Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

Relação entre mercado de terras, crescimento econômico e insegurança fundiária explicada por um modelo a "geração imbricada"

In this paper, we analyze the relationship between the land market failures and the economic growth in Brazil, starting from an overlapping model including two sectors: agricultural and industrial. The land is both a specific factor for agriculture and an asset that can be substituted to the capital used in industry. The trade-off between land and capital holding depends, among other factors, on the transaction costs on the land market. These costs result from land insecurity and generate a decrease in the land price that favors capital accumulation. Two assumptions follow from our model: one the one hand, land insecurity has a negative effect on the land price; one the other hand it has a positive effect on economic growth. These two hypotheses are tested on panel data for Brazilian Federation. The econometric results do not reject our hypothesis.

Shop-floor narratives : how six workers and a researcher describe learning activities

I am a part-time graduate student who works in industry. This study is my narrative about how six workers and I describe shop-floor learning activities, that is learning activities that occur where work is done, outside a classroom. Because this study is narrative inquiry, you wilileam about me, the narrator, more than you would in a more conventional study. This is a common approach in narrative inquiry and it is important because my intentions shape the way that I tell these six workers' stories. I developed a typology of learning activities by synthesizing various theoretical frameworks. This typology categorizes shop-floor learning activities into five types: onthe- job training, participative learning, educational advertising, incidental learning, and self-directed learning. Although learning can occur in each of these activities in isolation, it is often comprised of a mixture of these activities. The literature review contains a number of cases that have been developed from situations described in the literature. These cases are here to make the similarities and differences between the types of learning activities that they represent more understandable to the reader and to ground the typology in practice as well as in theory. The findings are presented as reader's theatre, a dramatic presentation of these workers' narratives. The workers tell us that learning involves "being shown," and if this is not done properly they "learn the hard way." I found that many of their best case lean1ing activities involved on-the-job training, participative learning, incidentalleaming, and self-directed learning. Worst case examples were typically lacking in properly designed and delivered participative learning activities and to a lesser degree lacking carefully planned and delivered on-the-job training activities. Included are two reflective chapters that describe two cases: Learning "Engels" (English), and Learning to Write. In these chapters you will read about how I came to see that my own shop-floor learning-learning to write this thesis-could be enhanced through participative learning activities. I came to see my thesis supervisor as not only my instructor who directed and judged my learning activities, but also as a more experienced researcher who was there to participate in this process with me and to help me begin to enter the research community. Shop-floor learning involves learners and educators participating in multistranded learning activities, which require an organizational factor of careful planning and delivery. As with learning activities, which can be multi-stranded, so too, there can be multiple orientations to learning on the shop floor. In our stories, you will see that these six workers and I didn't exhibit just one orientation to learning in our stories. Our stories demonstrate that we could be behaviorist and cognitivist and humanist and social learners and constructivist in our orientation to learning. Our stories show that learning is complex and involves multiple strands, orientations, and factors. Our stories show that learning narratives capture the essence of learning-the learners, the educators, the learning activities, the organizational factors, and the learning orientations. Learning narratives can help learners and educators make sense of shop-floor learning.

Active nuclear import and cytoplasmic retention of activation-induced deaminase

The enzyme activation-induced deaminase (AID) triggers antibody diversification in B cells by catalyzing deamination and consequently mutation of immunoglobulin genes. To minimize off-target deamination, AID is restrained by several regulatory mechanisms including nuclear exclusion, thought to be mediated exclusively by active nuclear export. Here we identify two other mechanisms involved in controlling AID subcellular localization. AID is unable to passively diffuse into the nucleus, despite its small size, and its nuclear entry requires active import mediated by a conformational nuclear localization signal. We also identify in its C terminus a determinant for AID cytoplasmic retention, which hampers diffusion to the nucleus, competes with nuclear import and is crucial for maintaining the predominantly cytoplasmic localization of AID in steady-state conditions. Blocking nuclear import alters the balance between these processes in favor of cytoplasmic retention, resulting in reduced isotype class switching.

