Optimisation of data analysis method for a fluidized bed combustion test rig

Nowadays the used fuel variety in power boilers is widening and new boiler constructions and running models have to be developed. This research and development is done in small pilot plants where more faster analyse about the boiler mass and heat balance is needed to be able to find and do the right decisions already during the test run. The barrier on determining boiler balance during test runs is the long process of chemical analyses of collected input and outputmatter samples. The present work is concentrating on finding a way to determinethe boiler balance without chemical analyses and optimise the test rig to get the best possible accuracy for heat and mass balance of the boiler. The purpose of this work was to create an automatic boiler balance calculation method for 4 MW CFB/BFB pilot boiler of Kvaerner Pulping Oy located in Messukylä in Tampere. The calculation was created in the data management computer of pilot plants automation system. The calculation is made in Microsoft Excel environment, which gives a good base and functions for handling large databases and calculations without any delicate programming. The automation system in pilot plant was reconstructed und updated by Metso Automation Oy during year 2001 and the new system MetsoDNA has good data management properties, which is necessary for big calculations as boiler balance calculation. Two possible methods for calculating boiler balance during test run were found. Either the fuel flow is determined, which is usedto calculate the boiler's mass balance, or the unburned carbon loss is estimated and the mass balance of the boiler is calculated on the basis of boiler's heat balance. Both of the methods have their own weaknesses, so they were constructed parallel in the calculation and the decision of the used method was left to user. User also needs to define the used fuels and some solid mass flowsthat aren't measured automatically by the automation system. With sensitivity analysis was found that the most essential values for accurate boiler balance determination are flue gas oxygen content, the boiler's measured heat output and lower heating value of the fuel. The theoretical part of this work concentrates in the error management of these measurements and analyses and on measurement accuracy and boiler balance calculation in theory. The empirical part of this work concentrates on the creation of the balance calculation for the boiler in issue and on describing the work environment.

Decomposition of differences in PISA results in middle income countries

Programme for International Student Assessment

Decomposition of Ruppia cirrhosa (Petagna) Grande in the sediment of a coastal lagoon

The decomposition process of Ruppia cirrhosa was studied in a Mediterranean coastal lagoon in the Delta of the River Ebro (NE Spain). Leaves and shoots of Ruppia were enclosed in 1 mm-mesh and 100 pm-mesh litter bags to ascertain the effect of detritivores, macroinvertebrates, and bacteria and fungi, respectively. Changes in biomass and carbon, and, nitrogen and phosphorus concentrations in the detritus were studied at the sediment-water interface and in the sediment. Significant differences in biomass decay were observed between the two bag types. Significant differences in decomposition were observed between the two experimental conditions studied using 100 pm-mesh bags. These differences were not significant when using the 1 mm-mesh bags. The carbon content in the detritus remained constant during the decomposition process. The percentage of nitrogen increased progressively from an initial 2.4 % to 3 %. The percentage of phosphorus decreased rapidly during the first two days of decomposition from an initial 0.26 % to 0.17 %. This loss is greater in the sediment than in the water column or at the sediment-water interface. From these results we deduce that the activity of microorganisms seems to be more important in the sediment than in the water-sediment interface, and that grazing by macroinvertebrates has less importance in the sediment than in the water column.

Development of a Testing Method for Convertibility of Paperboard

Työssä tutkittiin muovattujen kartonkivuokien sekä muovattujen kartonkinäytteiden rinnastettavuutta. Puristusvaiheen prosessiolosuhteiden miellettiin vaikuttavan eniten multidimensionaliseen muodonmuutokseen. Multidimensionaalista muodonmuutosta simuloitiin uudella muovaamiseen soveltuvalla muovauslaitteella. Kirjallisuusosassa keskeisiä teemoja ovat kartongin muovaus sekä kuitupohjaisen materiaalin reologinen käyttäytyminen. Kirjallisuusosassa esitellään lisäksi yksi tekninen sovellus, jonka avulla kyetään ennustamaan kuitumateriaalin muovautuvuutta sekä mittaamaan tapahtunutta muodonmuutosta. Prosessiparametrien teoreettista vaikutustakuituihin tarkastellaan myös kirjallisuusosassa. Kokeellisessa osassa toteutettiin kartonkivuokien valmistus puristamalla. Vastaavilla prosessiparametreilla muovattiin myös pienemmät testinäytteet. Perinteiset yksidimensionaliset deformaatiomittaukset toteutettiin lujuusominaisuuksien laboratoriomäärityksinä. Myös kitka, joka toimii tärkeänä muuttujana prässäysprosessissa, mitattiin laboratorio-olosuhteissa. Tämän työn tulokset osoittavat uuden kehitetyn muovausmenetelmän toimivuuden. Asema-voima kuvaajat ovat selkeitä sekä helposti luettavia. Tuloksissa havaittiin materiaalin muovauspotentiaalin sekä asema-voima kuvaajan välillä vallitseva yhteys. Erittäin merkittävä huomio oli myös, että muovipäällystetyllä kartongilla oli yhteys päällystämättömän kartongin asema-voima kuvaajaan. Tämä tulos osoittaa, että muovipäällystetyn kartongin muovautuvuutta voi olla mahdollista ennustaa pohjakartongin muovautuvuustulosten perusteella. Perinteiset yksidimensionaliset laboratoriomittaukset eivät kykene antamaan riittävää informaatiota muovautuvuuden ennustamiseen. Tästä näkökulmasta on tärkeää että kartongin multidimensionalista muotoutuvuutta voidaankin tutkia kehitetyllä muovausmenetelmällä.

