Deformation behaviours of coarse-grained and nanocrystalline Mg-5wt% Al alloys

Magnesium alloys have been of growing interest to various engineering applications, such as the automobile, aerospace, communication and computer industries due to their low density, high specific strength, good machineability and availability as compared with other structural materials. However, most Mg alloys suffer from poor plasticity due to their Hexagonal Close Packed structure. Grain refinement has been proved to be an effective method to enhance the strength and alter the ductility of the materials. Several methods have been proposed to produce materials with nanocrystalline grain structures. So far, most of the research work on nanocrystalline materials has been carried out on Face-Centered Cubic and Body-Centered Cubic metals. However, there has been little investigation of nanocrystalline Mg alloys. In this study, bulk coarse-grained and nanocrystalline Mg alloys were fabricated by a mechanical alloying method. The mixed powder of Mg chips and Al powder was mechanically milled under argon atmosphere for different durations of 0 hours (MA0), 10 hours (MA10), 20 hours (MA20), 30 hours (MA30) and 40 hours (MA40), followed by compaction and sintering. Then the sintered billets were hot-extruded into metallic rods with a 7 mm diameter. The obtained Mg alloys have a nominal composition of Mg–5wt% Al, with grain sizes ranging from 13 μm down to 50 nm, depending on the milling durations. The microstructure characterization and evolution after deformation were carried out by means of Optical microscopy, X-Ray Diffraction, Scanning Electron Microscopy, Transmission Electron Microscopy, Scanning Probe Microscopy and Neutron Diffraction techniques. Nanoindentaion, compression and micro-compression tests on micro-pillars were used to study the size effects on the mechanical behaviour of the Mg alloys. Two kinds of size effects on the mechanical behaviours and deformation mechanisms were investigated: grain size effect and sample size effect. The nanoindentation tests were composed of constant strain rate, constant loading rate and indentation creep tests. The normally reported indentation size effect in single crystal and coarse-grained crystals was observed in both the coarse-grained and nanocrystalline Mg alloys. Since the indentation size effect is correlated to the Geometrically Necessary Dislocations under the indenter to accommodate the plastic deformation, the good agreement between the experimental results and the Indentation Size Effect model indicated that, in the current nanocrystalline MA20 and MA30, the dislocation plasticity was still the dominant deformation mechanism. Significant hardness enhancement with decreasing grain size, down to 58 nm, was found in the nanocrystalline Mg alloys. Further reduction of grain size would lead to a drop in the hardness values. The failure of grain refinement strengthening with the relatively high strain rate sensitivity of nanocrystalline Mg alloys suggested a change in the deformation mechanism. Indentation creep tests showed that the stress exponent was dependent on the loading rate during the loading section of the indentation, which was related to the dislocation structures before the creep starts. The influence of grain size on the mechanical behaviour and strength of extruded coarse-grained and nanocrystalline Mg alloys were investigated using uniaxial compression tests. The macroscopic response of the Mg alloys transited from strain hardening to strain softening behaviour, with grain size reduced from 13 ìm to 50 nm. The strain hardening was related to the twinning induced hardening and dislocation hardening effect, while the strain softening was attributed to the localized deformation in the nanocrystalline grains. The tension–compression yield asymmetry was noticed in the nanocrystalline region, demonstrating the twinning effect in the ultra-fine-grained and nanocrystalline region. The relationship k tensions < k compression failed in the nanocrystalline Mg alloys; this was attributed to the twofold effect of grain size on twinning. The nanocrystalline Mg alloys were found to exhibit increased strain rate sensitivity with decreasing grain size, with strain rate ranging from 0.0001/s to 0.01/s. Strain rate sensitivity of coarse-grained MA0 was increased by more than 10 times in MA40. The Hall-Petch relationship broke down at a critical grain size in the nanocrystalline region. The breakdown of the Hall-Petch relationship and the increased strain rate sensitivity were due to the localized dislocation activities (generalization and annihilation at grain boundaries) and the more significant contribution from grain boundary mediated mechanisms. In the micro-compression tests, the sample size effects on the mechanical behaviours were studied on MA0, MA20 and MA40 micro-pillars. In contrast to the bulk samples under compression, the stress-strain curves of MA0 and MA20 micro-pillars were characterized with a number of discrete strain burst events separated by nearly elastic strain segments. Unlike MA0 and MA20, the stress-strain curves of MA40 micro-pillars were smooth, without obvious strain bursts. The deformation mechanisms of the MA0 and MA20 micro-pillars under micro-compression tests were considered to be initially dominated by deformation twinning, followed by dislocation mechanisms. For MA40 pillars, the deformation mechanisms were believed to be localized dislocation activities and grain boundary related mechanisms. The strain hardening behaviours of the micro-pillars suggested that the grain boundaries in the nanocrystalline micro-pillars would reduce the source (nucleation sources for twins/dislocations) starvation hardening effect. The power law relationship of the yield strength on pillar dimensions in MA0, MA20 supported the fact that the twinning mechanism was correlated to the pre-existing defects, which can promote the nucleation of the twins. Then, we provided a latitudinal comparison of the results and conclusions derived from the different techniques used for testing the coarse-grained and nanocrystalline Mg alloy; this helps to better understand the deformation mechanisms of the Mg alloys as a whole. At the end, we summarized the thesis and highlighted the conclusions, contributions, innovations and outcomes of the research. Finally, it outlined recommendations for future work.

