Polishing for glass ceramics: Which protocol?

Purpose: The execution of adjustments on ceramic restorations is sometimes necessary for either correction of occlusion and/or inadequate contours or esthetical improvements. Clinically, the surfaces undergo weariness through fine grinding diamond burs which remove the superficial glazing layer. Several materials for ceramic polishing have been used in an attempt to reach a satisfactory surface smoothness. The aim of this study was to perform a literature review on different polishing protocols of several dental ceramics. Study selection: This is a literature review performed through scientific articles published between 2004 and 2012, indexed in MEDLINE, PubMed and Scielo databases. The study selected and analyzed a total of 20 relevant articles that evaluated different types of ceramics, polishing treatment and surface roughness.Results: After an extensive literature review, this study observed: 1 - after the rupture of the glazing layer due to the adjustments of the restorations, the best choice for the polishing of the surface will depend on the type of ceramics used; 2 - glazing procedure provide excellent results regarding to the superficial smoothness; however, if reglazing is impossible, either abrasive rubber cups/points or sandpaper discs followed by the use of diamond polishing pastes results in a satisfactory superficial smoothness; 3 - clinical studies that take into account the behavior of the protocols polishing are scarce and should be encouraged; 4 - the large number of variables influence the final outcome of polishing should be considered. Conclusions: The necessity in standardization of methodologies to enable a comparison among researches. (c) 2014 Japan Prosthodontic Society. Published by Elsevier Ireland. All rights reserved.

Estudo para a implementação de um sistema de desbaste de cobre para manufatura de placas de circuito impresso

This paper presents a study on the development of a manufacturing system of printed circuit boards through copper milling. An advantage of this system is the replacement of chemical processes by physical process presenting a sustainable solution. The paper uses programs that will generate G-code needed to establish the coordinates where the milling forms the tracks. After obtaining the code, it will be transformed into steps that will be sent through the serial port to the microcontroller and the serial communication control will be in software. After obtaining information the microcontroller will execute the movement of the stepper motors through their drivers, H-bridge, the microcontroller also drives the spindle motor responsible for rotating the grinding tool, using a driver with a optocoupler and TRIAC

Um estudo sobre a preparação metalográfica da liga de aluminio AA7075-T6

The increasing technological innovation and demand for materials with better properties boosts research into new materials and new alloys. To do so, aluminum alloys are being developed, among them the AA7075-T6, having many applications in aerospace and military industries, machinery and equipment, molds for plastic injection and structures. To study and understand the properties, characteristics and especially the microstructure of the material, the metallographic preparation is essential. This paper presents new methodologies to achieve the metallography of samples of scrap alloy AA7075-T6, with emphasis on methods of polishing. For the five samples, the best results were those with specific grinding, the samples only going down on the sander. For polishing, the most effective method so far has been using the polishing cloth 16.3, of ATM enterprise, solution of diamond 3 μm, solution of diamond 1 μm, and colloidal solution of OP-S. For the etching, the reactive agent used was phosphoric acid (H3PO4) 85% P.A., as 90% in the proportion of distilled water to 10% acid. The best results were obtained in the attacks of 300 and 240 seconds, revealing the grain boundaries in most areas. Methodologies need more studies and more tests, but the results have proved to be satisfactory

