Determination of polybrominated diphenyl ethers in water samples from Mendoza River Basin by HS-SPME-GC-MS/MS

Polybrominated diphenyl ethers (PBDEs) are considered persistent organic pollutants because of their ubiquity, persistence and bioaccumulation. Its harmful effects on human health and the environment, has led to its inclusion of the Stockholm Convention. Little information is found about PBDEs in abiotic systems of the South America in open literature. This paper reports the presence and concentration level of four PBDEs congeners in Mendoza River, Argentina. The selected PBDEs were: 2,2',4,4'-tetrabromodiphenyl ether (BDE-47), 2,2',4,4',5-pentabromodiphenyl ether (BDE-99), 2,2',4,4',6-pentabromodiphenyl ether (BDE- 100) and 2,2',4,4',5,5'-hexabromodiphenyl ether (BDE-153). The analytical methodology used was head space-solid phase micro extraction combined with gas chromatographymass spectrometry (HS-SPME-GC-MS/MS). Several variables, including pH, salting out, extraction technique type and extraction time were studied and optimized over the relative response the target analytes. The precision of HS-SPME-GC-MS/MS evaluated over five replicate, leading RSDs values <13%, detection limits (S/N=3) ranging from 0.03 pg ml-1 to 0.12 pg ml-1 and the calibration graph was linear with r2=0.9959. BDE-47 and BDE-100 were the predominant congeners found in the analyzed samples. Their concentrations ranged from not detected to 1.9 pg ml-1 and to 0.5 pg ml-1, respectively.

(Table 3) Concentrations of polybrominated diphenyl ether and congeners in blubber samples from whales, seals and porpoises between 1986-2009

A selection of PBDE congeners was analyzed in pooled blubber samples of pilot whale (Globicephala melas), ringed seal (Phoca hispida), minke whale (Balaenoptera acutorostrata), fin whale (Balaenoptera physalus), harbor porpoise (Phocoena phocoena), hooded seal (Cystophora cristata) and Atlantic white-sided dolphin (Lagenorhynchus acutus), covering a time period of more than 20 years (1986-2009). The analytes were extracted and cleaned-up using open column extraction and multi-layer silica gel column chromatography, and the analysis was performed on a GC-MS system operating in the NCI mode. The highest PBDE levels were found in the toothed whale species pilot whale and white-sided dolphin, and the lowest levels in fin whales and ringed seals. One-sided analyses of variance (ANOVA) followed by Tukey comparisons of means were applied to test for differences between years and sampling areas. Due to inter-year sampling variability, only general comparisons of PBDE concentrations between different sampling areas could be made. Differences in PBDE concentrations between three sampling periods, from 1986 to 2007, were evaluated in samples of pilot whales, ringed seals, white-sided dolphins and hooded seals. The highest PBDE levels were found in samples from the late 1990s or beginning of 2000, possibly reflecting the increase in the global production of technical PBDE mixtures in the 1990s. The levels of BDE #153 and #154 increased relative to the total PBDE concentration in some of the species in recent years, which may indicate an increased relative exposure to higher brominated congeners. In order to assess the effect of measures taken in legally binding international agreements, it is important to continuously monitor POPs such as PBDEs in sub-Arctic and Arctic environments.

Pore water acetate and hydrogen, helium and methane gas concentrations in ODP Leg 204 sediments

Acetate and hydrogen concentrations in pore fluids were measured in samples taken at seven sites from southern Hydrate Ridge (SHR) offshore Oregon, USA. Acetate concentrations ranged from 3.17 to 2515 µM. The maximum acetate concentrations occurred at Site 1251, which was drilled on a slope basin to the east of SHR at depths just above the bottom-simulating reflector (BSR) that marks the boundary of gas hydrate stability. Acetate maxima and localized high acetate concentrations occurred at the BSR at all sites and frequently corresponded with areas of gas hydrate accumulation, suggesting an empirical relationship. Acetate concentrations were typically at a minimum near the seafloor and above the sulfate/methane interface, where sulfate-reducing bacteria may consume acetate. Hydrogen concentrations in pressure core samples ranged from 16.45 to 1036 parts per million by volume (ppmv). In some cases, hydrogen and acetate concentrations were elevated concurrently, suggesting a positive correlation. However, sampling of hydrogen was limited in comparison to acetate, so any relationships between the two analytes, if present, were difficult to discern.

