Estrutura de sistemas de três corpos fracamente ligados em duas dimensões

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Structural evolution of Eu-doped hydroxyapatite nanorods monitored by photoluminescence emission

This paper reports the synthesis of Eu-doped hydroxyapatite (HA:Eu) resulting in particles with nanorod diameters from 9 to 26 nm using the microwave hydrothermal method (HTMW). Eu3+ ions were used as a marker in the HA network by basic hydrolysis followed by the HTMW treatment. The crystalline HA:Eu nanorod nature in a short-range order was detected by photoluminescence (PL) measurements from Eu3+ emission into the HA matrix. Thus, was possible to verify that HA crystallization is favored in a short structural order when the HTMW treatment time was increased from 0 to 40 min and that the Eu3+ substitution in the HA lattice is site-selective. (C) 2012 Elsevier B.V. All rights reserved.

PbO-GeO2 rare earth doped glasses with silver nanoparticles as materials for IR laser triggers

We have shown the possibility of operation by the piezooptical response of PbO-GeO2 glasses doped with rare earth ions and silver nanoparticles by illumination of double frequency CO2 nanosecond laser. Substantial influence of thermoannealing on the output photoinduced elastooptical susceptibilities was established. The effect is very sensitive to temperature and to the corresponding tensor components. The effect of thermoannealing leads to enhanced long-range ordering with the occurrence of corresponding trapping levels within the forbidden gaps. The discovered effects may be used for creation of low-temperature IR laser triggers.

Imperceptible electrical noise attenuates isometric plantar flexion force fluctuations with correlated reductions in postural sway

Optimal levels of noise stimulation have been shown to enhance the detection and transmission of neural signals thereby improving the performance of sensory and motor systems. The first series of experiments in the present study aimed to investigate whether subsensory electrical noise stimulation applied over the triceps surae (TS) in seated subjects decreases torque variability during a force-matching task of isometric plantar flexion and whether the same electrical noise stimulation decreases postural sway during quiet stance. Correlation tests were applied to investigate whether the noise-induced postural sway decrease is linearly predicted by the noise-induced torque variability decrease. A second series of experiments was conducted to investigate whether there are differences in torque variability between conditions in which the subsensory electrical noise is applied only to the TS, only to the tibialis anterior (TA) and to both TS and TA, during the force-matching task with seated subjects. Noise stimulation applied over the TS muscles caused a significant reduction in force variability during the maintained isometric force paradigm and also decreased postural oscillations during quiet stance. Moreover, there was a significant correlation between the reduction in force fluctuation and the decrease in postural sway with the electrical noise stimulation. This last result indicates that changes in plantar flexion force variability in response to a given subsensory random stimulation of the TS may provide an estimate of the variations in postural sway caused by the same subsensory stimulation of the TS. We suggest that the decreases in force variability and postural sway found here are due to stochastic resonance that causes an improved transmission of proprioceptive information. In the second series of experiments, the reduction in force variability found when noise was applied to the TA muscle alone did not reach statistical significance, suggesting that TS proprioception gives a better feedback to reduce force fluctuation in isometric plantar flexion conditions.

Tailored SERS substrates obtained with cathodic arc plasma ion implantation of gold nanoparticles into a polymer matrix

This manuscript reports on the fabrication of plasmonic substrates using cathodic arc plasma ion implantation, in addition to their performance as SERS substrates. The technique allows for the incorporation of a wide layer of metallic nanoparticles into a polymer matrix, such as PMMA. The ability to pattern different structures using the PMMA matrix is one of the main advantages of the fabrication method. This opens up new possibilities for obtaining tailored substrates with enhanced performance for SERS and other surface-enhanced spectroscopies, as well as for exploring the basic physics of patterned metal nanostructures. The architecture of the SERS-active substrate was varied using three adsorption strategies for incorporating a laser dye (rhodamine): alongside the nanoparticles into the polymer matrix, during the polymer cure and within nanoholes lithographed on the polymer. As a proof-of-concept, we obtained the SERS spectra of rhodamine for the three types of substrates. The hypothesis of incorporation of rhodamine molecules into the polymer matrix during the cathodic arc plasma ion implantation was supported by FDTD (Finite-Difference Time-Domain) simulations. In the case of arrays of nanoholes, rhodamine molecules could be adsorbed directly on the gold surface, then yielding a well-resolved SERS spectrum for a small amount of analyte owing to the short-range interactions and the large longitudinal field component inside the nanoholes. The results shown here demonstrate that the approach based on ion implantation can be adapted to produce reproducible tailored substrates for SERS and other surface-enhanced spectroscopies.

