Using Distributed Temperature Sensing to monitor field scale dynamics of ground surface temperature and related substrate heat flux

We present one of the first studies of the use of Distributed Temperature Sensing (DTS) along fibre-optic cables to purposely monitor spatial and temporal variations in ground surface temperature (GST) and soil temperature, and provide an estimate of the heat flux at the base of the canopy layer and in the soil. Our field site was at a groundwater-fed wet meadow in the Netherlands covered by a canopy layer (between 0-0.5 m thickness) consisting of grass and sedges. At this site, we ran a single cable across the surface in parallel 40 m sections spaced by 2 m, to create a 40×40 m monitoring field for GST. We also buried a short length (≈10 m) of cable to depth of 0.1±0.02 m to measure soil temperature. We monitored the temperature along the entire cable continuously over a two-day period and captured the diurnal course of GST, and how it was affected by rainfall and canopy structure. The diurnal GST range, as observed by the DTS system, varied between 20.94 and 35.08◦C; precipitation events acted to suppress the range of GST. The spatial distribution of GST correlated with canopy vegetation height during both day and night. Using estimates of thermal inertia, combined with a harmonic analysis of GST and soil temperature, substrate and soil-heat fluxes were determined. Our observations demonstrate how the use of DTS shows great promise in better characterising area-average substrate/soil heat flux, their spatiotemporal variability, and how this variability is affected by canopy structure. The DTS system is able to provide a much richer data set than could be obtained from point temperature sensors. Furthermore, substrate heat fluxes derived from GST measurements may be able to provide improved closure of the land surface energy balance in micrometeorological field studies. This will enhance our understanding of how hydrometeorological processes interact with near-surface heat fluxes.

A case study of the Tatweer school system in Saudi Arabia: the perceptions of leaders and teachers

School reform is a major concern in many countries that seek to improve their educational systems and enhance their performances. In consequence, many global schemes, theories, studies, attempts, and programmes have been introduced to promote education in recent years. Saudi Arabia is one of these countries that implemented educational change by introducing many initiatives. The Tatweer Programme is one of these initiatives and is considered as a major recent reform. The main purpose of this study is to investigate this reform in depth by examining the perceptions and experiences of the Tatweer leaders and teachers to find out which extent they have been enabled to be innovative, and to examine the types of leadership and decision-making that have been undertaken by such schools. This study adopted a qualitative case study that employed interviews, focus groups and documentary analysis. The design of the study has been divided into two phases; the first phase was the feasibility study and the second phase was the main study. The research sample of the feasibility study was head teachers, educational experts and Tatweer Unit’s members. The sample of the main study was three Tatweer schools, Tatweer Unit members and one official of Tatweer Project in Riyadh. The findings of this study identified the level of autonomy in managing the school; the Tatweer schools’ system is semi-autonomous when it comes to the internal management, but it lacks autonomy when it comes to staff appointment, student assessment, and curriculum development. In addition, the managerial work has been distributed through teams and members; the Excellence Team plays a critical role in school effectiveness leading an efficient change. Moreover, Professional Learning Communities have been used to enhance the work within Tatweer schools. Finally the findings show that there have been major shifts in the Tatweer schools’ system; the shifting from centralisation to semi-decentralisation; from the culture of the individual to the culture of community; from the traditional school to one focused on self-evaluation and planning; from management to leadership; and from an isolated school being open to society. These shifts have impacted positively on the attitudes of students, parents and staff.

Distributed access control and privacy for the internet of me

This article presents an experimental scalable message driven IoT and its security architecture based on Decentralized Information Flow Control. The system uses a gateway that exports SoA (REST) interfaces to the internet simplifying external applications whereas uses DIFC and asynchronous messaging within the home environment.

Dynamics of Aeromonas species isolated from wastewater treatment system

Aeromonas are widely distributed in the aquatic environment, and are considered to be emerging organisms that can produce a series of virulence factors. The present study was carried out in a sanitary sewage stabilization pond treatment system, located in Lins, State of Sao Paulo, Brazil. Most probable number was applied for estimation of the genus Aeromonas. Colony isolation was carried out on blood agar ampicillin and confirmed by biochemical characterization. Aeromonas species were isolated in 72.4% of influent samples, and in 55.2 and 48.3% of effluent from anaerobic and facultative lagoons, respectively. Thirteen Aeromonas species were isolated, representing most of the recognized species of these organisms. Even though it was possible to observe a tendency of decrease, total elimination of these organisms from the studied system was not achieved. Understanding of the pathogenic organism`s dynamics in wastewater treatment systems with a reuse potential is especially important because of the risk it represents.

