Adolescents et cigarettes électroniques [Adolescents and electronic cigarettes].

L'usage de cigarettes électroniques (vapotage) augmente chez les jeunes et les professionnels de la santé se sentent démunis. Ce court article donne quelques informations pratiques. L'usage (vapotage) de cigarettes électroniques (e-cigarettes) est un phénomène relativement récent qui est en train de prendre une ampleur inattendue, surtout chez les jeunes. Bien que les taux de prévalence soient extrêmement variables d'un pays à l'autre, ils sont en net augmentation: tant parmi ceux qui les ont seulement essayées que chez ceux qui les utilisent habituellement, les taux de prévalence ont doublé ou presque triplé en à peine une année. En outre, une proportion notable d'utilisateurs d'e-cigarettes (de 8 à 33% selon les études)n'avaient jamais fumé de cigarettes conventionnelles. Ce phénomène pourrait faire des e-cigarettes la porte d'entrée au tabagisme parmi les jeunes. Adolescents and electronic cigarettes: The use of electronic cigarettes (vaping) is increasing among young people and health professionals feel ill-prepared. This short article provides some practical information The use of electronic cigarettes (vaping) is increasing among young people and health professionals feel ill-prepared. This short article provides some practical information.

Hot wire configuration for depositing device grade nano-crystalline silicon at high deposition rate

The University of Barcelona is developing a pilot-scale hot wire chemical vapor deposition (HW-CVD) set up for the deposition of nano-crystalline silicon (nc-Si:H) on 10 cm × 10 cm glass substrate at high deposition rate. The system manages 12 thin wires of 0.15-0.2 mm diameter in a very dense configuration. This permits depositing very uniform films, with inhomogeneities lower than 2.5%, at high deposition rate (1.5-3 nm/s), and maintaining the substrate temperature relatively low (250 °C). The wire configuration design, based on radicals' diffusion simulation, is exposed and the predicted homogeneity is validated with optical transmission scanning measurements of the deposited samples. Different deposition series were carried out by varying the substrate temperature, the silane to hydrogen dilution and the deposition pressure. By means of Fourier transform infrared spectroscopy (FTIR), the evolution in time of the nc-Si:H vibrational modes was monitored. Particular importance has been given to the study of the material stability against post-deposition oxidation.

Searching electronic marketplaces

The main objective of this thesis was to analyze the usability of registers and indexes of electronic marketplaces. The work is focused on UDDI-based electronic marketplaces, which are standardized by the W3C. UDDI-registers are usable in intranets, extranets and in Internet. Using UDDI-registers Web-services can be searched in many ways, including alphabetical and domain specific searches. Humans and machines can use the features UDDI-registers. The thesis deals the design principles, architectures and specifications of UDDI-registers. In addition, the thesis includes the design and the specifications of an electronic marketplace developed for supporting electronic logistics services.

Software process improvement using an electronic process guide

Kasvava kiinnostus ohjelmistojen laatua kohtaan on herättänyt ohjelmistoprosesseihin ja niiden kehittämiseen kohdistuvaa huomiota viime vuosina. Ohjelmistoyritykset ympäri maailmaa ovat ottaneet käyttöön ohjelmistoprosessin kehittämismalleja, kuten CMM ja SPICE, pyrkiessään kohti parempilaatuisia ohjelmistotuotteita. Samalla on huomattu, että tehokas prosessien parantaminen ja suorittaminen tarvitsee tuekseen kuvauksen prosessista, jotta prosessin perusteellinen ymmärtäminen ja kommunikointi olisi mahdollista. Ohjelmistoprosesseja voidaan kuvata monilla eri tavoilla. Prosessiopas on prosessin esitysmuoto, jonka päätarkoituksena on helpottaa prosessin ymmärtämistä ja kommunikointia. Elektroninen prosessiopas on Web-teknologiaa hyödyntävä prosessiopas. Tässä työssä luodaan kehitysympäristö elektronisille prosessioppaille, joiden tarkoituksena on tukea ohjelmistoprosessin kehittämistä ja suorittamista. Ympäristö mahdollistaa ohjelmistoprosessinmallintamisen sekä yksilöllisten oppaiden luomisen ja muokkaamisen. Kehitysympäristöä käytetään mallintamaan tietoliikenneohjelmistoja valmistavan yrityksen ohjelmistoprosessia sekä luomaan elektronisia prosessioppaita tukemaan prosessin kehitystä ja suorittamista. Lopuksi pohditaan prosessioppaiden tarjoamaa tukea sekä mahdollisuuksia kohdeyrityksessä.

