How and why to measure the germination process?

In the last two centuries, papers have been published including measurements of the germination process. High diversity of mathematical expressions has made comparisons between papers and some times the interpretation of results difficult. Thus, in this paper is included a review about measurements of the germination process, with an analysis of the several mathematical expressions included in the specific literature, recovering the history, sense, and limitations of some germination measurements. Among the measurements included in this paper are the germinability, germination time, coefficient of uniformity of germination (CUG), coefficient of variation of the germination time (CVt), germination rate (mean rate, weighted mean rate, coefficient of velocity, germination rate of George, Timson’s index, GV or Czabator’s index; Throneberry and Smith’s method and its adaptations, including Maguire’s rate; ERI or emergence rate index, germination index, and its modifications), uncertainty associated to the distribution of the relative frequency of germination (U), and synchronization index (Z). The limits of the germination measurements were included to make the interpretation and decisions during comparisons easier. Time, rate, homogeneity, and synchrony are aspects that can be measured, informing the dynamics of the germination process. These characteristics are important not only for physiologists and seed technologists, but also for ecologists because it is possible to predict the degree of successful of a species based on the capacity of their harvest seed to spread the germination through time, permitting the recruitment in the environment of some part of the seedlings formed.

Exit times for some processes with normally distributed noise

Denna avhandling handlar om metoder för att hitta begränsningar för det asymptotiska beteendet hos en förväntad uthoppstid från ett område omkring en xpunkt för processer som har normalfördelad störning. I huvudsak behandlas olika typer av autoregressiva processer. Fyra olika metoder används. En metod som använder principen för stora avvikelser samt en metod som jämför uthoppstiden med en återkomsttid ger övre begränsningar för den förväntade uthoppstiden. En martingalmetod och en metod för normalfördelade stokastiska variabler ger undre begränsningar. Metoderna har alla både förtjänster och nackdelar. Genom att kombinera de olika metoderna får man de bästa resultaten. Vi får fram gränsvärdet för det asymptotiska beteendet hos en uthoppstid för den multivariata autoregressiva processen, samt motsvarande gränsvärde för den univariata autoregressiva processen av ordning n.

Adrenocortical tumors in children

Childhood adrenocortical tumors (ACT) are rare. In the USA, only about 25 new cases occur each year. In Southern Brazil, however, approximately 10 times that many cases are diagnosed each year. Most cases occur in the contiguous states of São Paulo and Paraná. The cause of this higher rate has not been identified. Familial genetic predisposition to cancer (p53 mutations) and selected genetic syndromes (Beckwith-Wiedemann syndrome) have been associated with childhood ACT in general but not with the Brazilian counterpart. Most of the affected children are young girls with classic endocrine syndromes (virilizing and/or Cushing). Levels of urinary 17-ketosteroids and plasma dehydroepiandrosterone sulfate (DHEA-S), which are abnormal in approximately 90% of the cases, provide the pivotal clue to a diagnosis of ACT. Typical imaging findings of pediatric ACT consist of a large, well-defined suprarenal tumor containing calcifications with a thin capsule and central necrosis or hemorrhage. The pathologic classification of pediatric ACT is troublesome. Even an experienced pathologist can find it difficult to differentiate carcinoma from adenoma. Surgery is the single most important procedure in the successful treatment of ACT. The role of chemotherapy in the management of childhood ACT has not been established although occasional tumors are responsive to mitotane or cisplatin-containing regimens. Because of the heterogeneity and rarity of the disease, prognostic factors have been difficult to establish in pediatric ACT. Patients with incomplete tumor resection or with metastatic disease at diagnosis have a dismal prognosis. In patients with localized and completely resected tumors, the size of the tumor has predictive value. Patients with large tumors have a much higher relapse rate than those with small tumors.

