Adapting mode switches into the hierarchical scheduling

Mode switches are used to partition the system’s behavior into different modes to reduce the complexity of large embedded systems. Such systems operate in multiple modes in which each one corresponds to a specific application scenario; these are called Multi-Mode Systems (MMS). A different piece of software is normally executed for each mode. At any given time, the system can be in one of the predefined modes and then be switched to another as a result of a certain condition. A mode switch mechanism (or mode change protocol) is used to shift the system from one mode to another at run-time. In this thesis we have used a hierarchical scheduling framework to implement a multi-mode system called Multi-Mode Hierarchical Scheduling Framework (MMHSF). A two-level Hierarchical Scheduling Framework (HSF) has already been implemented in an open source real-time operating system, FreeRTOS, to support temporal isolation among real-time components. The main contribution of this thesis is the extension of the HSF featuring a multimode feature with an emphasis on making minimal changes in the underlying operating system (FreeRTOS) and its HSF implementation. Our implementation uses fixed-priority preemptive scheduling at both local and global scheduling levels and idling periodic servers. It also now supports different modes of the system which can be switched at run-time. Each subsystem and task exhibit different timing attributes according to mode, and upon a Mode Change Request (MCR) the task-set and timing interfaces of the entire system (including subsystems and tasks) undergo a change. A Mode Change Protocol specifies precisely how the system-mode will be changed. However, an application may not only need to change a mode but also a different mode change protocol semantic. For example, the mode change from normal to shutdown can allow all the tasks to be completed before the mode itself is changed, while changing a mode from normal to emergency may require aborting all tasks instantly. In our work, both the system mode and the mode change protocol can be changed at run-time. We have implemented three different mode change protocols to switch from one mode to another: the Suspend/resume protocol, the Abort protocol, and the Complete protocol. These protocols increase the flexibility of the system, allowing users to select the way they want to switch to a new mode. The implementation of MMHSF is tested and evaluated on an AVR-based 32 bit board EVK1100 with an AVR32UC3A0512 micro-controller. We have tested the behavior of each system mode and for each mode change protocol. We also provide the results for the performance measures of all mode change protocols in the thesis. RESUMEN Los conmutadores de modo son usados para particionar el comportamiento del sistema en diferentes modos, reduciendo así la complejidad de grandes sistemas empotrados. Estos sistemas tienen multiples modos de operación, cada uno de ellos correspondiente a distintos escenarios y para distintas aplicaciones; son llamados Sistemas Multimodales (o en inglés “Multi-Mode Systems” o MMS). Normalmente cada modo ejecuta una parte de código distinto. En un momento dado el sistema, que está en un modo concreto, puede ser cambiado a otro modo distinto como resultado de alguna condicion impuesta previamente. Los mecanismos de cambio de modo (o protocolos de cambio de modo) son usados para mover el sistema de un modo a otro durante el tiempo de ejecución. En este trabajo se ha usado un modelo de sistema operativo para implementar un sistema multimodo llamado MMHSF, siglas en inglés correspondientes a (Multi-Mode Hierarchical Scheduling Framework). Este sistema está basado en el HSF (Hierarchical Scheduling Framework), un modelo de sistema operativo con jerarquía de dos niveles, implementado en un sistema operativo en tiempo real de libre distribución llamado FreeRTOS, capaz de permitir el aislamiento temporal entre componentes. La principal contribución de este trabajo es la ampliación del HSF convirtiendolo en un sistema multimodo realizando los cambios mínimos necesarios sobre el sistema operativo FreeRTOS y la implementación ya existente del HSF. Esta implementación usa un sistema de planificación de prioridad fija para ambos niveles de jerarquía, ocupando el tiempo entre tareas con un “modo reposo”. Además el sistema es capaz de cambiar de un modo a otro en tiempo de ejecución. Cada subsistema y tarea son capaces de tener distintos atributos de tiempo (prioridad, periodo y tiempo de ejecución) en función del modo. Bajo una demanda de cambio de modo (Mode Change Request MCR) se puede variar el set de tareas en ejecución, así como los atributos de los servidores y las tareas. Un protocolo de cambio de modo espeficica precisamente cómo será cambiado el sistema de un modo a otro. Sin embargo una aplicación puede requerir no solo un cambio de modo, sino que lo haga de una forma especifica. Por ejemplo, el cambio de modo de “normal” a “apagado” puede permitir a las tareas en ejecución ser finalizadas antes de que se complete la transición, pero sin embargo el cambio de “normal” a “emergencia” puede requerir abortar todas las tareas instantaneamente. En este trabajo ambas características, tanto el modo como el protocolo de cambio, pueden ser cambiadas en tiempo de ejecución, pero deben ser previamente definidas por el desarrollador. Han sido definidos tres protocolos de cambios: el protocolo “suspender/continuar”, protocolo “abortar” y el protocolo “completar”. Estos protocolos incrementan la flexibilidad del sistema, permitiendo al usuario seleccionar de que forma quieren cambiar hacia el nuevo modo. La implementación del MMHSF ha sido testada y evaluada en una placa AVR EVK1100, con un micro-controlador AVR32UC3A0. Se ha comprobado el comportamiento de los distintos modos para los distintos protocolos, definidos previamente. Como resultado se proporcionan las medidades de rendimiento de los distintos protocolos de cambio de modo.