Lixamento do Pinus elliotti com carbeto de silício e óxido de aluminio

The Sanding is a complex process involving many variables that affect the quality of the part produced, working mainly in the timber industry in the production of panels (MDF, MDP, HDF, etc...) and furniture. However, these industries use the sanding process empirically, not optimizing it. The aim of this study was to compare the behavior of sandpaper white aluminum oxide (OA-white) and Black silicon carbide (SiC-black), analyzing variables in the process as: strength, power, emission, vibration, wear particle size of sanding, and its consequences on the surface finish of the workpiece. Made the process of plane grinding samples of Pinus elliottii, processed in parallel to the fibers, which were sanded with sandpaper grain OA white and black 3-SiC abrasive conditions (new, moderately eroded and severely eroded) grain sizes in 3 (80, 100, and 120 mesh). 6 replicates was performed for each condition tested. Each trial was captured output variables of the sanding process: strength, power, emission and vibration. With two stages totaling 108 trials. After the sanded samples, it has the same surface quality by raising the surface roughness Ra. Through experiment, it can be concluded that abrasives OA-white tended to have higher strength, power, emissions and less vibration in the sanding process, compared to the SiC-black. However, surface finish exhibited similar to the particle size of 80 to 100 mesh, worn abrasive conditions. However, the particle size of 120 mesh, obtained by the roughness of sandpaper OA-bank was higher compared to SiC-black to all conditions of sandpaper due to its toughness

Um Estudo de caso sobre a fabricação de engrenagens

Human evolution has always been linked to personal or group needs. This statement is based on observations of the day to day. With time, we can now choose from among many excellent techniques and materials that can be employed in the construction of this part of the machinery so important to the functionality of machines and equipment. When we look at a machine, we see that this is usually designed by combining a set of pre-determined in your project. Among the many pieces that we can highlight one of them is of fundamental importance, the gear. Gears are an example of the mechanical devices used by the older man, and are currently the most important components in the transmission technique. This is responsible for transmitting rotary motion from one shaft to another. Gears are one of the best among the various means available for the transmission of motion. Gears are the most important components of modern technique of transmission. The main purpose of a transmission gear is precisely transmit torque and speed. The requirements have increased significantly due to pollution and energy conservation. Nowadays, gear transmissions are required to transmit high strength through all his life together with the high demand on performance and sound properties. An optimal design for the gear you need a set of the most modern fabrication machines and cutting tools. In the following work is studied on the manufacture of gears, making the monitoring of a case study of the try out the installation of a gear grinding machine

Efeito do Estrôncio (Sr) no tratamento de modificação do eutético da liga Al-1%Si

This study aimed to analyze the cooling curves, micro and macrograph alloy Al-1 %Si without the addition of strontium modifier and with the addition of the same. One of the ways of improving mechanical properties of alloy Al -Si is through the modification process. For the experiments two billets of the alloy Al-1%Si cast iron mold in a billet with addition of 0.02% strontium by weight, and the other billet without the addition of modifier were fused. In the solidification process of billet temperature was monitored and recorded every second for later plotting in Origin 8 program and analyzes the cooling curves obtained. The billets were cut and passed by grinding and polishing to perform the macrograph and micrographs. The results concerning the macrograph indicated that billet without the addition of Strontium particle size obtained was more refined than the billet where the strontium modifier was added. Regarding the micrograph, photos stemmed from the optical microscope didn´t show the expected modification effect by the addition of Strontium. This suggests that the low amount of silicon (1 %) present in the alloy used in this study interfered in the change process, because according to the literature review, Strontium 0.022 % by weight is sufficient to fully modify an alloy with 7% Silicon. The results from the cooling curve showed that both the eutectic temperature and the solidification time remained unchanged with the addition of strontium

Processo de esmerilhamento, polimento e caracterização de um Shear Plate

Shearplate is an optical glass plate having two flat surfaces and a small angle between them. The use of a high quality shear plate is essential to implement shear interferometric technique . The shear interferometry is a technique used to evaluate the light beam collimation. In order to guarantee the shearplate quality , the complete manufacturing process must be thoroughly monitored. In the manufacturing process, the first step consisted of the glass selection. The selected glass has been submitted to the process of cutting, gluing, chamfering, grinding and polishing. Each phase has been strictly monitored. The quality of the final result depends extremely on an appropriate starting condition, which arises from the grinding process, as the polishing process only recovers the brightness of the part, acting on a small scale on the wearing off of the part, as well as not changing the structured obtained in the grinding process. Respecting all stages of the manufacturing process, the quality of the part has evolved to a good result. The best result obtained showed PV distance of 162 nm, slightly less than λ / 4. This result is significant because the dimensions of the piece with respect to the dimensions of the polisher what interferes directly in the results. The closer are the dimensions of piece and the dimensions of the polisher, the greater the difficulty in controlling the propagation of errors

