Adsorption of hydrogen sulfide by modified cellulose nano/microcrystals

Hydrogen sulfide is toxic and hazardous pollutant. It has been under great interest for past few years because of all the time tighten environmental regulations and increased interest of mining. Hydrogen sulfide gas originates from mining and wastewater treatment systems have caused death in two cases. It also causes acid rains and corrosion for wastewater pipelines. The aim of this master thesis was to study if chemically modified cellulose nanocrystals could be used as adsorbents to purify hydrogen sulfide out from water and what are the adsorption capacities of these adsorbents. The effects of pH and backgrounds on adsorption capacities of different adsorbents are tested. In theoretical section hydrogen sulfide, its properties and different purification methods are presented. Also analytical detection methods for hydrogen sulfide are presented. Cellulose nano/microcrystals, properties, application and different modification methods are discussed and finally theory of adsorption and modeling of adsorption is shortly discussed. In experimental section different cellulose nanocrystals based adsorbents are prepared and tested at different hydrogen sulfide concentrations and in different conditions. Result of experimental section was that the highest adsorption capacity at one component adsorption had wet MFC/CaCO3. At different pH the adsorption capacities of adsorbents changed quite dramatically. Also change of hydrogen sulfide solution background did have effect on adsorption capacities. Although, when tested adsorbents’ adsorption capacities are compared to those find in literatures, it seems that more development of MFC based adsorbents is needed.

Chronic subdural hematoma: epidemiological and prognostic analysis of 176 cases

Objective : To characterize patients with chronic subdural hematoma undergoing surgery and to identify prognostic indicators. Methods : We conducted a retrospective analysis of patients diagnosed with chronic subdural hematoma (CSDH) undergoing surgical treatment. We analyzed: age, period from trauma to diagnostic imaging, pre and postoperative Glasgow coma scale, type of surgery, associated comorbidities, use of postoperative drainage and outpatient treatment. Results : The sample consisted of 176 patients, 126 male and 50 female patients (ratio 2.5 : 1), ages ranged from six months to 97 years, with an average of 59.3 years. CSDH was caused by trauma in 52% of patients, with the time from trauma to imaging averaging 25.05 days; 37.7% were hypertensive patients and 20% had a neurological disease. Eighty-five (48.3%) patients were elderly and altered consciousness was present in 63% of cases. Of the 91 (51.7%) non-elderly patients, 44% presented with headache, altered consciousness occurred in 40% and motor abnormalities in 27.5%. The CSDH was located on the right in 41%, left in 43% and bilaterally in 16% of patients. Conclusion : the change of consciousness was the most common clinical alteration in the elderly and headache in non-elderly. The most associated comorbidity was the arterial hypertension and the most frequent cause, head trauma. The trepanation with two oriffices associated with a closed drainage system was the most used operating, with high efficacy and low complication rate.

Evaluating the Maturity of Data Management Practices in a Major Energy Provider Company

Data is the most important asset of a company in the information age. Other assets, such as technology, facilities or products can be copied or reverse-engineered, employees can be brought over, but data remains unique to every company. As data management topics are slowly moving from unknown unknowns to known unknowns, tools to evaluate and manage data properly are developed and refined. Many projects are in progress today to develop various maturity models for evaluating information and data management practices. These maturity models come in many shapes and sizes: from short and concise ones meant for a quick assessment, to complex ones that call for an expert assessment by experienced consultants. In this paper several of them, made not only by external inter-organizational groups and authors, but also developed internally at a Major Energy Provider Company (MEPC) are juxtaposed and thoroughly analyzed. Apart from analyzing the available maturity models related to Data Management, this paper also selects the one with the most merit and describes and analyzes using it to perform a maturity assessment in MEPC. The utility of maturity models is two-fold: descriptive and prescriptive. Besides recording the current state of Data Management practices maturity by performing the assessments, this maturity model is also used to chart the way forward. Thus, after the current situation is presented, analysis and recommendations on how to improve it based on the definitions of higher levels of maturity are given. Generally, the main trend observed was the widening of the Data Management field to include more business and “soft” areas (as opposed to technical ones) and the change of focus towards business value of data, while assuming that the underlying IT systems for managing data are “ideal”, that is, left to the purely technical disciplines to design and maintain. This trend is not only present in Data Management but in other technological areas as well, where more and more attention is given to innovative use of technology, while acknowledging that the strategic importance of IT as such is diminishing.