Evaluación del dispositivo Raspberry Pi como elemento de despliegue de servicios en el marco de las Smart Grids

La tendencia actual de las redes de telecomunicaciones conduce a pensar en un futuro basado en el concepto emergente de las Smart Cities¸ que tienen como objetivo el desarrollo urbano basado en un modelo de sostenibilidad que responda a las necesidades crecientes de las ciudades. Dentro de las Smart Cities podemos incluir el concepto de Smart Grid, el cual está referido a sistemas de administración y producción de energía eficientes, que permitan un sistema energético sostenible, y que den cabida a las fuentes de energía renovables. Sistemas de este tipo se muestran a los usuarios como un conjunto de servicios con los que interactuar sin ser tan sólo un mero cliente, sino un agente más del entorno energético. Por otro lado, los sistemas de software distribuidos son cada vez más comunes en una infraestructura de telecomunicaciones cada vez más extensa y con más capacidades. Dentro de este ámbito tecnológico, las arquitecturas orientadas a servicios han crecido exponencialmente sobre todo en el sector empresarial. Con sistemas basados en estas arquitecturas, se pueden ofrecer a empresas y usuarios sistemas software basados en el concepto de servicio. Con la progresión del hardware actual, la miniaturización de los equipos es cada vez mayor, sin renunciar por ello a la potencia que podemos encontrar en sistemas de mayor tamaño. Un ejemplo es el dispositivo Raspberry Pi, que contiene un ordenador plenamente funcional contenido en el tamaño de una cajetilla de tabaco, y con un coste muy reducido. En este proyecto se pretenden aunar los tres conceptos expuestos. De esta forma, se busca utilizar el dispositivo Raspberry Pi como elemento de despliegue integrado en una arquitectura de Smart Grid orientada a servicios. En los trabajos realizados se ha utilizado la propuesta definida por el proyecto de I+D europeo e-GOTHAM, con cuya infraestructura se ha tenido ocasión de realizar diferentes pruebas de las descritas en esta memoria. Aunque esta arquitectura está orientada a la creación de una Smart Grid, lo experimentado en este PFG podría encajar en otro tipo de aplicaciones. Dentro del estudio sobre las soluciones software actuales, se ha trabajado en la evaluación de la posibilidad de instalar un Enterprise Service Bus en el Raspberry Pi y en la optimización de la citada instalación. Una vez conseguida una instalación operativa, se ha desarrollado un controlador de un dispositivo físico (sensor/actuador), denominado Dispositivo Lógico, a modo de prueba de la viabilidad del uso del Raspberry Pi para actuar como elemento en el que instalar aplicaciones en entornos de Smart Grid o Smart Home. El éxito logrado con esta experimentación refuerza la idea de considerar al Raspberry Pi, como un importante elemento a tener en cuenta para el despliegue de servicios de Smart Cities o incluso en otros ámbitos tecnológicos. ABSTRACT. The current trend of telecommunication networks lead to think in a future based on the emerging concept of Smart Cities, whose objective is to ensure the urban development based on a sustainable model to respond the new necessities of the cities. Within the Smart cites we can include the concept of Smart Grid, which is based on management systems and efficient energy production, allowing a sustainable energy producing system, and that includes renewable energy sources. Systems of this type are shown to users as a set of services that allow users to interact with the system not only as a single customer, but also as other energy environment agent. Furthermore, distributed software systems are increasingly common in a telecommunications infrastructure more extensive and with more capabilities. Within this area of technology, service-oriented architectures have grown exponentially especially in the business sector. With systems based on these architectures, can be offered to businesses and users software systems based on the concept of service. With the progression of the actual hardware, the miniaturization of computers is increasing, without sacrificing the power of larger systems. An example is the Raspberry Pi, which contains a fully functional computer contained in the size of a pack of cigarettes, and with a very low cost. This PFG (Proyecto Fin de Grado) tries to combine the three concepts presented. Thus, it is intended to use the Raspberry Pi device as a deployment element integrated into a service oriented Smart Grid architecture. In this PFG, the one proposed in the European R&D e-GOTHAM project has been observed. In addition several tests described herein have been carried out using the infrastructure of that project. Although this architecture is oriented to the creation of a Smart Grid, the experiences reported in this document could fit into other applications. Within the study on current software solutions, it have been working on assessing the possibility of installing an Enterprise Service Bus in the Raspberry Pi and optimizing that facility. Having achieved an operating installation, it has been developed a driver for a physical device (sensor / actuator), called logical device, for testing the feasibility of using the Raspberry Pi to act as an element in which to install applications in Smart Grid and Smart Home Environments. The success of this experiment reinforces the idea of considering the Raspberry Pi as an important element to take into account in the deployment of Smart Cities services or even in other technological fields.