The Cycle Times of Working Capital: Financial Value Chain Analysis Method

Interest towards working capital management increased among practitioners and researchers because the financial crisis of 2008 caused the deterioration of the general financial situation. The importance of managing working capital effectively increased dramatically during the financial crisis. On one hand, companies highlighted the importance of working capital management as part of short-term financial management to overcome funding difficulties. On the other hand, in academia, it has been highlighted the need to analyze working capital management from a wider perspective namely from the value chain perspective. Previously, academic articles mostly discussed working capital management from a company-centered perspective. The objective of this thesis was to put working capital management in a wider and more academic perspective and present case studies of the value chains of industries as instrumental in theoretical contributions and practical contributions as complementary to theoretical contributions and conclusions. The principal assumption of this thesis is that selffinancing of value chains can be established through effective working capital management. Thus, the thesis introduces the financial value chain analysis method which is employed in the empirical studies. The effectiveness of working capital management of the value chains is studied through the cycle time of working capital. The financial value chain analysis method employed in this study is designed for considering value chain level phenomena. This method provides a holistic picture of the value chain through financial figures. It extends the value chain analysis to the industry level. Working capital management is studied by the cash conversion cycle that measures the length (days) of time a company has funds tied up in working capital, starting from the payment of purchases to the supplier and ending when remittance of sales is received from the customers. The working capital management practices employed in the automotive, pulp and paper and information and communication technology industries have been studied in this research project. Additionally, the Finnish pharmaceutical industry is studied to obtain a deeper understanding of the working capital management of the value chain. The results indicate that the cycle time of working capital is constant in the value chain context over time. The cash conversion cycle of automotive, pulp and paper, and ICT industries are on average 70, 60 and 40 days, respectively. The difference is mainly a consequence of the different cycle time of inventories. The financial crisis of 2008 affected the working capital management of the industries similarly. Both the cycle time of accounts receivable and accounts payable increased between 2008 and 2009. The results suggest that the companies of the automotive, pulp and paper and ICT value chains were not able to self-finance. Results do not indicate the improvement of value chains position in regard to working capital management either. The findings suggest that companies operating in the Finnish pharmaceutical industry are interested in developing their own working capital management, but collaboration with the value chain partners is not considered interesting. Competition no longer occurs between individual companies, but between value chains. Therefore the financial value chain analysis method introduced in this thesis has the potential to support value chains in improving their competitiveness.

Enucleated L929 mouse fibroblasts support invasion and multiplication of Shigella flexneri 5a

Invasive bacteria can induce their own uptake and specify their intracellular localization; hence it is commonly assumed that proximate modulation of host cell transcription is not required for infection. However, bacteria can also modulate, directly or indirectly, the transcription of many host cell genes, whose role in the infection may be difficult to determine by global gene expression. Is the host cell nucleus proximately required for intracellular infection and, if so, for which pathogens and at what stages of infection? Enucleated cells were previously infected with Toxoplasma gondii, Chlamydia psittaci, C. trachomatis, or Rickettsia prowazekii. We enucleated L929 mouse fibroblasts by centrifugation in the presence of cytochalasin B, and compared the infection with Shigella flexneri M90T 5a of nucleated and enucleated cells. Percent infection and bacterial loads were estimated with a gentamicin suppression assay in cultures fixed and stained at different times after infection. Enucleation reduced by about half the percent of infected cells, a finding that may reflect the reduced endocytic ability of L929 cytoplasts. However, average numbers of bacteria and frequency distributions of bacterial numbers per cell at different times were similar in enucleated and nucleated cells. Bacteria with actin-rich tails were detected in both cytoplasts and nucleated cells. Lastly, cytoplasts were similarly infected 2 and 24 h after enucleation, suggesting that short-lived mRNAs were not involved in the infection. Productive S. flexneri infection could thus take place in cells unable to modulate gene transcription, RNA processing, or nucleus-dependent signaling cascades.

Control of attention by a peripheral visual cue depends on whether the target is difficult to discriminate

The influence of a peripheral cue represented by a gray ring on responsivity to a subsequent target varies. When a vertical line inside a ring was a go target and a white small ring inside a ring was a no-go target, reaction time was shorter at the same location relative to a different location. However, no reaction time difference between the two locations occurred when a white cross inside the ring, instead of the white vertical line inside the ring, was the go target. We investigated whether this last finding was due to a forward masking influence of the cue, a requirement of low attention for the discrimination or a lack of attention mobilization by the cue. In Experiment 1, the intensity of the cue was reduced in an attempt to reduce forward masking. In Experiment 2, the vertical line and the cross were presented in the same block of trials so as to be dealt with a common attentional strategy. In Experiments 3 and 4, the no-go target was a 45º rotated cross inside a ring to increase the difficulty of the discrimination. No evidence was obtained that the cross was forward masked by the cue nor that it demanded less attention to be discriminated from the small ring. There was a facilitation of responsivity by the cue when the small ring was replaced by the rotated cross. The results suggest that when the discrimination to be performed is too easy the cue does not mobilize attention.