Survey on control and management practices of equine helminthes infection

Twenty-nine stud farms were selected in the Medium Paraíba region of the Rio de Janeiro state, Brazil. After an interview with the person responsible for the animals, faecal samples were collected from mares and analyzed via the EPG technique, faecal cultures, Sedimentation-centrifugo-flotation, and modified Ueno and Baermann techniques. The prevalence of helminths in the mares and in the stud farms was calculated. The stocking rates of pasture, change of horse bedding, absence of pasture rotation, absence of technology in the property, and less frequent treatment of the animals were associated with a greater prevalence of helminths, showing that these variables must be considered in equine control programs. The intensity of the parasitism was also associated with the stocking rate of pasture, absence of dunghill, presence of the animals only in paddocks, lack of technology in the property, less frequent treatment of the animals, and absence of the use of rotation regarding the anthelmintic class.

Essays on auditor independence

Auditor independence is a cornerstone of the auditing profession and the basic principle that underpins the reputation of the auditing profession in the public eye. Indeed, it is the attribute most demanded from auditors by the public. Therefore, the sustainability of the auditing profession depends on how auditors can protect this principle. This dissertation consists of four interrelated essays concerned with auditor independence. Specifically, it examines situations that can threaten and impair auditor independence. In addition, this dissertation also examines several variables that may enhance and protect auditor independence. The first essay aims to examine the impact of social pressures occurring within audit firms on auditors’ judgment in the setting of a society with “high power distance” and “low individualism” cultural dimensions. The social pressures consisted of obedience pressure exerted by an auditor’s superior and conformity pressure exerted by an auditor’s colleague. Moreover, two moderating variables—a multi-dimensional professional commitment and locus of control—were included as moderator variables in the relationship between the social pressures faced by auditors and their judgment. The findings show that obedience and conformity pressures influence auditor judgment. Auditors who face the social pressures will make a judgment that may be even diametrically opposite to the independence principle. The findings also indicate that a multi-dimensional professional commitment and locus of control may potentially influence auditor judgment in a situation with social pressures. The second essay aims to investigate the association of advocacy and familiarity threats caused by auditor fee dependence and auditor tenure on auditor independence based on Finnish data, law, and auditing environment. This essay was motivated by the Green Paper on Audit Policy, published by the European Commission in 2010 that questions whether the maximum fee collected from a client should be regulated and whether consecutive assignments should be limited, among others. Contrary to popular belief, this essay does not find evidence that audit fees and long auditor tenure will jeopardise auditor independence. Therefore, the findings do not support policies to regulate auditor fees or limit auditor tenure in Finland. The third essay aims to examine the effect of client intimidation on auditor independence in an audit-client conflict situation. Intimidation threat is one of five independence threats that are explicitly referenced in the IFAC’s independence framework. Client intimidation was manifested in the client threatening to replace the auditor if the auditor did not adopt the client’s position. In addition, this essay examines the role of auditor’s perceived pressure and multi-dimensions of professional commitment as moderator variables. The findings suggest that auditors who experience client intimidation in an audit conflict situation are more likely to have their independence impaired than those who are in a similar situation but without client intimidation. Moreover, auditors who experience client intimidation perceive higher pressure than those who do not experience intimidation. Finally, auditors’ affective and continuance professional commitment dimensions moderate the relationship between auditors’ perceived pressures and auditor independence. The aim of the fourth essay is twofold. First, it aims to develop a scale for measuring auditors’ reputation awareness. Second, it aims to examine the correlation between the levels of auditor reputation awareness and auditor independence. A seven-item scale was developed as the reputation awareness scale. The findings indicate that the scale consists of one dimension. It also has a level of satisfactory reliability and a high level of validity. The findings show that there is a positive correlation between the level of auditors’ reputation awareness and auditor independence.