Técnicas de diseño de pruebas en sistemas embebidos

El software es, cada vez más, una parte muy importante de cualquier circuito electrónico moderno, por ejemplo, un circuito realizado con algún tipo de microprocesador debe incorporar un programa de control por pequeño que sea. Al utilizarse programas informáticos en los circuitos electrónicos modernos, es muy aconsejable, por no decir imprescindible, realizar una serie de pruebas de calidad del diseño realizado. Estas pruebas son cada vez más complicadas de realizar debido al gran tamaño del software empleado en los sistemas actuales, por este motivo, es necesario estructurar una serie de pruebas con el fin de realizar un sistema de calidad, y en algunos casos, un sistema que no presente ningún peligro para el ser humano o el medio ambiente. Esta propuesta consta de la explicación de las técnicas de diseño de pruebas que existen actualmente (por lo menos las más básicas ya que es un tema muy extenso) para realizar el control de calidad del software que puede contener un sistema embebido. Además, muchos circuitos electrónicos, debido a su control o exigencia hardware, es imprescindible que sean manipulados por algún programa que requiera más que un simple microprocesador, me refiero a que se deban controlar por medio de un pequeño programa manipulado por un sistema operativo, ya sea Linux, AIX, Unix, Windows, etc., en este caso el control de calidad se debería llevar a cabo con otras técnicas de diseño. También se puede dar el caso que el circuito electrónico a controlar se deba hacer por medio de una página web. El objetivo es realizar un estudio de las actuales técnicas de diseño de pruebas que están orientadas al desarrollo de sistemas embebidos. ABSTRACT. Software is increasingly a very important part of any modern electronic circuit, for example, a circuit made with some type of microprocessor must incorporate a control program no matter the small it is. When computer programs are used in modern electronic circuits, it is quite advisable if not indispensable to perform a series of quality tests of the design. These tests are becoming more and more difficult to be performed due to the large size of the software used in current systems, which is why it is necessary to structure a series of tests in order to perform a quality system, and in some cases, a system with no danger to humans or to the environment. This proposal consists of an explanation of the techniques used in the tests (at least the most basic ones since it is a very large topic) for quality control of software which may contain an embedded system. In addition, a lot of electronic circuits, due to its control or required hardware, it is essential to be manipulated by a program that requires more than a simple microprocessor, I mean that they must be controlled by means of a small program handled by an operating system, being Linux, AIX, Unix, Windows, etc., in this case the quality control should be carried out with other design techniques. The objective is to study the current test design techniques that are geared to the development of embedded systems. It can also occur that the electronic circuit should be controlled by means of a web page.

