819 resultados para pirolisi, PFU, syngas, char, impianto pilota, pneumatici
Resumo:
This master thesis aims at developing a new methodology for thermochemical degradation of dry coconut fiber (dp = 0.25mm) using laboratory rotating cylinder reactor with the goal of producing bio-oil. The biomass was characterized by infrared spectroscopy with Fourier transform FTIR, thermogravimetric analysis TG, with evaluation of activation energy the in non-isothermal regime with heating rates of 5 and 10 °C/min, differential themogravimetric analysis DTG, sweeping electron microscopy SEM, higher heating value - HHV, immediate analysis such as evaluated all the amounts of its main constituents, i.e., lignin, cellulose and hemicelluloses. In the process, it was evaluated: reaction temperature (450, 500 and 550oC), carrier gas flow rate (50 and 100 cm³/min) and spin speed (20 and 25 Hz) to condensate the bio-oil. The feed rate of biomass (540 g/h), the rotation of the rotating cylinder (33.7 rpm) and reaction time (30 33 min) were constant. The phases obtained from the process of pyrolysis of dry coconut fiber were bio-oil, char and the gas phase non-condensed. A macroscopic mass balance was applied based on the weight of each phase to evaluate their yield. The highest yield of 20% was obtained from the following conditions: temperature of 500oC, inert gas flow of 100 cm³/min and spin speed of 20 Hz. In that condition, the yield in char was 24.3%, non-condensable gas phase was 37.6% and losses of approximately 22.6%. The following physicochemical properties: density, viscosity, pH, higher heating value, char content, FTIR and CHN analysis were evaluated. The sample obtained in the best operational condition was subjected to a qualitative chromatographic analysis aiming to know the constituents of the produced bio-oil, which were: phenol followed by sirigol, acetovanilona and vinyl guaiacol. The solid phase (char) was characterized through an immediate analysis (evaluation of moisture, volatiles, ashes and fixed carbon), higher heating value and FTIR. The non-condensing gas phase presented as main constituents CO2, CO and H2. The results were compared to the ones mentioned by the literature.
Resumo:
Toxoplasmosis is one zoonosis caused by Toxoplasma gondii protozoan. Goats, amongst the production animals, are one of the species most susceptible to this parasite, being one them main involved agents in ovine and goat abortions, determining great economic losses and implications for public health, since the presence it parasite in the products of goat origin, consist in one of the main sources of infection for the man. In this study 244 blood samples in 8 farms situated in 4 cities from the Sertão do Cabugi region, Rio Grande do Norte State, northeast of Brazil and, tested by ELISA assay. The results had shown a prevalence of 47.13% for anti- T. gondii antibodies and a significant association between positivity and variable evaluated as age, locality and property. The IgG avidity assay evaluated in 115 positive samples was carried to discriminate acute and chronic infection. Twelve samples (10.4%) had presented antibodies of low avidity while 103 (89.6%) presented high avidity antibodies; indicating that most of the animals was precocious exposure to the parasite. Significant difference was verified only for the variable sex. We also evaluate the capacity of recombinant adenoviruses codifying SAG1, SAG2, SAG3 and CMV in inducing activation of specific immune response in goat. These 109 animals received 109 pfu of the AdSAG1, AdSAG2, AdSAG3, AdCMV or PBS in vaccine protocol with 3 immunizations. Serum samples of the each animal, before and after mmunization, had been submitted to the ELISA. The results demonstrate that the immunizations had induced the production of IgG antibodies specific against T. gondii proteins
Resumo:
