Fused deposition modeling with polypropylene

This paper addresses the potential of polypropylene (PP) as a candidate for fused deposition modeling (FDM)-based 3D printing technique. The entire filament production chain is evaluated, starting with the PP pellets, filament production by extrusion and test samples printing. This strategy enables a true comparison between parts printed with parts manufactured by compression molding, using the same grade of raw material. Printed samples were mechanically characterized and the influence of filament orientation, layer thickness, infill degree and material was assessed. Regarding the latter, two grades of PP were evaluated: a glass-fiber reinforced and a neat, non-reinforced, one. The results showed the potential of the FDM to compete with conventional techniques, especially for the production of small series of parts/components; also, it was showed that this technique allows the production of parts with adequate mechanical performance and, therefore, does not need to be restricted to the production of mockups and prototypes.

[Editorial] Current challenges in modeling cellular metabolism

The authors would like to thank the financial support from the NovoNordiskFoundation.

Modeling separator membranes physical characteristics for optimized lithium ion battery performance

The effect of varying separator membrane physical parameters such as degree of porosity, tortuosity and thickness, on battery delivered capacity was studied in order to optimize performance of lithium-ion batteries. This was achieved by a theoretical mathematical model relating the Bruggeman coefficient with the degree of porosity and tortuosity. The inclusion of the separator membrane in the simulation model of the battery system does not affect the delivered capacity of the battery. The ionic conductivity of the separator and consequently the delivered capacity values obtained at different discharge rates depends on the value of the Bruggeman coefficient, which is related with the degree of porosity and tortuosity of the membrane. Independently of scan rate, the optimal value of the degree of porosity is above 50% and the separator thickness should range between 1 μm at 32 μm for improved battery performance.

Project scheduling and cost minimization with multiple availability constrained resources under stochastic conditions

The authors propose a mathematical model to minimize the project total cost where there are multiple resources constrained by maximum availability. They assume the resources as renewable and the activities can use any subset of resources requiring any quantity from a limited real interval. The stochastic nature is inferred by means of a stochastic work content defined per resource within an activity and following a known distribution and the total cost is the sum of the resource allocation cost with the tardiness cost or earliness bonus in case the project finishes after or before the due date, respectively. The model was computationally implemented relying upon an interchange of two global optimization metaheuristics – the electromagnetism-like mechanism and the evolutionary strategies. Two experiments were conducted testing the implementation to projects with single and multiple resources, and with or without maximum availability constraints. The set of collected results shows good behavior in general and provide a tool to further assist project manager decision making in the planning phase.

Population Dynamics Modeling of Arapaima gigas

Pirarucu (Arapaima gigas) has been of the most important natural fishing resources of the Amazon region. Due to its economic importance, and the necessity to preserve the species hand, field research concerning the habits and behavior of the pirarucu has been increasing for the last 20 years. The aim of this paper is to present a mathematical model for the pirarucu population dynamics considering the species peculiarities, particularly the male parental care over the offspring. The solution of the dynamical systems indicates three possible equilibrium points for the population. The first corresponds to extinction; the third corresponds to a stable population close to the environmental carrying capacity. The second corresponds to an unstable equilibrium located between extinction and full use of the carrying capacity. It is shown that lack of males’ parental care closes the gap between the point corresponding to the unstable equilibrium and the point of stable non-trivial equilibrium. If guarding failure reaches a critical point the two points coincide and the population tends irreversibly to extinction. If some event tends to destabilize the population equilibrium, as for instance inadequate parental care, the model responds in such a way as to restore the trajectory towards the stable equilibrium point avoiding the route to extinction. The parameters introduced to solve the system of equations are partially derived from limited but reliable field data collected at the Mamirauá Sustainable Development Reserve (MSDR) in the Brazilian Amazonian Region.

Bootstrap performance profiles in stochastic algorithms assessment

Optimization with stochastic algorithms has become a relevant research field. Due to its stochastic nature, its assessment is not straightforward and involves integrating accuracy and precision. Performance profiles for the mean do not show the trade-off between accuracy and precision, and parametric stochastic profiles require strong distributional assumptions and are limited to the mean performance for a large number of runs. In this work, bootstrap performance profiles are used to compare stochastic algorithms for different statistics. This technique allows the estimation of the sampling distribution of almost any statistic even with small samples. Multiple comparison profiles are presented for more than two algorithms. The advantages and drawbacks of each assessment methodology are discussed.

Numerical modeling and assessment of the thermal environment in an industrial premise of automotive components

Dissertação de mestrado em Engenharia Industrial

Poker learner: modelação de jogadores através de data mining

Dissertação de mestrado integrado em Engenharia e Gestão de Sistemas de Informação

Influence of the hip joint modeling approaches on the kinematics of human gait

The influence of the hip joint formulation on the kinematic response of the model of human gait is investigated throughout this work. To accomplish this goal, the fundamental issues of the modeling process of a planar hip joint under the framework of multibody systems are revisited. In particular, the formulations for the ideal, dry, and lubricated revolute joints are described and utilized for the interaction of femur head inside acetabulum or the hip bone. In this process, the main kinematic and dynamic aspects of hip joints are analyzed. In a simple manner, the forces that are generated during human gait, for both dry and lubricated hip joint models, are computed in terms of the system’s state variables and subsequently introduced into the dynamics equations of motion of the multibody system as external generalized forces. Moreover, a human multibody model is considered, which incorporates the different approaches for the hip articulation, namely ideal joint, dry, and lubricated models. Finally, several computational simulations based on different approaches are performed, and the main results presented and compared to identify differences among the methodologies and procedures adopted in this work. The input conditions to the models correspond to the experimental data capture from an adult male during normal gait. In general, the obtained results in terms of positions do not differ significantly when the different hip joint models are considered. In sharp contrast, the velocity and acceleration plotted vary significantly. The effect of the hip joint modeling approach is clearly measurable and visible in terms of peaks and oscillations of the velocities and accelerations. In general, with the dry hip model, intra-joint force peaks can be observed, which can be associated with the multiple impacts between the femur head and the cup. In turn, when the lubricant is present, the system’s response tends to be smoother due to the damping effects of the synovial fluid.