Un formalisme pour la traçabilité des transformations

Dans le développement logiciel en industrie, les documents de spécification jouent un rôle important pour la communication entre les analystes et les développeurs. Cependant, avec le temps, les changements de personel et les échéances toujours plus courtes, ces documents sont souvent obsolètes ou incohérents avec l'état effectif du système, i.e., son code source. Pourtant, il est nécessaire que les composants du système logiciel soient conservés à jour et cohérents avec leurs documents de spécifications pour faciliter leur développement et maintenance et, ainsi, pour en réduire les coûts. Maintenir la cohérence entre spécification et code source nécessite de pouvoir représenter les changements sur les uns et les autres et de pouvoir appliquer ces changements de manière cohérente et automatique. Nous proposons une solution permettant de décrire une représentation d'un logiciel ainsi qu'un formalisme mathématique permettant de décrire et de manipuler l'évolution des composants de ces représentations. Le formalisme est basé sur les triplets de Hoare pour représenter les transformations et sur la théorie des groupes et des homomorphismes de groupes pour manipuler ces transformations et permettrent leur application sur les différentes représentations du système. Nous illustrons notre formalisme sur deux représentations d'un système logiciel : PADL, une représentation architecturale de haut niveau (semblable à UML), et JCT, un arbre de syntaxe abstrait basé sur Java. Nous définissons également des transformations représentant l'évolution de ces représentations et la transposition permettant de reporter les transformations d'une représentation sur l'autre. Enfin, nous avons développé et décrivons brièvement une implémentation de notre illustration, un plugiciel pour l'IDE Eclipse détectant les transformations effectuées sur le code par les développeurs et un générateur de code pour l'intégration de nouvelles représentations dans l'implémentation.

Sélection et polymorphisme chez des grenouilles mimétiques du Pérou (Dendrobatidae)

La diversification des signaux aposématiques dans un cadre de mimétisme müllérien est un phénomène intrigant. Alors que la théorie relative à l'aposématisme et au mimétisme suggère l'évolution vers un signal aposématique unique, d'impressionnantes variations peuvent être observées entre les populations, et cela à petite échelle spatiale. Il a été supposé que la variation spatiale des pressions de sélection engendrées par différents prédateurs puisse être à l'origine de ce phénomène. Afin de tester cette hypothèse, nous avons étudié la transition entre deux systèmes géographiques caractérisés par des patrons aposématiques distincts chez des grenouilles mimétiques et toxiques du nord du Pérou (Dendrobatidae) en combinant les outils de génétique des populations aux outils écologiques. Dans chacun de ces systèmes, Ranitomeya imitator vit en sympatrie avec R. ventrimaculata ou R. variabilis. Il s'agit du principal exemple empirique suggérant que dans un cadre de mimétisme müllérien, il n'y a pas convergence des signaux aposématiques des deux espèces, mais plutôt convergence unidirectionnelle où R. imitator, étant polymorphe, imite des espèces monomorphes avec lesquelles elle est sympatrique. Premièrement, les résultats réfutent les prémisses qui suggèrent que R. imitator converge vers le signal aposématique d’une autre espèce. La haute similarité génétique entre les espèces modèles suggère qu'elles ont divergé plus récemment que les populations de R. imitator ou qu'elles sont encore connectées par du flux génique. Ces résultats indiquent que ces espèces ont été identifiées à tort comme des espèces différentes. De fait, l'identification de l'espèce imitatrice basée sur la variabilité phénotypique est invalidée dans ce système puisque R. imitator et R. variabilis/ventrimaculata démontrent la même variabilité. Deuxièmement, nos résultats démontrent que la prédation varie spatialement, autant en intensité qu'en direction, créant ainsi un paysage hétérogène de pressions de sélection. Ainsi, de fortes pressions de prédation stabilisatrice permettent le maintien de l'organisation géographique de différents signaux aposématiques et expliquent l'uniformité de ces signaux ainsi que les relations mimétiques. Par contre, le relâchement temporaire des pressions de prédation permet l'apparition de nouveaux phénotypes aposématiques via les processus évolutifs neutres, conduisant à un haut polymorphisme au niveau de ces populations. L'interaction de ces modes sélectifs nous a permis de démontrer pour la première fois comment la théorie évolutive de Wright (shifting balance theory) permet la diversification adaptative dans un système naturel. Pour conclure, cette étude a permis de mettre en évidence à quel point les systèmes de mimétisme müllérien peuvent être dynamiques. L'alternance spatiale entre les processus évolutifs neutres et la sélection naturelle permet l'émergence de nouveaux phénotypes aposématiques à une échelle locale, ainsi que l'apparition d'une organisation géographique des signaux d'avertissement et des relations de mimétisme müllérien.

