Micro/nanostructured carbon composite modified with a hybrid redox mediator and enzymes as a glucose biosensor

A carbon micro/nanostructured composite based on cup-stacked carbon nanotubes (CSCNTs) grown onto a carbon felt has been found to be an efficient matrix for enzyme immobilization and chemical signal transduction. The obtained CSCNT/felt was modified with a copper hexacyanoferrate/polypyrrole (CuHCNFe/Ppy) hybrid mediator, and the resulting composite electrode was applied to H(2)O(2) detection, achieving a sensitivity of 194 +/- 15 mu A mmol(-1) L. The results showed that the CSCNT/felt matrix significantly increased the sensitivity of CuHCNFe/Ppy-based sensors compared to those prepared on a felt unrecovered by CSCNTs. Our data revealed that the improved sensitivity of the as-prepared CuHCNFe/Ppy-CSCNT/felt composite electrode can be attributed to the electronic interactions taking place among the CuHCNFe nanocrystals, Ppy layer and CSCNTs. In addition, the presence of CSCNTs also seemed to favor the dispersion of CuHCNFe nanocrystals over the Ppy matrix, even though the CSCNTs were buried under the conducting polymer layer. The CSCNT/felt matrix also enabled the preparation of a glucose biosensor whose sensitivity could be tuned as a function of the number of glucose oxidase (GOx) layers deposited through a Layer-by-Layer technique with an sensitivity of 11 +/- 2 mu A mmol(-1) L achieved at 15 poly(diallyldimethylammoniumchloride)/GOx bilayers. (C) 2011 Elsevier Ltd. All rights reserved.

Differential Acetyl Cholinesterase Inhibition by Volatile Oils from two Specimens of Marlierea racemosa (Myrtaceae) Collected from Different Areas of the Atlantic Rain Forest

The volatile oil composition and anti-acetyl cholinesterase activity were analyzed in two specimens of Marlierea racemosa growing in different areas of the Atlantic Rain Forest (Cananeia and Caraguatatuba, SP, Brazil). Component identifications were performed by GUMS and their acetyl cholinesterase inhibitory activity was measured through colorimetric analysis. The major constituent in both specimens was spathulenol (25.1 % in Cananeia and 31.9% in Caraguatatuba). However, the first one also presented monoterpenes (41.2%), while in the Carguatatuba plants, this class was not detected. The oils from the plants collected in Cananeia were able to inhibit the acetyl cholinesterase activity by LIP to 75%, but for oils from the other locality the maximal inhibition achieved was 35%. These results suggested that the monoterpenes are more effective in the inhibition of acetyl cholinesterase activity than sesquiterpenes as these compounds are present in higher amounts in the M. racemosa plants collected in Cananeia.

Host-guest system of 4-nerolidylcatechol in 2-hydroxypropyl-beta-cyclodextrin: preparation, characterization and molecular modeling

The interaction of 4-nerolidylcatechol (4-NRC), a potent antioxidant agent, and 2-hydroxypropyl-beta-cyclodextrin (HP-beta-CD) was investigated by the solubility method using Fourier transform infrared (FTIR) methods in addition to UV-Vis, (1)H-nuclear magnetic resonance (NMR) spectroscopy and molecular modeling. The inclusion complexes were prepared using grinding, kneading and freeze-drying methods. According to phase solubility studies in water a B(S)-type diagram was found, displaying a stoichiometry complexation of 2:1 (drug:host) and stability constant of 6494 +/- A 837 M(-1). Stoichiometry was established by the UV spectrophotometer using Job`s plot method and, also confirmed by molecular modeling. Data from (1)H-NMR, and FTIR, experiments also provided formation evidence of an inclusion complex between 4-NRC and HP-beta-CD. 4-NRC complexation indeed led to higher drug solubility and stability which could probably be useful to improve its biological properties and make it available to oral administration and topical formulations.

Constituents of Leaves Essential Oil of Talauma ovata A. St.-Hil. (Magnoliaceae)

Tire volatile constituents of the fresh leaves of Talauma ovata (Magnoliaceae) were extracted by hydrodistillation and analyzed by GC and GC/MS. Twenty-seven compounds were identified representing 98.8% of the total oil. The oil from this species showed to be constituted by monoterpenes and sesquiterpenes in the same ratio. Among the monoterpenes, limonene (34.8%) and alpha-pinene (11.3%) were the main constituents, and beta-bisabolene (10.7%) was the major substance for the sesquiterpene fraction.