Development of a harmonised method for the profiling of amphetamine

Résumé : Cette thèse de doctorat est le fruit d'un projet de recherche européen financé par le quatrième programme cadre de la Commission Européenne (DG XII, Standards, Measurement and Testing). Ce projet, dénommé SMT-CT98-2277, a été financé pour la partie suisse par l'Office Fédéral de l'Education et de la Science (OFES, Berne, Suisse). Le but de ce projet était de développer une méthode harmonisée et collaborativement testée pour le profilage des impuretés de l'amphétamine illicite par chromatographie capillaire en phase gazeuse. Le travail a été divisé en sept phases majeures qui concernaient la synthèse de l'amphétamine, l'identification d'impuretés, l'optimisation de la préparation de l'échantillon et du système chromatographique, la variabilité des résultats, l'investigation de méthodes mathématiques pour la classification et la comparaison de profils et finalement l'application de la méthode à des réels échantillons illicites. La méthode résultant de ce travail n'a pas seulement montré que les données étaient interchangeables entre laboratoires mais aussi qu'elle était supérieure en de nombreux points aux méthodes préalablement publiées dans la littérature scientifique. Abstract : This Ph.D. thesis was carried out in parallel to an European project funded by the fourth framework program of the European Commission (DG XII, Standards, Measurement and Testing). This project, named SMT-CT98-2277 was funded, for the Swiss part, by the Federal Office of Education and Science (OFES, Bern, Switzerland). The aim of the project was to develop a harmonised, collaboratively tested method for the impurity profiling of illicit amphetamine by capillary gas chromatography. The work was divided into seven main tasks which deal with the synthesis of amphetamine, identification of impurities, optimization of sample preparation and of the chromatographic system, variability of the results, investigation of numerical methods for the classification and comparison of profiles and finally application of the methodology to real illicit samples. The resulting method has not only shown to produce interchangeable data between different laboratories but was also found to be superior in many aspects to previously published methods.

Development of a shelling method to recover whole kernels of the Cutia nut (Couepia edulis)

The kernel of the cutia nut (castanha-de-cutia, Couepia edulis (Prance) Prance) of the western Amazon, which is consumed by the local population, has traditionally been extracted from the nut with a machete, a dangerous procedure that only produces kernels cut in half. A shelling off machine prototype, which produces whole kernels without serious risks to its operator, is described and tested. The machine makes a circular cut in the central part of the fruit shell, perpendicular to its main axis. Three ways of conditioning the fruits before cutting were compared: (1) control; (2) oven drying immediately prior to cutting; (3) oven drying, followed by a 24-hour interval before cutting. The time needed to extract and separate the kernel from the endocarp and testa was measured. Treatment 3 produced the highest output: 63 kernels per hour, the highest percentage of whole kernels (90%), and the best kernel taste. Kernel extraction with treatment 3 required 50% less time than treatment 1, while treatment 2 needed 38% less time than treatment 1. The proportion of kernels attached to the testa was 93%, 47%, and 8% for treatments 1, 2, and 3, respectively, and was the main reason for extraction time differences.

Surrogate science: The idol of a universal method for scientific inference

The application of statistics to science is not a neutral act. Statistical tools have shaped and were also shaped by its objects. In the social sciences, statistical methods fundamentally changed research practice, making statistical inference its centerpiece. At the same time, textbook writers in the social sciences have transformed rivaling statistical systems into an apparently monolithic method that could be used mechanically. The idol of a universal method for scientific inference has been worshipped since the "inference revolution" of the 1950s. Because no such method has ever been found, surrogates have been created, most notably the quest for significant p values. This form of surrogate science fosters delusions and borderline cheating and has done much harm, creating, for one, a flood of irreproducible results. Proponents of the "Bayesian revolution" should be wary of chasing yet another chimera: an apparently universal inference procedure. A better path would be to promote both an understanding of the various devices in the "statistical toolbox" and informed judgment to select among these.