Intensification of Operation of Inclined Plate Settler at Fertilizer Plant

Fertilizer plant’s process waters contain high concentrations of nitrogen compounds, such as ammonium and nitrate. Phosphorus and fluorine, which originate from phosphoric acid and rock phosphate (apatite) used in fertilizer production, are also present. Phosphorus and nitrogen are the primary nutrients causing eutrophication of surface waters. At fertilizer plant process waters are held in closed internal circulation. In a scrubber system process waters are used for washing exhaust gases from fertilizer reactors and dry gases from granulation drums as well as for cooling down the fertilizer slurry in neutralization reactor. Solids in process waters are separated in an inclined plate settler by gravitational sedimentation. However, the operation of inclined plate settler has been inadequate. The aim of this thesis was to intensify the operation of inclined plate settler and thus the solids separation e.g. through coagulation and/or flocculation process. Chemical precipitation was studied to reduce the amount of dissolved species in process waters. Specific interest was in precipitation of nitrogen, phosphorus, and fluorine containing specimens. Amounts of phosphorus and fluorine were reduced significantly by chemical precipitation. When compared to earlier studies, annual chemical costs were almost eight times lower. Instead, nitrogen compounds are readily dissolved in water, thus being difficult to remove by precipitation. Possible alternative techniques for nitrogen removal are adsorption, ion exchange, and reverse osmosis. Settling velocities of pH adjusted and flocculated process waters were sufficient for the operation of inclined plate settler. Design principles of inclined plate settler are also presented. In continuation studies, flow conditions in inclined plate settler should be modelled with computational fluid dynamics and suitability of adsorbents, ion exchange resins, and membranes should be studied in laboratory scale tests.

Celecoxib reduces symptoms in men with difficult chronic pelvic pain syndrome (Category IIIA)

We investigated the effectiveness of celecoxib in reducing symptoms in patients with difficult chronic pelvic pain syndrome (CPPS), NIH category IIIA. Sixty-four patients with category IIIA CPPS were randomized into two groups of 32 subjects each. One group was treated with celecoxib (200 mg daily) and the other with placebo. All patients underwent treatment for 6 weeks and were evaluated clinically before (baseline) and after 1, 2, 4, 6, and 8 weeks of treatment. The evaluation included the NIH Chronic Prostatitis Symptom Index (NIH-CPSI) and a subjective global assessment (SGA). Repeated measures analysis of variance was used to evaluate treatment and time effects and their interaction. A decrease (means ± SD) in total NIH-CPSI score from 23.91 ± 5.27 to 15.88 ± 2.51 in the celecoxib group and from 24.25 ± 5.09 to 19.50 ± 2.50 in the placebo group was observed during treatment (0 to 6 weeks). A statistically significant decrease was observed in pain subscore (P < 0.006), quality of life subscore (P < 0.032) and total NIH-CPSI score (P < 0.015) after 2, 4 and 6 weeks, but not in urinary subscore. In addition, 38% of the celecoxib and 13% of the placebo subjects had at least a moderate improvement in SGA. The trend was similar for the NIH-CPSI scores. However, the response to treatment in terms of total NIH-CPSI score or subscore was not significantly different from placebo after interruption of treatment for 2 weeks. Our results show that celecoxib provides significant symptomatic improvement limited to the duration of the therapy in patients with difficult category IIIA CPPS compared to placebo.

Lateral asymmetry of voluntary attention orienting

We recently demonstrated that automatic attention favors the right side of space and, in the present study, we investigated whether voluntary attention also favors this side. Six reaction time experiments were conducted. In each experiment, 12 new 18-25-year-old male right-handed individuals were tested. In Experiments 1, 2, 3 (a, b) and 4 (a, b), tasks with increasing attentional demands were used. In Experiments 1, 2, 3a, and 4a, attention was oriented to one or both sides by means of a central spatially informative visual cue. A left or right side visual target appeared 100, 300, or 500 ms later. Attentional effects were observed in the four experiments. In Experiments 2, 3a and 4a, these effects were greater when the cue indicated the right side than when it indicated the left side (respectively: 16 ± 10 and 44 ± 6 ms, P = 0.015, for stimulus onset asynchrony of 500 ms in Experiment 2; 38 ± 10 and 70 ± 7 ms, P = 0.011, for Experiment 3a, and 23 ± 11 and 61 ± 10 ms, P = 0.009, for Experiment 4a). In Experiments 3b and 4b, the central cue pointed to both sides and was said to be non-relevant for task performance. In these experiments right and left reaction times did not differ. The most conservative interpretation of the present findings is that voluntary attention orienting favors the right side of space, particularly when a difficult task has to be performed.