Analysis of emergency braking performance with particular consideration of temperature effects on brakes

During vehicle deceleration due to braking there is friction between the lining surface and the brake drum or disc. In this process the kinetic energy of vehicle is turned into thermal energy that raises temperature of the components. The heating of the brake system in the course of braking is a great problem, because besides damaging the system, it may also affect the wheel and tire, which can cause accidents. In search of the best configuration that considers the true conditions of use, without passing the safety limits, models and formulations are presented with respect to the brake system, considering different braking conditions and kinds of brakes. Some modeling was analyzed using well-known methods. The flat plate model considering energy conservation was applied to a bus, using for this a computer program. The vehicle is simulated to undergo an emergency braking, considering the change of temperature on the lining-drum. The results include deceleration, braking efficiency, wheel resistance, normal reaction on the tires and the coefficient of adhesion. Some of the results were compared with dynamometer tests made by FRAS-LE and others were compared with track tests made by Mercedes-Benz. The convergence between the results and the tests is sufficient to validate the mathematical model. The computer program makes it possible to simulate the brake system performance in the vehicle. It assists the designer during the development phase and reduces track tests.

Assessment of purchasing maturity in spare parts supply chain

To describe the change of purchasing moving from administrative to strategic function academics have put forward maturity models which help practitioners to compare their purchasing activities to industry top performers and best practices. However, none of the models aim to distinguish the purchasing maturity from the after-sales point of view, even though after-sales activities are acknowledged as a relevant source of revenue, profit and competitive advantage in most manufacturing firms. The maturity of purchasing and supply management practices have a large impact to the overall performance of the spare parts supply chain and ultimately to the value creation and relationship building for the end customer. The research was done as a case study for a European after-sales organization which is part of a globally operating industrial firm specialized in heavy machinery. The study mapped the current state of the purchasing practices in the case organization and also distinguished the relevant areas for future development. The study was based on the purchasing maturity model developed by Schiele (2007) and investigated also how applicable is the maturity model in the spare parts supply chain context. Data for the assessment was gathered using five expert interviews inside the case organization and other parties involved in the company’s spare parts supply chain. Inventory management dimension was added to the original maturity model in order to better capture the important areas in a spare parts supply chain. The added five questions were deduced from the spare parts management literature and verified as relevant areas by the case organization’s personnel. Results indicate that largest need for development in the case organization are: better collaboration between sourcing and operative procurement functions, use of installed base information in the spare parts management, training plan development for new buyers, assessment of aligned KPI’s between the supply chain parties and better defining the role of after-sales sourcing. The purchasing maturity model used in this research worked well in H&R Leading, Controlling and Inventory Management dimensions. The assessment was more difficult to conduct in the Supplier related processes, Process integration and Organizational structure –dimensions, mainly because the assessment in these sections would for some parts require more company-wide assessment. Results indicate also that the purchasing maturity model developed by Schiele (2007) captures the relevant areas in the spare parts supply as well.

Use of fiber-reinforced composite framework and thermochromic pigment in maxillofacial prostheses