Measuring Application Availability,Usage and Performance : Implementation of EnView System

The main objective for this degree project is to implement an Application Availability Monitoring (AAM) system named Softek EnView for Fujitsu Services. The aim of implementing the AAM system is to proactively identify end user performance problems, such as application and site performance, before the actual end users experience them. No matter how well applications and sites are designed and nomatter how well they meet business requirements, they are useless to the end users if the performance is slow and/or unreliable. It is important for the customers to find out whether the end user problems are caused by the network or application malfunction. The Softek EnView was comprised of the following EnView components: Robot, Monitor, Reporter, Collector and Repository. The implemented system, however, is designed to use only some of these EnView elements: Robot, Reporter and depository. Robots can be placed at any key user location and are dedicated to customers, which means that when the number of customers increases, at the sametime the amount of Robots will increase. To make the AAM system ideal for the company to use, it was integrated with Fujitsu Services’ centralised monitoring system, BMC PATROL Enterprise Manager (PEM). That was actually the reason for deciding to drop the EnView Monitor element. After the system was fully implemented, the AAM system was ready for production. Transactions were (and are) written and deployed on Robots to simulate typical end user actions. These transactions are configured to run with certain intervals, which are defined collectively with customers. While they are driven against customers’ applicationsautomatically, transactions collect availability data and response time data all the time. In case of a failure in transactions, the robot immediately quits the transactionand writes detailed information to a log file about what went wrong and which element failed while going through an application. Then an alert is generated by a BMC PATROL Agent based on this data and is sent to the BMC PEM. Fujitsu Services’ monitoring room receives the alert, reacts to it according to the incident management process in ITIL and by alerting system specialists on critical incidents to resolve problems. As a result of the data gathered by the Robots, weekly reports, which contain detailed statistics and trend analyses of ongoing quality of IT services, is provided for the Customers.

A Unified Load Generator for Geographically Distributed Generation ofNetwork Traffic

During the last decade, the Internet usage has been growing at an enormous rate which has beenaccompanied by the developments of network applications (e.g., video conference, audio/videostreaming, E-learning, E-Commerce and real-time applications) and allows several types ofinformation including data, voice, picture and media streaming. While end-users are demandingvery high quality of service (QoS) from their service providers, network undergoes a complex trafficwhich leads the transmission bottlenecks. Considerable effort has been made to study thecharacteristics and the behavior of the Internet. Simulation modeling of computer networkcongestion is a profitable and effective technique which fulfills the requirements to evaluate theperformance and QoS of networks. To simulate a single congested link, simulation is run with asingle load generator while for a larger simulation with complex traffic, where the nodes are spreadacross different geographical locations generating distributed artificial loads is indispensable. Onesolution is to elaborate a load generation system based on master/slave architecture.

Combined solar and pellet heating systems for single-family houses : How to achieve decreased electricity usage, increased system efficiency and increased solar gains

