Constant wall heat flux boundary conditions in micro-channels filled with porous material with internal heat generation under local thermal non-equilibrium conditions

Forced convection heat transfer in a micro-channel filled with a porous material saturated with rarefied gas with internal heat generation is studied analytically in this work. The study is performed by analysing the boundary conditions for constant wall heat flux under local thermal non-equilibrium (LTNE) conditions. Invoking the velocity slip and temperature jump, the thermal behaviour of the porous-fluid system is studied by considering thermally and hydrodynamically fully-developed conditions. The flow inside the porous material is modelled by the Darcy–Brinkman equation. Exact solutions are obtained for both the fluid and solid temperature distributions for two primary approaches models A and B using constant wall heat flux boundary conditions. The temperature distributions and Nusselt numbers for models A and B are compared, and the limiting cases resulting in the convergence or divergence of the two models are also discussed. The effects of pertinent parameters such as fluid to solid effective thermal conductivity ratio, Biot number, Darcy number, velocity slip and temperature jump coefficients, and fluid and solid internal heat generations are also discussed. The results indicate that the Nusselt number decreases with the increase of thermal conductivity ratio for both models. This contrasts results from previous studies which for model A reported that the Nusselt number increases with the increase of thermal conductivity ratio. The Biot number and thermal conductivity ratio are found to have substantial effects on the role of temperature jump coefficient in controlling the Nusselt number for models A and B. The Nusselt numbers calculated using model A change drastically with the variation of solid internal heat generation. In contrast, the Nusselt numbers obtained for model B show a weak dependency on the variation of internal heat generation. The velocity slip coefficient has no noticeable effect on the Nusselt numbers for both models. The difference between the Nusselt numbers calculated using the two models decreases with an increase of the temperature jump coefficient.

Catalytic Processes Mediated by Metal−Organic Frameworks : Reactivity and Mechanistic Studies

The present thesis describes the development of heterogeneous catalytic methodologies using metal−organic frameworks (MOFs) as porous matrices for supporting transition metal catalysts. A wide spectrum of chemical reactions is covered. Following the introductory section (Chapter 1), the results are divided between one descriptive part (Chapter 2) and four experimental parts (Chapters 3–6). Chapter 2 provides a detailed account of MOFs and their role in heterogeneous catalysis. Specific synthesis methods and characterization techniques that may be unfamiliar to organic chemists are illustrated based on examples from this work. Pd-catalyzed heterogeneous C−C coupling and C−H functionalization reactions are studied in Chapter 3, with focus on their practical utility. A vast functional group tolerance is reported, allowing access to substrates of relevance for the pharmaceutical industry. Issues concerning the recyclability of MOF-supported catalysts, leaching and operation under continuous flow are discussed in detail. The following chapter explores puzzling questions regarding the nature of the catalytically active species and the pathways of deactivation for Pd@MOF catalysts. These questions are addressed through detailed mechanistic investigations which include in situ XRD and XAS data acquisition. For this purpose a custom reaction cell is also described in Chapter 4. The scope of Pd@MOF-catalyzed reactions is expanded in Chapter 5. A strategy for boosting the thermal and chemical robustness of MOF crystals is presented. Pd@MOF catalysts are coated with a protecting SiO2 layer, which improves their mechanical properties without impeding diffusion. The resulting nanocomposite is better suited to withstand the harsh conditions of aerobic oxidation reactions. In this chapter, the influence of the nanoparticles’ geometry over the catalyst’s selectivity is also investigated. While Chapters 3–5 dealt with Pd-catalyzed processes, Chapter 6 introduces hybrid materials based on first-row transition metals. Their reactivity is explored towards light-driven water splitting. The heterogenization process leads to stabilized active sites, facilitating the spectroscopic probing of intermediates in the catalytic cycle.

The Effect of Residence Time on the Tensile Properties of Superelastic and Thermal Activated Ni-Ti Orthodontic Wires