Cost efficiency v quality service : using CHAT as a tool for understanding change and transformation in work practices

This chapter provides an analysis of feedback from key stakeholders, collected as part of a research project, on the problems and tensions evident in the collective work practices of learning advisers employed in learning assistance services at an Australian metropolitan university (Peach, 2003). The term 'learning assistance' is used in the Australian higher education sector generally to refer to student support services that include assistance with academic writing and other study skills. The aim of the study was to help learning advisers and other key stakeholders develop a better understanding of the work activity with a view to using this understanding to generate improvements in service provision. Over twenty problems and associated tensions were identified through stakeholder feedback however the focus of this chapter is the analysis of tensions related to a cluster of problems referred to as cost-efficiency versus quality service. Theoretical modelling derived from the tools made available through cultural historical activity theory and expansive visibilsation (Engestrom and Miettinen, 1999) and excerpts from data are used to illustrate how different understandings of the purpose of learning assistance services impacts on the work practices of learning advisers and creates problems and tensions in relation to the type of service available (including use of technology),level of service available, and learning adviser workload.

Psycho-markers of weight loss. The roles of TFEQ Disinhibition and Restraint in exercise-induced weight management

Eating behaviour traits, namely Disinhibition and Restraint, have the potential to exert an effect on food intake and energy balance. The effectiveness of exercise as a method of weight management could be influenced by these traits. Fifty eight overweight and obese participants completed 12-weeks of supervised exercise. Each participant was prescribed supervised exercise based on an expenditure of 500 kcal/session, 5 d/week for 12-weeks. Following 12-weeks of exercise there was a significant reduction in mean body weight (-3.26 ± 3.63 kg), fat mass (FM: -3.26 ± 2.64 kg), BMI (-1.16 ± 1.17 kg/m2)and waist circumference (WC: -5.0 ± 3.23 cm). Regression analyses revealed a higher baseline Disinhibition score was associated with a greater reduction in BMI and WC, while Internal Disinhibition was associated with a larger decrease in weight, %FM and WC. Neither baseline Restraint or Hunger were associated with any of the anthropometric markers at baseline or after 12-weeks. Furthermore, after 12-weeks of exercise, a decrease in Disinhibition and increase in Restraint were associated with a greater reduction in WC, whereas only Restraint was associated with a decrease in weight. Post-hoc analysis of the sub-factors revealed a decrease in External Disinhibition and increase in Flexible Restraint were associated with weight loss. However, an increase in Rigid Restraint was associated with a reduction in %FM and WC. These findings suggest that exercise-induced weight loss is more marked in individuals with a high level of Disinhibition. These data demonstrate the important roles that Disinhibition and Restraint play in the relationship between exercise and energy balance.

Malnutrition and chemotherapy-induced nausea and vomiting : implications for practice

PURPOSE/OBJECTIVES: To determine the prevalence of malnutrition and chemotherapy-induced nausea and vomiting (CINV) limiting dietary intake in a chemotherapy unit. DESIGN Cross sectional descriptive audit. SETTING: Chemotherapy ambulatory care unit in an Australian teaching hospital. SAMPLE 121 patients receiving chemotherapy for malignancies, ≥18yrs and able to provide verbal consent. METHODS: An Accredited Practicing Dietitian collected all data. Chi-square tests were used to determine the relationship of malnutrition with variables and demographic data. MAIN RESEARCH VARIABLES: Nutritional status, weight change, BMI, prior dietetic input, CINV and CINV that limited dietary intake. FINDINGS Thirty one (26%) participants were malnourished, 12 (10%) had intake-limiting CINV, 22 (20%) reported significant weight loss and 20 (18%) required improved nutrition symptom management. High nutrition risk diagnoses, CINV, BMI and weight loss were significantly associated with malnutrition. Thirteen (35%) participants with malnutrition, significant weight loss, intake-limiting CINV and/or critically requiring improved symptom management reported no dietetic input; the majority of whom were overweight or obese. CONCLUSIONS: This audit determined over one quarter of patients receiving chemotherapy in this ambulatory setting were malnourished and the majority of patients reporting intake-limiting CINV were malnourished. IMPLICATIONS FOR NURSING Patients with malnutrition and/or intake-limiting CINV and in need of improved nutrition symptom management may be overlooked, especially patients who are overweight or obese - an increasing proportion of the Australian population. Evidence-based practice guidelines recommend implementing validated nutrition screening tools, such as the Malnutrition Screening Tool, in patients undergoing chemotherapy to identify those at risk of malnutrition requiring dietitian referral.

