How a soybean plant develops,1985.

This revised special report from the Iowa State University Cooperative Extension Service, no. 53. is designed to aid those involved in soybean production to more fully understand how the soybean plant develops. The content is both basic and applied. The basic information explains soybean growth and development through one life cycle. Management guides pinpoint practices needed for optimum plant growth and production.

Ma Tkoulhass El Mamak ; Ma Tkoulhass El Mamak / Simon Ohayon et Hazar Cohen, duo voc. [acc. instr.]

[Traditions. Afrique du Nord. Maroc]

Aspectes econòmics de l'evolució del sistema públic d'ensenyament superior a Catalunya, 1985-1992

L'educació superior espanyola ha sofert un procés d'expansió generalitzat a partir de la segona meitat de la decada deis vuitanta. Malgrat aixo, aquesta expansió no pot ser analitzada conjuntament, ates que durant el mateix període es fan efectives les transferencies de competencies en materia d'educació a set comunitats autonomes que comencen a dur a terme polítiques universitaries no sempre concurrents. En aquest article abordarem el model catala d'expansió úniversitaria i el seu finançament, fent emfasi en els problemes derivats dé l'expansió i les seves possibles solucions. Per fer-ho, utilitzarem la següent estructura: en primer lloc, en l'apartat 2 es descriuen els elements basics del procés d'expansió (especialment la creació de les cinc noves universitats) i la situació resultant tal i com es presenta en l'actualitat. Sense aquestes descripcibns no cobrarien sentit les analisis més específiques sobre el finançament, que es presenten en els apartats 3 i 4.

Chlordane Contamination Study of the Cedar River, Cedar Rapids, Iowa, Spring-Summer 1985

This report from the University Hygienic Laboratory contains the results of a chlordane study of the Cedar River taken in the spring and summer of 1985 after it was discovered from a routine fish tissue monitoring program in Iowa that it contained levels of chlordane in excess of the FDA action level.

Underseal Evaluation Project: Poweshiek County I-80 Near Milepost 189.5, Eastbound Roadway, MLR-85-10, 1985

The purpose of this project was to determine the optimal hole pattern needed for undersealing work, and also to determine if it is feasible to underseal a roadway with existing longitudinal subdrains without plugging the subdrain system. At the test site the hole pattern had little effect on the grout distribution. It was found that the hole pattern, to be effective, must locate existing voids and that holes must extend at least 2 in. (5 cm) below the underside of the pavement. It appeared that pavements can be undersealed without significant damage to the existing subdrains, but special care is needed to assure that excess grout is not injected into the drainage system. Recommendations are made concerning the hole pattern, grout efflux time, and procedures for minimizing the risk of plugging the subdrains with grout.

A Sufficiency Rating System for Secondary Roads in Iowa, HR-264, Volume I, 1985

County engineers in Iowa face the dual problems of rapidly escalating costs and a decreasing rate of growth of revenues. Various priority systems are in use, ranking projects for inclusion in road improvement programs, but they generally have weaknesses when used to compare one project with another in a different location. The sufficiency rating system has proven to be a useful tool in developing a priority list of projects for primary road systems, but there are none currently in use for secondary road systems. The research reported here was undertaken to develop a sufficiency rating system which could be used for secondary roads in Iowa and to produce the necessary forms and instructions to aid county engineering personnel in their efforts to complete the ratings for roads within their county.

Strengthening of Existing Single Span Steel Beam and Concrete Deck Bridges, HR-238, Part II, 1985

The unifying objective of Phases I and II of this study was to determine the feasibility of the post-tensioning strengthening method and to implement the technique on two composite bridges in Iowa. Following completion of these two phases, Phase III was undertaken and is documented in this report. The basic objectives of Phase III were further monitoring bridge behavior (both during and after post-tensioning) and developing a practical design methodology for designing the strengthening system under investigation. Specific objectives were: to develop strain and force transducers to facilitate the collection of field data; to investigate further the existence and effects of the end restraint on the post-tensioning process; to determine the amount of post-tensioning force loss that occurred during the time between the initial testing and the retesting of the existing bridges; to determine the significance of any temporary temperature-induced post-tensioning force change; and to develop a simplified design methodology that would incorporate various variables such as span length, angle-of-skew, beam spacing, and concrete strength. Experimental field results obtained during Phases II and III were compared to the theoretical results and to each other. Conclusions from this research are as follows: (1) Strengthening single-span composite bridges by post-tensioning is a viable, economical strengthening technique. (2) Behavior of both bridges was similar to the behavior observed from the bridges during field tests conducted under Phase II. (3) The strain transducers were very accurate at measuring mid-span strain. (4) The force transducers gave excellent results under laboratory conditions, but were found to be less effective when used in actual bridge tests. (5) Loss of post-tensioning force due to temperature effects in any particular steel beam post-tensioning tendon system were found to be small. (6) Loss of post-tensioning force over a two-year period was minimal. (7) Significant end restraint was measured in both bridges, caused primarily by reinforcing steel being continuous from the deck into the abutments. This end restraint reduced the effectiveness of the post-tensioning but also reduced midspan strains due to truck loadings. (8) The SAP IV finite element model is capable of accurately modeling the behavior of a post-tensioned bridge, if guardrails and end restraints are included in the model. (9) Post-tensioning distribution should be separated into distributions for the axial force and moment components of an eccentric post-tensioning force. (10) Skews of 45 deg or less have a minor influence on post-tensioning distribution. (11) For typical Iowa three-beam and four-beam composite bridges, simple regression-derived formulas for force and moment fractions can be used to estimate post-tensioning distribution at midspan. At other locations, a simple linear interpolation gives approximately correct results. (12) A simple analytical model can accurately estimate the flexural strength of an isolated post-tensioned composite beam.

Design Manual for Strengthening Single-Span Composite Bridges by Post-Tensioning Part 3, HR-238, 1985

The authors have post-tensioned and monitored two Iowa bridges and have field tested the post-tensioning of a composite bridge in Florida. In order to provide the practical post-tensioning distribution factors given in this manual, the authors developed a finite element model of a composite bridge and checked the model against a one-half scale laboratory bridge and two actual composite bridges, one of which had a 45 deg skew. Following a brief discussion of this background research, this manual explains the use of elastic, composite beam and bridge section properties, the distribution fractions for symmetrically post-tensioned exterior beams, and a method for computing the strength of a post-tensioned beam. Also included is a design example for a typical, 51.25-ft (15.62-m) span, four-beam composite bridge. Moments for Iowa Department of Transportation rating trucks, H 20 and HS 20 trucks, have been tabulated for design convenience and are included in the appendix.