Since the 1980s, different devices based on superelastic alloys have been developed to fulfill orthodontic applications. Particularly in the last decades several researches have been carried out to evaluate the mechanical behavior of Ni-Ti alloys, including their tensile, torsion and fatigue properties. However, studies regarding the dependence of elastic properties on residence time of Ni-Ti wires in the oral cavity are scarce. Such approach is essential since metallic alloys are submitted to mechanical stresses during orthodontic treatment as well as pH and temperature fluctuations. The goal of the present contribution is to provide elastic stress-strain results to guide the orthodontic choice between martensitic thermal activated and austenitic superelastic Ni-Ti alloys. From the point of view of an orthodontist, the selection of appropriate materials and the correct maintenance of the orthodontic apparatus are essential needs during clinical treatment. The present work evaluated the elastic behavior of Ni-Ti alloy wires with diameters varying from 0.014 to 0.020 inches, submitted to hysteresis tensile tests with 8% strain. Tensile tests were performed after periods of use of 1, 2 and 3 months in the oral cavity of patients submitted to orthodontic treatment. The results from the hysteresis tests allowed to exam the strain range covered by isostress lines upon loading and unloading, as well as the residual strain after unloading for both superelastic and thermal activated Ni-Ti wires. Superelastic Ni-Ti wires exhibited higher load isostress values compared to thermal activated wires. It was found that such differences in the load isostress values can increase with increasing residence time.

The impacts of environmental and anthropogenic stressors on largemouth bass: an integration of field and laboratory studies

Several environmental stressors can impact the physiology and survival of fishes. Fish experience natural fluctuations in temperature and dissolved oxygen, but variations in these parameters due to anthropogenic sources are typically greater in magnitude and duration. Changes in temperature and oxygen of anthropogenic origins may therefore have larger negative impacts on fish than those occurring during natural events. Physiological parameters are sensitive indicators of the impacts of stressors by providing insight into the manner in which fish are disturbed by the stressor. Fish may display cumulative physiological responses to successive stressors, but the concept of synergy among multiple thermal stressors is poorly understood. Further, some fish species can be subjected to competitive angling events, which expose fish to an array of additional stressors that can increase mortality. The impacts of these events may change over seasons as fish display seasonal changes in behavior and physiology. Latitudinal origin may also affect the physiological response and mortality of fish exposed to common environmental stressors as individual populations are adapted to local environmental conditions. This thesis focuses on addressing these potential impacts on physiological parameters and mortality of largemouth bass (Micropterus salmoides) and provides implications for management and conservation. Largemouth bass were relatively robust to abrupt changes in temperature and oxygen, but were perturbed from physiological homeostasis during large (12°C) temperature shocks and low (< 4 mg O2/L) levels of dissolved oxygen. Cumulative physiological impacts of multiple cold shocks were only slightly greater than the disturbances sustained during a single cold shock, suggesting largemouth bass are able to tolerate successive thermal stressors. Largemouth bass exhibited seasonal changes in physiological parameters but the responses of fish to angling tournaments were relatively similar across seasons when compared with seasonal controls. Mortality was low during angling tournaments held during four seasons and no apparent seasonal trends were observed. Lastly, largemouth bass from two latitudinally separated populations exhibited differences in their physiological responses to acute cold stressors and overwinter mortality, characterized by greater mortality and physiological disturbances of southern fish than northern fish. Knowledge gained from this study can be used to make management and conservation decisions regarding a host of environmental factors and provides insight into the mechanisms by which fish species can persist over large latitudinal ranges.

The Effect of Residence Time on the Tensile Properties of Superelastic and Thermal Activated Ni-Ti Orthodontic Wires

Since the 1980s, different devices based on superelastic alloys have been developed to fulfill orthodontic applications. Particularly in the last decades several researches have been carried out to evaluate the mechanical behavior of Ni-Ti alloys, including their tensile, torsion and fatigue properties. However, studies regarding the dependence of elastic properties on residence time of Ni-Ti wires in the oral cavity are scarce. Such approach is essential since metallic alloys are submitted to mechanical stresses during orthodontic treatment as well as pH and temperature fluctuations. The goal of the present contribution is to provide elastic stress-strain results to guide the orthodontic choice between martensitic thermal activated and austenitic superelastic Ni-Ti alloys. From the point of view of an orthodontist, the selection of appropriate materials and the correct maintenance of the orthodontic apparatus are essential needs during clinical treatment. The present work evaluated the elastic behavior of Ni-Ti alloy wires with diameters varying from 0.014 to 0.020 inches, submitted to hysteresis tensile tests with 8% strain. Tensile tests were performed after periods of use of 1, 2 and 3 months in the oral cavity of patients submitted to orthodontic treatment. The results from the hysteresis tests allowed to exam the strain range covered by isostress lines upon loading and unloading, as well as the residual strain after unloading for both superelastic and thermal activated Ni-Ti wires. Superelastic Ni-Ti wires exhibited higher load isostress values compared to thermal activated wires. It was found that such differences in the load isostress values can increase with increasing residence time.