(Table 2) Polybrominated diphenyl ether concentration in blubber samples from whales, seals and porpoises between 1986-2009

A selection of MeO-BDE and BDE congeners were analyzed in pooled blubber samples of pilot whale (Globicephala melas), ringed seal (Phoca hispida), minke whale (Balaenoptera acutorostrata), fin whale (Balaenoptera physalus), harbor porpoise (Phocoena phocoena), hooded seal (Cystophora cristata), and Atlantic white-sided dolphin (Lagenorhynchus acutus), covering a time period of more than 20 years (1986-2009). The analytes were extracted and cleaned-up using open column extraction and multi-layer silica gel column chromatography. The analysis was performed using both low resolution and high resolution GC-MS. MeO-PBDE concentrations relative to total PBDE concentrations varied greatly between sampling periods and species. The highest MeO-PBDE levels were found in the toothed whale species pilot whale and white-sided dolphin, often exceeding the concentration of the most abundant PBDE, BDE-47. The lowest MeO-PBDE levels were found in fin whales and ringed seals. The main MeO-BDE congeners were 6-MeO-BDE47 and 2'-MeO-BDE68. A weak correlation only between BDE47 and its methoxylated analog 6-MeO-BDE47 was found and is indicative of a natural source for MeO-PBDEs.

Simultaneous determination of multiclass emerging contaminants in aquatic plants by ultrasound assisted matrix solid phase dispersion and GC-MS

A multiresidue method was developed for the simultaneous determination of 31 emerging contaminants (pharmaceutical compounds, hormones, personal care products, biocides and flame retardants) in aquatic plants. Analytes were extracted by ultrasound assisted-matrix solid phase dispersion (UA-MSPD) and determined by gas chromatography-mass spectrometry after sylilation. The method was validated for different aquatic plants (Typha angustifolia, Arundo donax and Lemna minor) and a semiaquatic cultivated plant (Oryza sativa) with good recoveries at concentrations of 100 and 25 ng g-1 wet weight, ranging from 70 to 120 %, and low method detection limits (0.3 to 2.2 ng g-1 wet weight). A significant difference of the chromatographic response was observed for some compounds in neat solvent versus matrix extracts and therefore quantification was carried out using matrix-matched standards in order to overcome this matrix effect. Aquatic plants taken from rivers located at three Spanish regions were analyzed and the compounds detected were parabens, bisphenol A, benzophenone-3, cyfluthrin and cypermethrin. The levels found ranged from 6 to 25 ng g-1 wet weight except for cypermethrin that was detected at 235 ng g-1 wet weight in Oryza sativa samples.

Immunoassays with rolling circle DNA amplification: A versatile platform for ultrasensitive antigen detection

We describe an adaptation of the rolling circle amplification (RCA) reporter system for the detection of protein Ags, termed “immunoRCA.” In immunoRCA, an oligonucleotide primer is covalently attached to an Ab; thus, in the presence of circular DNA, DNA polymerase, and nucleotides, amplification results in a long DNA molecule containing hundreds of copies of the circular DNA sequence that remain attached to the Ab and that can be detected in a variety of ways. Using immunoRCA, analytes were detected at sensitivities exceeding those of conventional enzyme immunoassays in ELISA and microparticle formats. The signal amplification afforded by immunoRCA also enabled immunoassays to be carried out in microspot and microarray formats with exquisite sensitivity. When Ags are present at concentrations down to fM levels, specifically bound Abs can be scored by counting discrete fluorescent signals arising from individual Ag–Ab complexes. Multiplex immunoRCA also was demonstrated by accurately quantifying Ags mixed in different ratios in a two-color, single-molecule-counting assay on a glass slide. ImmunoRCA thus combines high sensitivity and a very wide dynamic range with an unprecedented capability for single molecule detection. This Ag-detection method is of general applicability and is extendable to multiplexed immunoassays that employ a battery of different Abs, each labeled with a unique oligonucleotide primer, that can be discriminated by a color-coded visualization system. ImmunoRCA-profiling based on the simultaneous quantitation of multiple Ags should expand the power of immunoassays by exploiting the increased information content of ratio-based expression analysis.

Application of capillary electrophoresis-electrospray ionization mass spectometry in the determination of molecular diversity.