The purpose of this investigation was to evaluate the possibility to enhance certain qualities of facial prostheses. Polymethyl methacrylate is still being used as base mate¬rial or clip carrier material, but it is hard and heavy, and debonding of the silicone from the acrylic base material is a frequent problem. This thesis aims to evaluate the use of fiber-reinforced composite (FRC) as framework material for maxillofacial silicone prostheses. FRC has been used as reinforcement in removable and fixed partial dentures since the 1990s. This material is lightweight and can be fabricated to compress the margins of the prosthesis slightly, to keep it tightly against the skin during jaw movements and facial expressions. Additionally, the use of a thermochromic pigment, colorless in room temperature and red in a cold environment, was studied in order to evaluate the possibility of using this color changing pigment in facial prostheses to mimic the color change of facial skin in cold weather. The tensile bond strength between pre-impregnated, unidirectional FRC and maxillofacial silicone elastomer was studied. Three different bonding agents or primers were compared. Bond strength was improved by one of the primers and by roughening the surface. The effect of a skin compressing glass fiber-reinforced composite framework on facial skin blood flow was studied by using a face mask, constructed with a compression pad corresponding to the outer margin of a glass fiber-reinforced framework beam of a facial prosthesis. The skin blood flow of ten healthy volunteers, aged 23-25 years, was measured during touch, light, and moderate compression of the skin, by using laser Doppler imaging technique. None of the compressions showed any marked effects on local skin blood flow. There were no significant differences between blood flow during compression and at baseline. Maxillofacial silicone elastomer was colored intrinsically with conventional color pigments: a control group containing only conventional pigments was compared to two test groups with 0.2 wt% and 0.6 wt% thermochromic pigment added. The color of the material was measured with a spectrophotometer in room temperature and after storage in a freezer. The color stability of the maxillofacial silicone elastomer colored with thermo¬chromic pigment was evaluated by artificial aging. The color dif¬ference of the L* (lightness) and a* values (redness), comparing color after the samples were stored at room temperature and in a freezer (-19°C), was statistically significant for both 0.2 wt% and 0.6 wt% thermo¬chromic pigment groups. The differences in the b* values (yellowness) were statistically significant for the 0.6 wt% group. Exposure to ultraviolet (UV) radiation led to visually noticeable and statistically signifi¬cant color changes (ΔE) in all color values in both test groups. The specimens containing thermochromic pigment were very sensitive to UV radiation. In conclusion, a framework of fiber-reinforced composite can successfully be bonded to maxillofacial silicone elastomer, and a framework beam, compressing the facial skin, did not remarkably alter the skin blood flow on healthy, young adults. The thermochromic pigment showed color change in maxillofacial silicone elastomer. However, artificial aging showed that it was too sensitive to UV radiation to be used, as such, in maxillofacial prostheses.

Topochemistry of physical and chemical pretreatments of biomass as investigated by FE-SEM, XPS and ToF-SIMS

Surface chemistry is of great importance in plant biomass engineering and applications. The surface chemical composition of biomass which includes lignin, carbohydrates and extractives influences its interactions with chemical agents, such as pulp processing/papermaking chemicals, or enzymes for different purposes. In this thesis, the changes in the surface chemical composition of lignocellulosic biomass after physical modification for the improvement of resulting paper properties and chemical treatment for the enhancement of enzymatic hydrolysis were investigated. Low consistency (LC) refining was used as physical treatment of bleached softwood and hardwood pulp samples, and the surface chemistry of refined samples was investigated. The refined pulp was analysed as whole pulp while the fines-free fibre samples were characterized separately. The fines produced in LCrefining contributed to an enlarged surface specific area as well as the change of surface coverage by lignin and extractives, as investigated by X-ray photoelectron spectroscopy (XPS). The surface coverage by lignin of the whole pulp decreased after refining while the surface coverage by extractives increased both for pine and eucalyptus. In the case of pine, the removal of fines resulted in reduction of the surface coverage by extractives, while the surface coverage by lignin increased on fibre sample (without fines). In the case of eucalyptus, the surface coverage by lignin of fibre samples decreased after the removal of fines. In addition, the surface distribution of carbohydrates, lignin and extractives of pine and eucalyptus samples was determined by Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). LC-refining increased the amounts of pentose, hexose and extractives on the surface of pine samples. ToF-SIMS also gave clear evidence about xylan deposition and reduction of surface lignin distribution on the fibre of eucalyptus. However, the changes in the surface chemical composition during the physical treatment has led to an increase in the adsorption of fluorescent whitening agents (FWAs) on fibres due to a combination of electro-static forces, specific surface area of fibres and hydrophobic interactions. Various physicochemical pretreatments were conducted on wood and non-wood biomass for enhancing enzymatic hydrolysis of polysaccharides, and the surface chemistry of the pretreated and enzymatically hydrolysed samples was investigated by field emission scanning electron microscopy (FE-SEM), XPS and ToF-SIMS. A hydrotrope was used as a relatively novel pretreatment technology both in the case of wood and non-wood biomass. For comparison, ionic liquid and hydrothermal pretreatments were applied on softwood and hardwood as well. Thus, XPS analysis showed that the surface lignin was more efficiently removed by hydrotropic pretreatment compared to ionic liquid or hydrothermal pretreatments. SEM analysis also found that already at room temperature the ionic liquid pretreatments were more effective in swelling the fibres compared with hydrotropic pretreatment at elevated temperatures. The enzymatic hydrolysis yield of hardwood was enhanced due to the decrease in surface coverage of lignin, which was induced by hydrotropic treatment. However, hydrotropic pretreatment was not appropriate for softwood because of the predominance of guaiacyl lignin structure in this material. In addition, the reduction of surface lignin and xylan during pretreatment and subsequent increase in cellulose hydrolysis by enzyme could be observed from ToF-SIMS results. The characterisation of the non-wood biomass (e.g. sugarcane bagasse and common reed) treated by hydrotropic method, alkaline and alkaline hydrogen peroxide pretreatments were carried out by XPS and ToF-SIMS. According to the results, the action for the removal of the surface lignin of non-wood biomass by hydrotropic pretreatment was more significant compared to alkaline and alkaline hydrogen peroxide pretreatments, although a higher total amount of lignin could be removed by alkaline and alkaline hydrogen peroxide pretreatment. Furthermore, xylan could be remarkably more efficiently removed by hydrotropic method. Therefore, the glucan yield achieved from hydrotropic treated sample was higher than that from samples treated with alkaline or alkaline hydrogen peroxide. Through the use of ToF-SIMS, the distribution and localization of lignin and carbohydrates on the surface of ignocelluloses during pretreatment and enzymatic hydrolysis could be detected, and xylan degradation during enzymatic hydrolysis could also be assessed. Thus, based on the results from XPS and ToF-SIMS, the mechanism of the hydrotropic pretreatment in improving the accessibility of enzymes to fibre and further ameliorating of the enzymatic saccharification could be better elucidated.