A integração de técnicas BIM (Building Information Modeling) no projeto e na construção de estruturas de madeira

Dissertação de mestrado integrado em Engenharia Civil

A integração do Building Information Modeling (BIM) num projeto de reabilitação

Dissertação de mestrado integrado em Engenharia Civil

Current Challenges in Modeling Cellular Metabolism

Mathematical and computational models play an essential role in understanding the cellular metabolism. They are used as platforms to integrate current knowledge on a biological system and to systematically test and predict the effect of manipulations to such systems. The recent advances in genome sequencing techniques have facilitated the reconstruction of genome-scale metabolic networks for a wide variety of organisms from microbes to human cells. These models have been successfully used in multiple biotechnological applications. Despite these advancements, modeling cellular metabolism still presents many challenges. The aim of this Research Topic is not only to expose and consolidate the state-of-the-art in metabolic modeling approaches, but also to push this frontier beyond the current edge through the introduction of innovative solutions. The articles presented in this e-book address some of the main challenges in the field, including the integration of different modeling formalisms, the integration of heterogeneous data sources into metabolic models, explicit representation of other biological processes during phenotype simulation, and standardization efforts in the representation of metabolic models and simulation results.

A UML-based approach for modeling industrial control applications

The main purpose of the poster is to present how the Unified Modeling Language (UML) can be used for diagnosing and optimizing real industrial production systems. By using a car radios production line as a case study, the poster shows the modeling process that can be followed during the analysis phase of complex control applications. In order to guarantee the continuity mapping of the models, the authors propose some guidelines to transform the use cases diagrams into a single object diagram, which is the main diagram for the next phases of the development.

Vascular disease modeling using induced pluripotent stem cells: Focus in Hutchinson-Gilford Progeria Syndrome

Transparency document related to this article can be found online at http://dx.doi.org/10.1016/j.bbrc.2015.10.014

Factores Críticos del Desarrollo Local y Regional Integrado zona serrana y Norte de la Provincia de Córdoba-. Validación causal estadística de Modelos de Ecuaciones Estructurales. Identificación de problemas normativos de las OSC.Critical Factors of Local and Regional Development in north of the Province of Córdoba. Causal validation with Structural Equation Modeling. Legal regulations of civil society.

En la investigación anterior -en la zona pampeana de la Provincia de Córdoba- se demostró teórica y empíricamente, que el desarrollo de la Sociedad Civil muchas veces libradas a su suerte y con limitaciones legales apoyan decididamente el desarrollo local, sin embargo han logrado solo parcialmente sus objetivos, por lo que es necesario comenzar un camino de fortalecimiento en los nuevos roles que deben asumir. Los gobiernos locales, a la vez, intentan trabajosamente con contados éxitos detener el procesos de descapitalización social -financiera y humana- de sus comunidades locales y regionales, peregrinando con escaso éxito a los centros concentrados del poder político y económico, para procurar los recursos financieros y humanos necesarios que no alcanzan a reponer los que se fugan desde hace décadas de sus localidades. Las empresas, con ciclos recurrentes de crecimiento y decrecimiento vinculados a los mercados en que colocan sus productos, también se debaten en la búsqueda de los escasos recursos, financieros y humanos, que les permitan consolidar un desarrollo a mediano y largo plazo. El desarrollo alcanzado en Sistemas de información, instrumentos de relevamiento, análisis y elaboración de propuestas para el Desarrollo Local, nos permite avanzar en: 1. La confirmación empírica de las hipótesis iniciales - factores exógenos y endógenos - en la zona Norte y Serrana de la provincia 2. La validación científica -mediante el Análisis de ecuaciones estructurales. de tales supuestos, para el conjunto de las poblaciones analizadas en ambas etapas. 3. La identificación de los problemas normativos que afectan el desarrollo de las Organizaciones de la Sociedad Civil (OSC). METODOLOGÍA Respecto la validación empírica en la zona norte y serrana 1. Selección de las 4 localidades a relevar de acuerdo a las categorías definidas 2. Elaboración de acuerdos con autoridades e instituciones locales. 3. Relevamiento cualitativo con líderes locales y fuentes de datos secundarias. 4. Adaptación de instrumentos de relevamiento a las realidades locales y estudios previos 5. Relevamiento cuantitativo de campo, capacitación de encuestadores y supervisores. 6. Procesamiento y elaboración de informes finales locales. Respecto de la construcción de modelos de desarrollo 1. Desarrollar las dimensiones especificas y las variables (items) de cada factor crítico. 2. Revisar el instrumento con expertos de cada una de las dimensiones. 3. Validar a nivel exploratorio por medio de un Análisis de Componentes Principales 4. Someter a los expertos la evaluación de una serie de localidades que representan cada uno. Respecto de la identificación de las normas legales que afectan a la Sociedad Civil 1.Relevamiento documental de normas 2. Relevamiento con líderes de instituciones de la Sociedad Civil 3. Análisis de las normas vigentes 4. Elaboración de Informes Finales y Transferencia a líderes e instituciones