By means of capillary electrophoresis coupled online to electrospray ionization MS, a library of theoretically 171 disubstituted xanthene derivatives was analyzed. The method allowed the purity and makeup of the library to be determined: 160 of the expected compounds were found to be present, and 12 side-products were also detected in the mixture. Due to the ability of capillary electrophoresis to separate analytes on the basis of charge, most of the xanthene derivatives could be resolved by simple capillary electrophoresis-MS procedures even though 124 of the 171 theoretical compounds were isobaric with at least one other molecule in the mixture. Any remaining unresolved peaks were resolved by MS/MS experiments. The method shows promise for the analysis of small combinatorial libraries with fewer than 1000 components.

Preparação e caracterização de nanopartículas de prata para aplicação no desenvolvimento de imunoensaio para imunoglobulina G humana

Neste trabalho, anticorpos anti-IgGh foram conjugados às nanopartículas de prata (NPAg) para detectar imunoglobulina G humana (IgGh). Um imunoensaio colorimétrico baseado na diminuição da agregação devido ao aumento da repulsão eletrostática após a interação ligante-alvo. A agregação é induzida pela variação da força iônica e uma mudança da coloração da suspensão coloidal de amarelo para vermelho pode ser observada. Na presença de IgGh, a agregação é inibida e a coloração da suspensão coloidal não se altera. As nanopartículas foram obtidas por meio de cinco procedimentos diferentes e caracterizadas por espectroscopia UV-Vis, espalhamento dinâmico de luz, difração de raios-X e microscopia eletrônica. Glicose e borohidreto de sódio foram utilizados como agentes redutores, enquanto CTAB e β-ciclodextrina foram utilizados como estabilizantes. Citrato de sódio foi utilizado como agente redutor e/ou estabilizante. Nanoesferas de carbono foram obtidas por tratamento hidrotérmico de uma solução aquosa de glicose e também foram utilizadas no preparo das nanopartículas. As nanopartículas foram funcionalizadas com ácido mercaptossuccínico e a conjugação ocorreu devido à interação entre grupos aminas e grupos carboxílicos ionizados, presentes no anticorpo e agente de acoplamento, respectivamente. A estabilidade dos conjugados e o efeito da adição de IgGh foram avaliados para todos os sistemas preparados. As nanopartículas de prata preparadas com borohidreto de sódio e citrato de sódio foram selecionadas para serem aplicadas no desenvolvimento do imunoensaio e as condições experimentais foram avaliadas. Em condições ótimas, observou-se uma correlação linear entre a diminuição da agregação do sistema (NPAg-anti-IgGh) e a concentração de IgGh (0 a 200 ng mL-1). O limite de detecção foi estimado em 25 ng mL-1. O método colorimétrico apresentou boa seletividade para a detecção de IgGh. Além disso, foi obtido um resultado satisfatório ao aplicar o método para determinação do fator IX de coagulação. Foi desenvolvido também um método para determinação de ATP baseado na agregação de nanopartículas de ouro. Aptâmeros foram utilizados como elemento de reconhecimento. Em princípio, o método pode ser aplicável à determinação de outros analitos, por meio da substituição do aptâmero utilizado neste trabalho pelo oligonucleotídeo específico para o alvo de interesse.