Desarrollo de un sistema automático de medida para el control del consumo en sistemas empotrados

El Grupo de Diseño Electrónico y Microelectrónico de la Universidad Politécnica de Madrid -GDEM- se dedica, entre otras cosas, al estudio y mejora del consumo en sistemas empotrados. Es en este lugar y sobre este tema donde el proyecto a exponer ha tomado forma y desarrollo. Según un artículo de la revista online Revista de Electrónica Embebida, un sistema empotrado o embebido es aquel “sistema controlado por un microprocesador y que gracias a la programación que incorpora o que se le debe incorporar, realiza una función específica para la que ha sido diseñado, integrando en su interior la mayoría de los elementos necesarios para realizar dicho función”. El porqué de estudiar sobre este tema responde a que, cada vez, hay mayor presencia de sistemas empotrados en nuestra vida cotidiana. Esto es debido a que se está tendiendo a dotar de “inteligencia” a todo lo que puedan hacer nuestra vida un poco más fácil. Nos podemos encontrar dichos sistemas en fábricas, oficinas de atención a los ciudadanos, sistemas de seguridad de hogar, relojes, móviles, lavadoras, hornos, aspiradores y un largo etcétera en cualquier aparato que nos podamos imaginar. A pesar de sus grandes ventajas, aún hay grandes inconvenientes. El mayor problema que supone a día de hoy es la autonomía del mismo sistema, ya que hablamos de aparatos que muchas veces están alimentados por baterías -para ayudar a su portabilidad–. Por esto, se está intentando dotar a dichos sistemas de una capacidad de ahorro de energía y toma de decisiones que podrían ayudar a duplicar la autonomía de dicha batería. Un ejemplo claro son los Smartphones de hoy en día, unos aparatos casi indispensables que pueden tener una autonomía de un día. Esto es poco práctico para el usuario en caso de viajes, trabajo u otras situaciones en las que se le dé mucho uso y no pueda tener acceso a una red eléctrica. Es por esto que surge la necesidad de investigar, sin necesidad de mejorar el hardware del sistema, una manera de mejorar esta situación. Este proyecto trabajará en esa línea creando un sistema automático de medida el cual generará las corrientes que servirán como entrada para verificar el sistema de adquisición que junto con la tarjeta Beagle Board permitirá la toma de decisiones en relación con el consumo de energía. Para realizar este sistema, nos ayudaremos de diferentes herramientas que podremos encontrar en el laboratorio del GDEM, como la fuente de alimentación Agilent y la Beagle Board –como principales herramientas de trabajo- . El objetivo principal será la simulación de unas señales que, después de pasar un proceso de conversión y tratado, harán la función de representación del consumo de cada una de las partes que pueden formar un sistema empotrado genérico. Por lo tanto, podemos decir que el sistema hará la funcionalidad de un banco de pruebas que ayudará a simular dicho consumo para que el microprocesador del sistema pueda llegar a tomar alguna decisión. ABSTRACT. The Electronic and Microelectronic Design Group of Universidad Politécnica de Madrid -GDEM- is in charge, between other issues, of improving the embedded system’s consumption. It is in this place and about this subject where the exposed project has taken shape and development. According to an article from de online magazine Revista de Electronica Embebida, an embedded system is “the one controlled by a microprocessor and, thanks to the programing that it includes, it carries out a specific function what it has been designed for, being integrated in it the most necessary elements for realizing the already said function”. The because of studying this subject, answers that each time there is more presence of the embedded system in our daily life. This is due to the tendency of providing “intelligence” to all what can make our lives easier. We can find this kind of systems in factories, offices, security systems, watchers, mobile phones, washing machines, ovens, hoovers and, definitely, in all kind of machines what we can think of. Despite its large vantages, there are still some inconveniences. Nowadays, the most important problem is the autonomy of the system itself when machines that have to be supplied by batteries –making easier the portability-. Therefore, this project is going after a save capacity of energy for the system as well as being able to take decisions in order to duplicate batteries’ autonomy. Smartphones are a clear example. They are a very successful product but the autonomy is just one day. This is not practical for users, at all, if they have to travel, to work or to do any activity that involves a huge use of the phone without a socket nearby. That is why the need of investigating a way to improve this situation. This project is working on this line, creating an automatic system that will generate the currents for verifying the acquisition system that, with the beagle board, will help taking decisions regarding the energy’s consumption. To carry out this system, we need different tools that we can find in the laboratory of the group previously mentioned, like power supply Agilent and the Beagle Board – as main working tools –. The main goal is the simulation of some signals that, after a conversion process, will represent de consumption of each of the parts in the embedded generic system. Therefore, the system will be a testing ground that simulate the consumption, once sent to the processor, to be processed and so the microprocessor system might take some decision.