Electronic Data Interchange in Logistics Processes

Tämän diplomityön tarkoituksena oli tehdä selvitys EDI:in liittyvistä vaikutuksista, tarpeista ja eduista sekä valmistella Oracle Applications- toiminnanohjausjärjestelmän EDI Gateway- modulin ottamista tuotantokäyttöön. Tietoa tarvekartoitukseen saatiin keskustelujen avulla. Uusia kaupallisista lähtökohdista johdettuja, yritysten väliseen kaupankäyntiin ja internet-teknologian hyödyntämiseen kehitettyjä aloitteita käsiteltiin EDI-näkökulmasta tulevaisuutta varten. Ajankohtaisinta tietoa tätä diplomityötä varten löydettiin myös internetistä. Tämän jälkeen oli mahdollista toteuttaa sopivan laaja mutta rajattu EDI pilottiprojekti EDI-konseptin luomista varten. EDI:n vaikutuksiin ostossa keskityttiin tässä diplomityössä enemmän ja EDI:ä päätettiin soveltaa aluksi ostotilauksissa. EDI:n hyötyjä on vaikea mitata numeerisesti. Suurta määrää rahaa tai tuoteyksiköitä on käsiteltävä EDI-partnerin kanssa riittävän usein. EDI:n käyttöönottovaiheessa pääongelmat ovat sovelluksiin liittyviä tietotekniikkaongelmia. Selvityksistä ja EDI-projektista saatu tieto on mahdollista hyödyntää jatkokehityksessä. Lisätoimenpiteitä tarvitaan kokonaan toimivan järjestelmän luomiseksi.

Optoelectronic studies in nanocrystalline silicon Schottky diodes obtained by Hot-Wire Chemical Vapour Deposition

The very usual columnar growth of nanocrystalline silicon leads to electronic transport anisotropies. Whereas electrical measurements with coplanar electrodes only provide information about the electronic transport parallel to the substrate, it is the transverse transport which determines the collection efficiency in thin film solar cells. Hence, Schottky diodes on transparent electrodes were obtained by hot-wire CVD in order to perform external quantum efficiency and surface photovoltage studies in sandwich configuration. These measurements allowed to calculate a transverse collection length, which must correlate with the photovoltaic performance of thin film solar cells. Furthermore, the density of charge trapped at localized states in the bandgap was estimated from the voltage dependence of the depletion capacitance of these rectifying contacts.

Spatial radial maze procedures and setups to dissociate local and distal relational spatial frameworks in humans.

BACKGROUND: Radial maze tasks have been used to assess optimal foraging and spatial abilities in rodents. The spatial performance was based on a capacity to rely on a configuration of local and distant cues. We adapted maze procedures assessing the relative weight of local cues and distant landmarks for arm choice in humans. NEW METHOD: The procedure allowed testing memory of places in four experimental setups: a fingertip texture-groove maze, a tactile screen maze, a virtual radial maze and a walking size maze. During training, the four reinforced positions remained fixed relative to local and distal cues. During subsequent conflict trials, these frameworks were made conflictive in the prediction of reward locations. RESULTS: Three experiments showed that the relative weight of local and distal relational cues is affected by different factors such as cues' nature, visual access to the environment, real vs. virtual environment, and gender. A fourth experiment illustrated how a walking maze can be used with people suffering intellectual disability. COMPARISON WITH EXISTING METHODS: In our procedure, long-term (reference) and short-term (working) memory can be assessed. It is the first radial task adapted to human that enables dissociating local and distal cues, to provides an indication as to their relative salience. Our mazes are moveable and easily used in limited spaces. Tasks are performed with realistic and spontaneous though controlled exploratory movements. CONCLUSION: Our tasks enabled highlighting the use of different strategies. In a clinical perspective, considering the use of compensatory strategies should orient towards adapted behavioural rehabilitation.

