Fabrication and optimizing of metal nano silicate as toxic metal absorbent from sea water

Pure Water, is a crucial demand of creature life. Following industrial development, extra amount of toxic metals such as chromium enters the environmental cycle through the sewage, which is considered as a serious threat for organisms. One of the modern methods of filtration and removal of contaminants in water, is applying Nano-technology. According to specific property of silicate materials, in this article we try to survey increased power in composites and various absorption in several morphologies and also synthesis of Nano-metal silicates with different morphologies as absorbent of metal toxic ions. At first, we synthesize nano zink silicate with three morphologies considering context and the purpose of this survey. 1) Nano synthesis of zink silicate hollow cavity by hydrothermal method in mixed solvent system of ethanol/glycol polyethylene. 2) Zink nano wires silicate in a water-based system by controlling the amount of sodium silicate. 3) Synthesis of nano zink silicate membrane. After synthesizing, we measured the cadmium ion absorbance by synthesized nano zink silicates. Controlling PH, is the applied absorption method. Next step, we synthesized nano zink-magnesium silicate composite in two various morphologies of nanowires and membrane by different precent of zink and magnesium, in order to optimize synthesized nano metal silicate. We used zink nitrate and magnesium nitrate and also measured cadmium absorption by synthesized nano metal silicates in the same way of PH control absorption. In the 3rd step, in order to determine the impact of the type of metal in nano metal silicate, we synthesized nano magnesium silicate and compared its absorption with nano zink silicate. Furthermore, we calculated the optimal concentration in one of synthesizes. Optimal concentration is the process which has the maximum absorption. While applying two methods of absorption in the test, finally we compared the effect of absorption method on the absorption level. Below you find further steps of synthesis: 1) Using IR, RAMAN, XRD spectroscopy to check the accuracy of synthesis. 2) Checking the dispersion of nano particles in ethanol solution by light microscope. 3) Measuring and observing particles with scanning electron microscope (SEM). 4) Using atomic absorption device for measuring the cadmium concentration in water-based solutions. The nano metal silicates were synthesized successfully. All of synthesized nano absorbents have the cadmium ion absorbency. The cadmium absorption via nano absorbents depend on various factors such as kind of metal in nano silicate and percent of metal in nano metal silicate composite. Meanwhile the absorption and PH control of medium containing the absorbent and solution would affect the cadmium absorption.

Utilização de resíduos de catalisador (ECAT) e cinzas da casca de arroz (CCA) na elaboração de vidros silicatos soda-cal destinados a embalagem

Dissertação (Mestrado em Tecnologia Nuclear)

Estudo da adsorção de íons metálicos em caulinita para água de reuso

Dissertação (Mestrado em Tecnologia Nuclear)

Organic compounds on comet 67P/Churyumov-Gerasimenko revealed by COSAC mass spectrometry

Comets harbor the most pristine material in our solar system in the form of ice, dust, silicates, and refractory organic material with some interstellar heritage. The evolved gas analyzer Cometary Sampling and Composition (COSAC) experiment aboard Rosetta's Philae lander was designed for in situ analysis of organic molecules on comet 67P/Churyumov-Gerasimenko. Twenty-five minutes after Philae's initial comet touchdown, the COSAC mass spectrometer took a spectrum in sniffing mode, which displayed a suite of 16 organic compounds, including many nitrogen-bearing species but no sulfur-bearing species, and four compounds-methyl isocyanate, acetone, propionaldehyde, and acetamide-that had not previously been reported in comets.

Critical core mass for enriched envelopes: the role of H2O condensation

Context. Within the core accretion scenario of planetary formation, most simulations performed so far always assume the accreting envelope to have a solar composition. From the study of meteorite showers on Earth and numerical simulations, we know that planetesimals must undergo thermal ablation and disruption when crossing a protoplanetary envelope. Thus, once the protoplanet has acquired an atmosphere, not all planetesimals reach the core intact, i.e. the primordial envelope (mainly H and He) gets enriched in volatiles and silicates from the planetesimals. This change of envelope composition during the formation can have a significant effect on the final atmospheric composition and on the formation timescale of giant planets. Aims. We investigate the physical implications of considering the envelope enrichment of protoplanets due to the disruption of icy planetesimals during their way to the core. Particular focus is placed on the effect on the critical core mass for envelopes where condensation of water can occur. Methods. Internal structure models are numerically solved with the implementation of updated opacities for all ranges of metallicities and the software Chemical Equilibrium with Applications to compute the equation of state. This package computes the chemical equilibrium for an arbitrary mixture of gases and allows the condensation of some species, including water. This means that the latent heat of phase transitions is consistently incorporated in the total energy budget. Results. The critical core mass is found to decrease significantly when an enriched envelope composition is considered in the internal structure equations. A particularly strong reduction of the critical core mass is obtained for planets whose envelope metallicity is larger than Z approximate to 0.45 when the outer boundary conditions are suitable for condensation of water to occur in the top layers of the atmosphere. We show that this effect is qualitatively preserved even when the atmosphere is out of chemical equilibrium. Conclusions. Our results indicate that the effect of water condensation in the envelope of protoplanets can severely affect the critical core mass, and should be considered in future studies.