Hammer: an Android based application for end-user industrial robot programming

This paper presents a novel tablet based end-user interface for industrial robot programming (called Hammer). This application makes easier to program tasks for industrial robots like polishing, milling or grinding. It is based on the Scratch programming language, but specifically design and created for Android OS. It is a visual programming concept that allows non-skilled programmer operators to create programs. The application also allows to monitor the tasks while it is being executed by overlapping real time information through augmented reality. The application includes a teach pendant screen that can be customized according to the operator needs at every moment.

Mixed-criticality design of a satellite software system

The continuous increment of processors computational power and the requirements on additional functionality and services are motivating a change in the way embedded systems are built. Components with different criticality level are allocated in the same processor, which give rise to mixed-criticality systems. The use of partitioned systems is a way of preventing undesirable interferences between components with different criticality level. An hypervisor provides these partitions or virtual machines, ensuring spatial, temporal and fault isolation between them. The purpose of this paper is to illustrate the development of a mixed-critical system. The attitude control subsystem is used for showing the different steps, which are supported by a toolset developed in the context of the MultiPARTES research project.

A Dynamically Adaptable Image Processing Application Trading Off Between High Performance, Consumption and Dependability in Real Time

As embedded systems evolve, problems inherent to technology become important limitations. In less than ten years, chips will exceed the maximum allowed power consumption affecting performance, since, even though the resources available per chip are increasing, frequency of operation has stalled. Besides, as the level of integration is increased, it is difficult to keep defect density under control, so new fault tolerant techniques are required. In this demo work, a new dynamically adaptable virtual architecture (ARTICo3) to allow dynamic and context-aware use of resources is implemented in a high performance Wireless Sensor node (HiReCookie) to perform an image processing application.

Unificación de los protocolos de multipunto fiable optimizando la escalabilidad y el retardo