Essential Oil from Leaves and Stem Bark of Southeastern Drimys brasiliensis Miers (Winteraceae)

The chemical composition of essential oils obtained from fresh leaves and stem bark of Southeastern Brazilian native Drimys brasiliensis Miers were analyzed by GC and GC/MS and 37 compounds were identified. The oils from fresh leaves showed the presence of monoterpenes (53.9%) and sesquiterpenes (38.4%), with sabinene (9.5%), myrcene (10.5%), limonene (10.6%) and cyclocolorenone (16.0%) being the most abundant. The stern bark oil was characterized by predominance of sesquiterpenoids (87.6%) and the absence of monoterpenes, the main components being cyclocolorenone (28.3%) and spathuleneol (22.9%). A small amount of phenylpropanes (6.8-6.9%) was also detected in both oil samples.

Chemical Composition and Antimicrobial Activity of the Essential Oil from Croton heterocalyx Baill. (Euphorbiaceae s.s.) Leaves

The chemical composition and the antimicrobial activity of the essential oil from Croton heterocalyx leaves were evaluated. The oil which was analyzed by GC and GUMS was found to contain germacrene D (12.5%), bicyclogermacrene (11.2%), delta-elemene (9.2%) beta-elemene (8.2%), spathulenol (6.9%), linalool (5.4%) and 1,8-cineole (3.7%) its major components. Croton. heterocalyx oil displayed a high inhibitory activity against the fungi Aspergillus niger (16404) and Candida albicans (ATCC 10231.) as well its the Gram-positive bacterium Staphylococcus aureus (ATCC 6538), hut a very weak activity was observed for the Gram-negative bacteria Escherichia coli (ATCC 8739) and Pseudomonas aeruginosa (ATCC 9027).

Synthesis, Spectroscopic Studies and X-ray Crystal Structures of New Pyrazoline and Pyrazole Derivatives

The synthesis and characterization of some pyrazoline compounds of 1,3-diketones with hydrazine derivatives, namely, 1-(S-benzyldithiocarbazate)-3-methyl-5-phenyl-5-hydroxypyrazoline (1); 1-(2-thiophenecarboxylic)-3-methyl-5-phenyl-5-hydroxypyrazoline (2); 1-(2-thiophenecarboxylic)-3,5-dimethyl-5-hydroxypyrazoline (3); 1-(S-benzyldithiocarbazato)-3-methyl-5-phenylpyrazole (4); 1-(2-thiophenecarboxylic)-3-methyl-5-phenylpyrazole (5) and 1-(S-benzyldithiocarbazate)-3,5-dimethylpyrazole (6) are reported. Studies by IR, ((1)H, (13)C)-NMR spectroscopies and single crystal X-ray diffraction revealed that compounds (1)(,) (2) and (3) are formed as pyrazoline, whereas (4) and (5) are formed as pyrazole derivatives only under acidic conditions. Compound (1) crystallizes in orthorhombic P2(1)2(1)2(1), a = 6.38960(10) angstrom, b = 12.9176(3) angstrom, c = 21.2552(5) angstrom, (2) crystallizes in monoclinic, P2(1)/n, a = 11.3617(2) angstrom, b = 8.4988(2) angstrom, c = 92.8900(10)angstrom and beta = 92.8900(5)degrees, (3) crystallizes in monoclinic, C2/c, a = 15.9500(5) angstrom, b = 9.3766(3) angstrom, c = 16.6910(5)angstrom and beta = 113.825(2)degrees, (4) crystallizes in monoclinic, P2(1)/c, a = 15.228(4) angstrom, b = 5.5714(13) angstrom, c = 19.956(5)angstrom and beta = 91.575(7)degrees and (6) crystallizes in orthorhombic, P2(1)2(1)2(1), a = 5.3920(2) angstrom, b = 11.2074(5) angstrom, c = 21.885(1)angstrom . The (3) derivative represents the first pyrazoline compound prepared from 2,4-pentanedione and characterized crystallographically.

Synthesis, spectroscopic characterization and X-ray structures of five-coordinate diorganotin(IV) complexes containing 5-hydroxypyrazoline derivatives as ligands

Four new diorganotin(IV) complexes have been prepared from R(2)SnCl(2) (R = Me, Ph) with the ligands 5-hydroxy-3-metyl-5-phenyl-1-(S-benzildithiocarbazate)-pyrazoline (H(2)L(1)) and 5-hydroxy-3-methyl-5-phenyl-1-(2-thiophenecarboxylic)-pyrazoline (H(2)L(2)). The complexes were characterized by elemental analysis, IR. (1)H (13)C, (119)Sn NMR and Mossbauer spectroscopes The complexes [Me(2)SnL(1)], [Ph(2)SnL(1)] and [Me(2)SnL(2)] were also studied by single crystal X-ray diffraction and the results showed that the Sn(IV) central atom of the complexes adopts a distorted trigonal bipyramidal (TBP) geometry with the N atom of the ONX-tridentate (X = O and S) ligand and two organic groups occupying equatorial sites. The C-Sn-C angles for [Me(2)Sn(L(1))] and [Ph(2)Sn(L(1))] were calculated using a correlation between (119)Sn Mossbauer and X-ray crystallographic data based on the point-charge model Theoretical calculations were performed with the B3LYP density functional employing 3-21G(*) and DZVP all electron basis sets showing good agreement with experimental findings General and Sn(IV) specific IR harmonic frequency scale factors for both basis sets were obtained from comparison with selected experimental frequencies (C) 2010 Elsevier B V All rights reserved