Diagnóstico da exposição fetal ao álcool através de biomarcadores em mecônio

A grande prevalência do consumo de álcool por mulheres em idade reprodutiva aliada à gravidez não planejada expõe a gestante a um elevado risco de se alcoolizar em algum momento da gestação, principalmente no início do período gestacional em que a maioria delas ainda não tomou ciência do fato. Assim, torna-se extremamente relevante o desenvolvimento de métodos de detecção precoce de recém-nascidos em risco de desenvolvimento de problemas do espectro dos transtornos relacionados à exposição fetal ao álcool. O objetivo desse estudo foi desenvolver, validar e avaliar a eficácia de um método de quantificação de ésteres etílicos de ácidos graxos (FAEEs) no mecônio de recém-nascidos para avaliação da exposição fetal ao álcool. Os FAEEs avaliados foram: palmitato de etila, estearato de etila, oleato de etila e linoleato de etila.O método consistiu no preparo das amostras pela extração líquido-líquido utilizando água, acetona e hexano, seguida de extração em fase sólida empregando cartuchos de aminopropilsilica. A separação e quantificação dos analitos foi realizada por cromatografia em fase gasosa acoplada à espectrometria de massas. Os limites de quantificação (LQ) variaram entre 50-100ng/g. A curva de calibração foi linear de LQ até 2000ng/g para todos os analitos. A recuperação variou de 69,79% a 106,57%. Os analitos demonstraram estabilidade no ensaio de pós-processamento e em solução. O método foi aplicado em amostras de mecônio de 160 recém-nascidos recrutados em uma maternidade pública de Ribeirão Preto-SP. O consumo de álcool materno foi reportado utilizando questionários de rastreamento validados T-ACE e AUDIT e relatos retrospectivos da quantidade e frequência de álcool consumida ao longo da gestação. A eficácia do método analítico em identificar os casos positivos foi determinada pela curva Receiver Operating Characteristic (ROC). O consumo alcoólico de risco foi identificado pelo T-ACE em 31,3% das participantes e 50% reportaram o uso de álcool durante a gestação. 51,3% dos recém-nascidos apresentaram FAEEs em seu mecônio, sendo que 33,1% apresentaram altas concentrações para a somatória dos FAEEs (maior que 500ng/g), compatível com um consumo abusivo de álcool. O oleato de etila foi o biomarcador mais prevalente e o linoleato de etila foi o biomarcador que apresentou as maiores concentrações. Houve uma variabilidade no perfil de distribuição dos FAEEs entre os indivíduos, e discordâncias entre a presença de FAEEs e o consumo reportado pela mãe. A concentração total dos FAEEs nos mecônio mostrou-se como melhor indicador da exposição fetal ao álcool quando comparado com o uso de um único biomarcador. O ponto de corte para esta população foi de aproximadamente 600ng/g para uso tipo binge (três ou mais doses por ocasião) com sensibilidade de 71,43% e especificidade de 84,37%. Este estudo reforça a importância da utilização de métodos laboratoriais na identificação da exposição fetal ao álcool.

Avaliação sistemática do uso do Dried Blood Spot para determinação de elementos químicos em sangue capilar visando estudos de biomonitoramento no Brasil

A biomonitorização humana ou biomonitoramento (BH) é definido como a medida periódica de determinada substância química ou seu metabólito em fluidos biológicos, principalmente sangue e urina, de uma população com o objetivo de avaliar a exposição e os riscos à saúde. Tal método tem se tornado comum em países desenvolvidos, porém ainda é uma prática pouco utilizada no Brasil. Isso ocorre pela dificuldade de coleta, armazenamento e transporte das amostras, principalmente em regiões sem infraestrutura e de difícil acesso. Diante disso, alguns procedimentos alternativos de coleta de amostra vêm sendo propostos. Um destes procedimentos é o Dried Blood Spot (DBS) ou coleta e armazenamento de amostra em papel-cartão. Este método oferece uma série de vantagens sobre os procedimentos de coleta convencionais, principalmente por reduzir consideravelmente o volume de amostra coletada. Entretanto, pouco se sabe sobre a estabilidade dos analitos após a deposição da amostra no cartão e do risco de contaminação da amostra pelo substrato sólido. Além disso, procedimentos de extração dos analitos do papel, para posterior quantificação, ainda não estão totalmente estabelecidos. Neste sentido, o presente trabalho avaliou de forma sistemática o procedimento de coleta de sangue por DBS visando sua futura aplicação em programas de biomonitoramento no Brasil para determinação dos elementos químicos As, Cd, Cu, Hg, Mn, Pb, Se e Zn por espectrometria de massas com plasma indutivamente acoplado (ICP-MS). Para isso, no estudo foram utilizadas três diferentes marcas comerciais de cartão coletor: Whatman 903(TM), Munktell(TM), e DMPK-C(TM). Todas as marcas de cartão apresentaram baixas concentrações dos elementos químicos. Após a deposição da amostra no papel cartão verificou-se que a concentração dos elementos químicos manteve-se estável por um período de pelo menos 60 dias (temperatura ambiente e ao abrigo da luz). Foi otimizado o método de extração dos analitos do substrato, com melhor condição obtida após a imersão do papel (corte circular de diâmetro de 1/2´´) por 60 minutos em solução extratora (0,5% v/v HNO3 e 0,01% v/v Triton(TM) X-100) na proporção de 1:50 v/v, seguida de 10 segundos de agitação por vortex. Após a extração, a solução resultante contendo os analitos foi diretamente injetada no ICP-MS. Cabe também destacar que não foram observadas diferenças estatísticas nas concentrações dos elementos químicos com coleta de sangue da veia do antebraço (sangue venoso) ou do dedo (sangue capilar). Os resultados obtidos no presente estudo, devem contribuir para a implementação deste procedimento em análises de elementos químicos (biomonitoramento da população brasileira), principalmente considerando as dificuldades de coleta, armazenamento e transporte de amostras clínicas em nosso país por sua extensão territorial. Além disso, este procedimento pode facilitar estudos com populações vulneráveis e que vivem em áreas remotas e de difícil acesso.