Enabling Change in Universities: Enhancing Education for Sustainable Development with Tools for Quality Assurance

Enabling Change in Universities: Enhancing Education for Sustainable Development with Tools for Quality Assurance This thesis deals with enabling change in universities, more explicitly enhancing education for sustainable development with tools for quality assurance. Change management is a discipline within management that was developed in the 1980s because business changed from being predictable to unpredictable. The PEST mnemonic is a method to categorize factors enabling change; such as political, economic, socio-cultural and technological factors, which all affect higher education. A classification of a change, in either hard or soft, can help understanding the type of change that an organization is facing. Hard changes are more applied to problems that have clear objectives and indicators, with a known cause of the problem. Soft changes are applied to larger problems that affect the entire organization or beyond it. The basic definition for sustainable development is: the future generations should have similar opportunities as the previous. The UN has set as a global goal an integration of education for sustainable development (ESD) at all levels of education during 2005- 2014. The goal is set also in universities, the graduates of which are future leaders for all labor markets. The objective for ESD in higher education is that graduates obtain the competence to take economic, social and environmental costs and benefits into account when making decisions. Knowledge outcomes should aim for systematic and holistic thinking, which requires cross disciplinary education. So far, the development of ESD has not achieved its goals. The UN has identified a need for more transdisclipnary research in ESD. A joint global requirement for universities is quality assurance, the aim of which is to secure and improve teaching and learning. Quality, environmental and integrated management systems are used by some universities for filling the quality assurance requirements. The goal of this thesis is to open up new ways for enhancing ESD in universities, beyond the forerunners; by exploring how management systems could be used as tools for promoting ESD. The thesis is based on five studies. In the first study, I focus on if and how tools for quality assurance could be benefitted for promoting ESD. It is written from a new perspective, the memetic, for reaching a diversity of faculty. A meme is an idea that diffuses from brain to brain. It can be applied for cultural evolution. It is a theory that is based on the evolutionary theory by Darwin, applied for social sciences. In the second Paper, I present the results from the development of the pilot process model for enhancing ESD with management systems. The development of the model is based on a study that includes earlier studies, a survey in academia and an analysis of the practice in 11 universities in the Nordic countries. In the third study, I explore if the change depends on national culture or if it is global. It is a comparative study on both policy and implementation level, between the Nordic countries and China. The fourth study is a single case study based on change management. In this study, I identify what to consider in order to enable the change: enhancing ESD with tools for quality assurance in universities. In the fifth Paper, I present the results of the process model for enhancing ESD with management systems. The model was compared with identified drivers and barriers for enhancing ESD and for implementing management systems. Finally, the process model was piloted and applied for identifying sustainability aspects in curricula. Action research was chosen as methodology because there are not already implemented approaches using quality management for promoting ESD, why the only way to study this is to make it happen. Another reason for choosing action research is since it is essential to involve students and faculty for enhancing ESD. Action based research consists of the following phases: a) diagnosing, b) planning action, c) taking action and d) evaluating action. This research was made possible by a project called Education for Sustainable Development in Academia in the Nordic countries, ESDAN, in which activities were divided into these four phases. Each phase ended with an open seminar, where the results of the study were presented. The objective for the research project was to develop a process for including knowledge in sustainable development in curricula, which could be used in the quality assurance work. Eleven universities from the Nordic countries cooperated in the project. The aim was, by applying the process, to identify and publish examples of relevant sustainability aspects in different degree programs in universities in the Nordic countries. The project was partly financed by the Nordic Council of Ministers and partly by the participating pilot universities. Based on the results of my studies, I consider that quality, environmental and integrated management systems can be used for promoting ESD in universities. Relevant sustainability aspects have been identified in different fields of studies by applying the final process model. The final process model was compared with drivers and barriers for enhancing ESD and for implementing management systems in universities and with succeeding with management systems in industry. It corresponds with these, meaning that drivers are taken into account and barriers tackled. Both ESD and management systems in universities could be considered successful memes, which can reflect an effective way of communication among individuals. I have identified that management systems could be used as tools for hard changes and to support the soft change of enhancing ESD in universities with management system. Based on the change management study I have summarized recommendations on what to consider in order to enable the studied change. The main practical implications of the results are that the process model could be applied for assessment, benchmarking and communication of ESD, connected to quality assurance, when applied. This is possible because the information can be assembled in one picture, which facilitates comparison. The memetic approach can be applied for structuring. It is viable to make comparative studies between cultures, for getting insight in special characteristics of the own culture. Action based research is suitable for involving faculty. Change management can be applied for planning a change, which both enhancing ESD and developing management systems are identified to be.