Effect of harvest at different times of day on the physical and chemical characteristics of vegetable-type soybean

The objective of this study was to evaluate the effect of harvest at different times of day on the chemical and physical characteristics of vegetable-type soybean BRS 267 cultivar, harvested at the R6 stage (seed development) and to compare it with that on the grains harvested at the R8 stage (maturation). The pods of the BRS 267 cultivar were harvested at the R6 stage (at 8:00 AM, 12:00 AM, and 6:00 PM), the color parameters were evaluated, and the grains were analyzed for chemical composition, activity inhibitor trypsin, phytic acid content, starch, sugars, fatty acids, and isoflavones. No differences were observed among the different harvest times in terms of the chemical constituents of vegetable-type soybean BRS 267 cultivar harvested at the R6 stage. Isoflavones content did not change with different harvest times, and the aglycone forms (daidzein, glycitein, and genistein) were found in smaller quantities at the R6 stage compared to the R8 stage. The color of the pods of soybean BRS 267 cultivar, harvested at the R6 stage did not change with different harvest times. The grains harvested at the R6 stage had lower protein content, phytic acid, and sucrose and higher levels of lipids, carbohydrates, starch, glucose, fructose, stachyose, and linolenic acids than those collected at the R8 stage. The different times of harvest did not affect the quality of the vegetable-type soybean BRS 267 cultivar harvested at stage R6. Nevertheless, it is recommended to harvest in the morning, when the temperature is milder, like other vegetables, to facilitate and optimize its marketing and in natura consumption.

Rosemary extract and celery-based products used as natural quality enhancers for colonial type salami with different ripening times

This study aimed to evaluate the use of rosemary (Rosmarinus officinalis) extract (RE), celery (Apium graveolis), and low levels of NO3 and NO2 as natural agents to enhance the quality of colonial salami. Salami was produced according to three treatments: (A) Control: 0.1% curing salt; (B) Rosemary: 0.05% curing salt + 0.5% RE (rosemary extract); and (C) Rosemary+celery: 0.14% Veg 503 + 0.27% Veg 504 (sea salt plus celery) + 0.5% of RE (rosemary extract). There was no effect (P > 0.05) of the treatments on water activity, Na content, and residual NO3 and NO2. Fatty acids C18:2 and C20:4 were reduced (P < 0.05) during the ripening period in the Control treatment indicating possible oxidation. The use of celery resulted in lower pH values (P < 0.05) in the salami. Reduced addition of NO3 and NO2 resulted in salami lighter in color (higher L* values, P < 0.05) at the 12th day of ripening. In conclusion, celery-based products proved to be an effective source of NO2 and NO3 for color development, but the low pH of the product indicates the need for better evaluation of its use in fermented salami. The RE (rosemary extract) reduced fat oxidation in salami, but this needs further evaluation.

Quality characteristics of Moroccan sweet paprika (Capsicum annuum L.) at different sampling times

"La Niora" is a red pepper variety cultivated in Tadla Region (Morocco) which is used for manufacturing paprika after sun drying. The paprika quality (nutritional, chemical and microbiological) was evaluated immediately after milling, from September to December. Sampling time mainly affected paprika color and the total capsaicinoid and vitamin C contents. The commercial quality was acceptable and no aflatoxins were found, but the microbial load sometimes exceeded permitted levels.