Thermal activation, long-range ordering, and topological frustration of artificial spin ice

Frustrated systems, typically characterized by competing interactions that cannot all be simultaneously satisfied, are ubiquitous in nature and display many rich phenomena and novel physics. Artificial spin ices (ASIs), arrays of lithographically patterned Ising-like single-domain magnetic nanostructures, are highly tunable systems that have proven to be a novel method for studying the effects of frustration and associated properties. The strength and nature of the frustrated interactions between individual magnets are readily tuned by design and the exact microstate of the system can be determined by a variety of characterization techniques. Recently, thermal activation of ASI systems has been demonstrated, introducing the spontaneous reversal of individual magnets and allowing for new explorations of novel phase transitions and phenomena using these systems. In this work, we introduce a new, robust material with favorable magnetic properties for studying thermally active ASI and use it to investigate a variety of ASI geometries. We reproduce previously reported perfect ground-state ordering in the square geometry and present studies of the kagome lattice showing the highest yet degree of ordering observed in this fully frustrated system. We consider theoretical predictions of long-range order in ASI and use both our experimental studies and kinetic Monte Carlo simulations to evaluate these predictions. Next, we introduce controlled topological defects into our square ASI samples and observe a new, extended frustration effect of the system. When we introduce a dislocation into the lattice, we still see large domains of ground-state order, but, in every sample, a domain wall containing higher energy spin arrangements originates from the dislocation, resolving a discontinuity in the ground-state order parameter. Locally, the magnets are unfrustrated, but frustration of the lattice persists due to its topology. We demonstrate the first direct imaging of spin configurations resulting from topological frustration in any system and make predictions on how dislocations could affect properties in numerous materials systems.

Studies on the synthesis of novel PP2A inhibitors and a GPCR detergent

Chapter 1 While targeting kinases in oncology research has been explored extensively, targeting protein phosphatases is currently in its infancy. However, a number of pharmaceutical companies are currently looking to expand their research efforts in this area. PP2A has been shown to down-regulate ERK5, a mitogen-activated protein kinase (MAPK) that has been shown to be important in driving the invasive phenotype of prostate cancer. Fostriecin and its related structural analogues PD 113,270 and 113,271 have been shown to inhibit a mitotic entry checkpoint in cell growth through the potent and selective inhibition of protein phosphatases PP1, PP2A, and PP4 (IC50 of 45 μM, 1.5 nM, and 3 nM respectively). Fostriecin is one of the most selective protein phosphatase inhibitors disclosed to date with a 104 fold selectivity for PP2A/PP4 versus PP1. Unfortunately, fostriecin and its analogues are very unstable, and this instability has effectively prevented them from being used as effective therapeutic leads. The microcystins and nodularins on the other hand, exhibit significant inhibitory activity against PP1 and PP2A (IC50 = 26 pM and 1.8 nM respectively), but their high toxicity has prevented any therapeutic application. Truncation of the ADDA chain from these polypeptides completely attenuates PP inhibitory activity. Simpler analogues incorporating the N-acylated ADDA chain and D-Ala retain moderate activity against PP1 and PP2A (IC50 = 1.0 μM and 0.17 μM respectively). The generation of a new series of fostriecin analogues to further expand its structure-activity relationship is envisaged with a view to creating new more stable PP2A inhibitors. It was hoped that by incorporating some of the more stable structural features of ADDA into fostriecin that stability and activity could be reconciled. With that in mind a series of PP2A inhibitors were synthesised and biologically evaluated. Chapter 2 GPCRs are an important area of research and are the targets of a quarter of the drugs on the market (2005). As a result, GPCRs continue to be at the forefront of research in both small and large drug companies. However one of the difficulties in studying this diverse class of membrane proteins is their tendency to denature in aqueous solution. As a result there is a pressing need to develop new detergents to solubilise, stabilise and crystallise GPCRs in their native form for further study. Cholesterol analogues have been shown to be important for stabilising membrane proteins and preventing their thermal inactivation. In addition the β2-adrenergic receptor, a GPCR membrane protein, has been crystallised in the active state with two cholesterol molecules bound between the I, II, III and IV helices of the protein. This appears to represent a distinct cholesterol binding pocket on the membrane protein that is speculated to be conserved across up to 44% of the rhodopsin class of GPCRs. CHOBIMALT is a cholesterol-based detergent that has been shown to exhibit promising GPCR-stabilising properties. When benchmarked against other cholesterol based detergents it was found to be superior to all others tested except for cholesteryl hemisuccinate.1 CHOBIMALT has an aggregation number of roughly 200 and forms 210 ± 30 kDa micelles, which are significantly larger than those of most detergents used for biological systems which is likely due to the packing constraints associated with CHOBMALT’s large polar headgroup.2 As a result, CHOBIMALT is used mostly as an additive to other commercially available detergents in order to decrease micelle size. A branched dimaltoside motif is common in recently synthesised detergents by Chae and co-workers. These detergents have shown promising detergent properties, for example the maltose neopentyl glycol (MNG) detergent synthesised by Chae. This branched dimaltoside detergent was shown to be able to solubilise and stabilise the very labile light harvesting complex I (LHI) from Rhodopsin capsulatus in its active form for 20 days with little loss of protein conformation.3 A cholesterol-based detergent was envisaged that combines the cholesterol framework of CHOBIMALT but replaces its linear tetrasaccharide with a branched dimaltoside. This detergent would then be investigated to assess its ability to solubilise, stabilise and crystallise GPCR proteins. This cholesterol-based detergent (shown below) was eventually synthesised in 9 linear steps from cholesterol.

