The reasonant influence of supply chain management practices on organizational performance

A single supply chain management (SCM) practice will have a certain impact on organizational performance(OP). However, since it is placed in a system that many other practices are conducted simultaneously, the practice itself will interact with other ones and have a greater impact on OP. This mechanism is named the "resonant" influence. The technique of Structural equation modelling (SEM) was used to test the above mechanism with data collected from Vietnamese garment enterprises. The tcst results showed that the model without mutual interaction among SCM practices could explain 42.8%, 26.3% and 34% variance of operational performance, customer satisfaction and financial performance. While the one containing this interaction is capable to explain 69.5%, 33.1% and 57.3%, respectively.

Plastic waste use as aggregate and binder modifier in open-graded asphalts

Road pavements are very important infrastructures for the Society, but they can cause serious environmental impacts during construction, operation and rehabilitation phases. Thus, it is essential to develop surface paving solutions that promote not only the durability but also a comfortable and safe use. In fact, this work aims to study the properties of new opengraded mixtures for surface layers produced with plastic wastes. First, HDPE and EVA wastes were used as bitumen modifiers, and then another plastic waste (PEX) replaced part of the aggregates. After studying the modified binders, the open-graded mixtures were designed, and then they were tested concerning their particle loss, rutting resistance, surface texture and damping effect. It was concluded that both ways of using the plastic wastes can improve the mechanical and functional properties of the open-graded mixtures related to the pavement performance.

Seismic behaviour of traditional timber frame walls: experimental results on unreinforced walls

Timber frame buildings are well known as an efficient seismic resistant structure and they are used worldwide. Moreover, they have been specifically adopted in codes and regulations during the XVIII and XIX centuries in the Mediterranean area. These structures generally consist of exterior masonry walls with timber elements embedded which tie the walls together and internal walls which have a timber frame with masonry infill and act as shearwalls. In order to preserve these structureswhich characterizemany cities in theworld it is important to better understand their behaviour under seismic actions. Furthermore, historic technologies could be used even in modern constructions to build seismic resistant buildings using more natural materials with lesser costs. Generally, different types of infill could be applied to timber frame walls depending on the country, among which brick masonry, rubble masonry, hay and mud. The focus of this paper is to study the seismic behaviour of the walls considering different types of infill, specifically: masonry infill, lath and plaster and timber frame with no infill. Static cyclic tests have been performed on unreinforced timber frame walls in order to study their seismic capacity in terms of strength, stiffness, ductility and energy dissipation. The tests showed how in the unreinforced condition, the infill is able to guarantee a greater stiffness, ductility and ultimate capacity of the wall.

Application of near surface mounted (NSM) strengthening technique to traditional timber frame walls

Timber frame buildings are well known as an efficient seismic resistant structure popular all over the world not only due to their seismic performance, but also to their low cost and the strength they offer. These constructions still exist today and it is important to be able to preserve them, so a better knowledge on their behaviour is sought. Furthermore, historic technologies could be used even in modern constructions to build seismic resistant buildings using more natural materials with lesser costs. A great rehabilitation effort is being carried out on this type of buildings, as their neglect has led to decay or their change in use and alterations to the structure has led to the need to retrofit such buildings; only recently studies on their behaviour have become available and only a few of them address the issue of possible strengthening techniques for this kind of walls. In this scope, an innovative retrofitting technique (near surface mounted steel flat bars) is proposed and validated on traditional timber frame walls based on an extensive experimental program. The results of the static cyclic tests on distinct wall typologies retrofitted with the NSM technique are herein presented and discussed in detail. The main features on deformation, lateral stiffness, lateral resistance and seismic performance indexes are analysed

Search for Higgs Boson Pair Production in the γγbb¯ Final State using pp Collision Data at s√=8TeV from the ATLAS Detector

Searches are performed for resonant and non-resonant Higgs boson pair production in the hh→γγbb¯ final state using 20 fb−1 of proton--proton collisions at a center-of-mass energy of 8TeV recorded with the ATLAS detector at the CERN Large Hadron Collider. A 95% confidence level upper limit on the cross section times branching ratio of non--resonant production is set at 2.2 pb, while the expected limit is 1.0 pb. The corresponding limit observed for a narrow resonance ranges between 0.8 and 3.5 pb as a function of its mass.

Surface plasmon resonance-coupled photoluminescence and resistive switching behavior of pulsed laser-deposited Ag:SiC nanocermet thin films

In this study, Ag:SiC nanocermets were prepared via rapid thermal annealing (RTA) of pulsed laser-deposited SiC/Ag/SiC trilayers grown on Si substrate. Atomic force microscope images show that silver nanoparticles (Ag NPs) are formed after RTA, and the size of NPs increases with increasing Ag deposition time (t Ag). Sharp dip observed in the reflectance spectra confirmed the existence of Ag surface plasmons (SPs). The infrared transmission spectra showed an intense and broad absorption band around 780–800 cm−1 that can be assigned to Si-C stretching vibration mode. Influence of t Ag on the spectral characteristics of SP-enhanced photoluminescence (PL) and electrical properties of silicon carbide (SiC) films has been investigated. The maximum PL enhancement by 5.5 times for Ag:SiC nanocermets is achieved when t Ag ≈ 50 s. This enhancement is due to the strong resonant coupling between SiC and the SP oscillations of the Ag NPs. Presence of Ag NPs in SiC also induces a forming-free resistive switching with switching ratio of 2 × 10−2. The analysis of I–V curves demonstrates that the trap-controlled space-charge-limited conduction with filamentary model is the governing mechanism for the resistive switching in nanocerment thin films.