Structure and Ionic Conductivity in the Mixed-Network Former Chalcogenide Glass System [Na2S](2/3)[(B2S3)(x)(P2S5)(1-x)](1/3)

Glasses in the system [Na2S](2/3)[(B2S3)(x)(P2S5)(1-x)](1/3) (0.0 <= x <= 1.0) were prepared by the melt quenching technique, and their properties were characterized by thermal analysis and impedance spectroscopy. Their atomic-level structures were comprehensively characterized by Raman spectroscopy and B-11, P-31, and Na-23 high resolution solid state magic-angle spinning (MAS) NMR techniques. P-31 MAS NMR peak assignments were made by the presence or absence of homonuclear indirect P-31-P-31 spin-spin interactions as detected using homonuclear J-resolved and refocused INADEQUATE techniques. The extent of B-S-P connectivity in the glassy network was quantified by P-31{B-11} and B-11{P-31} rotational echo double resonance spectroscopy. The results clearly illustrate that the network modifier alkali sulfide, Na2S, is not proportionally shared between the two network former components, B and P. Rather, the thiophosphate (P) component tends to attract a larger concentration of network modifier species than predicted by the bulk composition, and this results in the conversion of P2S74-, pyrothiophosphate, Na/P = 2:1, units into PS43-, orthothiophosphate, Na/P = 3:1, groups. Charge balance is maintained by increasing the net degree of polymerization of the thioborate (B) units through the formation of covalent bridging sulfur (BS) units, B S B. Detailed inspection of the B-11 MAS NMR spectra reveals that multiple thioborate units are formed, ranging from neutral BS3/2 groups all the way to the fully depolymerized orthothioborate (BS33-) species. On the basis of these results, a comprehensive and quantitative structural model is developed for these glasses, on the basis of which the compositional trends in the glass transition temperatures (T-g) and ionic conductivities can be rationalized. Up to x = 0.4, the dominant process can be described in a simplified way by the net reaction equation P-1 + B-1 reversible arrow P-0 + B-4, where the superscripts denote the number of BS atoms for the respective network former species. Above x = 0.4, all of the thiophosphate units are of the P-0 type and both pyro-(B-1) and orthothioborate (B-0) species make increasing contributions to the network structure with increasing x. In sharp contrast to the situation in sodium borophosphate glasses, four-coordinated thioborate species are generally less abundant and heteroatomic B-S-P linkages appear to not exist. On the basis of this structural information, compositional trends in the ionic conductivities are discussed in relation to the nature of the charge-compensating anionic species and the spatial distribution of the charge carriers.

Structural properties and energetics of diffuse Rb-87 clusters in three-dimension

A correlated two-body basis function is used to describe the three-dimensional bosonic clusters interacting via two-body van der Waals potential. We calculate the ground state and the zero orbital angular momentum excited states for Rb-N clusters with up to N = 40. We solve the many-particle Schrodinger equation by potential harmonics expansion method, which keeps all possible two-body correlations in the calculation and determines the lowest effective many-body potential. We study energetics and structural properties for such diffuse clusters both at dimer and tuned scattering length. The motivation of the present study is to investigate the possibility of formation of N-body clusters interacting through the van der Waals interaction. We also compare the system with the well studied He, Ne, and Ar clusters. We also calculate correlation properties and observe the generalised Tjon line for large cluster. We test the validity of the shape-independent potential in the calculation of the ground state energy of such diffuse cluster. These are the first such calculations reported for Rb clusters. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4730972]

The Role of Molecular Conformation and Polarizable Embedding for One- and Two-Photon Absorption of Disperse Orange 3 in Solution

