Simulation and material calibration of ultra high strength steel (UHSS) S960 welded joint under static tensile test utilizing finite element method (FEM)

The aim of this work was to calibrate the material properties including strength and strain values for different material zones of ultra-high strength steel (UHSS) welded joints under monotonic static loading. The UHSS is heat sensitive and softens by heat due to welding, the affected zone is heat affected zone (HAZ). In this regard, cylindrical specimens were cut out from welded joints of Strenx® 960 MC and Strenx® Tube 960 MH, were examined by tensile test. The hardness values of specimens’ cross section were measured. Using correlations between hardness and strength, initial material properties were obtained. The same size specimen with different zones of material same as real specimen were created and defined in finite element method (FEM) software with commercial brand Abaqus 6.14-1. The loading and boundary conditions were defined considering tensile test values. Using initial material properties made of hardness-strength correlations (true stress-strain values) as Abaqus main input, FEM is utilized to simulate the tensile test process. By comparing FEM Abaqus results with measured results of tensile test, initial material properties will be revised and reused as software input to be fully calibrated in such a way that FEM results and tensile test results deviate minimum. Two type of different S960 were used including 960 MC plates, and structural hollow section 960 MH X-joint. The joint is welded by BöhlerTM X96 filler material. In welded joints, typically the following zones appear: Weld (WEL), Heat affected zone (HAZ) coarse grained (HCG) and fine grained (HFG), annealed zone, and base material (BaM). Results showed that: The HAZ zone is softened due to heat input while welding. For all the specimens, the softened zone’s strength is decreased and makes it a weakest zone where fracture happens while loading. Stress concentration of a notched specimen can represent the properties of notched zone. The load-displacement diagram from FEM modeling matches with the experiments by the calibrated material properties by compromising two correlations of hardness and strength.

Reputational Risk Management as a key element for business continuity and value maximization

This thesis reveals the topic of reputational risk management as a key element for business continuity and value maximization. The purpose of the work is to investigate reputational risk from the side of its definition, management (including legal requirements on this risk category) and measurement and to analyse reputational risk’s impact on business continuity and value maximization. To be able to do this, different respective articles, reports of financial institutions are gathered and constructive summaries and analysis are made. In order to deeply investigate the impact of reputational risk on business continuity and value maximization, it was chosen to study it from three aspects: 1) check the impact of stock valuation of 7 companies that experienced reputational catastrophe / risk, 2) analyse a case study on disagreements in management of reputational risk among case companies and impact on their respective performance, and 3) conduct a survey of financial sector companies in Liechtenstein to see how reputational risk management works in practice. The findings of the research showed a significant impact of reputation decadence on company’s value and trading volume, and showed crucial importance of post-crisis management for the company’s financial performance. The results of the qualitative research based on survey proved that companies consider reputational risk management as a one of the key elements for their business continuity and value maximization.

A Critical Analysis of the Philosophical-Political Element of the Master-Slave Dialectic

ABSTRACT:The section “Lordship and Bondage” in Hegel’s Phenomenology of Spirit offers us, through the criticism of slavery, some indications regarding Hegel’s conception of human nature. In this paper some consequences of this conception for Hegel’s political philosophy are identified and presented. The analysis shows problems may emerge when we analyze some fundamental Hegelian concepts – “recognition” and shows that some “men” – if we take into consideration the way these concepts were defined in the master-slave dialectic. In light of these problems it is pointed out that Hegel’s political philosophy, and also his position regarding slavery, become less cogent and more susceptible to criticism. The last part of the text analyzes some consequences of problems related to the possibility of defining the concepts “recognition” and “men” in terms of Hegel’s model of state.

Peak Force Kelvin Probe Force Microscopy Investigation of ZrO2 Nanocomposites for Hygroelectricity Power Element

ZrO2 nanocomposites were investigated considering their perspective application in hygroelectric power elements. Scanning probe microscopy (SPM) techniques allowed to visualize the surface topography and electrical properties. In this work was compared spacial charge behaviour of sample in humid and dry air conditions. Also different SPM modes were compared. Kelvin probe force microscopy (KPFM) was applied to characterize the spacial charge distribution on surface of the sample. Measurements showed, that trapped charge is not dissipated and can be manipulated with low voltages. Humidity influence on the electric potential of the sample was shown.