Search for invisible particles produced in association with single-top-quarks in proton-proton collisions at s√ = 8 TeV with the ATLAS detector

A search for the production of single-top-quarks in association with missing energy is performed in proton--proton collisions at a centre-of-mass energy of s√ = 8 TeV with the ATLAS experiment at the Large Hadron Collider using data collected in 2012, corresponding to an integrated luminosity of 20.3 fb−1. In this search, the W boson from the top quark is required to decay into an electron or a muon and a neutrino. No deviation from the Standard Model prediction is observed, and upper limits are set on the production cross-section for resonant and non-resonant production of an invisible exotic state in association with a right-handed top quark. In the case of resonant production, for a spin-0 resonance with a mass of 500 GeV, an effective coupling strength above 0.15 is excluded at 95% confidence level for the top quark and an invisible spin-1/2 state with mass between 0 GeV and 100 GeV. In the case of non-resonant production, an effective coupling strength above 0.2 is excluded at 95% confidence level for the top quark and an invisible spin-1 state with mass between 0 GeV and 657 GeV.

Search for production of WW/WZ resonances decaying to a lepton, neutrino and jets in pp collisions at s√ = 8 TeV with the ATLAS detector

A search is presented for a narrow diboson resonances decaying to WW or WZ in the final state where one W boson decays leptonically (to an electron or a muon plus a neutrino) and the other W/Z boson decays hadronically. The analysis is performed using an integrated luminosity of 20.3 fb−1 of pp collisions at s√ = 8 TeV collected by the ATLAS detector at the LHC. No evidence for resonant diboson production is observed, and resonance masses below 700 GeV and 1490 GeV are excluded at 95% confidence level for the spin-2 Randall-Sundrum bulk graviton G∗ with coupling constant of 1.0 and the extended gauge model W′ boson respectively.

New control algorithm for single-phase series active power filter

This paper presents a single-phase Series Active Power Filter (Series APF) for mitigation of the load voltage harmonic content, while maintaining the voltage on the DC side regulated without the support of a voltage source. The proposed series active power filter control algorithm eliminates the additional voltage source to regulate the DC voltage, and with the adopted topology it is not used a coupling transformer to interface the series active power filter with the electrical power grid. The paper describes the control strategy which encapsulates the grid synchronization scheme, the compensation voltage calculation, the damping algorithm and the dead-time compensation. The topology and control strategy of the series active power filter have been evaluated in simulation software and simulations results are presented. Experimental results, obtained with a developed laboratorial prototype, validate the theoretical assumptions, and are within the harmonic spectrum limits imposed by the international recommendations of the IEEE-519 Standard.

Effect of surface plasmon resonance in TiO2/Au thin films on the fluorescence of self-assembled CdTe QDs structure

The exceptional properties of localised surface plasmons (LSPs), such as local field enhancement and confinement effects, resonant behavior, make them ideal candidates to control the emission of luminescent nanoparticles. In the present work, we investigated the LSP effect on the steady-state and time-resolved emission properties of quantum dots (QDs) by organizing the dots into self-assembled dendrite structures deposited on plasmonic nanostructures. Self-assembled structures consisting of water-soluble CdTe mono-size QDs, were developed on the surface of co-sputtered TiO2 thin films doped with Au nanoparticles (NPs) annealed at different temperatures. Their steady-state fluorescence properties were probed by scanning the spatially resolved emission spectra and the energy transfer processes were investigated by the fluorescence lifetime imaging (FLIM) microscopy. Our results indicate that a resonant coupling between excitons confined in QDs and LSPs in Au NPs located beneath the self-assembled structure indeed takes place and results in (i) a shift of the ground state luminescence towards higher energies and onset of emission from excited states in QDs, and (ii) a decrease of the ground state exciton lifetime (fluorescence quenching).

Modelling tyre-road noise with data mining techniques

The research aimed to establish tyre-road noise models by using a Data Mining approach that allowed to build a predictive model and assess the importance of the tested input variables. The data modelling took into account three learning algorithms and three metrics to define the best predictive model. The variables tested included basic properties of pavement surfaces, macrotexture, megatexture, and uneven- ness and, for the first time, damping. Also, the importance of those variables was measured by using a sensitivity analysis procedure. Two types of models were set: one with basic variables and another with complex variables, such as megatexture and damping, all as a function of vehicles speed. More detailed models were additionally set by the speed level. As a result, several models with very good tyre-road noise predictive capacity were achieved. The most relevant variables were Speed, Temperature, Aggregate size, Mean Profile Depth, and Damping, which had the highest importance, even though influenced by speed. Megatexture and IRI had the lowest importance. The applicability of the models developed in this work is relevant for trucks tyre-noise prediction, represented by the AVON V4 test tyre, at the early stage of road pavements use. Therefore, the obtained models are highly useful for the design of pavements and for noise prediction by road authorities and contractors.