Solvent effects on the one- and two-photon absorption (IPA and 2PA) of disperse orange 3 (DO3) in dimethyl sulfoxide (DMSO) are studied using a discrete polarizable embedding (PE) response theory. The scheme comprises a quantum region containing the chromophore and an atomically granulated classical region for the solvent accounting for full interactions within and between the two regions. Either classical molecular dynamics (MD) or hybrid Car-Parrinello (CP) quantum/classical (QM/MM) molecular dynamics simulations are employed to describe the solvation of DO3 in DMSO, allowing for an analysis of the effect of the intermolecular short-range repulsion, long-range attraction, and electrostatic interactions on the conformational changes of the chromophore and also the effect of the solute-solvent polarization. PE linear response calculations are performed to verify the character, solvatochromic shift, and overlap of the two lowest energy transitions responsible for the linear absorption spectrum of DO3 in DMSO in the visible spectral region. Results of the PE linear and quadratic response calculations, performed using uncorrelated solute-solvent configurations sampled from either the classical or hybrid CP QM/MM MD simulations, are used to estimate the width of the line shape function of the two electronic lowest energy excited states, which allow a prediction of the 2PA cross-sections without the use of empirical parameters. Appropriate exchange-correlation functionals have been employed in order to describe the charge-transfer process following the electronic transitions of the chromophore in solution.

Influence of the network modifier on the characteristics of MSnO3 (M=Sr and Ca) thin films synthesized by chemical solution deposition

CaSnO3 and SrSnO3 alkaline earth stannate thin films were prepared by chemical solution deposition using the polymeric precursor method on various single crystal substrates (R- and C-sapphire and 100-SrTiO3) at different temperatures. The films were characterized by X-ray diffraction (θ-2θ, ω- and φ-scans), field emission scanning electron microscopy, atomic force microscopy, micro-Raman spectroscopy and photoluminescence. Epitaxial SrSnO3 and CaSnO3 thin films were obtained on SrTiO3 with a high crystalline quality. The long-range symmetry promoted a short-range disorder which led to photoluminescence in the epitaxial films. In contrast, the films deposited on sapphire exhibited a random polycrystalline growth with no meaningful emission regardless of the substrate orientation. The network modifier (Ca or Sr) and the substrate (sapphire or SrTiO3) influenced the crystallization process and/or the microstructure. Higher is the tilts of the SnO6 octahedra, as in CaSnO3, higher is the crystallization temperature, which changed also the nucleation/grain growth process.

Dynamical aspects of atmospheric data assimilation in the tropics

A faithful depiction of the tropical atmosphere requires three-dimensional sets of observations. Despite the increasing amount of observations presently available, these will hardly ever encompass the entire atmosphere and, in addition, observations have errors. Additional (background) information will always be required to complete the picture. Valuable added information comes from the physical laws governing the flow, usually mediated via a numerical weather prediction (NWP) model. These models are, however, never going to be error-free, why a reliable estimate of their errors poses a real challenge since the whole truth will never be within our grasp. The present thesis addresses the question of improving the analysis procedures for NWP in the tropics. Improvements are sought by addressing the following issues: - the efficiency of the internal model adjustment, - the potential of the reliable background-error information, as compared to observations, - the impact of a new, space-borne line-of-sight wind measurements, and - the usefulness of multivariate relationships for data assimilation in the tropics. Most NWP assimilation schemes are effectively univariate near the equator. In this thesis, a multivariate formulation of the variational data assimilation in the tropics has been developed. The proposed background-error model supports the mass-wind coupling based on convectively-coupled equatorial waves. The resulting assimilation model produces balanced analysis increments and hereby increases the efficiency of all types of observations. Idealized adjustment and multivariate analysis experiments highlight the importance of direct wind measurements in the tropics. In particular, the presented results confirm the superiority of wind observations compared to mass data, in spite of the exact multivariate relationships available from the background information. The internal model adjustment is also more efficient for wind observations than for mass data. In accordance with these findings, new satellite wind observations are expected to contribute towards the improvement of NWP and climate modeling in the tropics. Although incomplete, the new wind-field information has the potential to reduce uncertainties in the tropical dynamical fields, if used together with the existing satellite mass-field measurements. The results obtained by applying the new background-error representation to the tropical short-range forecast errors of a state-of-art NWP model suggest that achieving useful tropical multivariate relationships may be feasible within an operational NWP environment.