Dynamic whole system testing of combined renewable heating systems : the current state of the art

Objective: For the evaluation of the energetic performance of combined renewable heating systems that supply space heat and domestic hot water for single family houses, dynamic behaviour, component interactions, and control of the system play a crucial role and should be included in test methods. Methods: New dynamic whole system test methods were developed based on “hardware in the loop” concepts. Three similar approaches are described and their differences are discussed. The methods were applied for testing solar thermal systems in combination with fossil fuel boilers (heating oil and natural gas), biomass boilers, and/or heat pumps. Results: All three methods were able to show the performance of combined heating systems under transient operating conditions. The methods often detected unexpected behaviour of the tested system that cannot be detected based on steady state performance tests that are usually applied to single components. Conclusion: Further work will be needed to harmonize the different test methods in order to reach comparable results between the different laboratories. Practice implications: A harmonized approach for whole system tests may lead to new test standards and improve the accuracy of performance prediction as well as reduce the need for field tests.

Testing of combined heating systems for small houses: Improved procedures for whole system test methods : Deliverable 2.3

Dynamic system test methods for heating systems were developed and applied by the institutes SERC and SP from Sweden, INES from France and SPF from Switzerland already before the MacSheep project started. These test methods followed the same principle: a complete heating system – including heat generators, storage, control etc., is installed on the test rig; the test rig software and hardware simulates and emulates the heat load for space heating and domestic hot water of a single family house, while the unit under test has to act autonomously to cover the heat demand during a representative test cycle. Within the work package 2 of the MacSheep project these similar – but different – test methods were harmonized and improved. The work undertaken includes:  • Harmonization of the physical boundaries of the unit under test. • Harmonization of the boundary conditions of climate and load. • Definition of an approach to reach identical space heat load in combination with an autonomous control of the space heat distribution by the unit under test. • Derivation and validation of new six day and a twelve day test profiles for direct extrapolation of test results.   The new harmonized test method combines the advantages of the different methods that existed before the MacSheep project. The new method is a benchmark test, which means that the load for space heating and domestic hot water preparation will be identical for all tested systems, and that the result is representative for the performance of the system over a whole year. Thus, no modelling and simulation of the tested system is needed in order to obtain the benchmark results for a yearly cycle. The method is thus also applicable to products for which simulation models are not available yet. Some of the advantages of the new whole system test method and performance rating compared to the testing and energy rating of single components are:  • Interaction between the different components of a heating system, e.g. storage, solar collector circuit, heat pump, control, etc. are included and evaluated in this test. • Dynamic effects are included and influence the result just as they influence the annual performance in the field. • Heat losses are influencing the results in a more realistic way, since they are evaluated under "real installed" and representative part-load conditions rather than under single component steady state conditions.   The described method is also suited for the development process of new systems, where it replaces time-consuming and costly field testing with the advantage of a higher accuracy of the measured data (compared to the typically used measurement equipment in field tests) and identical, thus comparable boundary conditions. Thus, the method can be used for system optimization in the test bench under realistic operative conditions, i.e. under relevant operating environment in the lab.   This report describes the physical boundaries of the tested systems, as well as the test procedures and the requirements for both the unit under test and the test facility. The new six day and twelve day test profiles are also described as are the validation results.

Uma metodologia unificada no domínio tempo para sistemas concentrados, discretos e distribuídos