Etude écologique de projet. Site de Flamanville. 1er cycle. Traitements mathématiques, Rapport général, Annexes

The study of a first annual hydrobiological cycle on the site of Flamanville was carried out through 19 campaigns conducted between July 76 and June 77. Twelve of them are considered as "heavy" and took place on the following dates: July 8th, 76; August 6th, September 4th, October 3rd, November 3rd, December 16th, January 5th, 77; February 2nd, March 3rd, April 14th, May 10th and May 24th. Seven campaigns consist only in one sample July 23rd, 76; August 21st, September 16th, November 19th, January 19th, 77; February 17th and June 16th. However, some variables which had not been measured during these "light" missions have not been taken into account for the analysis. A first global analysis groups together the first ten campaigns (in May, the nutritive salts had not been measured) and presents the annual variations of nine parameters: temperature, salinity, oxygen, nitrates (N0 3), nitrites (N0 2), phosphates (P0 4), silicates (Si0 2), chlorophyll and pheopigments. A second study of the annual hydrobiological cycle includes all campaigns but only five variables: temperature, salinity, oxygen, chlorophyll and pheopigments.

Adição de resíduo cerâmico em pastas geopoliméricas para cimentação de poços de petróleo

The development of activities the of oil and gas sector have promoted the search for suitable materials for cementing oil wells. In the state of the Rio Grande do Norte, the integrity of the cement sheath tends to be impaired during steam injection, a procedure necessary to increase oil recovery in reservoirs with low-viscosity oil. The geopolymer is a material that can be used as alternative cement, since it has been used in the production of fire-resistant components, building structures, and for the control of toxic or radioactive residues. Geopolymers result from condensation polymer alkali aluminosilicates and silicates resulting three-dimensional polymeric structures. They are produced in a manner different from that of Portland cement, which is made an activating solution that is mixed with geopolymer precursor. Among the few works studied allowed us to conclude that the pastes prepared with metakaolin as precursor showed better performance of its properties. Several studies show the addition of waste clay as a means of reducing cost and improving end of the folder properties. On this basis, the goal is to study the influence of the addition of ceramic waste in geopolymer paste. To develop the study of rheology tests were carried out, filtered, thickening time, compressive strength, free water, specific gravity and permeability, according to the American Pretoleum Institute (API). The results for all formulations studied show that the folders have high mechanical strength to a light paste; low filtrate volume, absence of free water, very low permeability, slurry, consistent with a light paste, and thickening time low that can be corrected with the use of a retardant handle. For morphological characterization, microstructural, physical, chemical and thermal tests were carried out by XRD, MEV, DTA, TG, FTIR. In the trial of XRD, it was found that geopolymer is an amorphous material, with a peak of crystalline kaolinite. In tests of TG / DTA, revealed the presence of a significant event, which represents the mass loss related to water, and also observed the reduction of weight loss by increasing the concentration of ceramic waste. In the trial of MEV, we found a uniform matrix without the presence of other phases. In the trial of FT-IR, we observed the presence of the band related to water. From all results it was determined that the optimum concentration range of use is between 2.5 and 5% of waste ceramic

Electron microprobe investigations of metamorphic reactions and mineral growth histories, Kwoiek area, British Columbia

The Kwoiek Area of British Columbia contains a pendant or screen of metamorphosed sedimentary and volcanic rocks almost entirely surrounded by a portion of the Coast Range Batholith, and intruded by several dozen stocks. The major metamorphic effects were produced by the quartz diorite batholithic rocks, with minor and later effects by the quartz diorite stocks. The sequence of important metamorphic reactions in the metasedimentary and metavolcanic rocks, ranging in grade from chlorite to sillimanite, is:

1. chlorite + carbonate + muscovite → epidote + biotite

2. chlorite + carbonate → actinolite + epidote

3. chlorite + muscovite → garnet + biotite

4. chlorite + epidote → garnet + hornblende

5. chlorite + muscovite → garnet + staurolite + biotite

6. chlorite + muscovite → aluminum silicate + biotite

7. muscovite + staurolite → garnet + aluminum silicate + biotite

8. staurolite → garnet + aluminum silicate

Continuous reactions, occurring between reactions 5 and 7, are:

A. chlorite + (high Ti) biotite + Al₂O₃ (from plagioclase?)→ garnet + staurolite + (low Ti) biotite + O₂

B. muscovite (phengitic) → garnet + staurolite +muscovite (less phengitic) + O₂ (?)

Detailed electron microprobe work on garnet, staurolite, biotite, and chlorite shows that:

(1) The garnet porphyroblasts are zoned according to a depletion model, called the Rayleigh depletion model, which assumes equilibrium between the edge of a growing garnet and the minerals which are unzoned, notably biotite, chlorite, and muscovite, but which assumes disequilibrium within the garnet.