Transcriptional regulation of human mu-opioid receptor gene: functional characterization of activating and inhibitory transcription factors

The organization of the nervous and immune systems is characterized by obvious differences and striking parallels. Both systems need to relay information across very short and very long distances. The nervous system communicates over both long and short ranges primarily by means of more or less hardwired intercellular connections, consisting of axons, dendrites, and synapses. Longrange communication in the immune system occurs mainly via the ordered and guided migration of immune cells and systemically acting soluble factors such as antibodies, cytokines, and chemokines. Its short-range communication either is mediated by locally acting soluble factors or transpires during direct cell–cell contact across specialized areas called “immunological synapses” (Kirschensteiner et al., 2003). These parallels in intercellular communication are complemented by a complex array of factors that induce cell growth and differentiation: these factors in the immune system are called cytokines; in the nervous system, they are called neurotrophic factors. Neither the cytokines nor the neurotrophic factors appear to be completely exclusive to either system (Neumann et al., 2002). In particular, mounting evidence indicates that some of the most potent members of the neurotrophin family, for example, nerve growth factor (NGF) and brainderived neurotrophic factor (BDNF), act on or are produced by immune cells (Kerschensteiner et al., 1999) There are, however, other neurotrophic factors, for example the insulin-like growth factor-1 (IGF-1), that can behave similarly (Kermer et al., 2000). These factors may allow the two systems to “cross-talk” and eventually may provide a molecular explanation for the reports that inflammation after central nervous system (CNS) injury has beneficial effects (Moalem et al., 1999). In order to shed some more light on such a cross-talk, therefore, transcription factors modulating mu-opioid receptor (MOPr) expression in neurons and immune cells are here investigated. More precisely, I focused my attention on IGF-I modulation of MOPr in neurons and T-cell receptor induction of MOPr expression in T-lymphocytes. Three different opioid receptors [mu (MOPr), delta (DOPr), and kappa (KOPr)] belonging to the G-protein coupled receptor super-family have been cloned. They are activated by structurallyrelated exogenous opioids or endogenous opioid peptides, and contribute to the regulation of several functions including pain transmission, respiration, cardiac and gastrointestinal functions, and immune response (Zollner and Stein 2007). MOPr is expressed mainly in the central nervous system where it regulates morphine-induced analgesia, tolerance and dependence (Mayer and Hollt 2006). Recently, induction of MOPr expression in different immune cells induced by cytokines has been reported (Kraus et al., 2001; Kraus et al., 2003). The human mu-opioid receptor gene (OPRM1) promoter is of the TATA-less type and has clusters of potential binding sites for different transcription factors (Law et al. 2004). Several studies, primarily focused on the upstream region of the OPRM1 promoter, have investigated transcriptional regulation of MOPr expression. Presently, however, it is still not completely clear how positive and negative transcription regulators cooperatively coordinate cellor tissue-specific transcription of the OPRM1 gene, and how specific growth factors influence its expression. IGF-I and its receptors are widely distributed throughout the nervous system during development, and their involvement in neurogenesis has been extensively investigated (Arsenijevic et al. 1998; van Golen and Feldman 2000). As previously mentioned, such neurotrophic factors can be also produced and/or act on immune cells (Kerschenseteiner et al., 2003). Most of the physiologic effects of IGF-I are mediated by the type I IGF surface receptor which, after ligand binding-induced autophosphorylation, associates with specific adaptor proteins and activates different second messengers (Bondy and