Social Procurement: Promoting the sustainability of NPOs through the transformation of economic, social and cultural capital

Social procurement provides a key source of income for the Third Sector, and is vital for the sustainability of many nonprofit organisations. Social procurement involves the exchange of economic capital from one organisation, typically government (although for-profit and non-profit organisations can also purchase), with a nonprofit organisations in order to deliver other forms of. It is this transformation of economic capital into other forms of capital (cultural, human, social) in the social procurement process, which is the focus of this paper. Four case studies, which are representative of the four main types of social procurement, will be examined in order to trace how economic capital is transformed into other types of capital in each of these cases. In so doing, the paper will advance our understanding of social procurement theoretically, and lead to a wider discussion about the role of social procurement in ensuring the sustainability of nonprofit organisations, and the civil societies in which they operate.

Effective adsorption of sodium dodecylsulfate (SDS) by hydrocalumite (CaAl-LDH-Cl) induced by self-dissolution and re-precipitation mechanism

Hydrocalumite (CaAl-LDH-Cl) were synthesized through a rehydration method involving a freshly prepared tricalcium aluminate (C3A) with CaCl2 solution. To understand the intercalation behaviour of sodium dodecylsulfate (SDS) with CaAl-LDH-Cl, X-ray diffraction (XRD), Fourier transform infrared (FTIR), scanning electron microscopy (SEM), transmission electron microscope (TEM), X-ray photoelectron spectroscopy (XPS), inductively coupled plasma-atomic emission spectrometer (ICP) and elemental analysis have been undertaken. The sorption isotherms with SDS reveal that the maximum sorption amount of SDS by CaAl-LDH-Cl could reach 3.67 mmol•g-1. The results revealed that CaAl-LDH-Cl holds a self-dissolution property, about 20-30% of which is dissolved. And the dissolved Ca2+, Al3+ ions are combined with SDS to form CaAl-SDS or Ca-SDS precipitation. It has been highlighted that the composition of resulting products is strongly dependent upon the SDS concentration. With increasing SDS concentrations, the main resulting product changes from CaAl-SDS to Ca-SDS, and the value of interlayer spacing increased to 3.27 nm.

Atomistic exploration of deformation properties of copper nanowires with pre-existing defects

Based on the embedded atom method (EAM) and molecular dynamics (MD) method, in this paper, the tensile deformation properties of Cu nanowires (NWs) with different pre-existing defects, including single surface defects, surface bi-defects and single internal defects, are systematically studied. In-depth deformation mechanisms of NWs with pre-existing defects are also explored. It is found that Young's modulus is insensitive to different pre-existing defects, but yield strength shows an obvious decrease. Defects are observed influencing greatly on NWs' tensile deformation mechanisms, and playing a role of dislocation sources. Besides of the traditional deformation process dominated by the nucleation and propagation of partial dislocations, the generations of twins, grain boundaries, fivefold deformation twins, hexagonal close-packed (HCP) structure and phase transformation from face-centred cubic (FCC) structure to HCP structure have been triggered by pre-existing defects. It is found that surface defect intends to induce larger influence to yield strength than internal defect. Most importantly, the defect that lies on slip planes exerts larger influence than other defects. As expected, it is also found that the more or longer of the defect, the bigger influence will be induced.

Towards an orchestration theory in business transformation management (research in progress)

Business transformations are large-scale organisational change projects that, evidence suggests, are often unsuccessful. This study aims to develop a conceptual model that explains how management services that are required for a business transformation are orchestrated during such a initiative. We classify management services such as (but not limited to) change management, risk management, IT management, financial management, program management and so forth as bearing transformational and/or transactional capabilities in a transformation initiative. We then draw upon three principles of musical composition, namely melody, harmony and rhythm, and illustrate how they apply to the orchestration of management services in the management of business transformations. In order to illustrate our emerging model, we examine the case of Malaysia Airlines, who have managed to successfully turnaround the near-bankrupt organisation beyond survival. We demonstrate how the notions of melody, harmony and rhythm can be used to describe their endeavour. We conclude by discussing next steps of our research.