Primary and secondary development of Cyperus giganteus Vahl rhizome (Cyperaceae)

In Cyperus giganteus, like in other Monocotyledoneae, the protoderm, procambium, fundamental meristem and primary thickening meristem (PTM) are differentiated from the rhizome promeristem. The PTM produces the inner cortical parenchyma, endodermis, pericycle and amphivasal vascular bundles, which are formed by the procambium too. After the primary body differentiates, cellular divisions continue only in the pericycle, and originate an irregular vascular system with vessel elements shorter and more branched than those found in the primary growth. This change of activity in the pericycle defines a secondary growth, where the secondary thickening meristem (STM) is the pericycle itself.

Sustainable Gold Mining- Life Cycle Assessment of Cyanidation and Thiosulphate Leaching

With the increasing concern of the sustainable approach of gold mining, thiosulphate has been researched as an alternative lixiviant to cyanide since cyanide is toxic to the environment. In order to investigate the possibility of thiosulphate leaching application in the coming future, life cycle assessment, is conducted to compare the environmental footprint of cyanidation and thiosulphate leaching. The result showed the most significant environmental impact of cyanidation is toxicity to human, while the ammonia of thiosulphate leaching is also a major concern of acidification. In addition, an ecosystem evaluation is also performed to indicate the potential damages caused by an example of cyanide spill at Kittilä mine, resulting in significant environmental risk cost that has to be taken into account for decision making. From the opinion collected from an online LinkedIn discussion forum, the anxiety of sustainability alone would not be enough to contribute a significant change of conventional cyanidation, until the tighten policy of cyanide use. International Cyanide Code, therefore, is crucial for safe gold production. Nevertheless, it is still thoughtful to consider the values of healthy ecosystem and the gold for long-term benefit.