The role of cyclic nucleotides in modulation of crayfish neuromuscular junctions by a neuropeptide /

DF2, a heptapeptide, is a member of the family of FMRFamide-like peptides and has been shown to increase the amount of transmitter released at neuromuscular junctions of the crayfish, Procambarus clarkit Recent evidence has shown that protein kinase C (PKC), calcium/calmodulin-dependent protein kinase II (CaMKII) and the cAMPdependent protein kinase (PKA) play a role in the neuromodulatory pathway of DF2. The involvement of these kinases led to the prediction that a G-protein-coupled receptor (GPCR) is activated by DF2 due to the role that each kinase plays in traditional GPCR pathways seen in other organisms and in other cells. G-proteins can also act on an enzyme that generates cyclic guanosine monophosphate (cGMP) which mediates its effects through a cGMP-dependent protein kinase (PKG). This thesis addresses the question of whether or not DF2's effects on synaptic transmission in crayfish are mediated by the cyclic nucleotides cAMP and cGMP. The effects of DF2 on synaptic transmission were examined using deep abdominal extensor muscles of the crayfish Procambarus clarkii. An identified motor neuron was stimulated, and excitatory post-synaptic potentials (EPSPs) were recorded in abdominal extensor muscle LI . A number of activators and inhibitors were used to determine whether or not cAMP, PKA, cGMP and PKG mediate the effect of this peptide. Chemicals that are known to activate PKA (Sp-cAMPS) and/or PKG (8-pCPTcGMP) mimic and potentiate DF2's effect by increasing EPSP amplitude. Inhibitors of either PKA (Rp-cAMPS) or PKG (Rp-8-pCPT-cGMPS) block a portion of the increase in EPSP amplitude induced by the peptide. When both kinase inhibitors are applied simultaneously, the entire effect of DF2 on EPSPs is blocked. The PKG inhibitor blocks the effects of a PKG activator but does not alter the effect of a PKA activator on EPSP amplitude. Thus, the PKG inhibitor appears to be relatively specific for PKG. A trend in the data suggests that the PKA inhibitor blocks a portion of the response elicited by the PKG activator. Thus, the PKA inhibitor may be less specific for PKA. Phosphodiesterase inhibitors, which are known to inhibit the breakdown of cAMP (IBMX) and/or cGMP (mdBAMQ), potentiate the effect of the peptide. These results support the hypothesis that cAMP and cGMP, acting through their respective protein kinase enzymes, mediate the ability of DFi to increase transmitter output.

The sedimentology of the Bloomington fan complex: an element of the Oak Ridges Moraine, Southern Ontario

The Oak Ridges Moraine is a major physiographic feature of south-central Ontario, extending from Rice Lake westward to the Niagara Escarpment. While much previous work has largely postulated a relatively simple the origin of the moraine, recent investigations have concentrated on delineating the discernible glacigenic deposits (or landform architectural elements) which comprise the complex mosaic of the Oak Ridges Moraine. This study investigates the sedimentology of the Bloomington fan complex, one of the oldest elements of the Oak Ridges Moraine. The main sediment body of the Bloomington fan complex was deposited during early stages of the formation of the Oak Ridges Moraine, when the ice subdivided, and formed a confined, interlobate lake basin between the northern and southern lobes. Deposition from several conduits produced a fan complex characterized by multiple, laterally overlapping, fan bodies. It appears that the fans were active sequentially in an eastward direction, until the formation of the Bloomington fan complex was dominated by the largest fan fed by a conduit near the northeastern margin of the deposit. Following deposition of the fan complex, the northern and southern ice margins continued to retreat, opening drainage outlets to the west and causing water levels to drop in the lake basin. Glaciofluvial sediment was deposited at this time, cutting into the underlying fan complex. Re-advancing northern ice then closed westerly outlets, and caused water levels to increase, initiating the re-advance of the southern ice. As the southern ice approached the Bloomington fan, it deposited an ice-marginal sediment complex consisting of glacigenic sediment gravity flows, and glaciolacustrine and glaciofluvial sediments exhibiting north and northwesterly paleocurrents. Continued advance of the southern ice, overriding the fan complex, ii produced large-scale glaciotectonic deformation structures, and deposited the Halton Till. The subaqueous fan depositional model that is postulated for the Bloomington fan complex differs from published models due to the complex facies associations produced by the multiple conduit sources of sediment feeding the fans. The fluctuating northern and southern ice margins, which moved across the study area in opposite directions, controlled the water level in the interlobate basin and caused major changes in depositional environments. The influence of these two lobes also caused deposition from two distinct source directions. Finally, erosion, deposition, and deformation of the deposit with the readvance of the southern ice contributed further to the complexity of the Bloomington fan complex.