The bio-oil obtained from the pyrolysis of biomass has appeared as inter-esting alternative to replace fossil fuels. The aim of this work is to evaluate the influence of temperature on the yield of products originating from the pyrolysis process of the powder obtained from the dried twigs of avelós (Euphorbia tirucalli), using a rotating cylinder reactor in laboratory scale. The biomass was treated and characterized by: CHNS, moisture, volatiles, fixed carbon and ashes, as well as evaluation of lignin, cellulose and hemicellulose, besides other instrumental techniques such as: FTIR, TG/DTG, DRX, FRX and MEV. The activation energy was evaluated in non-isothemichal mode with heating rates of 5 and 10 oC/min. The obtained results showed biomass as feedstock with potential for biofuel production, because presents a high organic matter content (78,3%) and fixed-carbon (7,11%). The activation energy required for the degradation of biomass ranged between 232,92 392,84 kJ/mol, in the temperature range studied and heating rate of 5 and 10°C/min. In the pyrolysis process, the influence of the reaction temperature was studied (350-520 ° C), keeping constant the other variables, such as, the flow rate of carrier gas, the centrifugal speed for the bio-oil condensationa, the biomass flow and the rotation of the reactor. The maximum yield of bio-oil was obtained in the temperature of 450°C. In this temperature, the results achieved where: content of bio-oil 8,12%; char 32,7%; non-condensed gas 35,4%; losts 23,8%; gross calorific value 3,43MJ/kg; pH 4,93 and viscosity 1,5cP. The chromatographic analysis of the bio-oil produced under these conditions shows mainly the presence of phenol (17,71%), methylciclopentenone (10,56%) and dimethylciclopentenone (7,76%)
Resumo:
The bio-oil obtained from the pyrolysis of biomass has appeared as inter-esting alternative to replace fossil fuels. The aim of this work is to evaluate the influence of temperature on the yield of products originating from the pyrolysis process of the powder obtained from the dried twigs of avelós (Euphorbia tirucalli), using a rotating cylinder reactor in laboratory scale. The biomass was treated and characterized by: CHNS, moisture, volatiles, fixed carbon and ashes, as well as evaluation of lignin, cellulose and hemicellulose, besides other instrumental techniques such as: FTIR, TG/DTG, DRX, FRX and MEV. The activation energy was evaluated in non-isothemichal mode with heating rates of 5 and 10 oC/min. The obtained results showed biomass as feedstock with potential for biofuel production, because presents a high organic matter content (78,3%) and fixed-carbon (7,11%). The activation energy required for the degradation of biomass ranged between 232,92 392,84 kJ/mol, in the temperature range studied and heating rate of 5 and 10°C/min. In the pyrolysis process, the influence of the reaction temperature was studied (350-520 ° C), keeping constant the other variables, such as, the flow rate of carrier gas, the centrifugal speed for the bio-oil condensationa, the biomass flow and the rotation of the reactor. The maximum yield of bio-oil was obtained in the temperature of 450°C. In this temperature, the results achieved where: content of bio-oil 8,12%; char 32,7%; non-condensed gas 35,4%; losts 23,8%; gross calorific value 3,43MJ/kg; pH 4,93 and viscosity 1,5cP. The chromatographic analysis of the bio-oil produced under these conditions shows mainly the presence of phenol (17,71%), methylciclopentenone (10,56%) and dimethylciclopentenone (7,76%)
Resumo:
Oxygen carriers are metal oxides which have the ability to oxidize and reduce easily by various cycles. Due to this property these materials are widely usedin Chemical-Looping Reforming processes to produce H2 and syngas. In this work supports based on MCM-41 and La-SiO2 were synthesized by hydrothermal method. After the synthesis step they were calcined at 550°C for 2 hours and characterized by TG, XRD, surface area using the BET method and FTIR spectroscopy. The deposition of active phase, in this case Nickel, took place in the proportions of 5, 10 and 20% by weight of metallic nickel, for use as oxygen carriers.The XRD showed that increasing in the content of Ni supported on MCM-41 resulted in a decrease in spatial structure