Cheng 2004). These include: phosphatidylinositol 3-kinase, mitogen-activated protein kinase (Vincent and Feldman 2002; Di Toro et al. 2005) and members of the Janus kinase (JAK)/STAT3 signalling pathway (Zong et al. 2000; Yadav et al. 2005). REST plays a complex role in neuronal cells by differentially repressing target gene expression (Lunyak et al. 2004; Coulson 2005; Ballas and Mandel 2005). REST expression decreases during neurogenesis, but has been detected in the adult rat brain (Palm et al. 1998) and is up-regulated in response to global ischemia (Calderone et al. 2003) and induction of epilepsy (Spencer et al. 2006). Thus, the REST concentration seems to influence its function and the expression of neuronal genes, and may have different effects in embryonic and differentiated neurons (Su et al. 2004; Sun et al. 2005). In a previous study, REST was elevated during the early stages of neural induction by IGF-I in neuroblastoma cells. REST may contribute to the down-regulation of genes not yet required by the differentiation program, but its expression decreases after five days of treatment to allow for the acquisition of neural phenotypes. Di Toro et al. proposed a model in which the extent of neurite outgrowth in differentiating neuroblastoma cells was affected by the disappearance of REST (Di Toro et al. 2005). The human mu-opioid receptor gene (OPRM1) promoter contains a DNA sequence binding the repressor element 1 silencing transcription factor (REST) that is implicated in transcriptional repression. Therefore, in the fist part of this thesis, I investigated whether insulin-like growth factor I (IGF-I), which affects various aspects of neuronal induction and maturation, regulates OPRM1 transcription in neuronal cells in the context of the potential influence of REST. A series of OPRM1-luciferase promoter/reporter constructs were transfected into two neuronal cell models, neuroblastoma-derived SH-SY5Y cells and PC12 cells. In the former, endogenous levels of human mu-opioid receptor (hMOPr) mRNA were evaluated by real-time PCR. IGF-I upregulated OPRM1 transcription in: PC12 cells lacking REST, in SH-SY5Y cells transfected with constructs deficient in the REST DNA binding element, or when REST was down-regulated in retinoic acid-differentiated cells. IGF-I activates the signal transducer and activator of transcription-3 (STAT3) signaling pathway and this transcription factor, binding to the STAT1/3 DNA element located in the promoter, increases OPRM1 transcription. T-cell receptor (TCR) recognizes peptide antigens displayed in the context of the major histocompatibility complex (MHC) and gives rise to a potent as well as branched intracellular signalling that convert naïve T-cells in mature effectors, thus significantly contributing to the genesis of a specific immune response. In the second part of my work I exposed wild type Jurkat CD4+ T-cells to a mixture of CD3 and CD28 antigens in order to fully activate TCR and study whether its signalling influence OPRM1 expression. Results were that TCR engagement determined a significant induction of OPRM1 expression through the activation of transcription factors AP-1, NF-kB and NFAT. Eventually, I investigated MOPr turnover once it has been expressed on T-cells outer membrane. It turned out that DAMGO induced MOPr internalisation and recycling, whereas morphine did not. Overall, from the data collected in this thesis we can conclude that that a reduction in REST is a critical switch enabling IGF-I to up-regulate human MOPr, helping these findings clarify how human MOPr expression is regulated in neuronal cells, and that TCR engagement up-regulates OPRM1 transcription in T-cells. My results that neurotrophic factors a and TCR engagement, as well as it is reported for cytokines, seem to up-regulate OPRM1 in both neurons and immune cells suggest an important role for MOPr as a molecular bridge between neurons and immune cells; therefore, MOPr could play a key role in the cross-talk between immune system and nervous system and in particular in the balance between pro-inflammatory and pro-nociceptive stimuli and analgesic and neuroprotective effects.

