Design of polymeric stabilizers for size-controlled synthesis of monodisperse gold nanoparticles in water

A new methodology is described for the one-step aqueous preparation of highly monodisperse gold nanoparticles with diameters below 5 nm using thioether- and thiol-functionalized polymer ligands. The particle size and size distribution was controlled by subtle variation of the polymer structure. It was shown that poly(acrylic acid) (PAA) and poly(methacrylic acid) (PMAA) were the most effective stabilizing polymers in the group studied and that relatively low molar mass ligands (similar to 2500 g/mol) gave rise to the narrowest particle size distributions. Particle uniformity and colloidal stability to changes in ionic strength and pH were strongly affected by the hydrophobicity of the ligand end group. "Multidentate" thiol-terminated ligands were produced by employing dithiols and tetrathiols as chain-transfer agents, and these ligands gave rise to particles with unprecedented control over particle size and enhanced colloidal stability. It was found throughout that dynamic light scattering (DLS) is a very useful corroboratory technique for characterization of these gold nanoparticles in addition to optical spectroscopy and TEM.

Morphology-controllable synthesis and characterization of single-crystal molybdenum trioxide

Molybdenum trioxide nanobelts and prism-like particles with good crystallinity and high surface areas have been prepared by a facile hydrothermal method, and the morphology could be controlled by using different inorganic salts, such as KNO3, Ca(NO3)(2), La(NO3)(3), etc. The possible growth mechanism of molybdenum trioxide prism-like particles is discussed on the basis of the presence of HI and the modification of metal cations. The as-prepared nanomaterials are characterized by means of powder X-ray diffraction (PXRD), field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), Fourier transformation infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), and ultraviolet and visible spectroscopy (UV-vis). TEM and HRTEM micrographs show that the molybdenum trioxide nanobelts and prism-like particles have a relatively high degree of crystallinity and uniformity. BET specific surface areas of the as-prepared molybdenum trioxide nanocrystals are 67-79 m(2)g(-1). XPS analysis indicates that the hexavalent molybdenum is predominant in the nanocrystals. UV-vis spectra reveal that the direct band gap energy of the annealed molybdenum trioxide prism-like particles shows a pronounced blue shift compared to that of bulk MoO3 powder.

Facile sonochemical synthesis of CePO4 : Tb/LaPO4 core/shell nanorods with highly improved photoluminescent properties

A simple, efficient and quick method has been established for the synthesis of CePO4:Tb nanorods and CePO4:Tb/LaPO4 core/shell nanorods via ultrasound irradiation of inorganic salt aqueous solution under ambient conditions for 2 h. The as-prepared products were characterized by means of powder x-ray diffraction (PXRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction ( SAED), x-ray photoelectron spectroscopy (XPS), photoluminescence (PL) spectra and lifetimes. TEM micrographs show that all of the as-prepared cerium phosphate products have rod-like shape, and have a relatively high degree of crystallinity and uniformity. HRTEM micrographs and SAED results prove that these nanorods are single crystalline in nature. The emission intensity and lifetime of the CePO4:Tb/LaPO4 core/shell nanorods increased significantly with respect to those of CePO4: Tb core nanorods under the same conditions. A substantial reduction in reaction time as well as reaction temperature is observed compared with the hydrothermal process.

Assembly of multilayer films containing iron(III)- substituted Dawson-type heteropolyanions and its electrocatalytic properties: cyclic voltammetry, electrochemical impedance spectroscopy and UV-Vis spectrometry

Ultrathin multilayer films have been prepared by means of alternate adsorption of iron(Ill)-substituted heteropolytungstate anions and a cationic redox polymer on the 4-aminobenzoic acid modified glassy carbon electrode surface based on electrostatic layer-by-layer assembly. Cyclic voltammetry, electrochemical impedance spectroscopy and UV-Vis absorption spectrometry have been used to easily monitor the uniformity of thus-formed multilayer films. Especially, the electrochemical impedance spectroscopy is successfully used to monitor the multilayer deposition processes and is a very useful technique in the characterization of multilayer films because it provides valuable information about the interfacial impedance features. All these results reveal regular film growth with each layer adsorption. The resulting multilayer films can effectively catalyze the reduction of H2O2,NO2- and BrO3-.