Grain coarsening in contact metamorphic carbonates: effects of second-phase particles, fluid flow and thermal perturbations

Under contact metamorphic conditions, carbonate rocks in the direct vicinity of the Adamello pluton reflect a temperature-induced grain coarsening. Despite this large-scale trend, a considerable grain size scatter occurs on the outcrop-scale indicating local influence of second-order effects such as thermal perturbations, fluid flow and second-phase particles. Second-phase particles, whose sizes range from nano- to the micron-scale, induce the most pronounced data scatter resulting in grain sizes too small by up to a factor of 10, compared with theoretical grain growth in a pure system. Such values are restricted to relatively impure samples consisting of up to 10 vol.% micron-scale second-phase particles, or to samples containing a large number of nano-scale particles. The obtained data set suggests that the second phases induce a temperature-controlled reduction on calcite grain growth. The mean calcite grain size can therefore be expressed in the form D 1⁄4 C2 eQ*/RT(dp/fp)m*, where C2 is a constant, Q* is an activation energy, T the temperature and m* the exponent of the ratio dp/fp, i.e. of the average size of the second phases divided by their volume fraction. However, more data are needed to obtain reliable values for C2 and Q*. Besides variations in the average grain size, the presence of second-phase particles generates crystal size distribution (CSD) shapes characterized by lognormal distributions, which differ from the Gaussian-type distributions of the pure samples. In contrast, fluid-enhanced grain growth does not change the shape of the CSDs, but due to enhanced transport properties, the average grain sizes increase by a factor of 2 and the variance of the distribution increases. Stable d18O and d13C isotope ratios in fluid-affected zones only deviate slightly from the host rock values, suggesting low fluid/rock ratios. Grain growth modelling indicates that the fluid-induced grain size variations can develop within several ka. As inferred from a combination of thermal and grain growth modelling, dykes with widths of up to 1 m have only a restricted influence on grain size deviations smaller than a factor of 1.1.To summarize, considerable grain size variations of up to one order of magnitude can locally result from second-order effects. Such effects require special attention when comparing experimentally derived grain growth kinetics with field studies.

Studies of the gastro-oesophageal junction in normal and overweight healthy volunteers