Spreading depression is facilitated in adult rats previously submitted to short episodes of malnutrition during the lactation period

Lactating rat dams were submitted to short episodes (1, 2 or 3 weeks) of nutritional restriction by receiving the "regional basic diet" (RBD, with 8% protein) of low-income human populations of Northeast Brazil. Their pups were then studied regarding the developmental effects on body and brain weights. When the rats reached adulthood, cortical susceptibility to the phenomenon of spreading depression (SD) was evaluated by performing electrophysiological recordings on the surface of the cerebral cortex. SD was elicited at 20-min intervals by applying 2% KCl for 1 min to a site on the frontal cortex and its occurrence was monitored at 2 sites in the parietal region by recording the electrocorticogram and the slow potential change of SD. When compared to control rats fed a commercial diet with 23% protein, early malnourished rats showed deficits in body and brain weights (10% to 60% and 3% to 15%, respectively), as well as increases in velocity of SD propagation (10% to 20%). These effects were directly related to the duration of maternal dietary restriction, with pups malnourished for 2 or 3 weeks presenting more intense weight and SD changes than those malnourished for 1 week. The effects of 1-week restrictions on SD were less evident in the pups malnourished during the second week of lactation and were more evident in pups receiving the RBD during the third week. The results indicate that short episodes of early malnutrition during the suckling period can affect body and brain development, as well as the cortical susceptibility to SD during adulthood. The data also suggest that the third week of lactation is the period during which the brain is most sensitive to malnutrition, concerning the effects on SD

Sexual behavior and fertility of male rats submitted to prolonged immobilization-induced stress

In order to investigate whether prolonged stress interferes with the onset of sexual behavior at puberty and with fertility at adulthood, prepubertal male Wistar rats (40 days of age) were immobilized 6 h a day for 15 days (up to early puberty) or for 60 days (until sexual maturity). Pubertal stressed rats showed a two-fold increase in the latency for the first mount (probably due to repeated aversive experience in which a change of environment was always followed by immobilization) and a 2.5-fold increase in the frequency of thrusting (indicative of enhanced sexual performance). The apparently stimulatory effect of prolonged stress on the onset of sexual behavior is discussed in terms of increased testosterone level and interference with the complex interchanges between the neurotransmitters/neuropeptides involved in the central control of male sexual activity. Adult stressed animals were mated with normal females, which became pregnant but exhibited a more than two-fold increase in both pre-implantation and post-implantation loss, probably due to a smaller rate of fertilization and/or fertilization with damaged spermatozoa.

Head-to-head comparison of dipyridamole, dobutamine and pacing stress echocardiography for the detection of myocardial ischemia in an animal model of coronary artery stenosis

To compare the sensitivity of dipyridamole, dobutamine and pacing stress echocardiography for the detection of myocardial ischemia we produced a physiologically significant stenosis in the left circumflex artery of 14 open-chest dogs (range: 50 to 89% reduction in luminal diameter). In each study, dobutamine (5 to 40 µg kg-1 min-1 in 3-min stages) and pacing (20 bpm increments, each 2 min, up to 260 bpm) were performed randomly, and then followed by dipyridamole (up to 0.84 mg/kg over 10 min). The positivity of stress echocardiography tests was quantitatively determined by a significant (P<0.05) reduction of or failure to increase absolute and percent systolic wall thickening in the stenotic artery supplied wall, as compared to the opposite wall (areas related to the left anterior descending artery). Systolic and diastolic frozen images were analyzed off-line by two blinded observers in the control and stress conditions. The results showed that 1) the sensitivity of dobutamine, dipyridamole and pacing stress tests was 57, 57 and 36%, respectively; 2) in animals with positive tests, the mean percent change of wall thickening in left ventricular ischemic segments was larger in the pacing (-19 ± 11%) and dipyridamole (-18 ± 16%) tests as compared to dobutamine (-9 ± 6%) (P = 0.05), but a similar mean reduction of wall thickening was observed when this variable was normalized to a control left ventricular segment (area related to the left anterior descending artery) (pacing: -16 ± 7%; dipyridamole: -25 ± 16%; dobutamine: -26 ± 10%; not significant), and 3) a significant correlation was observed between magnitude of coronary stenosis and left ventricular segmental dysfunction induced by ischemia in dogs submitted to positive stress tests. We conclude that the dobutamine and dipyridamole stress tests showed identical sensitivities for the detection of myocardial ischemia in this one-vessel disease animal model with a wide range of left circumflex artery stenosis. The pacing stress test was less sensitive, but the difference was not statistically significant. The magnitude of segmental left ventricular dysfunction induced by ischemia was similar in all stress tests evaluated.