Sphärische Bürsten in polymeren Schmelzen

Colloidal nanoparticles are additives to improve or modify several properties of thermoplastic or elastic polymers. Usually colloid-polymer mixtures show phase separation due to the depletion effect. The strategy to overcome this depletion demixing was to prepare surface-modified colloidal particles, which can be blended with linear polymer chains homogeneous. A successful synthesis strategy for the preparation of hairy nanospheres was developed by grafting polystyrene macromonomer chains onto polyorganosiloxane microgels. The number of hairs per particle with a core radius of approximately 10nm exceeded 150 hairs in all cases. The molecular weight of the hairs variied between 4000-18000g/mol.The compatibility of these hairy spheres mixed with linear polymer chains was investigated by AFM, TEM and SAXS. Homogeneous mixtures were found if the molecular weight of the polymer hairs on the particle surface is at least as large as the molecular weight of the matrix chains. If the chains are much shorter than the hairs, the colloidal hair corona is strongly swollen by the matrix polymer, leading to a long-range soft interparticle repulsion ('wet brush'). If hairs and chains are comparable in length, the corona shows much less volume swelling, leading to a short-range repulsive potential similar to hard sphere systems ('dry brush'). Polymerketten und Kolloidpartikel entmischen aufgrund von Depletion-Wechselwirkungen. Diese entropisch bedingte Entmischung konnte durch das Ankoppeln von Polymerhaaren verschiedenen Molekulargewichts auf die Kugeloberflächen der Kolloide bis zu hohen Konzentrationen vermieden werden. Zur Darstellung sphärischer Bürsten und haariger Tracerpartikel wurde eine neue Synthesestrategie ausgearbeitet und erfolgreich umgesetzt.Das Kompatibilitätsverhalten dieser sphärischen Bürsten in der Schmelze von Polymerketten als Matrix wurde mittels Elektronenmikroskopie und Kleinwinkelröntgenstreuung untersucht. Die Mischungen setzten sich aus sphärischen Bürsten und Matrixketten mit unterschiedlichen Molekulargewichten zusammen.Es zeigte sich, daß die Mischbarkeit entschieden durch das Verhältnis von Haarlänge zu Länge der Matrixketten beeinflußt wird.Aus den Untersuchungen des Relaxationsverhaltens mittels Rheologie und SAXS ergibt sich, daß das Konzept der 'dry brush'- und 'wet brush'-Systeme auf diese Mischungen übertragbar ist. Die Volumenquellung der Haarcorona durch die Matrixketten ist, wie die Experimente gezeigt haben, bereits im Fall von Polymeren mit relativ niedrigen Molekulargewichten zu beobachten. Sie ist umso stärker ausgeprägt, je größer das Längenverhältnis zwischen Polymerhaaren und Matrixketten ist. Die Quellung bedeutet eine Vergrößerung des effektiven Radius der Partikel und entspricht somit einer Erhöhung des effektiven Volumenbruchs. Dies führt zur Ausbildung einer höheren Ordnung und zu einem Einfrieren der Relaxation dieser strukturellen Ordnung führt.

