.33% of the samples and for Group II, in 23.33%. Conclusion: Dilution of the DNA extracted of paraffin-embedded materials did not modify statistically the amount of positive samples β-globin gene amplified in PCR, although the results suggest that this is a way to increase the method for efficacy amplification of PCR.

Spectrophotometric evaluation of color changes of esthetic brackets stored in potentially staining solutions

The purpose of this study was to evaluate, in vitro, the chromatic behavior of esthetic brackets stored in potentially staining solutions. The sample were divided into four groups according to the commercial brand and stored in four different solutions (distilled water, cola soda, coffee and mouthrinse) at 37°C for 14 days. Possible color changes measured according to the CIE L*a*b* color system with a spectrophotometer at five intervals of time after storage. The statistical analysis was carried out using ANOVA to 1%, Tukey's tests and decomposition of interactions with a significance level of 5%.The color changes were dependent on the solution, storage time and the brand of brackets. The largest color changes were observed in the G3, followed by G2, G1/G4. The esthetic brackets do not present satisfactory and stable chromatic behavior.

Avaliação da termociclagem sobre a estabilidade de cor de diferentes matizes de resina composta

The objective was to evaluate the effect of thermocycling on the color variation of three different composite resins . We studied was Resin Enamel on 3 levels : ( Esthetic X , Opallis and Venus ) ; Resin Dentin in three levels : ( Esthetic X , Opallis and Venus ) and Thermocycling on level 1 : ( 3,000 cycles ) ; variable was the change of color gauged by spectrophotometry . 60 specimens , subdivided into 6 groups were made : GI - Esthetic X Enamel ; GII - Esthetic X dentin ; GIII - Opallis Enamel ; GIV - Opallis dentin ; GV - Enamel and GVI Venus - Venus dentin . The specimens were prepared with a matrix to standardize samples . The inserts of incrementally resins and polymerized with a halogen light Ultralux unit ( Dabi Atlante , Brazil ) with a power of 450mW / cm ² . After fabrication , underwent color reading with a UV Visible Spectrophotometer reflection , UV -2450 ( Shimadzu , Kyoto , Japan ) , with the changes calculated by the system CIE L * a * b * . Then isolates were stored in artificial saliva at 35 ° C ± 2 ° C during 3 months containers being subjected to the effects of thermal cycling for 3000 cycles over the range of 5C to 55C . Again subjected to chromatic evaluation. For the analysis of the results of color change of the studied resins was applied ANOVA two factors at 5 % . The results showed a statistically equal resins enamel GI and GV ( p = 0.79 ) ; the same was not observed for GI and G III resins , where the color change was higher for resin G III ( p = 0.0000002 ) . The same was observed between G III and GV , where the resin enamel G III showed a statistically superior to the color change ( p = 0.0000005 ) Average . Resins to dentin was there a statistical equality between the materials studied . We conclude that the resins studied change in color and resin enamel G III was the most suffered major color changes after aging by thermocycling .

Ciclamato de sódio em refrigerantes de baixa caloria

Sodium cyclamate contents in the widely consumed low calorie soft drinks were determined. Low calorie soft drinks made from cola, guarana, orange, lemon and grape were analyzed following the technique described by Sjörberg and Alanko (1987), with some modifications. The methodology recovery assays were carried out at three spiked levels, and the average recovery of 92.5% and 110.3% were found in cola and guarana, respectively; and the relative standard deviation was of 3.7%. The average sodium cyclamate contents ranged from 27.1 ± 1.1 (cola A) to 127.3 ± 1.5 mg.100 mL-1 (lemon B), indicating that the acceptable daily intake of the sweetener can be easily exceeded after drinking low calorie beverages. All of the analyzed low calorie soft drinks showed sodium cyclamate contents higher than those stated on the label, ranging from 12.9% (cola A) to 19.0% (lemon B). Among 18 low calorie soft drinks analyzed, only four showed the average sodium cyclamate contents in accordance with the maximum limit permitted by Brazilian legislation, that is 40 mg.100 mL-1 of beverage; and in other samples the sweetener exceeded ranging from 74.8% (orange) to 218.3% (lemon B) above of the limit permitted.