On-line microwave-based preconcentration device for inductively coupled plasma atomic emission spectrometry: Application to the elemental analysis of spirit samples

A microwave-based thermal nebulizer (MWTN) has been employed for the first time as on-line preconcentration device in inductively coupled plasma atomic emission spectrometry (ICP-AES). By the appropriate selection of the experimental conditions, the MWTN could be either operated as a conventional thermal nebulizer or as on-line analyte preconcentration and nebulization device. Thus, when operating at microwave power values above 100 W and highly concentrated alcohol solutions, the amount of energy per solvent mass liquid unit (EMR) is high enough to completely evaporate the solvent inside the system and, as a consequence, the analyte is deposited (and then preconcentrated) on the inner walls of the MWTN capillary. When reducing the EMR to the appropriate value (e.g., by reducing the microwave power at a constant sample uptake rate) the retained analyte is swept along by the liquid-gas stream and an analyte-enriched aerosol is generated and next introduced into the plasma cell. Emission signals obtained with the MWTN operating in preconcentration-nebulization mode improved when increasing preconcentration time and sample uptake rate as well as when decreasing the nozzle inner diameter. When running with pure ethanol solution at its optimum experimental conditions, the MWTN in preconcentration-nebulization mode afforded limits of detection up to one order of magnitude lowers than those obtained operating the MWTN exclusively as a nebulizer. To validate the method, the multi-element analysis (i.e. Al, Ca, Cd, Cr, Cu, Fe, K, Mg, Mn, Na, Pb and Zn) of different commercial spirit samples in ICP-AES has been performed. Analyte recoveries for all the elements studied ranged between 93% and 107% and the dynamic linear range covered up to 4 orders of magnitude (i.e. from 0.1 to 1000 μg L−1). In these analysis, both MWTN operating modes afforded similar results. Nevertheless, the preconcentration-nebulization mode permits to determine a higher number of analytes due to its higher detection capabilities.

Quaternary ammonium-functionalized silica sorbents for the solid-phase extraction of aromatic amines under normal phase conditions

Quaternary ammonium-functionalized silica materials were synthesized and applied for solid-phase extraction (SPE) of aromatic amines, which are classified as priority pollutants by US Environmental Protection Agency. Hexamethylenetetramine used for silica surface modification for the first time was employed as SPE sorbent under normal phase conditions. Hexaminium-functionalized silica demonstrated excellent extraction efficiencies for o-toluidine, 4-ethylaniline and quinoline (recoveries 101–107%), while for N,N-dimethylaniline and N-isopropylaniline recoveries were from low to moderate (14–46%). In addition, the suitability of 1-alkyl-3-(propyl-3-sulfonate) imidazolium-functionalized silica as SPE sorbent was tested under normal phase conditions. The recoveries achieved for the five aromatic amines ranged from 89 to 99%. The stability of the sorbent was evaluated during and after 150 extractions. Coefficients of variation between 4.5 and 10.2% proved a high stability of the synthesized sorbent. Elution was carried out using acetonitrile in the case of hexaminium-functionalized silica and water for 1-alkyl-3-(propyl-3-sulfonate) imidazolium-functionalized silica sorbent. After the extraction the analytes were separated and detected by liquid chromatography ultraviolet detection (LC-UV). The retention mechanism of the materials was primarily based on polar hydrogen bonding and π–π interactions. Comparison made with activated silica proved the quaternary ammonium-functionalized materials to offer different selectivity and better extraction efficiencies for aromatic amines. Finally, 1-alkyl-3-(propyl-3-sulfonate) imidazolium-functionalized silica sorbent was successfully tested for the extraction of wastewater and soil samples.