A conceptual model to link deep customer insights to both growth opportunities and organisational strategy in SME’s as part of a design led transformation journey

Although Design Led Innovation activities aim to raise the value of design within the business, knowledge about which tools are available to support companies and how to apply them to make the connection between design for new product development and design as a strategic driver of growth is needed. This paper presents a conceptual method to supplement existing process and tools to assist companies to grow through design. The model extends the authors’ previous work to explore how through storytelling, customer observation can be captured and translated into new meaning, then creating new design propositions shaped into product needs, which can drive internal business activities, brand and the strategic vision. The paper contributes to a gap in the theoretical frameworks and literature by highlighting the need to align and scale design processes which match the needs of SME’s as they transition along a trajectory to become design led businesses.

Can transfer of learning be enriched by valuing knowledge transformation and co-creation? Exploring new ways to improve training design

This paper argues that a possible cause of issues with management education outcomes is the fact that most training models operate from a limited ‘transfer’ metaphor. This theoretical paper contends that by reconceptualising existing models, specifically Holton’s transfer of learning model, to incorporate multiple processes and acknowledge the importance of educator- or trainer-student interaction in co-creating knowledge, there is potential to improve training design and ultimately achieve more satisfactory training outcomes.

Theoretical and numerical investigation of bending properties of Cu nanowires

Based on the AFM-bending experiments, a molecular dynamics (MD) bending simulation model is established which could accurately account for the full spectrum of the mechanical properties of NWs in a double clamped beam configuration, ranging from elasticity to plasticity and failure. It is found that, loading rate exerts significant influence to the mechanical behaviours of nanowires (NWs). Specifically, a loading rate lower than 10 m/s is found reasonable for a homogonous bending deformation. Both loading rate and potential between the tip and the NW are found to play an important role in the adhesive phenomenon. The force versus displacement (F-d) curve from MD simulation is highly consistent in shapes with that from experiments. Symmetrical F-d curves during loading and unloading processes are observed, which reveal the linear-elastic and non-elastic bending deformation of NWs. The typical bending induced tensile-compressive features are observed. Meanwhile, the simulation results are excellently fitted by the classical Euler-Bernoulli beam theory with axial effect. It is concluded that, axial tensile force becomes crucial in bending deformation when the beam size is down to nanoscale for double clamped NWs. In addition, we find shorter NWs will have an earlier yielding and a larger yielding force. Mechanical properties (Young’s modulus & yield strength) obtained from both bending and tensile deformations are found comparable with each other. Specifically, the modulus is essentially similar under these two loading methods, while the yield strength during bending is observed larger than that during tension.

Mathematical modelling of tumour-induced angiogenesis

The growth of solid tumours beyond a critical size is dependent upon angiogenesis, the formation of new blood vessels from an existing vasculature. Tumours may remain dormant at microscopic sizes for some years before switching to a mode in which growth of a supportive vasculature is initiated. The new blood vessels supply nutrients, oxygen, and access to routes by which tumour cells may travel to other sites within the host (metastasize). In recent decades an abundance of biological research has focused on tumour-induced angiogenesis in the hope that treatments targeted at the vasculature may result in a stabilisation or regression of the disease: a tantalizing prospect. The complex and fascinating process of angiogenesis has also attracted the interest of researchers in the field of mathematical biology, a discipline that is, for mathematics, relatively new. The challenge in mathematical biology is to produce a model that captures the essential elements and critical dependencies of a biological system. Such a model may ultimately be used as a predictive tool. In this thesis we examine a number of aspects of tumour-induced angiogenesis, focusing on growth of the neovasculature external to the tumour. Firstly we present a one-dimensional continuum model of tumour-induced angiogenesis in which elements of the immune system or other tumour-cytotoxins are delivered via the newly formed vessels. This model, based on observations from experiments by Judah Folkman et al., is able to show regression of the tumour for some parameter regimes. The modelling highlights a number of interesting aspects of the process that may be characterised further in the laboratory. The next model we present examines the initiation positions of blood vessel sprouts on an existing vessel, in a two-dimensional domain. This model hypothesises that a simple feedback inhibition mechanism may be used to describe the spacing of these sprouts with the inhibitor being produced by breakdown of the existing vessel's basement membrane. Finally, we have developed a stochastic model of blood vessel growth and anastomosis in three dimensions. The model has been implemented in C++, includes an openGL interface, and uses a novel algorithm for calculating proximity of the line segments representing a growing vessel. This choice of programming language and graphics interface allows for near-simultaneous calculation and visualisation of blood vessel networks using a contemporary personal computer. In addition the visualised results may be transformed interactively, and drop-down menus facilitate changes in the parameter values. Visualisation of results is of vital importance in the communication of mathematical information to a wide audience, and we aim to incorporate this philosophy in the thesis. As biological research further uncovers the intriguing processes involved in tumourinduced angiogenesis, we conclude with a comment from mathematical biologist Jim Murray, Mathematical biology is : : : the most exciting modern application of mathematics.