Crescimeno de apatita na superfície da liga Ti-7, 5Mo empregando tratamento higrotérmico

The objective of the present work was to evaluate surface of experimental alloy Ti-7.5Mo after hydrothermal treatment. Ingots were obtained in arc melting furnace under an argon atmosphere and then homogenized under vacuum at 1100ºC for 86.4 ks to eliminate chemical segregation and after cold worked discs were cutting and grinding. For surface treatment, samples were immersed in a container with NaOH aqueous solution 5M, autoclaved, washed with distilled water. Followed, samples were heat treated and they were soaking in 5xSBF to form an apatite layer on the surface. Surfaces were investigated by, scanning electron microscopy, X-Rays powder diffraction, atomic force microscopy and contact angle, in order to evaluate the wettability of the alloy surface. The results were compared with our previous studies using the group of chemical surface treatments and results shows better condition is 120 minutes in the autoclave

Uso de composto de poda de árvore e lodo de esgoto como substratos na formação de mudas de sangra d'água (Croton urucurana Baill.) irrigadas com três lâminas de água

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Monitoramento da condição da ferramenta de dressagem usando sinais de vibração e modelos neurais

Pós-graduação em Engenharia Elétrica - FEB

Análise do comportamento do desgaste de dressadores de ponta única confeccionados com diamantes naturais e sintético piramidais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determinação de chumbo em tubos de raios catódicos e em solo contaminado por espectrometria de absorção atômica

Pós-graduação em Ciência dos Materiais - FEIS

A influência da temperatura na secagem forçada da matéria-prima cerâmica da Formação Corumbataí na região do Polo de Santa Gertrudes (SP)

Pós-graduação em Geociências e Meio Ambiente - IGCE

Procedência da cocaína e maconha definida por isótopos estáveis

Objectives: the aim of this work was to define the range of possible values for each isotope of carbon-13 and nitrogen-15 for cocaine and marijuana seized in Botucatu-SP, with the intention of distinguishing the geographical origin of the drug. Materials and Methods: samples of marijuana and cocaine were collected at the time of incineration. Then, at the Stable Isotope Center from São Paulo State University in Botucatu, São Paulo, Brazil, samples of marijuana were subjected to the drying process and subsequent grinding. Samples of cocaine were not submitted to the processes of drying and grinding because they were already in adequate granulometry. Subsequently, the samples of both drugs were weighed in accordance with the standards for carbon-13 and nitrogen-15. Lastly, CO2 and N2 gases were obtained from the samples through the elemental analyzer. They were then analyzed in a mass spectrometer to obtain values of δ13C and δ15N in ‰. Results and Discussion: the results of marijuana allowed for comparison with regions of Queensland, Australia, according to the range of δ13C between -29.9 ‰ and -29.3 ‰ and δ15N range from 4.1 ‰ to 5.8 ‰. The results were also consistent with those of the state of Pará, Brazil, where the values of δ13C and δ15N were -30.3 ± 0.7 ‰ and 5.0 ± 1.3 ‰, respectively. Also the results were in accordance with those from the state of Mato Grosso do Sul, Brazil, in which δ13C values varied by -28.7 ± 1.3 ‰, and δ15N values varied by 6.6 ± 1.1 ‰, respectively. In both regions, the samples identified as being from Pará and Mato Grosso do Sul showed an overlap. In addition, the results fitted with data from the state of Maranhão, in which the values of δ13C and δ15 N were -28.8 ± 1.6 ‰ and 2.9 ± 2.5 ‰, respectively. In the case of cocaine, the present study could not be related to the results from the literature. One possible explanation may be related to the non-purification of ...

Utilização da cinza de folha de cana-de-açúcar como material pozolânico em matrizes cimentantes

Pós-graduação em Engenharia Civil - FEIS