Introduction: Oesophageal adenocarcinoma has increased dramatically in incidence over the past three decades with a particularly high burden of disease at the gastro-oesophageal junction. Many cases occur in individuals without known gastro-oesophageal reflux disease and in the absence of Barrett’s oesophagus suggesting that mechanisms other than traditional reflux may be important. Distal squamous mucosa may be prone to acid damage even in the absence of traditional reflux by the mechanism of distal opening of the lower oesophageal sphincter. This is splaying of the distal segment of lower oesophageal sphincter allowing acid ingress without traditional reflux. It has been suggested that the cardiac mucosa at the gastro-oesophageal junction, separating oesophageal squamous mucosa and acid secreting columnar mucosa of the stomach may be an abnormal mucosa arising as a consequence of acid damage. By this theory the cardiac mucosa is metaplastic and akin to ultra-short Barrett’s oesophagus. Obesity is a known risk factor for adenocarcinoma at the gastro-oesophageal junction and its rise has paralleled that of oesophageal cancer. Some of this excess risk undoubtedly operates through stress on the gastro-oesophageal junction and a predisposition to reflux. However we sought to explore the impact of obesity on the gastro-oesophageal junction in healthy volunteers without reflux and in particular to determine the characteristics of the cardiac mucosa and mechanisms of reflux in this group. Methods: 61 healthy volunteers with normal and increased waist circumference were recruited. 15 were found to have a hiatus hernia during the study protocol and were analysed separately. Volunteers had comprehensive pathological, physiological and anatomical assessments of the gastro-oesophageal junction including endoscopy with biopsies, MRI scanning before and after a standardised meal, prolonged recording of pH and manometry before and after a meal and screening by fluoroscopy to identify the squamo-columnar junction. In the course of the early manometric assessments a potential error associated with the manometry system recordings was identified. We therefore also sought to document and address this on the benchtop and in vivo. Key Findings: 1. In documenting the behaviour of the manoscan we described an immediate effect of temperature change on the pressure recorded by the sensors; ‘thermal effect’ and an ongoing drift of the recorded pressure with time; ‘baseline drift’. Thermal effect was well compensated within the standard operation of the system but baseline drift not addressed. Applying a linear correction to recorded data substantially reduced the error associated with baseline drift. 2. In asymptomatic healthy volunteers there was lengthening of the cardiac mucosa in association with central obesity and age. Furthermore, the cardiac mucosa in healthy volunteers demonstrated an almost identical immunophenotype to non-IM Barrett’s mucosa, which is considered to arise by metaplasia of oesophageal squamous mucosa. These findings support the hypothesis that the cardia is metaplastic in origin. 3. We have demonstrated a plausible mechanism of damage to distal squamous mucosa in association with obesity. In those with a large waist circumference we observed increased ingress of acid within but not across the lower oesophageal sphincter; ‘intrasphincteric reflux’ 4. The 15 healthy volunteers with a hiatus hernia were compared to 15 controls matched for age, gender and waist circumference. Those with a hiatus hernia had a longer cardiac mucosa and although they did not have excess traditional reflux they had excess distal acid exposure by short segment acid reflux and intrasphincteric acid reflux. Conclusions: These findings are likely to be relevant to adenocarcinoma of the gastro-oesophageal junction

On the temperature stability of extracellular hemoglobin of Glossoscolex paulistus, at different oxidation states: SAXS and DLS studies

Glossoscolex paulistus hemoglobin (HbGp) was studied by dynamic light scattering (DLS) and small angle X-ray scattering (SAXS). DLS melting curves were measured for met-HbGp at different concentrations. SAXS temperature studies were performed for oxy-, cyanomet- and met-HbGp forms, at several pH values. At pH 5.0 and 6.0, the scattering curves are identical from 20 to 60 degrees C, and R-g is 108 angstrom, independent of the oxidation form. At pH 7.0, protein denaturation and aggregation occurs above 55 degrees C and 60 degrees C, for oxy and met-HbGp, respectively. Cyanomet-HbGp, at pH 7.0, is stable up to 60 degrees C. At alkaline pH (8.0-9.0) and higher temperature, an irreversible dissociation process is observed, with a decrease of R-g, D-max and I(0). Analysis by p(r), obtained from GNOM, and OLIGOMER, was used to fit the SAXS experimental scattering curves by a combination of theoretical curves obtained for HbLt fragments from the crystal structure. Our results show clearly the increasing contribution of smaller molecular weight fragments, as a function of increasing pH and temperature, as well as, the order of thermal stabilities: cyanomet-> oxy- > met-HbGp. (C) 2012 Elsevier B.V. All rights reserved.

Thermal analysis in the drilling of solid rigid foam materials and ex-vivo bovine bones

Bone is a dynamic, highly vascularized tissue with a unique capacity to heal and regenerate without scarring. However, drilling remains a concern in several clinical procedures due to thermal damage of the bone and surrounding tissue. The success of this surgeries is dependent of many factors and also in temperature generation during the drilling bone. When an excessive heat is produced during the drilling, thermal necrosis can occur and the bone suffers injuries. Studies have shown that the increased temperature is directly related with the drilling parameters, particularly, the drill speed, feed-rate, applied force, the depth of cut, the geometry of the drill bit, the use or not of a cooling system and also the type of bone.