Influence of the hip joint modeling approaches on the kinematics of human gait

The influence of the hip joint formulation on the kinematic response of the model of human gait is investigated throughout this work. To accomplish this goal, the fundamental issues of the modeling process of a planar hip joint under the framework of multibody systems are revisited. In particular, the formulations for the ideal, dry, and lubricated revolute joints are described and utilized for the interaction of femur head inside acetabulum or the hip bone. In this process, the main kinematic and dynamic aspects of hip joints are analyzed. In a simple manner, the forces that are generated during human gait, for both dry and lubricated hip joint models, are computed in terms of the system’s state variables and subsequently introduced into the dynamics equations of motion of the multibody system as external generalized forces. Moreover, a human multibody model is considered, which incorporates the different approaches for the hip articulation, namely ideal joint, dry, and lubricated models. Finally, several computational simulations based on different approaches are performed, and the main results presented and compared to identify differences among the methodologies and procedures adopted in this work. The input conditions to the models correspond to the experimental data capture from an adult male during normal gait. In general, the obtained results in terms of positions do not differ significantly when the different hip joint models are considered. In sharp contrast, the velocity and acceleration plotted vary significantly. The effect of the hip joint modeling approach is clearly measurable and visible in terms of peaks and oscillations of the velocities and accelerations. In general, with the dry hip model, intra-joint force peaks can be observed, which can be associated with the multiple impacts between the femur head and the cup. In turn, when the lubricant is present, the system’s response tends to be smoother due to the damping effects of the synovial fluid.

Searches for Higgs boson pair production in the hh→bbττ,γγWW∗,γγbb,bbbb channels with the ATLAS detector

Searches for both resonant and non-resonant Higgs boson pair production are performed in the hh→bbττ,γγWW∗ final states using 20.3 fb−1 of pp collision data at a center-of-mass energy of 8 TeV recorded with the ATLAS detector at the Large Hadron Collider. No evidence of their production is observed and 95% confidence level upper limits on the production cross sections are set. These results are then combined with the published results of the hh→γγbb,bbbb analyses. An upper limit of 0.69 (0.47) pb on the non-resonant Standard Model like hh production is observed (expected), corresponding to 70 (48) times of the SM gg→hh cross section. For production via narrow resonances, cross section limits of hh production from a heavy Higgs boson decay are set as a function of the heavy Higgs boson mass. The observed (expected) limits range from 2.1 (1.1) pb at 260 GeV to 0.011 (0.018) pb at 1000 GeV. These results are interpreted in the context of two simplified scenarios of the Minimal Supersymmetric Standard Model.

Resonante Sensoren

Resonant sensors, acoustic sensors, QCM, viscoelastic films, interfacial phenomena

Propietats d'absorció bifotònica del tetrafenilporficè i el seu complex de palladi: potencials sensibilitzadors per a Teràpia Fotodinàmica bifotònica.

Estudi elaborat a partir d’una estada a la Universitat de Aarhus, Dinamarca, durant juliol 2006. En el present treball s’investiguen, per primer cop, les propietats de absorció bifotòniques del fotosensibilitzador 2,7,12,17-tetrafenilporficè (TPPo) i del seu complex de pal•ladi (II) (PdTPPo). Ambos compostos han rebut molta atenció com a possibles otosensibilitzadors per a Teràpia Fotodinàmica (TFD). S’utilitza la detecció de la fosforescència de l’oxigen singlet, centrada a 1270 nm i produïda per l’absorció de dos fotons, per quantificar la magnitud de la secció d’absorció bifotònica, "delta", dels porficèns estudiats. Els experiments se han dut a terme en el marge espectral 750-850 nm i a l’infraroig proper a 1100nm. Aquestes longituds d’ona corresponen a les zones d’absorció bifotònica en les bandes de Soret i Q. Les propietats bifotòniques obtingudes es comparen i contrasten amb les dades conegudes de la tetrafenilporfirina (TPP), isòmer estructural del tetrafenilporficè però amb més gran simetria, i es troba que en la banda de Soret (que coincideix amb la regió de la pell més transparent) els valors de delta per el TPPo i PdTPPo son aproximadament 2000 GM en el màxim, pràcticament cent vegades més grans que per la TPP. A més a més, aquestos valors son dos ordres de magnitud més grans que els obtinguts a l’irradiar a 1100 nm (bandes Q). Aquestes observacions es poden explicar mitjançant la amplificació per ressonància deguda a la presència de transicions monofotòniques ressonants en la regió de les bandes Q. Els elevats valors de "delta" obtinguts per els tetrafenilporficèns estudiats junt a les principals característiques que aquestos presenten (elevat rendiment de formació d’oxigen singlet, estabilitat química i fotoquímica, absència de citotoxicitat,...) qualifiquen al TPPo y PdTPPo com a possibles fotosensibilitzadors per a Teràpia Fotodinàmica Bifotònica.