(2) The staurolite porphyroblasts are also zoned, and from their zoning patterns reactions A, B, and 5 are documented. Progressive reduction of iron with increasing grade of metamorphism is also inferred from the staurolite zoning patterns.

(3) During a late period of falling temperature garnet continued to grow and the biotite and chlorite reequilibrated. The biotite, chlorite, and garnet edge compositions can vary from point to point in a given thin section, indicating that the volume of equilibrium at the final stage of metamorphism was only a few cubic microns.

(4) The horizon within the garnet that grew at maximum temperature can be identified. The Mg/Fe ratio of this horizon, if the garnet composition is a limiting composition in the Al₂O₃ - K₂O - FeO - MgO tetrahedron, increases systematically with increasing metamorphic grade. Biotite and chlorite compositions also show a general increase in Mg/Fe ratio with increasing metamorphic grade, but staurolite appears to show the reverse effect.

(5) The Mg/Fe ratio at the maximum temperature horizon of the garnet porphyroblasts is a function of its Mn content as evidenced from the study of five garnet-bearing rocks, collected from one outcrop area, with the same assemblage but with differing proportions of minerals.

An important implication of zoned minerals is that the effective composition of a system in a phase lies on the join between the homogeneous minerals (if there are two) and not within three-or- four-phase fields when a zoned mineral, such as garnet or staurolite, is present in the assemblage.

Study of the three aluminum silicates found in the Kwoiek Area showed that a constant pressure change in polymorphs from andalusite to kyanite to sillimanite took place with increasing temperature. This transition series is best explained by the metastable formation of andalusite.

Photographic materials on pages 15, 121, 160, 162, and 164 are essential and will not reproduce clearly on Xerox copies. Photographic copies should be ordered.

Dinâmica dos nutrientes na Ria Formosa: efeitos da interacçäo da laguna com as suas interfaces na reciclagem do azoto, fósforo e sílica

Tese de dout. em Ciências do Mar, Instituto de Investigação das Pescas e do Mar, Univ. do Algarve, 1996

Sinterização de matrizes cerâmicas à base de alumina reforçadas por carbetos a partir de precursores poliméricos

Ceramic composites produced with polymerics precursors have been studied for many years, due to the facility of obtaining a complex shape, at low temperature and reduces cost. The main objective of this work is to study the process of sintering of composites of ceramic base consisting of Al2O3 and silicates, reinforced for NbC, through the technique of processing AFCOP, as well as the influence of the addition of LZSA, ICZ and Al as materials infiltration in the physical and mechanical properties of the ceramic composite. Were produced ceramic matrix composites based SiCxOy e Al2O3 reinforced with NbC, by hidrosilylation reaction between D4Vi and D1107 mixtured with Al2O3 as inert filler, Nb and Al as reactive filler. The specimens produced were pyrolised at 1200, 1250 and 1400°C and infiltred with Al, ICZ and LZSA, respectively. Density, porosity, flexural mechanical strength and fracture surface by scanning electron microscopy were evaluated. The microstructure of the composites was investigated by X-ray diffraction to identify the presence of crystalline phases. The composites presented apparent porosity varying of 31 up to 49% and mechanical flexural strength of 14 up to 34 MPa. The infiltration process improviment of the densification and reduction of the porosity, as well as increased the values of mechanical flexural strength. The obtained phases had been identified as being Al3Nb, NbSi2, Nb5S3, Nb3Si and NbC. The samples that were submitted the infiltration process presented a layer next surface with reduced pores number in relation to the total volume

Strategies for the one-step immobilization–purification of enzymes as industrial biocatalysts

In this review, we detail the efforts performed to couple the purification and the immobilization of industrial enzymes in a single step. The use of antibodies, the development of specific domains with affinity for some specific supports will be revised. Moreover, we will discuss the use of domains that increase the affinity for standard matrices (ionic exchangers, silicates). We will show how the control of the immobilization conditions may convert some unspecific supports in largely specific ones. The development of tailor-made heterofunctional supports as a tool to immobilize–stabilize–purify some proteins will be discussed in deep, using low concentration of adsorbent groups and a dense layer of groups able to give an intense multipoint covalent attachment. The final coupling of mutagenesis and tailor made supports will be the last part of the review.