and lattice parameter of the material. The adsorption and desorption curves of the MCM-41 samples exhibited variations with the increase of Ni deposited. Surface area, average pore diameter and wall density of silica showed significant changes , due to the increase of the active phase on the mesoporous material. By other hand, in the samples with La-SiO2 composition was not observed peaks characteristic of hexagonal structure, in the XRD diffractogram. The adsorption/desorption isotherms of nitrogen observed are type IV, characteristic of mesoporous materials. The catalytic test indicates that the supports have no influence in the process, but the nickel concentration is very important, because the results for minor concentration of nickel are not good. The ratio H2/O2 was close to 2, for all 15 cycles involving the test storage capacity of O2, indicating that the materials are effective for oxygen transport
Resumo:
One of the main applications of methane is in the production of syngas, a mixture of hydrogen and carbon monoxide. Procedures used in this process are steam reforming, CO2 reforming, partial oxidation and autothermal reforming. The present study evaluated and compared the behavior of nickel catalysts supported on mixed oxides of cerium and manganese in the partial oxidation of methane with that of nickel catalysts supported on mixed oxides of cerium and zirconium. Mixed oxides of cerium and zirconium or cerium and manganese were synthesized using two different preparation methods, the polymeric precursor based on Pechini method and combustion reaction using a microwave. This was followed by impregnation with nickel content of 15 %. Samples were calcined at 300, 800 and 900 °C and characterized by specific surface area (SSA), X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscopy (SEM), temperature programmed reduction (TPR) and the reaction of partial oxidation of methane. The specific areas of samples decrease with the rise in calcination temperature and after nickel impregnation. Metal-cerium solid solution was formed and the presence of other manganese species outside the solid solution structure was confirmed in the compound with the highest amounts of manganese oxides showed. With regard to scanning electron microscopy, supports based on cerium and zirconium prepared by Pechini method exhibited agglomerated particles without uniform geometry or visible pores on the surface. However, compounds containing manganese presented empty spaces in its structure. Through synthesis by combustion reaction, morphology acquired independently of the proposed composition demonstrated greater porosity in relation to Pechini synthesis. Although catalysts were prepared using different synthesis methods, the insertion of nickel showed very similar reduction profiles (TPR). In relation to nickel catalysts supported on mixed oxide of cerium and zirconium, there is an initial reduction of NiO species that present certain interaction with the support. This is followed by the reduction of Ce4+ in Ce3+ surface, with subsequent bulk reduction. For catalysts containing manganese, a reduction of nickel oxide species occurs, followed by two stages of reduction for species Mn2O3 in Mn3O4 and Mn3O4 in MnO, with subsequent reduction of bulk. With respect to partial oxidation reactions, the nickel catalyst supported on mixed oxide of cerium and zirconium, prepared using the Pechini method, exhibited CH4 conversion of approximately 80 %, with conversion of 81 % when prepared by combustion. This behavior continued for 10 hours of reaction. Manganese content was also found to directly influence catalytic activity of materials; the greater the manganese oxide content, the faster deactivation and destabilization occurred in the catalyst. In both synthesis methods, the nickel catalyst supported on mixed oxide of cerium and zirconium maintained an H2/CO ratio very close to 2 during the 10 hours of partial oxidation reaction. Samples containing manganese displayed smaller H2/CO ratios and lower performance in partial oxidation.