Binocular summation improves performance to defocus-induced blur

PURPOSE. To assess whether there are any advantages of binocular over monocular vision under blur conditions. METHODS. We measured the effect of defocus, induced by positive lenses, on the pattern reversal Visual Evoked Potential (VEP) and on visual acuity (VA). Monocular (dominant eye) and binocular VEPs were recorded from thirteen volunteers (average age: 28±5 years, average spherical equivalent: -0.25±0.73 D) for defocus up to 2.00 D using positive powered lenses. VEPs were elicited using reversing 10 arcmin checks at a rate of 4 reversals/second. The stimulus subtended a circular field of 7 degrees with 100% contrast and mean luminance 30 cd/m2. VA was measured under the same conditions using ETDRS charts. All measurements were performed at 1m viewing distance with best spectacle sphero-cylindrical correction and natural pupils. RESULTS. With binocular stimulation, amplitudes and implicit times of the P100 component of the VEPs were greater and shorter, respectively, in all cases than for monocular stimulation. Mean binocular enhancement ratio in the P100 amplitude was 2.1 in-focus, increasing linearly with defocus to be 3.1 at +2.00 D defocus. Mean peak latency was 2.9 ms shorter in-focus with binocular than for monocular stimulation, with the difference increasing with defocus to 8.8 ms at +2.00 D. As for the VEP amplitude, VA was always better with binocular than with monocular vision, with the difference being greater for higher retinal blur. CONCLUSIONS. Both subjective and electrophysiological results show that binocular vision ameliorates the effect of defocus. The increased binocular facilitation observed with retinal blur may be due to the activation of a larger population of neurons at close-to-threshold detection under binocular stimulation.

Leading the transformation of learning and praxis in science classrooms

Individual science teachers who have inspired colleagues to transform their classroom praxis have been labelled transformational leaders. As the notion of distributed leadership became more accepted in the educational literature, the focus on the individual teacher-leader shifted to the study of leadership praxis both by individuals (whoever they might be) and by collectives within schools and science classrooms. This review traces the trajectory of leadership research, in the context of learning and teaching science, from an individual focus to a dialectical relationship between individual and collective praxis. The implications of applying an individual-collective perspective to praxis for teachers, students and their designated leaders are discussed.

An estimation of crash risks using a log-linear model and the induced exposure technique

Prevention and safety promotion programmes. Traditionally, in-depth investigations of crash risks are conducted using exposure controlled study or case-control methodology. However, these studies need either observational data for control cases or exogenous exposure data like vehicle-kilometres travel, entry flow or product of conflicting flow for a particular traffic location, or a traffic site. These data are not readily available and often require extensive data collection effort on a system-wide basis. Aim: The objective of this research is to propose an alternative methodology to investigate crash risks of a road user group in different circumstances using readily available traffic police crash data. Methods: This study employs a combination of a log-linear model and the quasi-induced exposure technique to estimate crash risks of a road user group. While the log-linear model reveals the significant interactions and thus the prevalence of crashes of a road user group under various sets of traffic, environmental and roadway factors, the quasi-induced exposure technique estimates relative exposure of that road user in the same set of explanatory variables. Therefore, the combination of these two techniques provides relative measures of crash risks under various influences of roadway, environmental and traffic conditions. The proposed methodology has been illustrated using Brisbane motorcycle crash data of five years. Results: Interpretations of results on different combination of interactive factors show that the poor conspicuity of motorcycles is a predominant cause of motorcycle crashes. Inability of other drivers to correctly judge the speed and distance of an oncoming motorcyclist is also evident in right-of-way violation motorcycle crashes at intersections. Discussion and Conclusions: The combination of a log-linear model and the induced exposure technique is a promising methodology and can be applied to better estimate crash risks of other road users. This study also highlights the importance of considering interaction effects to better understand hazardous situations. A further study on the comparison between the proposed methodology and case-control method would be useful.