Développement de nouveaux polymères amphiphiles comme floculants versatiles pour le traitement de l’eau issue de l’industrie pétrolière

Les polymères hydrosolubles sont utilisés dans diverses industries pour permettre la floculation, soit une séparation solide-liquide de particules présentes en suspension colloïdale. Afin de réduire les impacts environnementaux de l’exploitation des sables bitumineux en Alberta, l’industrie est à la recherche de nouveaux moyens et procédés pour traiter les résidus miniers permettant de séparer les matières solides et de récupérer l’eau. L’objectif des travaux présentés est d’améliorer la floculation, la densification et la déshydratation de ces résidus miniers aqueux par de nouveaux polymères synthétiques. Des homopolymères d’acrylamide de différentes masses molaires ont été synthétisés pour étudier l’influence de la masse molaire sur l’efficacité de floculation. Le taux initial de sédimentation (TIS) est le paramètre qui fut utilisé afin de comparer l’efficacité de floculation des différents polymères. Il a été possible de confirmer l’importance de la masse molaire sur l’efficacité de floculation et de déterminer une masse molaire minimale d’environ 6 MDa pour des polyacrylamides, afin d’obtenir l’efficacité de floculation maximale de suspensions colloïdales principalement composées de kaolin. Afin d’étudier l’effet des charges sur l’efficacité de floculation, des polymères anioniques et cationiques ont été synthétisés. Une série de copolymères d’acrylamide et d’acide acrylique ont été synthétisés comme polymères anioniques et deux séries de copolymères ont été synthétisés comme polymères cationiques, soit des copolymères d’acrylamide et de chlorure de diallyldiméthylammonium et des copolymères de 4-vinyl pyridine et de 1-méthyl-4-vinyl pyridinium. Il a été démontré que les charges anioniques des polymères avaient peu d’influence sur l’efficacité de floculation et que leur comportement en présence de sels était différent de ce que prévoyait la littérature. Il a aussi été démontré que les charges cationiques des polymères n’améliorent pas l’efficacité de floculation. Par la suite, des séries de copolymères amphiphiles, avec des monomères d’acrylamide, de N-alkylacrylamides et d’acrylonitrile, ont été synthétisés, pour étudier l’effet du caractère amphiphile sur la déshydratation des résidus miniers. Le pourcentage de déshydratation nette est le paramètre qui fut utilisé afin de comparer l’efficacité de déshydratation des différents polymères. Il a été possible de développer des copolymères amphiphiles qui améliorent l’efficacité de déshydratation par rapport à des homopolymères d’acrylamide. Il ne fut pas possible de déterminer une tendance entre la balance hydrophile/hydrophobe des copolymères amphiphiles et l’efficacité de déshydratation.

Spray Pyrolysed Zinc Oxide Thin Films : Effects of Doping and Ion Beam Irradiation

