Opaque Layer Firing Temperature and Aging Effect on the Flexural Strength of Ceramic Fused to Cobalt-Chromium Alloy

Purpose: To evaluate the effect of the opaque layer firing temperature and mechanical and thermal cycling on the flexural strength of a ceramic fused to commercial cobalt-chromium alloy (Co-Cr). The hypotheses were that higher opaque layer temperatures increase the metal/ceramic bond strength and that aging reduces the bond strength.Materials and Methods: Metallic frameworks (25 x 3 x 0.5 mm(3); ISO 9693) (N = 60) were cast in Co-Cr and airborne-particle abraded (Al(2)O(3): 150 mu m) at the central area of the frameworks (8 x 3 mm(2)) and divided into three groups (N = 20), according to the opaque layer firing temperature: Gr1 (control)-900 degrees C; Gr2-950 degrees C; Gr3-1000 degrees C. The opaque ceramic (Opaque, Vita Zahnfabrick, Bad Sackingen, Germany) was applied, and the glass ceramic (Vita Omega 900, Vita Zahnfabrick) was fired onto it (thickness: 1 mm). While half the specimens from each group were randomly tested without aging (water storage: 37 degrees C/24 hours), the other half were mechanically loaded (20,000 cycles; 50 N load; distilled water at 37 degrees C) and thermocycled (3000 cycles; 5 degrees C to 55 degrees C, dwell time: 30 seconds). After the flexural strength test, failure types were noted. The data were analyzed using 2-way ANOVA and Tukey's test (alpha = 0.05).Results: Gr2 (19.41 +/- 5.5 N) and Gr3 (20.6 +/- 5 N) presented higher values than Gr1 (13.3 +/- 1.6 N) (p = 0.001). Mechanical and thermal cycling did not significantly influence the mean flexural strength values (p > 0.05). Increasing the opaque layer firing temperature improved the flexural bond strength values (p < 0.05). The hypotheses were partially accepted.Conclusion: Increasing of the opaque layer firing temperature improved the flexural bond strength between ceramic fused to Co-Cr alloy.

Temperature Effect on the Structure and Formation Kinetics of Vinyltriethoxysilane-Derived Organic/Silica Hybrids

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

New phosphinate ligand synthesis and its effect on optical properties of the europium beta-diketonate complex

The synthesis and characterization of a new organic ligand monooctyldiphenylphosphinate (L) is described, as well as a new Eu(3+) diketonate complex [Eu(tta)(3)(L)(2)] (tta = thenoyltrifluoracetone). The ligand (L) was formed by substitution reaction (80% yield) and characterized by uni- and bidimensional (1)H, (13)C and (31)P NMR experiments, to confirm its molecular structure. The coordination of (L) to Eu(3+) in the complex [Eu(tta)(3)(L)(2)] was confirmed by FT-IR spectra. The emission spectra present the same profile when excited in Eu(3+) or in the ligands, suggesting an energy transfer from ligands to Eu(3+) ions. The emission spectra of the precursor [Eu(tta)(3)(H(2)O)(2)], and [Eu(tta)(3)(L(2))] present bands arising from f-f intra-configurational transitions. The only (5)D(0)-(7)F(0) transition shows the presence of at least one site without symmetry center. The FWHM of such transition is 7 cm(-1) and 57 cm(-1) for [Eu(tta)(3)(H(2)O)(2)] and [Eu(tta)(3)(L)(2)] complexes, respectively. This widening is provided by the presence of large groups around Eu(3+) ion. The calculated intensity parameters Omega(2) and Omega(4) show that the interaction features between center-ion and ligand are different; the small value of Omega(4) is related to long range effects of alkyl chain. The Langmuir isotherms of this ligand and complex have been investigated although their hydrolysis in water subphase does not allow stable monolayers. (C) 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Antinociceptive effect on mice of the hydroalcoholic fraction and (-) epicatechin obtained from Combretum leprosum Mart & Eich

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Grain size effect on the electrical response of SnO2 thin and thick film gas sensors

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Adhesives with different pHs: Effect on the MTBS of chemically activated and light-activated composites to human dentin