Large Rayleigh number thermal convection: heat flux predictions and strongly nonlinear solutions

We investigate the structure of strongly nonlinear Rayleigh–Bénard convection cells in the asymptotic limit of large Rayleigh number and fixed, moderate Prandtl number. Unlike the flows analyzed in prior theoretical studies of infinite Prandtl number convection, our cellular solutions exhibit dynamically inviscid constant-vorticity cores. By solving an integral equation for the cell-edge temperature distribution, we are able to predict, as a function of cell aspect ratio, the value of the core vorticity, details of the flow within the thin boundary layers and rising/falling plumes adjacent to the edges of the convection cell, and, in particular, the bulk heat flux through the layer. The results of our asymptotic analysis are corroborated using full pseudospectral numerical simulations and confirm that the heat flux is maximized for convection cells that are roughly square in cross section.

A SCR Model based on Reactor and Engine Experimental Studies for a Cu-zeolite Catalyst

A NOx reduction efficiency higher than 95% with NH3 slip less than 30 ppm is desirable for heavy-duty diesel (HDD) engines using selective catalytic reduction (SCR) systems to meet the US EPA 2010 NOx standard and the 2014-2018 fuel consumption regulation. The SCR performance needs to be improved through experimental and modeling studies. In this research, a high fidelity global kinetic 1-dimensional 2-site SCR model with mass transfer, heat transfer and global reaction mechanisms was developed for a Cu-zeolite catalyst. The model simulates the SCR performance for the engine exhaust conditions with NH3 maldistribution and aging effects, and the details are presented. SCR experimental data were collected for the model development, calibration and validation from a reactor at Oak Ridge National Laboratory (ORNL) and an engine experimental setup at Michigan Technological University (MTU) with a Cummins 2010 ISB engine. The model was calibrated separately to the reactor and engine data. The experimental setup, test procedures including a surrogate HD-FTP cycle developed for transient studies and the model calibration process are described. Differences in the model parameters were determined between the calibrations developed from the reactor and the engine data. It was determined that the SCR inlet NH3 maldistribution is one of the reasons causing the differences. The model calibrated to the engine data served as a basis for developing a reduced order SCR estimator model. The effect of the SCR inlet NO2/NOx ratio on the SCR performance was studied through simulations using the surrogate HD-FTP cycle. The cumulative outlet NOx and the overall NOx conversion efficiency of the cycle are highest with a NO2/NOx ratio of 0.5. The outlet NH3 is lowest for the NO2/NOx ratio greater than 0.6. A combined engine experimental and simulation study was performed to quantify the NH3 maldistribution at the SCR inlet and its effects on the SCR performance and kinetics. The uniformity index (UI) of the SCR inlet NH3 and NH3/NOx ratio (ANR) was determined to be below 0.8 for the production system. The UI was improved to 0.9 after installation of a swirl mixer into the SCR inlet cone. A multi-channel model was developed to simulate the maldistribution effects. The results showed that reducing the UI of the inlet ANR from 1.0 to 0.7 caused a 5-10% decrease in NOx reduction efficiency and 10-20 ppm increase in the NH3 slip. The simulations of the steady-state engine data with the multi-channel model showed that the NH3 maldistribution is a factor causing the differences in the calibrations developed from the engine and the reactor data. The Reactor experiments were performed at ORNL using a Spaci-IR technique to study the thermal aging effects. The test results showed that the thermal aging (at 800°C for 16 hours) caused a 30% reduction in the NH3 stored on the catalyst under NH3 saturation conditions and different axial concentration profiles under SCR reaction conditions. The kinetics analysis showed that the thermal aging caused a reduction in total NH3 storage capacity (94.6 compared to 138 gmol/m3), different NH3 adsorption/desorption properties and a decrease in activation energy and the pre-exponential factor for NH3 oxidation, standard and fast SCR reactions. Both reduction in the storage capability and the change in kinetics of the major reactions contributed to the change in the axial storage and concentration profiles observed from the experiments.

Energy consumption and energy efficiency in olive oil mills: case studies in Portugal and Spain in the frame of TESLA project

TESLA project (Transfering Energy Save Laid on Agroindustry) financed by the European Commission, had the main goals of evaluating the energy consumption and to identify the best available practices to improve energy efficiency in key agro-food sectors, such as the olive oil mills. A general analysis of energy consumptions allowed identifying the partition between electrical and thermal energy (approximately 50%) and the production processes responsible for the higher energy consumptions, as being the in the mill and paste preparation and the phases separation. Some measures for reducing energy waste and for improving energy efficiency were identified and the impact was evaluated by using the TESLA tool developed by Circe and available at the TESLA website.