Las aplicaciones distribuidas que precisan de un servicio multipunto fiable son muy numerosas, y entre otras es posible citar las siguientes: bases de datos distribuidas, sistemas operativos distribuidos, sistemas de simulación interactiva distribuida y aplicaciones de distribución de software, publicaciones o noticias. Aunque en sus orígenes el dominio de aplicación de tales sistemas distribuidos estaba reducido a una única subred (por ejemplo una Red de Área Local) posteriormente ha surgido la necesidad de ampliar su aplicabilidad a interredes. La aproximación tradicional al problema del multipunto fiable en interredes se ha basado principalmente en los dos siguientes puntos: (1) proporcionar en un mismo protocolo muchas garantías de servicio (por ejemplo fiabilidad, atomicidad y ordenación) y a su vez algunas de éstas en distintos grados, sin tener en cuenta que muchas aplicaciones multipunto que precisan fiabilidad no necesitan otras garantías; y (2) extender al entorno multipunto las soluciones ya adoptadas en el entorno punto a punto sin considerar las características diferenciadoras; y de aquí, que se haya tratado de resolver el problema de la fiabilidad multipunto con protocolos extremo a extremo (protocolos de transporte) y utilizando esquemas de recuperación de errores, centralizados (las retransmisiones se hacen desde un único punto, normalmente la fuente) y globales (los paquetes solicitados se vuelven a enviar al grupo completo). En general, estos planteamientos han dado como resultado protocolos que son ineficientes en tiempo de ejecución, tienen problemas de escalabilidad, no hacen un uso óptimo de los recursos de red y no son adecuados para aplicaciones sensibles al retardo. En esta Tesis se investiga el problema de la fiabilidad multipunto en interredes operando en modo datagrama y se presenta una forma novedosa de enfocar el problema: es más óptimo resolver el problema de la fiabilidad multipunto a nivel de red y separar la fiabilidad de otras garantías de servicio, que pueden ser proporcionadas por un protocolo de nivel superior o por la propia aplicación. Siguiendo este nuevo enfoque se ha diseñado un protocolo multipunto fiable que opera a nivel de red (denominado RMNP). Las características más representativas del RMNP son las siguientes; (1) sigue una aproximación orientada al emisor, lo cual permite lograr un grado muy alto de fiabilidad; (2) plantea un esquema de recuperación de errores distribuido (las retransmisiones se hacen desde ciertos encaminadores intermedios que siempre estarán más cercanos a los miembros que la propia fuente) y de ámbito restringido (el alcance de las retransmisiones está restringido a un cierto número de miembros). Este esquema hace posible optimizar el retardo medio de distribución y disminuir la sobrecarga introducida por las retransmisiones; (3) incorpora en ciertos encaminadores funciones de agregación y filtrado de paquetes de control, que evitan problemas de implosión y reducen el tráfico que fluye hacia la fuente. Con el fin de evaluar el comportamiento del protocolo diseñado, se han realizado pruebas de simulación obteniéndose como principales conclusiones que, el RMNP escala correctamente con el tamaño del grupo, hace un uso óptimo de los recursos de red y es adecuado para aplicaciones sensibles al retardo.---ABSTRACT---There are many distributed applications that require a reliable multicast service, including: distributed databases, distributed operating systems, distributed interactive simulation systems and distribution applications of software, publications or news. Although the application domain of distributed systems of this type was originally confíned to a single subnetwork (for example, a Local Área Network), it later became necessary extend their applicability to internetworks. The traditional approach to the reliable multicast problem in internetworks is based mainly on the following two points: (1) provide a lot of service guarantees in one and the same protocol (for example, reliability, atomicity and ordering) and different levéis of guarantee in some cases, without taking into account that many multicast applications that require reliability do not need other guarantees, and (2) extend solutions adopted in the unicast environment to the multicast environment without taking into account their distinctive characteristics. So, the attempted solutions to the multicast reliability problem were end-to-end protocols (transport protocols) and centralized error recovery schemata (retransmissions made from a single point, normally the source) and global error retrieval schemata (the requested packets are retransmitted to the whole group). Generally, these approaches have resulted in protocols that are inefficient in execution time, have scaling problems, do not make optimum use of network resources and are not suitable for delay-sensitive applications. Here, the multicast reliability problem is investigated in internetworks operating in datagram mode and a new way of approaching the problem is presented: it is better to solve to the multicast reliability problem at network level and sepárate reliability from other service guarantees that can be supplied by a higher protocol or the application itself. A reliable multicast protocol that operates at network level (called RMNP) has been designed on the basis of this new approach. The most representative characteristics of the RMNP are as follows: (1) it takes a transmitter-oriented approach, which provides for a very high reliability level; (2) it provides for an error retrieval schema that is distributed (the retransmissions are made from given intermedíate routers that will always be closer to the members than the source itself) and of restricted scope (the scope of the retransmissions is confined to a given number of members), and this schema makes it possible to optimize the mean distribution delay and reduce the overload caused by retransmissions; (3) some routers include control packet aggregation and filtering functions that prevent implosión problems and reduce the traffic flowing towards the source. Simulation test have been performed in order to evalúate the behaviour of the protocol designed. The main conclusions are that the RMNP scales correctly with group size, makes optimum use of network resources and is suitable for delay-sensitive applications.

Integración de RVC-HEVC y OpenHEVC sobre la plataforma MultiDSP C6678

Este proyecto se basa en la integración de funciones optimizadas de OpenHEVC en el códec Reconfigurable Video Coding (RVC) - High Efficiency Video Coding (HEVC). RVC es un framework capaz de generar automáticamente el código que implementa cualquier estándar de video mediante el uso de librerías. Estas librerías contienen la definición de bloques funcionales de los que se componen los distintos estándares de video a implementar. Sin embargo, como desventaja a la facilidad de creación de estándares utilizando este framework, las librerías que utiliza no se encuentran optimizadas. Por ello se pretende que el códec RVC-HEVC sea capaz de realizar llamadas a funciones optimizadas, que para el estudio éstas se encontrarán en la librería OpenHEVC. Por otro lado, estos codificadores de video se pueden encontrar implementados tanto en PCs como en sistemas embebidos. Los Digital Signal Processors (DSPs) son unas plataformas especializadas en el procesamiento digital, teniendo una alta velocidad en el cómputo de operaciones matemáticas. Por ello, para este proyecto se integrará RVC-HEVC con las llamadas a OpenHEVC en una plataforma DSP como la TMS320C6678. Una vez completa la integración se efectuan medidas de eficiencia para ver cómo las llamadas a funciones optimizadas mejoran la velocidad en la decodificación de imágenes. ABSTRACT. This project is based in the integration of optimized functions from OpenHEVC in the RVC-HEVC (Reconfigurable Video Coding- High Efficiency Video Coding) codec. RVC is a framework capable of generating automatically any type of video standard with the use of libraries. Inside these libraries there are the definitions of the functional blocks which make up the different standards, in which for the case of study will be the HEVC standard. Nevertheless, as a downside for the simplicity in producing standards with the RVC tool, these libraries are not optimized. Thus, one of the goals for the project will be to make the RVC-HEVC call optimized functions, in which in this case they will be inside the OpenHEVC library. On the other hand, these video encoders can be implemented both in PCs and embedded systems. The DSPs (Digital Signal Processors) are platforms specialized in digital processing, being able to compute mathematical operations in a short period of time. Consequently, for this project the integration of the RVC-HEVC with calls to the OpenHEVC library will be done in a DSP platform such as a TMS320C6678. Once completed the integration, performance measures will be carried out to evaluate the improvement in the decoding speed obtained when optimized functions are used by the RVC-HEVC.