Multilayer assemblies consisting of tri-vanadium-substituted heteropolyanions and its electrocatalytic properties

We describe the controlled fabrication of ultrathin multilayer films consisting of tri-vanadium- substituted heteropolytungstate anions (denoted as P2W15V3) and a cationic polymer of quaternized poly (4-vinylpyridine) partially complexed with osmium bis(2,2'-bipyridine) (denoted as QPVP-Os) on the 4-aminobenzoic acid (4-ABA) modified glassy carbon electrode (GCE) surface based on layer-by-layer assembly. Cyclic voltammetry and UV-vis absorption spectrometry have been used to easily monitor the thickness and uniformity of thus-formed multilayer films. The V-centered redox reaction of P2W15V3 in the multilayer films can effectively catalyze the reduction of BrO3- and NO2-. The resulting P2W15V3/QPVP-Os multilayer film modified electrode behaves as a much promising electrochemical sensor because of the low overpotential for the catalytic reduction of BrO3- and NO2-, and the catalytic oxidation of ascorbic acid.

Biodegradable electrospun fibers for drug delivery

The influences of surfactants and medical drugs on the diameter size and uniformity of electrospun poly(L-lactic acid) (PLLA) fibers were examined by adding various surfactants (cationic, anionic, and nonionic) and typical drugs into the PLLA solution. Significant diameter reduction and uniformity improvement were observed. It was shown that the drugs were capsulated inside of the fibers and the drug release in the presence of proteinase K followed nearly zero-order kinetics due to the degradation of the PLLA fibers. Such ultrafine fiber mats containing drugs may find clinical applications in the future.

The fabrication of dipped CdS and sputtered ITO thin films for photovoltaic solar cells

Stable bilayer thin films of indium tin oxide (ITO) on CdS and CdS on ITO were formed for the window material of solar cells by chemical bath and sputtering methods. Scanning electron microscopy and X-ray diffraction studies have shown that both the ITO and CdS films are continuous, homogeneous, with high compactness. Measurement of the CdS film thickness across the 2 x 4 cm(2) reveals the good uniformity of these films. Four-point probe measurements show that the resistivity of a CdS film on an ITO surface is much better than that of the single CdS film The thermal stability of an ITO/CdS bilayer, interfacial reaction and optical transmittance were investigated at different annealing temperatures and environments (air, vacuum and N-2 + H-2). The results showed that the ITO/CdS bilayer film is a good window material for the CuInSe2 and CdTe cells. It is a simple method using a small amount of the cadmium compound.

Phylogeography of Pinus tabulaeformis Carr. (Pinaceae), a dominant species of coniferous forest in northern China

How coniferous trees in northern China changed their distribution ranges in response to Quaternary climatic oscillations remains largely unknown. Here we report a study of the phylogeography of Pinus tabulaeformis, an endemic and dominant species of coniferous forest in northern China. We examined sequence variation of maternally inherited, seed-dispersed mitochondrial DNA (mtDNA) (nad5 intron 1 and nad4/3-4) and paternally inherited, pollen- and seed-dispersed chloroplast DNA (cpDNA) (rpl16 and trnS-trnG) within and among 30 natural populations across the entire range of the species. Six mitotypes and five chlorotypes were recovered among 291 trees surveyed. Population divergence was high for mtDNA variation (G(ST) = 0.738, N-ST = 0.771) indicating low levels of seed-based gene flow and significant phylogeographical structure (N-ST > G(ST), P < 0.05). The spatial distribution of mitotypes suggests that five distinct population groups exist in the species: one in the west comprising seven populations, a second with a north-central distribution comprising 15 populations, a third with a southern and easterly distribution comprising five populations, a fourth comprising one central and one western population, and a fifth comprising a single population located in the north-central part of the species' range. Each group apart from the fourth group is characterized by a distinct mitotype, with other mitotypes, if present, occurring at low frequency. It is suggested, therefore, that most members of each group apart from Group 4 are derived from ancestors that occupied different isolated refugia in a previous period of range fragmentation of the species, possibly at the time of the Last Glacial Maximum. Possible locations for these refugia are suggested. A comparison of mitotype diversity between northern and southern subgroups within the north-central group of populations (Group 2) showed much greater uniformity in the northern part of the range both within and between populations. This could indicate a northward migration of the species from a southern refugium in this region during the postglacial period, although alternative explanations cannot be ruled out. Two chlorotypes were distributed across the geographical range of the species, resulting in lower levels of among-population chlorotype variation. The geographical pattern of variation for all five chlorotypes provided some indication of the species surviving past glaciations in more than one refugium, although differentiation was much less marked, presumably due to the greater dispersal of cpDNA via pollen.