Zero-sum problems in finite cyclic groups

The purpose of this thesis is to investigate some open problems in the area of combinatorial number theory referred to as zero-sum theory. A zero-sequence in a finite cyclic group G is said to have the basic property if it is equivalent under group automorphism to one which has sum precisely IGI when this sum is viewed as an integer. This thesis investigates two major problems, the first of which is referred to as the basic pair problem. This problem seeks to determine conditions for which every zero-sequence of a given length in a finite abelian group has the basic property. We resolve an open problem regarding basic pairs in cyclic groups by demonstrating that every sequence of length four in Zp has the basic property, and we conjecture on the complete solution of this problem. The second problem is a 1988 conjecture of Kleitman and Lemke, part of which claims that every sequence of length n in Zn has a subsequence with the basic property. If one considers the special case where n is an odd integer we believe this conjecture to hold true. We verify this is the case for all prime integers less than 40, and all odd integers less than 26. In addition, we resolve the Kleitman-Lemke conjecture for general n in the negative. That is, we demonstrate a sequence in any finite abelian group isomorphic to Z2p (for p ~ 11 a prime) containing no subsequence with the basic property. These results, as well as the results found along the way, contribute to many other problems in zero-sum theory.

SYNTHESIS OF CYCLIC AZOBENZENE ANALOGUES FOR INCORPORATION INTO OLIGONUCLEOTIDES, PEPTIDES AND POLYMERS

(A) In recent years, considerable amount of effort has contributed towards enhancing our understanding of the new photoswitch, cyclic azobenzene, particularly from the theoretical point of view. However, the challenging part with this system was poor efficiency of its synthesis from 2,2’- dinitrodibenzyl and lack of effective methods for further modification which would be useful to incorporate this system into biomolecules as a photoswitch. We report the synthesis of cyclic azobenzene and analogues from 2,2’-dinitrodibenzyl, which would allow for further incorporation of this cyclic azobenzene into biomolecules. Reaction of 2,2’-dinitrodibenzyl with zinc metal powder in the presence of triethylammonium formate buffer (pH-9.5) gave a cyclic azoxybenzene, 11,12-dihydrodibenzo[c,g][1,2]diazocine-5-oxide. The latter compound was converted into cyclic azobenzene analogues (bromo-, chloro-, cyano-, and carboxyl) through subsequent transformations. The carboxylic acid analogue was reacted with D-threoninol to give the corresponding amide, which readily undergoes photo-isomerization upon illumination with light. Upon illumination with light at 400 nm, approximately 70% of cis- isomer of amide was isomerized to trans- isomer. It was observed that cis- to trans- isomerization reached the maximum steady state of light transmission after approximately 40 min, whereas the trans- to cis- isomerization approximately acquired in 2 h to regain full recovery of light transmission. Cyclic azobenzene phosphoramidite was synthesized from DMT-protected D-threoninol linked cyclic azobenzene. (B) In recent years, there has been considerable interest invested towards the synthesis of azobenzene analogues for incorporation into proteins. Among the many azobenzene analogues, the synthesis of bi-functional cyclic azobenzene analogues for the incorporation into proteins is relatively new. In this thesis, we report the synthesis of a cyclic azobenzene biscarboxylic acid from 4-(bromomethyl)benzonitrile. (C) Azobenzene has been widely used in the field of polymer science to study the surface morphology and surface properties of polymers. In this thesis, we report the incorporation of cyclic azobenzene into a commercial polymer 2- (hydroxyethyl)methacrylate. Samples collected after 24 h from the reaction solution showed approximately 9% of incorporation of cyclic azobenzene into polymer compared to samples collected after 10 h, which showed approximately 6% incorporation.

Synthesis of 3', 5'-cyclic diguanylic acid (c-di-GMP) analogues

In the past few years, interest in signaling networks involving 3ʹ, 5ʹ -cyclic diguanylic acid (c-di-GMP) has increased dramatically. Evidence started to emerge that connects c-di-GMP to the regulation of a range of biological processes in bacteria, such as bacterial biofilm formation, virulence, extracellular polysaccharide synthesis, however, much remains to be explored in the signaling pathways that involve this secondary messenger. This molecule has also been shown to be a very powerful immunostimulating agent and potent mucosal vaccine adjuvant.