Impatto della propagazione elettromagnetica sulle prestazioni delle reti M3N

Con il termine Smart Grid si intende una rete urbana capillare che trasporta energia, informazione e controllo, composta da dispositivi e sistemi altamente distribuiti e cooperanti. Essa deve essere in grado di orchestrare in modo intelligente le azioni di tutti gli utenti e dispositivi connessi al fine di distribuire energia in modo sicuro, efficiente e sostenibile. Questo connubio fra ICT ed Energia viene comunemente identificato anche con il termine Smart Metering, o Internet of Energy. La crescente domanda di energia e l’assoluta necessità di ridurre gli impatti ambientali (pacchetto clima energia 20-20-20 [9]), ha creato una convergenza di interessi scientifici, industriali e politici sul tema di come le tecnologie ICT possano abilitare un processo di trasformazione strutturale di ogni fase del ciclo energetico: dalla generazione fino all’accumulo, al trasporto, alla distribuzione, alla vendita e, non ultimo, il consumo intelligente di energia. Tutti i dispositivi connessi, diventeranno parte attiva di un ciclo di controllo esteso alle grandi centrali di generazione così come ai comportamenti dei singoli utenti, agli elettrodomestici di casa, alle auto elettriche e ai sistemi di micro-generazione diffusa. La Smart Grid dovrà quindi appoggiarsi su una rete capillare di comunicazione che fornisca non solo la connettività fra i dispositivi, ma anche l’abilitazione di nuovi servizi energetici a valore aggiunto. In questo scenario, la strategia di comunicazione sviluppata per lo Smart Metering dell’energia elettrica, può essere estesa anche a tutte le applicazioni di telerilevamento e gestione, come nuovi contatori dell’acqua e del gas intelligenti, gestione dei rifiuti, monitoraggio dell’inquinamento dell’aria, monitoraggio del rumore acustico stradale, controllo continuo del sistema di illuminazione pubblico, sistemi di gestione dei parcheggi cittadini, monitoraggio del servizio di noleggio delle biciclette, ecc. Tutto ciò si prevede possa contribuire alla progettazione di un unico sistema connesso, dove differenti dispositivi eterogenei saranno collegati per mettere a disposizione un’adeguata struttura a basso costo e bassa potenza, chiamata Metropolitan Mesh Machine Network (M3N) o ancora meglio Smart City. Le Smart Cities dovranno a loro volta diventare reti attive, in grado di reagire agli eventi esterni e perseguire obiettivi di efficienza in modo autonomo e in tempo reale. Anche per esse è richiesta l’introduzione di smart meter, connessi ad una rete di comunicazione broadband e in grado di gestire un flusso di monitoraggio e controllo bi-direzionale esteso a tutti gli apparati connessi alla rete elettrica (ma anche del gas, acqua, ecc). La M3N, è un’estensione delle wireless mesh network (WMN). Esse rappresentano una tecnologia fortemente attesa che giocherà un ruolo molto importante nelle futura generazione di reti wireless. Una WMN è una rete di telecomunicazione basata su nodi radio in cui ci sono minimo due percorsi che mettono in comunicazione due nodi. E’ un tipo di rete robusta e che offre ridondanza. Quando un nodo non è più attivo, tutti i rimanenti possono ancora comunicare tra di loro, direttamente o passando da uno o più nodi intermedi. Le WMN rappresentano una tipologia di rete fondamentale nel continuo sviluppo delle reti radio che denota la divergenza dalle tradizionali reti wireless basate su un sistema centralizzato come le reti cellulari e le WLAN (Wireless Local Area Network). Analogamente a quanto successo per le reti di telecomunicazione fisse, in cui si è passati, dalla fine degli anni ’60 ai primi anni ’70, ad introdurre schemi di rete distribuite che si sono evolute e man mano preso campo come Internet, le M3N promettono di essere il futuro delle reti wireless “smart”. Il primo vantaggio che una WMN presenta è inerente alla tolleranza alla caduta di nodi della rete stessa. Diversamente da quanto accade per una rete cellulare, in cui la caduta di una Base Station significa la perdita di servizio per una vasta area geografica, le WMN sono provviste di un’alta tolleranza alle cadute, anche quando i nodi a cadere sono più di uno. L'obbiettivo di questa tesi è quello di valutare le prestazioni, in termini di connettività e throughput, di una M3N al variare di alcuni parametri, quali l’architettura di rete, le tecnologie utilizzabili (quindi al variare della potenza, frequenza, Building Penetration Loss…ecc) e per diverse condizioni di connettività (cioè per diversi casi di propagazione e densità abitativa). Attraverso l’uso di Matlab, è stato quindi progettato e sviluppato un simulatore, che riproduce le caratteristiche di una generica M3N e funge da strumento di valutazione delle performance della stessa. Il lavoro è stato svolto presso i laboratori del DEIS di Villa Grifone in collaborazione con la FUB (Fondazione Ugo Bordoni).