In recent years scientists have made rapid and significant advances in the field of semiconductor physics. One of the most important fields of current interest in materials science is the fundamental aspects and applications of conducting transparent oxide thin films (TCO). The characteristic properties of such coatings are low electrical resistivity and high transparency in the visible region. The first semitransparent and electrically conducting CdO film was reported as early as in 1907 [1]. Though early work on these films was performed out of purely scientific interest, substantial technological advances in such films were made after 1940. The technological interest in the study of transparent semiconducting films was generated mainly due to the potential applications of these materials both in industry and research. Such films demonstrated their utility as transparent electrical heaters for windscreens in the aircraft industry. However, during the last decade, these conducting transparent films have been widely used in a variety of other applications such as gas sensors [2], solar cells [3], heat reflectors [4], light emitting devices [5] and laser damage resistant coatings in high power laser technology [6]. Just a few materials dominate the current TCO industry and the two dominant markets for TCO’s are in architectural applications and flat panel displays. The architectural use of TCO is for energy efficient windows. Fluorine doped tin oxide (FTO), deposited using a pyrolysis process is the TCO usually finds maximum application. SnO2 also finds application ad coatings for windows, which are efficient in preventing radiative heat loss, due to low emissivity (0.16). Pyrolitic tin oxide is used in PV modules, touch screens and plasma displays. However indium tin oxide (ITO) is mostly used in the majority of flat panel display (FPD) applications. In FPDs, the basic function of ITO is as transparent electrodes. The volume of FPD’s produced, and hence the volume of ITO coatings produced, continues to grow rapidly. But the current increase in the cost of indium and the scarcity of this material created the difficulty in obtaining low cost TCOs. Hence search for alternative TCO materials has been a topic of active research for the last few decades. This resulted in the development of binary materials like ZnO, SnO2, CdO and ternary materials like II Zn2SnO4, CdSb2O6:Y, ZnSO3, GaInO3 etc. The use of multicomponent oxide materials makes it possible to have TCO films suitable for specialized applications because by altering their chemical compositions, one can control the electrical, optical, chemical and physical properties. But the advantages of using binary materials are the easiness to control the chemical compositions and depositions conditions. Recently, there were reports claiming the deposition of CdO:In films with a resistivity of the order of 10-5 ohm cm for flat panel displays and solar cells. However they find limited use because of Cd-Toxicity. In this regard, ZnO films developed in 1980s, are very useful as these use Zn, an abundant, inexpensive and nontoxic material. Resistivity of this material is still not very low, but can be reduced through doping with group-III elements like In, Al or Ga or with F [6]. Hence there is a great interest in ZnO as an alternative of ITO. In the present study, we prepared and characterized transparent and conducting ZnO thin films, using a cost effective technique viz Chemical Spray Pyrolysis (CSP). This technique is also suitable for large area film deposition. It involves spraying a solution, (usually aqueous) containing soluble salts of the constituents of the desired compound, onto a heated substrate.

L-glutaminase production by marine fungi

This study presents the L-Glutaminase Production by Marine Fungi. Enzymes are involved in all aspects of biochemical conversion from the simple enzyme or fermentation conversion to the complex techniques in genetic engineering. Enzyme industry is one among the major industries of the world and there exists a great market for enzymes in general. Food industry is recognized as the largest consumer for commercial enzymes (Lon sane and Ramakrishna, 1989). In industry, enzymes are frequently used for process improvement, for instance to enable the utilization of new types of raw materials or for improving the physical properties of a material so that it can be more easily processed. They are the focal point of biotechnological processe. The marine biosphere is one of the richest of the earth's innumerable habitats, yet is one of the least well characterized. The marine biosphere covers more than two third of the world's surface, our knowledge of marine microorganisms, in particular fungi, is still very limited (Molitoris and Schumann, 1986). The results obtained in the present study the following conclusions are drawn. Beauveria bassiana isolated form marine sediment has immense potential as an Industrial organism for production of L-glutaminase as an extracellular enzyme employing either submerged fermentnation or solid state fermentation

Investigations on broadband planar monopole and slot radiators and their suitability for UWB applications

In recent years, there is a visible trend for products/services which demand seamless integration of cellular networks, WLANs and WPANs. This is a strong indication for the inclusion of high speed short range wireless technology in future applications. In this context UWB radio has a significant role to play as an extension/complement to existing cellular/access technology. In the present work, we have investigated two major types of wide band planar antennas: Monopole and Slot. Four novel compact broadband antennas, suitable for poratble applications, are designed and characterized, namely 1. Elliptical monopole 2. Inverted cone monopole 3. Koch fractal slot 4. Wide band slot The performance of these designs have been studied using standard simulation tools used in industry/academia and they have been experimentally verified. Antenna design guidelines are also deduced by accounting the resonances in each structure. In addition to having compact sized, high efficiency and broad bandwidth antennas, one of the major criterion in the design of impulse-UWB systems have been the transmission of narrow band pulses with minimum distortion. The key challenge is not only to design a broad band antenna with constant and stable gain but to maintain a flat group delay or linear phase response in the frequency domain or excellent transient response in time domain. One of the major contributions of the thesis lies in the analysis of the frequency and time-domain response of the designed UWB antennas to confirm their suitability for portable pulsed-UWB systems. Techniques to avoid narrowband interference by engraving narrow slot resonators on the antenna is also proposed and their effect on a nano-second pulse have been investigated.