(A) Photoregulation of DNA Functions by Cyclic Azobenzene-tethered Oligonucleotides (B) Site-specific Fluorescent Labeling of DNA using Inverse Electron Demand Diels-Alder Reaction between trans-Cyclooctene Derivatives and BODIPY-Tetrazine Adducts

(A) Most azobenzene-based photoswitches require UV light for photoisomerization, which limit their applications in biological systems due to possible photodamage. Cyclic azobenzene derivatives, on the other hand, can undergo cis-trans isomerization when exposed to visible light. A shortened synthetic scheme was developed for the preparation of a building block containing cyclic azobenzene and D-threoninol (cAB-Thr). trans-Cyclic azobenzene was found to thermally isomerize back to the cis-form in a temperature-dependent manner. cAB-Thr was transformed into the corresponding phosphoramidite and subsequently incorporated into oligonucleotides by solid phase synthesis. Melting temperature measurement suggested that incorporation of cis-cAB into oligonucleotides destabilizes DNA duplexes, these findings corroborate with circular dichroism measurement. Finally, Fluorescent Energy Resonance Transfer experiments indicated that trans-cAB can be accommodated in DNA duplexes. (B) Inverse Electron Demand Diels-Alder reactions (IEDDA) between trans-olefins and tetrazines provide a powerful alternative to existing ligation chemistries due to its fast reaction rate, bioorthogonality and mutual orthogonality with other click reactions. In this project, an attempt was pursued to synthesize trans-cyclooctene building blocks for oligonucleotide labeling by reacting with BODIPY-tetrazine. Rel-(1R-4E-pR)-cyclooct-4-enol and rel-(1R,8S,9S,4E)-Bicyclo[6.1.0]non-4-ene-9-ylmethanol were synthesized and then transformed into the corresponding propargyl ether. Subsequent Sonogashira reactions between these propargylated compounds with DMT-protected 5-iododeoxyuridine failed to give the desired products. Finally a methodology was pursued for the synthesis of BODIPY-tetrazine conjugates that will be used in future IEDDA reactions with trans-cyclooctene modified oligonucleotides.

Maximal-Element Rationalizability

We examine the maximal-element rationalizability of choice functions with arbitrary do-mains. While rationality formulated in terms of the choice of greatest elements according to a rationalizing relation has been analyzed relatively thoroughly in the earlier litera-ture, this is not the case for maximal-element rationalizability, except when it coincides with greatest-element rationalizability because of properties imposed on the rationalizing relation. We develop necessary and sufficient conditions for maximal-element rationaliz-ability by itself, and for maximal-element rationalizability in conjunction with additional properties of a rationalizing relation such as re exivity, completeness, P-acyclicity, quasi-transitivity, consistency and transitivity.

Lien entre les matrices de transfert de spins et de boucles du modèle de Potts sur le tore

Le lien entre le spectre de la matrice de transfert de la formulation de spins du modèle de Potts critique et celui de la matrice de transfert double-ligne de la formulation de boucles est établi. La relation entre la trace des deux opérateurs est obtenue dans deux représentations de l'algèbre de Temperley-Lieb cyclique, dont la matrice de transfert de boucles est un élément. Le résultat est exprimé en termes des traces modifiées, qui correspondent à des traces effectuées dans le sous-espace de l'espace de représentation des N-liens se transformant selon la m ième représentation irréductible du groupe cyclique. Le mémoire comporte trois chapitres. Dans le premier chapitre, les résultats essentiels concernant les formulations de spins et de boucles du modèle de Potts sont rappelés. Dans le second chapitre, les propriétés de l'algèbre de Temperley-Lieb cyclique et de ses représentations sont étudiées. Enfin, le lien entre les deux traces est construit dans le troisième chapitre. Le résultat final s'apparente à celui obtenu par Richard et Jacobsen en 2007, mais une nouvelle représentation n'ayant pas été étudiée est aussi investiguée.

Quantification de la relation séquence-activité de l’ARN par prédiction de structure tridimensionnelle