Infrared heater arrays for warming ecosystem field plots

There is a need for methodology to warm open-field plots in order to study the likely effects of global warming on ecosystems in the future. Herein, we describe the development of arrays of more powerful and efficient infrared heaters with ceramic heating elements. By tilting the heaters at 45 degrees from horizontal and combining six of them in a hexagonal array, good uniformity of warming was achieved across 3-m-diameter plots. Moreover, there do not appear to be obstacles (other than financial) to scaling to larger plots. The efficiency [eta(h) (%); thermal radiation out per electrical energy in] of these heaters was higher than that of the heaters used in most previous infrared heater experiments and can be described by: eta(h) = 10 + 25exp(-0.17 u), where u is wind speed at 2 m height (m s(-1)). Graphs are presented to estimate operating costs from degrees of warming, two types of plant canopy, and site windiness. Four such arrays were deployed over plots of grass at Haibei, Qinghai, China and another at Cheyenne, Wyoming, USA, along with corresponding reference plots with dummy heaters. Proportional integral derivative systems with infrared thermometers to sense canopy temperatures of the heated and reference plots were used to control the heater outputs. Over month-long periods at both sites, about 75% of canopy temperature observations were within 0.5 degrees C of the set-point temperature differences between heated and reference plots. Electrical power consumption per 3-m-diameter plot averaged 58 and 80 kW h day(-1) for Haibei and Cheyenne, respectively. However, the desired temperature differences were set lower at Haibei (1.2 degrees C daytime, 1.7 degrees C night) than Cheyenne (1.5 degrees C daytime, 3.0 degrees C night), and Cheyenne is a windier site. Thus, we conclude that these hexagonal arrays of ceramic infrared heaters can be a successful temperature free-air-controlled enhancement (T-FACE) system for warming ecosystem field plots.

基于模拟退火算法的挤出模参数优化

建立了塑料熔体在异型材挤出机头流道中的流动均匀性模型 ,阐明了模具结构参数与流动均匀性间的关系,确定了塑料挤出模优化设计的目标函数和设计变量 ,并将一种改进的模拟退火算法用于流线型塑料异型材挤出机头的优化设计。实例表明所用方法对挤出模优化设计的适用性,该方法在利用经验的同时 ,优化了模具结构参数 ,提高了模具设计的智能化

基于LBL声信标的AUV快速精确定位

长基线声学定位系统是水下机器人广泛应用的外部导航设备。以对"CR-02"6000m自治水下机器人(简称AUV)技术的深入开发为背景,提出在原有长基线(LBL)定位系统的基础上增加导航功能的方案。由于海水介质非均匀性与复杂的时空变化特性,给基于测距的位置计算带来很大困难。采用平均声速法计算耗时小而误差大,波阵面定位法误差小而耗时大。为解决这个矛盾,根据AUV深度传感器给出的深度信息,采用本征声线快速计算方法解算AUV的水平面位置。与波阵面法、平均声速法进行了综合比较。仿真实验表明该方法具有优良的性能,满足AUV导航需要。

激光拼焊错边产生与预测建模方法

错边是评定激光拼焊质量的一个非常重要的指标,薄板构件错边的控制是激光拼焊中一个难题。针对国内首条全自动激光拼焊设备,对错边的产生以及控制方法进行了深入研究,经过大量试验确定了影响错边大小的几个主要因素,板材自身物理变形、压紧力大小与均匀性、压紧横梁变形、支撑底板平面度误差以及焊接变形的影响。通过分析以上因素对错边的影响以及各个因素之间相互关系,建立了错边预测的数学模型。试验验证了模型的正确性,从而为确定错边产生原因,提高焊接质量提供了一个有效的理论指导。