Physikalische Eigenschaften kolloidaler Festkörper

In dieser Arbeit wird das Phasenverhalten fluid-kristallin und kristallin-amorph, die elastischen Eigenschaften, das Nukleationsverhalten und das diffusive Verhalten ladungsstabilisierter Kolloide aus sphärischen Polystyrol- und Polytetrafluorethylenpartikeln in wässerigen Dispersionsmitteln bei sehr geringem Fremdionengehalt systematisch untersucht. Die dazugehörigen Messungen werden an einer neuartigen selbstkonstruierten Kombinationslichtstreuapparatur durchgeführt, die die Meßmethoden der dynamischen Lichtstreuung, statischen Lichtstreuung und Torsionsresonanzspektroskopie in sich vereint. Die drei Meßmethoden sind optimal auf die Untersuchung kolloidaler Festkörper abgestimmt. Das elastische Verhalten der Festkörper kann sehr gut durch die Elastizitätstheorie atomarer Kristallsysteme beschrieben werden, wenn ein Debye-Hückel-Potential im Sinne des Poisson-Boltzmann-Cell Modells als Wechselwirkungspotential verwendet wird. Die ermittelten Phasengrenzen fluid-kristallin stehen erstmalig in guter Übereinstimmung mit Ergebnissen aus molekulardynamischen Simulationen, wenn die in der Torsionsresonanzspektroskopie bestimmte Wechselwirkungsenergie zu Grunde gelegt wird. Neben der Gleichgewichtsstruktur sind Aussagen zur Verfestigungskinetik möglich. Das gefundene Nukleationserhalten kann gut durch die klassische Nukleationstheorie beschrieben werden, wenn bei niedriger Unterkühlung der Schmelze ein Untergrund heterogener Keimung berücksichtigt wird. PTFE-Partikel zeigen auch bei hohen Konzentrationen nur geringfügige Mehrfachstreuung. Durch ihren Einsatz ist erstmals eine systematische Untersuchung des Glasübergangs in hochgeladenen ladungsstabilisierten Systemen möglich. Ladungsstabilisierte Kolloide unterscheiden sich vor allem durch ihre extreme Kristallisationstendenz von früher untersuchten Hartkugelsystemen. Bei hohen Partikelkonzentrationen (Volumenbrüche größer 10 Prozent) kann ein glasartiger Festkörper identifiziert werden, dessen physikalisches Verhalten die Existenz eines Bernalglases nahe legt. Der Glasübergang ist im Vergleich mit den in anderen kolloidalen Systemen und atomaren Systemen beobachteten Übergängen von sehr unterschiedlichem Charakter. Im verwendeten PTFE-System ist auf Grund der langreichweitigen stark repulsiven Wechselwirkung kein direkter Zugang des Glaszustandes aus der übersättigten Schmelze möglich. Der amorphe Festkörper entsteht hier aus einer nanokristallinen Phase. Die Keimrate steigt im zugänglichen Meßbereich annähernd exponentiell mit der Partikelanzahldichte, so daß man feststellen kann, daß der Glaszustand nicht durch Unterdrückung der Nukleation, sondern durch eine Forcierung derselben erreicht wird.

Strukturbildungsverhalten kettensteifer Polyelektrolyte in wässrigen Lösungen am Beispiel von Poly(para-phenylen)sulfonat

An einer Vielzahl biogener Polyelektrolyte, wie z.B. den Nukleinsäuren DNA und RNA sowie Proteinen, ist die Ausbildung von Strukturhierarchien durch Selbstorganisation von Strukturelementen zu beobachten. Dabei wird das Strukturbildungsverhalten durch eine Kopplung von Wechselwirkungen auf verschiedenen Längenskalen, den kurzreichweitigen ausgeschlossenen Volumen und den langreichweitigen elektrostatischen Wechselwirkungen (Coulomb-Wechselwirkungen), die wiederum durch eine Vielzahl mikroskopische Parameter (z.B. Konformation) beeinflusst werden, bestimmt. Durch diese Komplexität ist es nicht möglich, den für die Strukturbildung hochgeladener Systeme bedeutsamen Beitrag der elektrostatischen Wechselwirkungen isoliert zu betrachten. Aus diesem Grund werden zur Aufklärung von Wechselwirkungs- und Strukturbildungsmechanismen vereinfachte Modell-Systeme herangezogen. Eine Möglichkeit besteht in der Verwendung synthetischer, kettensteifer Polyelektrolyte. Im Rahmen dieser Arbeit wurde das Aggregationsverhalten wässriger Lösungen dodecylsubstituierter Poly(para-phenylen)sulfonate (PPPS) sowie die Beeinflussung der Strukturbildung durch verschiedene Parameter charakterisiert. Als Einflussparameter wurden einerseits die Gegenion-Spezies und andererseits die Temperatur- und Konzentrations-Abhängigkeit untersucht. Hierzu wurden wässrige Lösungen der freien Säuren der PPPS mit Molekulargewichten zwischen MW = 18 kg/mol bis 58 kg/mol mittels Licht-, Röntgen- und Neutronenstreuung sowie durch Licht-, Polarisations-, Transmissionselektronen- und Rasterkraftmikroskopie in einem Konzentrationsbereich von 0,0008 < c < 1,1 g/L untersucht.