Description and implementation of cut calculation-method in a sawmill

Työn tavoitteena oli kuvata ja ottaa käyttöön sahauseräkohtaisen kannattavuuden laskentamenetelmä sahalle, sekä tehdä laskentamalli menetelmän tueksi. Sahauksen peruskäsitteiden jälkeen työssä on esitelty sahan tuotantoprosessi. Tuotantoprosessi on kuvattu kirjallisuuden ja asiantuntijoiden haastattelujen perusteella. Seuraavaksi kartoitettiin hyötyjä ja vaikutuksia, mitä laskentamenetelmältä odotetaan.. Kustannuslaskennan teoriaa selvitettiin kirjallisuuslähteitä käyttäen silmälläpitäen juuri tätä kehitettävää laskentamenetelmää. Lisäksi esiteltiin Uimaharjun sahalla käytettävät ja laskentaan liittyvät laskenta- ja tietojärjestelmät.Nykyisin sahalla ei ole minkäänlaista menetelmää sahauseräkohtaisen tuloksen laskemiseksi. Pienillä muutoksilla sahan tietojärjestelmään ja prosessikoneisiin voidaan sahauserä kuljettaa prosessin läpi niin, että jokaisessa prosessin vaiheessa sille saadaan kohdistettua tuotantotietoa. Eri vaiheista saatua tietoa käyttämällä saadaan tarkasti määritettyä tuotteet, joita sahauserä tuotti ja paljonko tuotantoresursseja tuottamiseen kului. Laskentamalliin syötetään tuotantotietoja ja kustannustietoa ja saadaan vastaukseksi sahauserän taloudellinen tulos.Toimenpide ehdotuksena esitetään lisätutkimusta tuotantotietojen automaattisesta keräämisestä manuaalisen työn ja virheiden poistamiseksi. Suhteellisen pienillä panoksilla voidaan jokaiselle sahauserälle kerätä tuotantotiedot täysin automaattisesti. Lisäksi kehittämäni laskentamallin tilalle tulisi hankkia sovellus, joka käyttäisi paremmin hyväksi nykyisiä tietojärjestelmiä ja poistaisi manuaalisen työvaiheen laskennassa.

Synthesis, characterization and thermal decomposition of [Pd2 (C²-dmba) (µ-SO4) (SO2)2]

The bridged sulphate complex [Pd2 (C²,dmba) (µ-SO4) (SO2)2] has been obtained by reacting a saturated solution of SO2 in methanol and the cyclometallated compound [Pd(C²,N-dmba)(µ-N3)] 2; (dmba = N,N-dimethylbenzylamine), at room temperature for 24 h. Reaction product was characterized by elemental analysis, NMR comprising 13C{¹H} and ¹H nuclei and I.R. spectrum's measurements. Thermal behavior has been investigated and residual products identified by X-ray powder diffraction.

Preparation and thermal decomposition of copper(II), zinc(II) and cadmium(II) chelates with 8-hydroxyquinoline

When the compounds are heated in an inert atmosphere it can be verified the consecutive partial sublimation, fusion, partial volatilization and partial thermal decomposition of the anhydrous complexes. When in an oxidating atmosphere the above process is only verified to Cu(II) chelates. Anhydrous copper(II) complexes present a monoclinic structure in the b form and the volatilized compound in a a form. Zinc(II) and cadmium(II) hydrated complexes are isomorphous and they present different cell dimensions from those reported previously.

Síntese, caracterização e estudo das propriedades catalíticas e magnéticas de nanopartículas de Ni dispersas em matriz mesoporosa de SiO2

Nickel nanoparticles supported on amorphous silica ceramic matrix were synthesized by the polymeric precursor method. The nanostructure was characterized by NMR, BET, XRD, SEM, TEM, and flame atomic absorption spectrometry techniques. It was observed a dependence of the crystallite size on the thermal annealing, under a N2 atmosphere. The materials presented a high catalytic activity and selectivity upon the beta-pinene hydrogenation reaction. The magnetic hystereses were also correlated with the morphology of the processed material.

Dióxido de estanho nanoestruturado: síntese e crescimento de nanocristais e nanofitas

The objectives of this work are to supply a basic background on nanostructured materials and also to report about the obtaining of nanoparticles, mainly, tin dioxide nanocrystalline particles (obtained by using the polymeric precursor method) presenting a high stability against particle growth due to the usage of a metastable solid solution. The synthesis and growth of SnO2 nanoribbons by a carbothermal reduction process are also discussed.

Fotoluminescência e adsorção de CO2 em nanopartículas de CaTiO3 dopadas com lantânio

Ca1-xLa xTiO3 powders were prepared by the polymeric precursor method. X-ray diffraction (XRD), FT-Raman spectroscopy, transmission electron microscopy (TEM), and N2 and CO2 adsorption were used for the microstructural and surface characterization of the powders. Room temperature photoluminescence (PL) was observed in Ca1-xLa xTiO3 amorphous particles. The PL intensity of these powders was found to be dependent on the lanthanum molar concentration.

Síntese e caracterização de nanocompósitos Ni: SiO2 processados na forma de filmes finos

We have produced nanocomposite films of Ni:SiO2 by an alternative polymeric precursor route. Films, with thickness of ~ 1000 nm, were characterized by several techniques including X-ray diffraction, scanning electron microscopy, atomic force microscopy, flame absorption atomic spectrometry, and dc magnetization. Results from the microstructural characterizations indicated that metallic Ni-nanoparticles with average diameter of ~ 3 nm are homogeneously distributed in an amorphous SiO2 matrix. Magnetization measurements revealed a blocking temperature T B ~ 7 K for the most diluted sample and the absence of an exchange bias suggesting that Ni nanoparticles are free from an oxide layer.