徐家围子断陷连片叠前时间偏移处理方法研究

In this paper, the detailed analysis of fundamental seismic data and theoretical method are given, and the tests of some new technologies are performed. For seismic data processing assembly, some key technologies are developed and applied, such as global static correction, amplitude consistency processing, wavelet consistency shaping, fine velocity model establishing and prestack time migration. These technologies can efficiently settle the problems during the course of multiple- block– jointed prestack time migration processing, and it is highly significant for holding the oil output of 40,000,000 tons for Daqing oilfield. Through the research of this dissertation, the following important contributions are shown: (1) The combination of near-surface model method and refraction static correction method is developed, and is applied to solve global static correction for the whole merging area. (2) Prestack amplitude normalization processing method based on fold is developed. The method eliminates the effects of fold on amplitude uniformity, and solves the problem of energy uniformity for tie-area prestack migration processing. (3) Wavelet consistency is investigated. For multiple survey blocks existing in the area, the optimum method of wavelet shaping is developed, which removes the waveform variance between two adjacent blocks. (4) Controlled velocity inversion (CVI) technique is used to establish migration velocity field. It can largely shorten the period of velocity modeling, and improve velocity analysis precision. (5) Float datum level technique is employed, and is able to guarantee prestack migration results of subsurface shallow layers. (6) The static partition of seismic data volume relating to migration aperture is firstly developed. And the precious imaging for huge data volume by prestack time migration is realized. (7) The numerical forward simulation and prestack migration processing is primarily combined to discuss the migration technique for a complex geology structure from practical field information. The combination of numerical simulation and prestack migration is a feasible way to solve the fine imaging of complex volcanic structure. And the combination approach can help to select appropriate migration parameters.

电离层胶片频高图数字化转换与分析研究

The ionogram acquired with the ionospheric vertical sounding method is the oldest data in the history of ionospheric research. Using of modern microelectronics and computer technology to digitalize, analyse and preserve the huge amount of historical film ionogram has become more and more important and urgent. This paper introduced the progress of the film ionogram digitalization by using digital image processing technologies to correct and repair film ionogram and convert them in an exchangeable format. An analysis and conversion software, basing on this method, has been developed for the film ionogram analysis, and then it introduces the application of this software by combining the SAO Explorer program for Wuhan film ionogram and pseudo-color ionogram in Yamagawa in Japan. It shows that our method is reliable，and the developed software is used friendly and provides a positive solution in digitalization and analysis of huge amount of historical film ionogram. Firstly, we briefly introduce the film ionogram and the process of its digitalization. By observing a amount of film ionogram, we obtain some common characteristics of the digitalized film ionogram following as: (1) the image rotation are caused by scanning; (2) the vertical axis of a large number of film ionogram exist more or less tilt and bending ; (3) coordinates of the film ionogram appear the non-uniformity phenomena result from the instability of driving motor rotation and the error of altitudinal cursor orientation. Moreover, based on the characteristics of the film ionogram and the SAO Explorer software which is widely used for the digital ionogram analysis in the world, a new method has been developed for film ionogram procession. The method contains the image geometric correction and film ionogram format conversion. The image geometric correction includes such as image rotation correction, vertical correction and coordinates scale correction. After geometric correction, the BMP file format images will be converted to the SBF file format images. Then, we also discuss the data format converting methods, which include two methods of the image data mapping basing on the normalization and logarithm, and the method of the preprocessing of the noise filtering and the threshold setting. Combining with SAO Explorer software, we successfully obtain ionospheric parameters and electron profile from the converted SBF file format digital ionograms. Based on the above method, we developed the software for the film ionogram to realize its correction analysis and conversion of the image format, and then give a introduction for its function and operation. Subsequently, the software are applied into the Wuhan film ionogram which separately observed in the high solar activity year and the low in 1980s last century. The results reveal the converted SBF digital ionogram almost preserve the all echo information of the film ionogram. Furthermore, we expressly discuss the application to the Wuhan film ionogram in 1958 in order to validate the applicability and credibility of the software. And it is showed that the important information of the film ionogram are maintained into the SBF digital ionogram. It is represented that there is credibility for conversion of the software when it applied in the older film ionogram. In sum, this software could apply to the digitalization and analysis of huge amount of historical film ionogram. Last, we extended the function of the software by bring some new conversion method and used it to apply to the pseudo-color ionogram of yamagawa in Japan. The results show that the converted ionogram information basically maintain the importantly ionogram information and the error of scaling of converted SBF file format image is almost acceptable, though there is no preprocessing for the original ionogram. Hence, we could extend the applicable range of the software and apply it to all kinds of simulative ionogram imaging by improving the method and software.