Efeitos do desuso e da deficiência de estrógeno sobre a microarquitetura óssea e suas propriedades biomecânicas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Métodos de coleta de deposição para ensaios de deriva em aplicações aéreas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Teores e quantidade de alguns elementos no córrego Lavapés, sub-bacia do rio Sorocaba, São Paulo, Brasil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo da utilização de serragem de madeira como adsorvente para o tratamento de efluentes têxteis

The Brazilian textile industry has been a highlight in the global economy. Connected with this high economic performance there is the water consumption and the generation of great volumes of wastewater which present high concentrations of dyes and chemical substances. One of the main techniques used in the treatment of textile effluents is adsorption, which has the activated carbon as the main adsorbent. Recently, studies have been developed to find alternative materials to activated carbon and exhibiting good adsorption capacity of dyes. The aim of this work is to study the potential of sawdust as adsorbent of low cost to remove the dye Direct Green 26. The results of this type of dye removal were obtained through the study of adsorption isotherms obtained by spectrophotometry in the UV-visible region analyzed by the Langmuir model. Finally, a comparison was made of these results with those of other adsorbents. Results showed that the average removal of dye, using sawdust, was 78.8% for an initial concentration of 500mg / L and the maximum adsorption capacity of 119mg / g. These results demonstrate the great potential of sawdust as an adsorbent for the dye Direct Green 26.

Arranjo de semeadura da soja sobre o rendimento da cultura e da tecnologia de aplicação de produtos fitossanitários

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da temperatura nas respostas aos biocidas diazinon e carbaril em Dilocarcinus pagei Stimpson, 1861

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Suplementação com levedura de Crômio eleva a concentração sérica de Crômio em bovinos

This study evaluated the effect of daily chromium supplementation at growing doses on serum Cr levels in cattle. Sixty Nellore heifers 2 to 5 years old were randomly assigned to one of four groups (15 heifers/group) fed non-fertilized Brachiaria decumbens pasture. In the control group (Gc), the heifers received a mineral mixture without Cr. In the other groups, heifers received 0.59, 1.19 or 2.38 mg Cr+3/animal/day, groups G8,5, G17 and G34, respectively. Blood samples were collected on days 0, 30 and 60. Serum concentration of chromium was determined by graphite furnace atomic absorption spectrophotometer. The chromium source used was the chromium yeast. The results do not support any significant difference (p>0.05) among serum chromium levels of heifers in groups Gc, G8,5, G17 and G34 at a same observation day. Only effect of supplementation time was detected in group G34. In this group there was significant increase (p<0,05) in the concentration serum chromium 60 days after the beginning of the experiment. Concluded Cr yeast can be used as the source of this mineral element for animals and supplementation with 2.38 mg/ cattle/day was the dose that most increased the serum concentration of Cr in Nellore cattle during the experimental period.

Adjuvantes na deposição de aplicações aéreas e terrestres

The Asian rust currently is the main disease of soybean culture, having as characteristics the difficult control, by start at the bottom of plants where penetration of the droplets is harder. The fine droplets has been used with the intention of improve the penetration and increase efficiency of agrochemicals, but that are losses by drift easily. New products have been developed to increase deposition of the drops at targets. The aim of this work was evaluate the TA- 35 capacity to improving the deposition of fungicides spray solution with or without mineral oil by aerial and ground applications. Was used a factorial 3x2, three spray solutions composed by Priori Xtra (concentrated suspension of azoxystrobin 200 g L-1 + cyproconazole 80 g L-1 ) mixed with adjuvants, Nimbus (emulsifiable concentrate containing aliphatic hydrocarbons 428 g L-1 ) and TA-35 (soluble concentrate containing sodium lauryl ether sulfate, surfactants, sequestering agents and emulsifiers), in aerial and ground applications. In ground applications was used 50 L ha-1 , TXA 8002 VS spray nozzles and on aerials was used 15 L ha-1 , Turboaero atomizer, both applying fine droplets. Was utilized the Brilliant Blue (FD & C n. 1) tracer to determine the deposits. There were used glass slides as targets to collect spray droplets. After to extract the tracer of the targets using distilled water, the samples were analyzed by spectrophotometry, thereby was possible quantify the tracer deposited on each glass slide. A study to evaluate possible losses of the tracer by degradation or retention also was done. The comparative analysis of treatments was done by statistical method "Confidence Interval for Differences Between the Averages" with 95% of confidence degree (IC95%). There was degradation or retention of the tracer between the processes of application of the droplets and the processing of the samples. The deposition averages with the presence of TA-35 were greatest for both sprayers however, there were not significant differences among the treatments. The viability of TA-35 use may consider other parameters or complementary studies.

