(Appendix) Chemical composition of bottom sediments at DSDP Leg 72 Holes

The distributions of calcium carbonate, of amorphous silica, and of 21 chemical compounds and elements in sediments of Holes 515A, 515B, 516, 516F, 517, and 518 are highly nonuniform; they change depending on the sediment types, grain size, and mineral composition. The main source of the lithogenous elements (K, Li, Rb, Fe, Ti, Zr, Ni, Cr, Sn) is terrigenous matter of South America. These elements correlate well or at least satisfactorily with each other and with the sum of clay minerals. CaCO3, amorphous SiO2 and organic C form a second group, the main source of which is biota of the ocean. Zn, Cu, Ba, Mo, (V, Na) are a third group, which is supplied by both terrigenous and biogenic matter. Judging by the distribution of chemical elements and components in sediments of Site 515, this area of the Brazil Basin is characterized by the rather constant conditions of pelagic terrigenous sedimentation from upper Eocene till Holocene. Small changes in chemical composition of sediments throughout the section are linked mainly to the evolution of subaerial source provinces, changes in hydrodynamic regime, and fluctuations of the ocean level. The chemical composition of sediments from the Rio Grande Rise sites suggests the existence of three main stages of sedimentation in this area. The first stage is the initial period of sediment accumulation on basalts at the beginning of the Late Cretaceous. Then followed sedimentary conditions notable for their sharp changes in chemical composition and type. Beginning in the middle Eocene and persisting into the Holocene, stable conditions of sedimentation characterize a third stage, represented by the formation of approximately 700 m of nannofossil oozes of rather monotonous chemical composition.

(Appendix B) Carbonate fraction geochemistry at DSDP Hole 72-516F

This paper presents data on trace elements (Sr, Mg, Na, K, Mn, Fe, Ni, Cr) and isotopes (13C, 18O) on the carbonate fraction of bulk sediments from the Coniacian to Paleocene samples of Hole 516F. Relationships of trace elements to mineralogy and stratigraphic position are discussed at length, with special emphasis on 1) the differences between Hole 516F and other oceanic sites, and 2) the transitions observed at the Cretaceous/Tertiary boundary. Isotope data are compared to those obtained in other localities of the same age. The sections show the same major 13C variations at the Cretaceous/Tertiary boundary, indicating that this event is a planetary phenomenon.

(Table 1) Major and trace elements of basalts at DSDP Hole 72-516F

The geochemistry of basalts recovered during Leg 72 is described with emphasis on trace elements. Only Hole 516F penetrated basement; the basalts recovered are plagioclase-phyric and olivine-phyric and pervasively altered. Chemically, the basalts from Hole 516F are rather uniform in composition. However, four distinct geochemical units can be recognized, although the chemistry of two of the units appears to be controlled by chemical mobility associated with alteration. The two less-altered units cannot be related by fractional crystallization processes. Hole 516F basalts have a trace element chemistry characteristic of T-type mid-ocean ridge basalt; rare-earth element patterns (as indicated by Ce/Y ratios) are mildly fractionated flight rare-earth element enriched), and a number of incompatible element ratios are close to chondritic.

Compressional and shear wave velocities and elastic constants at DSDP Leg 59 Holes

Prior to the Deep Sea Drilling Project the composition of the oceanic crust could only be inferred from seismic-refraction and gravity data and the recovery of a wide variety of dredged rocks. Through the success of the Deep Sea Drilling Project, it is now clear that the top of oceanic Layer 2 usually consists of basalt. Several laboratory studies (e.g., Fox et al., 1972; Christensen and Shaw, 1970; Hyndman and Drury, 1976) have demonstrated that the seismic velocities of oceanic basalt are similar to velocities reported from refraction studies of Layer 2 and that the variability in Layer 2 velocities has many causes, the most important being fracturing and sea-floor alteration produced by the interaction of basalt and sea water (Christensen and Salisbury, 1973). To date, most reported measurements of velocities in oceanic basalts are from samples obtained from the main ocean basins. With the exception of an earlier study of velocities and related elastic properties of a suite of rocks from DSDP Sites 292, 293, 294, and 296 located in the Philippine Sea (Christensen et al., 1975; Fountain et al., 1975), elastic properties have not been determined for oceanic rocks from marginal basins. In this chapter compressional- and shear-wave velocities and elastic constants are reported at elevated confining pressures for basalt and volcanic breccias from Holes 447A, 448, and 448A.