Electronic transport in low temperature nanocrystalline silicon thin-film transistors obtained by Hot-Wire CVD

Hydrogenated nanocrystalline silicon (nc-Si:H) obtained by hot-wire chemical vapour deposition (HWCVD) at low substrate temperature (150 °C) has been incorporated as the active layer in bottom-gate thin-film transistors (TFTs). These devices were electrically characterised by measuring in vacuum the output and transfer characteristics for different temperatures. The field-effect mobility showed a thermally activated behaviour which could be attributed to carrier trapping at the band tails, as in hydrogenated amorphous silicon (a-Si:H), and potential barriers for the electronic transport. Trapped charge at the interfaces of the columns, which are typical in nc-Si:H, would account for these barriers. By using the Levinson technique, the quality of the material at the column boundaries could be studied. Finally, these results were interpreted according to the particular microstructure of nc-Si:H.

Managing the Sick Child in the Era of Declining Malaria Transmission: Development of ALMANACH, an Electronic Algorithm for Appropriate Use of Antimicrobials.

OBJECTIVE: To review the available knowledge on epidemiology and diagnoses of acute infections in children aged 2 to 59 months in primary care setting and develop an electronic algorithm for the Integrated Management of Childhood Illness to reach optimal clinical outcome and rational use of medicines. METHODS: A structured literature review in Medline, Embase and the Cochrane Database of Systematic Review (CDRS) looked for available estimations of diseases prevalence in outpatients aged 2-59 months, and for available evidence on i) accuracy of clinical predictors, and ii) performance of point-of-care tests for targeted diseases. A new algorithm for the management of childhood illness (ALMANACH) was designed based on evidence retrieved and results of a study on etiologies of fever in Tanzanian children outpatients. FINDINGS: The major changes in ALMANACH compared to IMCI (2008 version) are the following: i) assessment of 10 danger signs, ii) classification of non-severe children into febrile and non-febrile illness, the latter receiving no antibiotics, iii) classification of pneumonia based on a respiratory rate threshold of 50 assessed twice for febrile children 12-59 months; iv) malaria rapid diagnostic test performed for all febrile children. In the absence of identified source of fever at the end of the assessment, v) urine dipstick performed for febrile children <2 years to consider urinary tract infection, vi) classification of 'possible typhoid' for febrile children >2 years with abdominal tenderness; and lastly vii) classification of 'likely viral infection' in case of negative results. CONCLUSION: This smartphone-run algorithm based on new evidence and two point-of-care tests should improve the quality of care of <5 year children and lead to more rational use of antimicrobials.

Effect of humeral stem design on humeral position and range of motion in reverse shoulder arthroplasty.

PURPOSE: The impacts of humeral offset and stem design after reverse shoulder arthroplasty (RSA) have not been well-studied, particularly with regard to newer stems which have a lower humeral inclination. The purpose of this study was to analyze the effect of different humeral stem designs on range of motion and humeral position following RSA. METHODS: Using a three-dimensional computer model of RSA, a traditional inlay Grammont stem was compared to a short curved onlay stem with different inclinations (155°, 145°, 135°) and offset (lateralised vs medialised). Humeral offset, the acromiohumeral distance (AHD), and range of motion were evaluated for each configuration. RESULTS: Altering stem design led to a nearly 7-mm change in humeral offset and 4 mm in the AHD. Different inclinations of the onlay stems had little influence on humeral offset and larger influence on decreasing the AHD. There was a 10° decrease in abduction and a 5° increase in adduction between an inlay Grammont design and an onlay design with the same inclination. Compared to the 155° model, the 135° model improved adduction by 28°, extension by 24° and external rotation of the elbow at the side by 15°, but led to a decrease in abduction of 9°. When the tray was placed medially, on the 145° model, a 9° loss of abduction was observed. CONCLUSIONS: With varus inclination prostheses (135° and 145°), elevation remains unchanged, abduction slightly decreases, but a dramatic improvement in adduction, extension and external rotation with the elbow at the side are observed.