Dans un premier temps, nous avons modélisé la structure d’une famille d’ARN avec une grammaire de graphes afin d’identifier les séquences qui en font partie. Plusieurs autres méthodes de modélisation ont été développées, telles que des grammaires stochastiques hors-contexte, des modèles de covariance, des profils de structures secondaires et des réseaux de contraintes. Ces méthodes de modélisation se basent sur la structure secondaire classique comparativement à nos grammaires de graphes qui se basent sur les motifs cycliques de nucléotides. Pour exemplifier notre modèle, nous avons utilisé la boucle E du ribosome qui contient le motif Sarcin-Ricin qui a été largement étudié depuis sa découverte par cristallographie aux rayons X au début des années 90. Nous avons construit une grammaire de graphes pour la structure du motif Sarcin-Ricin et avons dérivé toutes les séquences qui peuvent s’y replier. La pertinence biologique de ces séquences a été confirmée par une comparaison des séquences d’un alignement de plus de 800 séquences ribosomiques bactériennes. Cette comparaison a soulevée des alignements alternatifs pour quelques unes des séquences que nous avons supportés par des prédictions de structures secondaires et tertiaires. Les motifs cycliques de nucléotides ont été observés par les membres de notre laboratoire dans l'ARN dont la structure tertiaire a été résolue expérimentalement. Une étude des séquences et des structures tertiaires de chaque cycle composant la structure du Sarcin-Ricin a révélé que l'espace des séquences dépend grandement des interactions entre tous les nucléotides à proximité dans l’espace tridimensionnel, c’est-à-dire pas uniquement entre deux paires de bases adjacentes. Le nombre de séquences générées par la grammaire de graphes est plus petit que ceux des méthodes basées sur la structure secondaire classique. Cela suggère l’importance du contexte pour la relation entre la séquence et la structure, d’où l’utilisation d’une grammaire de graphes contextuelle plus expressive que les grammaires hors-contexte. Les grammaires de graphes que nous avons développées ne tiennent compte que de la structure tertiaire et négligent les interactions de groupes chimiques spécifiques avec des éléments extra-moléculaires, comme d’autres macromolécules ou ligands. Dans un deuxième temps et pour tenir compte de ces interactions, nous avons développé un modèle qui tient compte de la position des groupes chimiques à la surface des structures tertiaires. L’hypothèse étant que les groupes chimiques à des positions conservées dans des séquences prédéterminées actives, qui sont déplacés dans des séquences inactives pour une fonction précise, ont de plus grandes chances d’être impliqués dans des interactions avec des facteurs. En poursuivant avec l’exemple de la boucle E, nous avons cherché les groupes de cette boucle qui pourraient être impliqués dans des interactions avec des facteurs d'élongation. Une fois les groupes identifiés, on peut prédire par modélisation tridimensionnelle les séquences qui positionnent correctement ces groupes dans leurs structures tertiaires. Il existe quelques modèles pour adresser ce problème, telles que des descripteurs de molécules, des matrices d’adjacences de nucléotides et ceux basé sur la thermodynamique. Cependant, tous ces modèles utilisent une représentation trop simplifiée de la structure d’ARN, ce qui limite leur applicabilité. Nous avons appliqué notre modèle sur les structures tertiaires d’un ensemble de variants d’une séquence d’une instance du Sarcin-Ricin d’un ribosome bactérien. L’équipe de Wool à l’université de Chicago a déjà étudié cette instance expérimentalement en testant la viabilité de 12 variants. Ils ont déterminé 4 variants viables et 8 létaux. Nous avons utilisé cet ensemble de 12 séquences pour l’entraînement de notre modèle et nous avons déterminé un ensemble de propriétés essentielles à leur fonction biologique. Pour chaque variant de l’ensemble d’entraînement nous avons construit des modèles de structures tertiaires. Nous avons ensuite mesuré les charges partielles des atomes exposés sur la surface et encodé cette information dans des vecteurs. Nous avons utilisé l’analyse des composantes principales pour transformer les vecteurs en un ensemble de variables non corrélées, qu’on appelle les composantes principales. En utilisant la distance Euclidienne pondérée et l’algorithme du plus proche voisin, nous avons appliqué la technique du « Leave-One-Out Cross-Validation » pour choisir les meilleurs paramètres pour prédire l’activité d’une nouvelle séquence en la faisant correspondre à ces composantes principales. Finalement, nous avons confirmé le pouvoir prédictif du modèle à l’aide d’un nouvel ensemble de 8 variants dont la viabilité à été vérifiée expérimentalement dans notre laboratoire. En conclusion, les grammaires de graphes permettent de modéliser la relation entre la séquence et la structure d’un élément structural d’ARN, comme la boucle E contenant le motif Sarcin-Ricin du ribosome. Les applications vont de la correction à l’aide à l'alignement de séquences jusqu’au design de séquences ayant une structure prédéterminée. Nous avons également développé un modèle pour tenir compte des interactions spécifiques liées à une fonction biologique donnée, soit avec des facteurs environnants. Notre modèle est basé sur la conservation de l'exposition des groupes chimiques qui sont impliqués dans ces interactions. Ce modèle nous a permis de prédire l’activité biologique d’un ensemble de variants de la boucle E du ribosome qui se lie à des facteurs d'élongation.

Array pattern nulling by element position perturbations using a genetic algorithm

A genetic algorithm has been used for null steering in phased and adaptive arrays . It has been shown that it is possible to steer the array null s precisely to the required interference directions and to achieve any prescribed null depths . A comparison with the results obtained from the analytic solution shows the advantages of using the genetic algorithm for null steering in linear array patterns