Development of Free Space Method for Material Characterisation and GPR Study & A Case Study on Biological Samples

The thesis mainly focuses on material characterization in different environments: freely available samples taken in planar fonn, biological samples available in small quantities and buried objects.Free space method, finds many applications in the fields of industry, medicine and communication. As it is a non-contact method, it can be employed for monitoring the electrical properties of materials moving through a conveyor belt in real time. Also, measurement on such systems at high temperature is possible. NID theory can be applied to the characterization of thin films. Dielectric properties of thin films deposited on any dielectric substrate can be determined. ln chemical industry, the stages of a chemical reaction can be monitored online. Online monitoring will be more efficient as it saves time and avoids risk of sample collection.Dielectric contrast is one of the main factors, which decides the detectability of a system. lt could be noted that the two dielectric objects of same dielectric constant 3.2 (s, of plastic mine) placed in a medium of dielectric constant 2.56 (er of sand) could even be detected employing the time domain analysis of the reflected signal. This type of detection finds strategic importance as it provides solution to the problem of clearance of non-metallic mines. The demining of these mines using the conventional techniques had been proved futile. The studies on the detection of voids and leakage in pipes find many applications.The determined electrical properties of tissues can be used for numerical modeling of cells, microwave imaging, SAR test etc. All these techniques need the accurate determination of dielectric constant. ln the modem world, the use of cellular and other wireless communication systems is booming up. At the same time people are concemed about the hazardous effects of microwaves on living cells. The effect is usually studied on human phantom models. The construction of the models requires the knowledge of the dielectric parameters of the various body tissues. lt is in this context that the present study gains significance. The case study on biological samples shows that the properties of normal and infected body tissues are different. Even though the change in the dielectric properties of infected samples from that of normal one may not be a clear evidence of an ailment, it is an indication of some disorder.ln medical field, the free space method may be adapted for imaging the biological samples. This method can also be used in wireless technology. Evaluation of electrical properties and attenuation of obstacles in the path of RF waves can be done using free waves. An intelligent system for controlling the power output or frequency depending on the feed back values of the attenuation may be developed.The simulation employed in GPR can be extended for the exploration of the effects due to the factors such as the different proportion of water content in the soil, the level and roughness of the soil etc on the reflected signal. This may find applications in geological explorations. ln the detection of mines, a state-of-the art technique for scanning and imaging an active mine field can be developed using GPR. The probing antenna can be attached to a robotic arm capable of three degrees of rotation and the whole detecting system can be housed in a military vehicle. In industry, a system based on the GPR principle can be developed for monitoring liquid or gas through a pipe, as pipe with and without the sample gives different reflection responses. lt may also be implemented for the online monitoring of different stages of extraction and purification of crude petroleum in a plant.Since biological samples show fluctuation in the dielectric nature with time and other physiological conditions, more investigation in this direction should be done. The infected cells at various stages of advancement and the normal cells should be analysed. The results from these comparative studies can be utilized for the detection of the onset of such diseases. Studying the properties of infected tissues at different stages, the threshold of detectability of infected cells can be determined.

Design and Development of re configurable compact cross patch antenna for switchable polarization

Antennas are necessary and vital components of communication and radar systems, but sometimes their inability to adjust to new operating scenarios can limit system performance. Reconfigurable antennas can adjust with changing system requirements or environmental conditions and provide additional levels of functionality that may result in wider instantaneous frequency bandwidths, more extensive scan volumes, and radiation patterns with more desirable side lobe distributions. Their agility and diversity created new horizons for different types of applications especially in cognitive radio, Multiple Input Multiple Output Systems, satellites and many other applications. Reconfigurable antennas satisfy the requirements for increased functionality, such as direction finding, beam steering, radar, control and command, within a confined volume. The intelligence associated with the reconfigurable antennas revolved around switching mechanisms utilized. In the present work, we have investigated frequency reconfigurable polarization diversity antennas using two methods: 1. By using low-loss, high-isolation switches such as PIN diode, the antenna can be structurally reconfigured to maintain the elements near their resonant dimensions for different frequency bands and/or polarization. 2. Secondly, the incorporation of variable capacitors or varactors, to overcome many problems faced in using switches and their biasing. The performances of these designs have been studied using standard simulation tools used in industry/academia and they have been experimentally verified. Antenna design guidelines are also deduced by accounting the resonances. One of the major contributions of the thesis lies in the analysis of the designed antennas using FDTD based numerical computation to validate their performance.