Resumo:
Platelet-derived growth factor-BB (PDGF-BB) stimulates repair of healing-impaired chronic wounds such as diabetic ulcers and periodontal lesions. However, limitations in predictability of tissue regeneration occur due, in part, to transient growth factor bioavailability in vivo. Here, we report that gene delivery of PDGF-B stimulates repair of oral implant extraction socket defects. Alveolar ridge defects were created in rats and were treated at the time of titanium implant installation with a collagen matrix containing an adenoviral (Ad) vector encoding PDGF-B (5.5 x 10(8) or 5.5 x 10(9) pfu ml (1)), Ad encoding luciferase (Ad-Luc; 5.5 x 10(9) pfu ml (1); control) or recombinant human PDGF-BB protein (rhPDGF-BB, 0.3 mg ml (1)). Bone repair and osseointegration were measured through backscattered scanning electron microscopy, histomorphometry, microcomputed tomography and biomechanical assessments. Furthermore, a panel of local and systemic safety assessments was performed. Results indicated that bone repair was accelerated by Ad-PDGF-B and rhPDGF-BB delivery compared with Ad-Luc, with the high dose of Ad-PDGF-B more effective than the low dose. No significant dissemination of the vector construct or alteration of systemic parameters was noted. In summary, gene delivery of Ad-PDGF-B shows regenerative and safety capabilities for bone tissue engineering and osseointegration in alveolar bone defects comparable with rhPDGF-BB protein delivery in vivo. Gene Therapy (2010) 17, 95-104; doi: 10.1038/gt.2009.117; published online 10 September 2009
Resumo:
Salmonella enterica serovar Enteritidis-lysing bacteriophages isolated from poultry or human sewage sources were used to reduce Salmonella Enteritidis in vitro and in experimentally infected chicks. Cocktails of 4 different bacteriophages obtained from commercial broiler houses (CB4O) and 45 bacteriophages from a municipal wastewater treatment plant (WT45O) were evaluated. In experiment 1, an in vitro crop assay was conducted with selected bacteriophage concentrations (105 to 101 pfu/mL) to determine ability to reduce Salmonella Enteritidis in the simulated crop environment. Following 2 h at 37 degrees C, CB40 or WT45O reduced Salmonella Enteritidis recovery by 1.5 or 5 log, respectively, as compared with control. However, CB40 did not affect total SE recovery after 6 h, whereas WT45O resulted in up to a 6-log reduction of Salmonella Enteritidis. In experiment 2, day-of-hatch chicks were challenged orally with 3 x 103 cfu /chick Salmonella Enteritidis and treated cloacally with 1 X 109 WT45O pfu/chick I h postchallenge. One hour later, chicks were treated or not with a commercially available probiotic (Floramax-B11). Both treatments significantly reduced Salmonella Enteritidis recovery from cecal tonsils at 24 h following vent lip application as compared with controls, but no additive effect was observed with the combination of bacteriophages and probiotic. In experiment 3, day-of-hatch chicks were challenged orally with 9 x 103 cfu/chick Salmonella Enteritidis and treated via oral gavage with I X 108 CB40 pfu/chick, 1.2 x 108 WT45O pfu/chick, or a combination of both, I h postchallenge. All treatments significantly reduced Salmonella Enteritidis recovered from cecal tonsils at 24 h as compared with untreated controls, but no significant differences were observed at 48 h following treatment. These data suggest that some bacteriophages can be efficacious in reducing SE colonization in poultry during a short period, but with the bacteriophages and methods presently tested, persistent reductions were not observed.
Resumo:
High efficiency gas turbine based systems, utility deregulation and more stringent environmental regulations strongly favor the use of natural gas over coal and other solid fuels in new electricity generators. Solid fuels could continue to compete, however, if a low cost gasifier fed by low cost feedstocks can be coupled with a gas turbine system. We examine on-site gasification of coal with other domestic fuels in an indirectly heated gasifier as a strategy to lower the costs of solid fuel systems. The systematics of gaseous pyrolysis yields assembled with the help of thermal measurement data and molecular models suggests blending carbonaceous fuels such as coal, coke or char with oxygenated fuels such as biomass, RDF, MSW, or dried sewage sludge. Such solid fuel blending can, with the help of inexpensive catalysts, achieve an optimum balance of volatiles, heating values and residual char thus reducing the technical demands upon the gasifier. Such simplifications should lower capital and operating costs of the gasifier to the mutual benefit of both solid fuel communities.
Resumo:
The CO2 reforming of CH4 was carried out over Ni catalysts supported on γ-Al2O3 and CeO 2-promoted γ-Al2O3. The catalysts were characterized by means of surface area measurements, TPR, CO2 and H2 chemisorption, XRD, SEM, and TEM. The CeO2 addition promoted an increase of catalytic activity and stability. The improvement in the resistance to carbon deposition is attributed to the highest CO2 adsorption presented by the CeO2 addition. The catalytic behavior presented by the samples, with a different CH4/CO2 ratio used, points to the CH4 decomposition reaction as the main source of carbon deposition.