Construção e validação de um túnel de vento para ensaios de estimativa da deriva em pulverizações agrícolas

The aim of this study was to build and validate a low cost reduced-scale wind tunnel for drift evaluation on pesticide application technology. The work was carried out at the NEMPA - Núcleo de Ensaio de Máquinas e Pneus Agroflorestais (NEMPA), FCA/UNESP, Departamento de Engenharia Rural, Botucatu/SP, Brazil. The wind tunnel main characteristics were an open circuit and a closed working section with a fan blowing air into the tunnel. Screens were fitted downstream after the fan in order to stabilize the air flow on the working section. The tunnel was built with 3.0 mm eucalyptus hardboard, with a total length of 4.8 m and a squared section of 0.56 m. The air flow was provided by a 180 W axial fan. The system was adjusted and calibrated to provide a laminar and stable flow at 2.0 m s-1. Validation studies were carried out by using a Teejet XR 8003 flat fan nozzle at 200 kPa (medium droplets) to apply a spray solutions containing water plus a food dye (Blue FDC) at 0,6% m v-1 mixed with two adjuvants: a polymer based anti drift formulation at 0,06% m v-1 and a sodium lauryl ether sulfate based surfactant at 0,2% v v-1. After a 10-second application the drift was collected on nylon strips transversally fixed along the tunnel at different distances from the nozzle and different high from the bottom part of the tunnel. Drift deposits were evaluated by spectrophotometry. The wind tunnel had low levels of turbulence and high repeatability of the data, which means that the flow was uniform and able to be used for carrying out measures to estimate drift. The validation results showed that the tunnel was effective to enable comparative drift measurements on the spray solution used in this work making possible the evaluation of drift risk potential under those spray technologies. The use of an adjuvant based on a polymer reduced the amount of drift from the nozzle compared to the surfactant.

Caracterização física e química e potencial de deriva de caldas contendo surfatantes em pulverizações agrícolas

The aim of this work was to evaluate the effect of the addition of different surfactants in physical and chemical properties of spray solutions, droplets spectra and drift potential on agricultural spraying. The surfactants and concentrations (v v-1) were: Haiten (0.1%), Antideriva and Intec (0.05% and 0.1%). The following characteristics were analyzed: surface tension, viscosity, density and electric conductivity. The droplet size spectrum was determined by a laser particle analyzer (Mastersizer S®, version 2.15) including measurements of volume medium diameter (VMD), the percent of droplets below 50 and 100 μm (V50 e V100) and index span. In order to estimate the drift potential, a series of wind tunnel tests were performed with a Teejet XR 8003 flat fan nozzle at 200 kPa (medium droplets) used to apply the spray solutions containing water, the adjuvants and a food color dye (Brilliant blue FD & C no 1) at 0,6% m v-1. The drift was collected on nylon strips transversally fixed along the tunnel at different distances from the nozzle and different high from the bottom part of the tunnel. Drift deposits were evaluated by spectrophotometry. The results showed that the addition of adjuvants changed physical and chemical properties of spray solutions in different magnitudes according to the surfactant. Surfactants changed the droplet spectrum and drift potential, indicating that higher VMD and smaller V100 induced higher percentage of drift.