Purpose: To evaluate the bond strength between human dentin and composites, using two light-activated single-bottle total-etch adhesive systems with different pHs combined with chemically activated and light-activated-composites. The tested hypothesis was that the dentin bond strength is not influenced by an adhesive system of low pH, combined with chemically activated or light-activated composites. Material and Method: Flat dentin surfaces of twenty-eight human third molars were allocated in 4 groups (n=7), depending on the adhesive system: (One Step Plus-OS and Prime & Bond NT-PB) and composite (light-activated Filtek Z-100 [Z100] and chemically activated Bisfil 2B [B2B]). Each adhesive system was applied on acid-etched dentin and then one of the composites was added to form a 5 mm-high resin block. The specimens were stored in tap water (37 degrees C/24 h) and sectioned into two axes, x and y. This was done with a diamond disk under coolant irrigation to obtain beams with a cross-section area of approximately 0.8 mm(2). Each specimen was then attached to a custom-made device and submitted to the microtensile test (1 mm.min(-1)). Data were analyzed using two-way ANOVA and Tukey's tests (p<0.05). Results: the anticipated hypothesis was not confirmed (p<0.0001). The bond strengths (MPa) were not statistically different between the two adhesive systems when light-activated composite was used (OS+Z100 = 24.7 +/- 7.1(a); PB+Z100 = 23.8 +/- 5.7(a)). However, with use of the chemically activated composite (B2B), PB (7.8 +/- 3.6(b) MPa) showed significantly lower dentin bond strengths than OS (32.2 +/- 7.6(a)). Conclusion: the low pH of the adhesive system can affect the bond of chemically activated composite to dentin. on the other hand, under the present conditions, the low pH did not seem to affect the bond of light-activated composites to dentin significantly.

Dark energy parametrizations and their effect on dark halos

There are a plethora of dark energy parametrizations that can fit current supernovae Ia data. However, these data are only sensitive to redshifts up to order one. In fact, many of these parametrizations break down at higher redshifts. In this paper we study the effect of dark energy models on the formation of dark halos. We select a couple of dark energy parametrizations which are sensible at high redshifts and compute their effect on the evolution of density perturbations in the linear and non-linear regimes. Using the Press-Schechter formalism we show that they produce distinguishable signatures in the number counts of dark halos. Therefore, future observations of galaxy clusters can provide complementary constraints on the behaviour of dark energy.

Effects of 10% carbamide peroxide bleaching materials on enamel microhardness

Purpose: To evaluate the microhardness of enamel treated with two different 10% carbamide peroxide bleaching materials at different time intervals. Materials and Methods: Two bleaching agents were analyzed: Opalescence (OPA) and Rembrandt (REM). The control group (CON) consisted of dental fragments maintained in artificial saliva. Bleaching was accomplished for 8 hrs per day and stored during the remaining time in an individual recipient with artificial saliva. Enamel microhardness testing was performed before the initial exposure to the treatments and after 1, 7, 14, 21, 28, 35 and 42 days. Results: the ANOVA, followed by the Bartlet and Tukey tests, showed significant differences for treatments (P < 0.00001) from day 7-day 42. From the 7th to the 14th day, OPA presented an increase of enamel microhardness over time while REM presented a decrease of microhardness. Statistical differences were not found between REM and the control group (OPA > CON = REM). From the 21st-35th day, enamel fragments bleached with OPA and REM presented a decrease of microhardness. Statistical differences of microhardness were verified among all the treatments (OPA > CON > REM). on the day 42, statistical differences were not found between OPA and the control group, but they were found between REM and the control group (OPA = CON > REM). The polynomial regression showed an increase of microhardness for OPA until the 21st day, followed by a decrease of microhardness up to the 42nd day. A decrease of microhardness for REM was verified. There were alterations in enamel microhardness as a function of bleaching time when using the two different 10% carbamide peroxide whiteners. Over a 42-day treatment time, bleaching with REM agent caused a decrease in enamel microhardness. The OPA agent initially increased the microhardness, then returned to the control level. Different bleaching materials with the same concentration of carbamide peroxide have different effects on the enamel.