Resumo:
Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)
Resumo:
The updraft biomass gasifiers currently available produce a gas with high tar content. For almost all downstream applications a substantial reduction of the tar concentration is required. The gravimetric tar concentration behavior in producer gas, obtained at a modified updraft fixed bed gasifier, was studied. The feedstock feeding system was modified respect to the traditional updraft gasification design in order to decrease the tar concentration in the producer gas; the material is feeding continuously through a conduit in the base of the reactor over the grate. The caloric power of the syngas obtained was slightly lower than the typical value for this type of reactor and the highest efficiency obtained for the woodchip gasification was 77%. The highest tar concentration obtained during the experiments was 1652.7 mg N m-3 during the first our of experiments, comparable with the smaller value reported for the updraft reactors, this value is reduced significantly after the stabilization of the gasification process in the reactor. The smaller value obtained was 21 mg N m-3. © 2013 Elsevier Ltd.
Resumo:
Pós-graduação em Direito - FCHS
Resumo:
Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)
Resumo:
Acumulam-se evidências presentemente, indicando que o efetivo controle das gastroenterites por rotavírus só poderá ser alcançado com o advento de um imunizante eficaz para uso nos primeiros meses de vida. Com o objetivo de avaliar a eficácia da vacina geneticamente rearranjada, rhesus-humana, tetravalente (RRV-TV, 4 X 10(4) pfu/dose) frente aos parâmetros clínicos mais relevantes das gastroenterites por rotavírus, procedeu-se ao reexame de 91 episódios diarréicos em crianças no âmbito de uma investigação prévia conduzida em Belém, Pará, Brasil. As informações para o estudo foram obtidas a partir de dados contidos em fichas utilizadas na rotina de vigilância dos episódios diarréicos, bem como daqueles com registro clínico diário enquanto persistisse a diarréia. A eficácia relativa foi especificamente avaliada frente aos seguintes indicadores clínicos de gravidade: a) duração da diarréia; b) número máximo de evacuações líquidas/semilíquidas por dia; c) duração dos vômitos; d) número máximo de vômitos/24h; e) febre (temperatura retal); f) desidratação; e g) necessidade de tratamento. A gravidade clínica global das gastroenterites por rotavírus foi determinada por um sistema de escores (somatória máxima de 20 pontos) que permitiu classificar os episódios diarréicos em: leves (0-8), moderados a severos (9-14) e muito graves (>14). Uma significativa (p<0,05) proteção conferida pela RRV-TV foi observada em cinco das sete condições clínicas avaliadas, quais sejam: a) duração da diarréia (episódios puros, eficácia de 52%); b) número máximo de evacuações líquidas/semilíquidas por dia (todos os episódios, 42% e os puros, 53%); c) número máximo de vômitos (todos, 56% e os puros, 62%); d) desidratação (todos, 46%) Elevados índices de proteção foram obtidos frente aos episódios associados ao sorotipo G2, durante o segundo ano de acompanhamento, se considerados o número máximo e a duração de vômitos: 90% e 100% respectivamente. Ainda em relação ao tipo G2, a eficácia cumulativa foi de 100% contra os episódios com escore clínico >14. Taxas similares de eficácia frente às infecções mistas (35%) e puras (37%) foram registradas nos dois anos de estudo. Embora não se tenha registrado proteção quanto aos casos leves (escores de 0 a 8), a RRV0TV foi 75% (p=0,02) eficaz contra os episódios mais graves de gastroenterites por rotavírus; houve tendência à proteção contra todos os quadros diarréicos e os puros, com escores clínicos de 9 a 14: 44% (p=0,06) e 45% (p=0,08), respectivamente. Os resultados do estudo sustentam o conceito vigente de que a RRV-TV parece proteger seletivamente contra os quadros diarréicos revestidos de maior gravidade clínica.