The Electronic Structure of Co-Sputtered Zinc Indium Tin Oxide Thin Films

Zinc indium tin oxide (ZITO) transparent conductive oxide layers were deposited via radio frequency (RF) magnetron co-sputtering at room temperature. A series of samples with gradually varying zinc content was investigated. The samples were characterized with x-ray and ultraviolet photoemission spectroscopy (XPS, UPS) to determine the electronic structure of the surface. Valence and conduction bands maxima (VBM, CBM), and work function were determined. The experiments indicate that increasing Zn content results in films with a higher defect rate at the surface leading to the formation of a degenerately doped surface layer if the Zn content surpasses 50%. Furthermore, the experiments demonstrate that ZITO is susceptible to ultraviolet light induced work function reduction, similar to what was earlier observed on ITO and TiO2 films.

Electronic properties of a quantum wire with arbitrary bending angle

The electron transmission and bound state properties of a quantum wire with a sharp bend at arbitrary angle are studied, extending results on the right angle sharp bend (the L¿shaped wire). These new results are compared to those of a similar structure, the circular bend wire. The possibility of using a bent wire to perform transistor action is also discussed.

Considering tourist perceptions and network configuration in destination management

The competitiveness of tourism destinations is a relevant issue for tourism studies, moreso, is a key element on the daily basis of tourism destinations. In this sense, the management of tourism destinations is essential to maintain competitive advantages. In this article tourism destination is considered as a relational network, where interaction and cooperation is needed among tourist agents, to achieve major levels of competitive advantage and a more effective destination management system. In addition, the perceptions of tourists are obtained from two main sources. The first one is the social construction of a tourism destination previous to the visit and the second one is obtained from the interaction between tourists and tourism destination agents during the visit. In this sense, the management of tourism destination to emit a homogenous and collective image is a factor that can reduce the gap if dissatisfaction from the previous and real tourist perception. The discussion is centered on the relationship within a destination, between the supply network and the targeted demand, considering these two approaches jointly, to benefit destination management. The main result is a conceptual model that shows how tourism agents and tourists in the tourism destination interact to improve the destination competitiveness

The Evolution of the European Regulatory Framework for Electronic Communications

The paper reviews the historical transformation of the European regulatory framework for electronic communications from the era dominated by state-owned enterprises to the presence of regulated competition. In the course of these developments, the vision of the roles of the public and private sectors in electronic communications changed in expected and unexpected ways. While the period is characterized by a shift toward less direct state intervention, the intensity of regulation has increased in many areas. Most recently, in the wake of the financial crisis, new forms of state intervention can be observed, including public investment in communications infrastructure and public-private partnerships. As a result of the reforms, Europe has been able to achieve major successes but it also suffered unanticipated setbacks compared to other regions. The European Union emerged as the global leader in mobile communications during the 1990s and was able to roll-out first-generation broadband access networks more rapidly than many of its peers. Recently, however, Europe as a whole has not performed as well in deploying next-generation networks and advanced mobile communications services. The paper offers a political-economic explanation for these developments and assesses their effects on the performance of the European electronic communications sector and the economy. From this analysis, the European model emerges as a unique institutional arrangement with peculiar advantages and disadvantages. Once these are recognized, sensible next steps to build the strengths while avoiding the weaknesses of the model can be seen more clearly.