Design and development of compact printed ultra wide band antennas

In recent years, there is a visible trend for products/services which demand seamless integration of cellular networks, WLANs and WPANs. This is a strong indication for the inclusion of high speed short range wireless technology in future applications. In this context UWB radio has a significant role to play as an extension/complement to existing cellular/access technology. In the present work, three major types of ultra wide band planar antennas are investigated: Monopole and Slot. Three novel compact UWB antennas, suitable for poratble applications, are designed and characterized, namely 1) Ground modified monopole 2) Serrated monopole 3) Triangular slot The performance of these designs have been studied using standard simulation tools used in industry/academia and they have been experimentally verified. Antenna design guidelines are also deduced by accounting the resonances in each structure. In addition to having compact sized, high efficiency and broad bandwidth antennas, one of the major criterion in the design of impulse-UWB systems have been the transmission of narrow band pulses with minimum distortion. The key challenge is not only to design a broad band antenna with constant and stable gain but to maintain a flat group delay or linear phase response in the frequency domain or excellent transient response in time domain. One of the major contributions of the thesis lies in the analysis of the frequency and timedomain response of the designed UWB antennas to confirm their suitability for portable pulsed-UWB systems. Techniques to avoid narrowband interference by engraving narrow slot resonators on the antenna is also proposed and their effect on a nano-second pulse have been investigated

Fermentation Of Rice And Related Products By Bacillus Sp.

Recently’ recognition cnf immobilization ‘technology for the rapid conversion of several substrates into metabolites and repeated reuse of the biocatalysts have drawn the attention of the fermentation scientists and technologists to try these new technologies for the rapid production of pnxkmt and enhancement of the efficiencies of the systems Hence in the present study rice was selected,as a substrate since it is a rich source of starch, available and cultivated throughout the year almost in all part of our country. Rice although known for its use as a staple food in many forms as rice, idli, dosai etc., has not been used in industry extensively. However, it ii; a potential resource for’ the production of alcohol, high protein food anui for sugar and sugar syrups as it is evidenced by the few reports mentioned in the review of literature. Of the several microorganisms available, Bacillus sp, is a known candidate for the production of amylases. Hence in the present study Bacillus sp, was desired for its known efficiencies in starch conversion

Análisis económico de las vacunas 10-valente y 13-valente contra neumococo: revisión sistemática

Introducción: Las vacunas clásicamente han representado un método económico y eficaz para el control y prevención de múltiples enfermedades infecciosas. En los últimos años se han introducido nuevas vacunas contra neumococo a precios elevados, y los diferentes análisis económicos a nivel mundial de estas vacunas no muestran tendencias. El objetivo de este trabajo era resumir la evidencia existente a través de los diferentes estudios económicos evaluando las dos vacunas de segunda generación contra neumococo en la población a riesgo. Metodología: En este trabajo se realizo una revisión sistemática de la literatura en 8 bases de datos localizadas en diferentes partes del mundo y también que tuvieran literatura gris. Los artículos fueron inicialmente evaluados acorde a su titulo y resumen, posteriormente los elegidos se analizaron en su totalidad. Resultados: Se encontraron 404 artículos, de los cuales 20 fueron incluidos en el análisis final. Se encontró que la mayoría de los estudios se realizaron en áreas donde la enfermedad tiene una carga baja, como es Norte América y Europa, mientras que en los lugares del mundo donde la carga es mas alta, se realizaron pocos estudios. De igual manera se observo que la mayoría de los estudios mostraron por los menos ser costo efectivos respecto a la no vacunación, y en su totalidad las dos vacunas de segunda generación mostraron costo efectividad respecto a la vacunación con PCV-7. Los resultados de los estudios son muy heterogéneos, hasta dentro del mismo país, señalando la necesidad de guías para la conducción de este tipo de estudios. De igual manera, la mayoría de los estudios fueron financiados por farmacéuticas, mientras en un numero muy reducido por entes gubernamentales. Conclusiones: La mayoría de los estudios económicos sobre las vacunas de segunda generación contra neumococo han sido realizados en países con un alto índice de desarrollo económico y patrocinados por farmacéuticas. Dado que la mayoría de la carga de la enfermedad se encuentran en regiones con un menor nivel de desarrollo económico se deberían realizar mas en estas zonas. De igual manera, al ser la vacunación un asunto de salud publica y con un importante impacto económico los gobiernos deberían estar mas involucrados en los mismos.