Pencil it in: pencil drawn electrochemical sensing platforms

Inspired by recent reports concerning the utilisation of hand drawn pencil macroelectrodes (PDEs), we report the fabrication, characterisation (physicochemical and electrochemical) and implementation (electrochemical sensing) of various PDEs drawn upon a flexible polyester substrate. Electrochemical characterisation reveals that there are no quantifiable electrochemical responses upon utilising these PDEs with an electroactive analyte that requires an electrochemical oxidation step first, therefore the PDEs have been examined towards the electroactive redox probes hexaammineruthenium(III) chloride, potassium ferricyanide and ammonium iron(II) sulfate. For the first time, characterisation of the number of drawn pencil layers and the grade of pencil are examined; these parameters are commonly overlooked when utilising PDEs. It is demonstrated that a PDE drawn ten times with a 6B pencil presented the most advantageous electrochemical platform, in terms of electrochemical reversibility and peak height/analytical signal. In consideration of the aforementioned limitation, analytes requiring an electrochemical reduction as the first process were solely analysed. We demonstrate the beneficial electroanalytical capabilities of these PDEs towards p-benzoquinone and the simultaneous detection of heavy metals, namely lead(II) and cadmium(II), all of which are explored for the first time utilising PDEs. Initially, the detection limits of this system were higher than desired for electroanalytical platforms, however upon implementation of the PDEs in a back-to-back configuration (in which two PDEs are placed back-to-back sharing a single connection to the potentiostat), the detection limits for lead(II) and cadmium(II) correspond to 10 μg L−1 and 98 μg L−1 respectively within model aqueous (0.1 M HCl) solutions.

Synthesis, Modification, and Application of Siloxane Materials for Environmental Sensing

As human populations and resource consumption increase, it is increasingly important to monitor the quality of our environment. While laboratory instruments offer useful information, portable, easy to use sensors would allow environmental analysis to occur on-site, at lower cost, and with minimal operator training. We explore the synthesis, modification, and applications of modified polysiloxane in environmental sensing. Multiple methods of producing modified siloxanes were investigated. Oligomers were formed by using functionalized monomers, producing siloxane materials containing silicon hydride, methyl, and phenyl side chains. Silicon hydride-functionalized oligomers were further modified by hydrosilylation to incorporate methyl ester and naphthyl side chains. Modifications to the siloxane materials were also carried out using post-curing treatments. Methyl ester-functionalized siloxane was incorporated into the surface of a cured poly(dimethylsiloxane) film by siloxane equilibration. The materials containing methyl esters were hydrolyzed to reveal carboxylic acids, which could later be used for covalent protein immobilization. Finally, the siloxane surfaces were modified to incorporate antibodies by covalent, affinity, and adsorption-based attachment. These modifications were characterized by a variety of methods, including contact angle, attenuated total reflectance Fourier transform infrared spectroscopy, dye labels, and 1H nuclear magnetic resonance spectroscopy. The modified siloxane materials were employed in a variety of sensing schemes. Volatile organic compounds were detected using methyl, phenyl, and naphthyl-functionalized materials on a Fabry-Perot interferometer and a refractometer. The Fabry-Perot interferometer was found to detect the analytes upon siloxane extraction by deformation of the Bragg reflectors. The refractometer was used to determine that naphthyl-functionalized siloxanes had elevated refractive indices, rendering these materials more sensitive to some analytes. Antibody-modified siloxanes were used to detect biological analytes through a solid phase microextraction-mediated enzyme linked immunosorbent assay (SPME ELISA). The SPME ELISA was found to have higher analyte sensitivity compared to a conventional ELISA system. The detection scheme was used to detect Escherichia coli at 8500 CFU/mL. These results demonstrate the variety of methods that can be used to modify siloxanes and the wide range of applications of modified siloxanes has been demonstrated through chemical and biological sensing schemes.

Stale flavour volatiles in Australian commercial UHT milk during storage

Methyl ketones, aldehydes and free saturated fatty acids were measured in the headspace of samples of two indirectly processed and two directly processed Australian commercial UHT milks during room temperature storage for 16 weeks. The analytes were isolated using headspace solid phase microextraction and analysed by gas chromatography coupled with flame ionisation detection. All methyl ketones and aldehydes increased during storage, With free saturated fatty acids exhibiting little change. On average, the total methyl ketone and aldehyde concentrations in the indirectly processed UHT milks were higher than those in the directly processed samples. A strong correlation was found between the concentration of methyl ketones and various heat indices (furosine, lactulose and undenatured whey proteins) in the milk samples.