Estudo sobre a interação de métodos anti-ilhamento para sistemas fotovoltaicos conectados à rede de distribuição de baixa tensão com múltiplos inversores.

Este trabalho estuda a interação entre os métodos anti-ilhamento aplicados em sistemas fotovoltaicos residenciais, operando simultaneamente em uma rede de distribuição de baixa tensão. Os sistemas fotovoltaicos em geral interagem entre si, com a rede de distribuição da concessionária e com outras fontes de geração distribuída. Uma consequência importante dessa interação é a ocorrência do ilhamento, que acontece quando as fontes de geração distribuída fornecem energia ao sistema elétrico de potência mesmo quando esta se encontra eletricamente isolada do sistema elétrico principal. A função anti-ilhamento é uma proteção extremamente importante, devendo estar presente em todos os sistemas de geração distribuída. Atualmente, são encontradas diversas técnicas na literatura. Muitas delas oferecem proteção adequada quando um inversor está conectado à linha de distribuição, mas podem falhar quando dois ou mais funcionam simultaneamente, conectados juntos ou próximos entre si. Dois destes métodos são analisados detalhadamente nesse estudo, avaliados em uma rede de distribuição residencial de baixa tensão. Os resultados obtidos mostram que a influência de um método sobre o outro é dependente da predominância de cada um deles dentro do sistema elétrico. Contudo, nas condições analisadas o ilhamento foi detectado dentro do limite máximo estabelecido pelas normas pertinentes.

Um método de otimização da relação desempenho/consumo de energia para arquiteturas multi-cores heterogêneas em FPGA

Devido às tendências de crescimento da quantidade de dados processados e a crescente necessidade por computação de alto desempenho, mudanças significativas estão acontecendo no projeto de arquiteturas de computadores. Com isso, tem-se migrado do paradigma sequencial para o paralelo, com centenas ou milhares de núcleos de processamento em um mesmo chip. Dentro desse contexto, o gerenciamento de energia torna-se cada vez mais importante, principalmente em sistemas embarcados, que geralmente são alimentados por baterias. De acordo com a Lei de Moore, o desempenho de um processador dobra a cada 18 meses, porém a capacidade das baterias dobra somente a cada 10 anos. Esta situação provoca uma enorme lacuna, que pode ser amenizada com a utilização de arquiteturas multi-cores heterogêneas. Um desafio fundamental que permanece em aberto para estas arquiteturas é realizar a integração entre desenvolvimento de código embarcado, escalonamento e hardware para gerenciamento de energia. O objetivo geral deste trabalho de doutorado é investigar técnicas para otimização da relação desempenho/consumo de energia em arquiteturas multi-cores heterogêneas single-ISA implementadas em FPGA. Nesse sentido, buscou-se por soluções que obtivessem o melhor desempenho possível a um consumo de energia ótimo. Isto foi feito por meio da combinação de mineração de dados para a análise de softwares baseados em threads aliadas às técnicas tradicionais para gerenciamento de energia, como way-shutdown dinâmico, e uma nova política de escalonamento heterogeneity-aware. Como principais contribuições pode-se citar a combinação de técnicas de gerenciamento de energia em diversos níveis como o nível do hardware, do escalonamento e da compilação; e uma política de escalonamento integrada com uma arquitetura multi-core heterogênea em relação ao tamanho da memória cache L1.

Partial Product Reduction based on Look-Up Tables

In this paper a new technique for partial product reduction based on the use of look-up tables for efficient processing is presented. We describe how to construct counter devices with pre-calculated data and their subsequent integration into the whole operation. The development of reduction trees organizations for this kind of devices uses the inherent integration benefits of computer memories and offers an alternative implementation to classic operation methods. Therefore, in our experiments we compare our implementation model with CMOS technology model in homogeneous terms.