A resposta impulso é utilizada como ferramenta padrão no estudo direto de sistemas concentrados, discretos e distribuídos de ordem arbitrária. Esta abordagem leva ao desenvolvimento de uma plataforma unificada para a obtenção de respostas dinâmicas. Em particular, as respostas forçadas dos sistemas são decompostas na soma de uma resposta permanente e de uma resposta livre induzida pelos valores iniciais da resposta permanente. A teoria desenvolve-se de maneira geral e direta para sistemas de n-ésima ordem, introduzindo-se a base dinâmica gerada pela resposta impulso na forma padrão e normalizada, sem utilizar-se a formulação de estado, através da qual reduz-se um sistema de ordem superior para um sistema de primeira ordem. Considerou-se sistemas de primeira ordem a fim de acompanhar-se os muitos resultados apresentados na literatura através da formulação de espaço de estado. Os métodos para o cálculo da resposta impulso foram classificados em espectrais, não espectrais e numéricos. A ênfase é dada aos métodos não espectrais, pois a resposta impulso admite uma fórmula fechada que requer o uso de três equações características do tipo algébrica, diferencial e em diferenças Realizou-se simulações numéricas onde foram apresentados modelos vibratórios clássicos e não clássicos. Os sistemas considerados foram sistemas do tipo concentrado, discreto e distribuído. Os resultados da decomposição da resposta dinâmica de sistemas concentrados diante de cargas harmônicas e não harmônicas foram apresentados em detalhe. A decomposição para o caso discreto foi desenvolvida utilizando-se os esquemas de integração numérica de Adams-Basforth, Strömer e Numerov. Para sistemas distribuídos, foi considerado o modelo de Euler-Bernoulli com força axial, sujeito a entradas oscilatórias com amplitude triangular, pulso e harmônica. As soluções permanentes foram calculadas com o uso da função de Green espacial. A resposta impulso foi aproximada com o uso do método espectral.

Ascensão e queda na mortalidade por doença isquêmica do coração no século XX : a epidemia nos EUA e um inquérito epidemiológico sobre sua causa

Os fatores de risco clássicos para o desenvolvimento de doença isquêmica do coração (DIC) explicam menos de 50% da queda na mortalidade observada desde 1950. A transição em curso, do paradigma degenerativo para o inflamatório/infeccioso, requer nova interpretação causal das tendências temporais. Este é um estudo ecológico, baseado em dados dos Estados Unidos, que mostra, em homens e mulheres, uma associação entre a distribuição etária da mortalidade por influenza e pneumonia (I&P) associada à pandemia de influenza de 1918-1919 na faixa dos 10 aos 49 anos e a distribuição da mortalidade por DIC, entre 1920 e 1985, em sobreviventes das coortes de nascimento correspondentes. Mostra ainda uma correlação negativa significativa (r = -0,68, p = 0,042) entre o excesso de mortalidade por I&P acumulado em epidemias entre 1931-1940 (utilizado como indicador da persistência da circulação de vírus H1N1 aliada à vulnerabilidade à infecção) e a ordem do início do declínio na mortalidade por DIC, em nove divisões geográficas dos Estados Unidos. Os dados sugerem, à luz do conhecimento biológico atual, que a pandemia de influenza de 1918 (e as que se seguiram até 1957) pudesse ter tido papel determinante na epidemia de mortalidade por DIC registrada no século XX.

Contribuição para a identificação dos principais fatores e mecanismos de degradação em edificações do patrimônio cultural de Porto Alegre

A presença de um universo de fatores adversos tem levado as edificações do patrimônio cultural a graus avançados de degradação e, muitas vezes, à perda total. O estudo de danos em edificações considera que, sendo conhecidas as causas da degradação, mais eficientes podem vir a ser os diagnósticos e mais adequadas as soluções de saneamento. Este trabalho apresenta, através de urna visão generalista e sistemática, urna contribuição para a identificação dos principais fatores de degradação e dos danos causados pelos mesmos. Agentes climáticos, agentes biológicos e a ação do homem são apontados pela pesquisa bibliográfica corno os principais agentes de degradação. A descrição sistemática proposta foi realizada através de urna revisão das características verificadas com maior freqüência e que devem ser percebidas pelo técnico ao avaliar as condições do prédio. Entendendo a atuação destes fatores, o técnico entra na edificação com um olhar muito mais apurado e crítico sobre as possíveis causas que estão levando a obra à ruína, além de avaliar os danos que devem ser tratados com prioridade. Com a finalidade de verificar as formas de atuação destes, foi realizado um estudo de caso múltiplo, a partir do levantamento de dados sobre urna amostra de edificações da cidade de Porto Alegre. Observou-se que, embora as condições climáticas sejam favoráveis à presença de alguns agentes, corno a umidade, por exemplo, aspectos referentes à ação do homem, corno a falta de conservação preventiva e as intervenções indevidas aparecem corno causas relevantes de danos As circunstâncias, freqüentemente, não permitem que sejam realizados os devidos trabalhos de conservação. Mesmo alguns, feitos sem a devida orientação, acabam por gerar danos ainda maiores. Verificou-se também que a avaliação do estado de degradação das edificações do patrimônio cultural requer um trabalho multidisciplinar, em função da gama de conhecimentos necessários para o entendimento da ação de todos os agentes e mecanismos.