Effect of Brea Gum on the characteristics of wheat bread at different storage times

The effect of Brea Gum (BG) addition on a basic bread formulation is described. The aim of the study was to investigate the effect of BG on the characteristics of wheat bread in terms of changes in moisture, texture, retrogradation of amylopectin, and microstructure. Bread quality was assessed by the physical parameters (volume, specific volume index, width/height ratio, crumb moisture, color, and hardness) and crumb grain structure (total cell number, total cell area, average size of cells, and number of cells per unit area). The effect of BG on the characteristics of the crumb during 24, 48, and 72 hours of storage was determined according to changes in moisture, hardness, and amylopectin retrogradation. Furthermore, the microstructure of the crumb was analyzed by scanning electron microscopy (SEM). The results show the ability of BG to retain moisture in the bread crumb, which was expressed by the lower hardness of the bread crumbs with the addition of the hydrocolloid at 48 and 72 hours of storage. This effect was also evident in the microstructure.

Underwater Remote Welding Technology for Offshore Structures

The construction of offshore structures, equipment and devices requires a high level of mechanical reliability in terms of strength, toughness and ductility. One major site for mechanical failure, the weld joint region, needs particularly careful examination, and weld joint quality has become a major focus of research in recent times. Underwater welding carried out offshore faces specific challenges affecting the mechanical reliability of constructions completed underwater. The focus of this thesis is on improvement of weld quality of underwater welding using control theory. This research work identifies ways of optimizing the welding process parameters of flux cored arc welding (FCAW) during underwater welding so as to achieve desired weld bead geometry when welding in a water environment. The weld bead geometry has no known linear relationship with the welding process parameters, which makes it difficult to determine a satisfactory weld quality. However, good weld bead geometry is achievable by controlling the welding process parameters. The doctoral dissertation comprises two sections. The first part introduces the topic of the research, discusses the mechanisms of underwater welding and examines the effect of the water environment on the weld quality of wet welding. The second part comprises four research papers examining different aspects of underwater wet welding and its control and optimization. Issues considered include the effects of welding process parameters on weld bead geometry, optimization of FCAW process parameters, and design of a control system for the purpose of achieving a desired bead geometry that can ensure a high level of mechanical reliability in welded joints of offshore structures. Artificial neural network systems and a fuzzy logic controller, which are incorporated in the control system design, and a hybrid of fuzzy and PID controllers are the major control dynamics used. This study contributes to knowledge of possible solutions for achieving similar high weld quality in underwater wet welding as found with welding in air. The study shows that carefully selected steels with very low carbon equivalent and proper control of the welding process parameters are essential in achieving good weld quality. The study provides a platform for further research in underwater welding. It promotes increased awareness of the need to improve the quality of underwater welding for offshore industries and thus minimize the risk of structural defects resulting from poor weld quality.

Valukappaleiden valmistusprosessin kapeikot teräsvalimossa

Teräsvalimon toimitusprosessissa toimitusvarmuus on tärkeä tuotannon tunnusluku. Valimotuotannossa olevien lukuisten muuttujien vuoksi tuotannonsuunnittelu ja läpivirtauksen hallinta on haasteellista. Tuotteiden, valumateriaalien ja näiden yhdistelmien suuri yhtäaikainen määrä tuotannossa vaikeuttaa tuotannon ennustettavuutta sekä vaikuttaa läpivirtaukseen ja toimitusvarmuuteen. Lisäksi tuotannon eri työvaiheissa ilmenevät kapeikot rajoittavat läpivirtausta ja kasvattavat läpimenoaikoja. Kapeikkoja voidaan hyödyntää tuotannonohjauksessa jos kapeikot ovat selkeästi havaittavissa. Kapasiteetin siirtäminen ei-kapeikosta kapeikkoon lisää tuotannon läpivirtausta. Pelkkä kapeikkojen hallinta ei paranna toimitusvarmuutta jos keskeneräisen tuotannon määrä on suuri ja järjestys väärä. Tuotannon työkuormien visuaalisuuden parantaminen kaikilla työvaiheilla antaa mahdollisuuksia ohjata tuotantoa tehokkaammin. Kandidaatintyössä on tarkasteltu teräsvalimon valmistusprosessia ja selvitetty tuotannon eri vaiheissa ilmeneviä kapeikkoja. Selvitystyössä hyödynnettiin TOC-analyysiä. Keskeneräisen tuotannon määrää mitattiin useilla otannoilla eri työvaiheiden kohdalla. Tuloksia analysoimalla löydettiin tuotannon ongelmakohdat ja niihin tarvittavat kehitystoimenpiteet.