An Electronic Reconfigurable Neural Architecture for Intrusion Detection

The explosive growth of the traffic in computer systems has made it clear that traditional control techniques are not adequate to provide the system users fast access to network resources and prevent unfair uses. In this paper, we present a reconfigurable digital hardware implementation of a specific neural model for intrusion detection. It uses a specific vector of characterization of the network packages (intrusion vector) which is starting from information obtained during the access intent. This vector will be treated by the system. Our approach is adaptative and to detecting these intrusions by using a complex artificial intelligence method known as multilayer perceptron. The implementation have been developed and tested into a reconfigurable hardware (FPGA) for embedded systems. Finally, the Intrusion detection system was tested in a real-world simulation to gauge its effectiveness and real-time response.

Optimizing the data intensive mediator-based Web services composition

Effectively using heterogeneous, distributed information has attracted much research in recent years. Current web services technologies have been used successfully in some non data intensive distributed prototype systems. However, most of them can not work well in data intensive environment. This paper provides an infrastructure layer in data intensive environment for the effectively providing spatial information services by using the web services over the Internet. We extensively investigate and analyze the overhead of web services in data intensive environment, and propose some new optimization techniques which can greatly increase the system’s efficiency. Our experiments show that these techniques are suitable to data intensive environment. Finally, we present the requirement of these techniques for the information of web services over the Internet.

An Autonomic Framework for Mobile Cloud Computing

This thesis presents the formal definition of a novel Mobile Cloud Computing (MCC) extension of the Networked Autonomic Machine (NAM) framework, a general-purpose conceptual tool which describes large-scale distributed autonomic systems. The introduction of autonomic policies in the MCC paradigm has proved to be an effective technique to increase the robustness and flexibility of MCC systems. In particular, autonomic policies based on continuous resource and connectivity monitoring help automate context-aware decisions for computation offloading. We have also provided NAM with a formalization in terms of a transformational operational semantics in order to fill the gap between its existing Java implementation NAM4J and its conceptual definition. Moreover, we have extended NAM4J by adding several components with the purpose of managing large scale autonomic distributed environments. In particular, the middleware allows for the implementation of peer-to-peer (P2P) networks of NAM nodes. Moreover, NAM mobility actions have been implemented to enable the migration of code, execution state and data. Within NAM4J, we have designed and developed a component, denoted as context bus, which is particularly useful in collaborative applications in that, if replicated on each peer, it instantiates a virtual shared channel allowing nodes to notify and get notified about context events. Regarding the autonomic policies management, we have provided NAM4J with a rule engine, whose purpose is to allow a system to autonomously determine when offloading is convenient. We have also provided NAM4J with trust and reputation management mechanisms to make the middleware suitable for applications in which such aspects are of great interest. To this purpose, we have designed and implemented a distributed framework, denoted as DARTSense, where no central server is required, as reputation values are stored and updated by participants in a subjective fashion. We have also investigated the literature regarding MCC systems. The analysis pointed out that all MCC models focus on mobile devices, and consider the Cloud as a system with unlimited resources. To contribute in filling this gap, we defined a modeling and simulation framework for the design and analysis of MCC systems, encompassing both their sides. We have also implemented a modular and reusable simulator of the model. We have applied the NAM principles to two different application scenarios. First, we have defined a hybrid P2P/cloud approach where components and protocols are autonomically configured according to specific target goals, such as cost-effectiveness, reliability and availability. Merging P2P and cloud paradigms brings together the advantages of both: high availability, provided by the Cloud presence, and low cost, by exploiting inexpensive peers resources. As an example, we have shown how the proposed approach can be used to design NAM-based collaborative storage systems based on an autonomic policy to decide how to distribute data chunks among peers and Cloud, according to cost minimization and data availability goals. As a second application, we have defined an autonomic architecture for decentralized urban participatory sensing (UPS) which bridges sensor networks and mobile systems to improve effectiveness and efficiency. The developed application allows users to retrieve and publish different types of sensed information by using the features provided by NAM4J's context bus. Trust and reputation is managed through the application of DARTSense mechanisms. Also, the application includes an autonomic policy that detects areas characterized by few contributors, and tries to recruit new providers by migrating code necessary to sensing, through NAM mobility actions.