In Sweden, there are about 0.5 million single-family houses that are heated by electricity alone, and rising electricity costs force the conversion to other heating sources such as heat pumps and wood pellet heating systems. Pellet heating systems for single-family houses are currently a strongly growing market. Future lack of wood fuels is possible even in Sweden, and combining wood pellet heating with solar heating will help to save the bio-fuel resources. The objectives of this thesis are to investigate how the electrically heated single-family houses can be converted to pellet and solar heating systems, and how the annual efficiency and solar gains can be increased in such systems. The possible reduction of CO-emissions by combining pellet heating with solar heating has also been investigated. Systems with pellet stoves (both with and without a water jacket), pellet boilers and solar heating have been simulated. Different system concepts have been compared in order to investigate the most promising solutions. Modifications in system design and control strategies have been carried out in order to increase the system efficiency and the solar gains. Possibilities for increasing the solar gains have been limited to investigation of DHW-units for hot water production and the use of hot water for heating of dishwashers and washing machines via a heat exchanger instead of electricity (heat-fed appliances). Computer models of pellet stoves, boilers, DHW-units and heat-fed appliances have been developed and the parameters for the models have been identified from measurements on real components. The conformity between the models and the measurements has been checked. The systems with wood pellet stoves have been simulated in three different multi-zone buildings, simulated in detail with heat distribution through door openings between the zones. For the other simulations, either a single-zone house model or a load file has been used. Simulations were carried out for Stockholm, Sweden, but for the simulations with heat-fed machines also for Miami, USA. The foremost result of this thesis is the increased understanding of the dynamic operation of combined pellet and solar heating systems for single-family houses. The results show that electricity savings and annual system efficiency is strongly affected by the system design and the control strategy. Large reductions in pellet consumption are possible by combining pellet boilers with solar heating (a reduction larger than the solar gains if the system is properly designed). In addition, large reductions in carbon monoxide emissions are possible. To achieve these reductions it is required that the hot water production and the connection of the radiator circuit is moved to a well insulated, solar heated buffer store so that the boiler can be turned off during the periods when the solar collectors cover the heating demand. The amount of electricity replaced using systems with pellet stoves is very dependant on the house plan, the system design, if internal doors are open or closed and the comfort requirements. Proper system design and control strategies are crucial to obtain high electricity savings and high comfort with pellet stove systems. The investigated technologies for increasing the solar gains (DHW-units and heat-fed appliances) significantly increase the solar gains, but for the heat-fed appliances the market introduction is difficult due to the limited financial savings and the need for a new heat distribution system. The applications closest to market introduction could be for communal laundries and for use in sunny climates where the dominating part of the heat can be covered by solar heating. The DHW-unit is economical but competes with the internal finned-tube heat exchanger which is the totally dominating technology for hot water preparation in solar combisystems for single-family houses.

Chained Negotiation for Distributed Notification Services

Distributed notification services allow consumers and publishers of notifications to interact with different notification services. However, such a distributed infrastructure makes it difficult to share notifications between consumers when consumers are allowed to specify Quality of Service levels. In this paper, we present a chained negotiation engine, enabling distributed notification services to support negotiation and to reuse existing subscriptions. We demonstrate the benefit to the system as a whole by reducing load on service providers and enabling content to be shared.

Analysis Of Semi-Distributed And Global Hydrological Models In The Central Tropical Basins Of The Gulf Of Mexico To The Effects Of Extreme Hydrometeorological Phenomena

In the last years extreme hydrometeorological phenomena have increased in number and intensity affecting the inhabitants of various regions, an example of these effects are the central basins of the Gulf of Mexico (CBGM) that they have been affected by 55.2% with floods and especially the state of Veracruz (1999-2013), leaving economic, social and environmental losses. Mexico currently lacks sufficient hydrological studies for the measurement of volumes in rivers, since is convenient to create a hydrological model (HM) suited to the quality and quantity of the geographic and climatic information that is reliable and affordable. Therefore this research compares the semi-distributed hydrological model (SHM) and the global hydrological model (GHM), with respect to the volumes of runoff and achieve to predict flood areas, furthermore, were analyzed extreme hydrometeorological phenomena in the CBGM, by modeling the Hydrologic Modeling System (HEC-HMS) which is a SHM and the Modèle Hydrologique Simplifié à I'Extrême (MOHYSE) which is a GHM, to evaluate the results and compare which model is suitable for tropical conditions to propose public policies for integrated basins management and flood prevention. Thus it was determined the temporal and spatial framework of the analyzed basins according to hurricanes and floods. It were developed the SHM and GHM models, which were calibrated, validated and compared the results to identify the sensitivity to the real model. It was concluded that both models conform to tropical conditions of the CBGM, having MOHYSE further approximation to the real model. Worth mentioning that in Mexico there is not enough information, besides there are no records of MOHYSE use in Mexico, so it can be a useful tool for determining runoff volumes. Finally, with the SHM and the GHM were generated climate change scenarios to develop risk studies creating a risk map for urban planning, agro-hydrological and territorial organization.

Implications of innovation for inclusive growth: a study of Medellín, Colombia's metro system and integral urban projects

Medellín, Colombia continues to attract global recognition for its evolution from a crimesaturated and desegregated city to an award-winning paragon of innovation. Two innovations in particular, the Metro System & the Integral Urban Projects, have fostered and contributed to Medellín’s inclusive growth, as indicated by a corresponding increase in both social and economic capital. Through a mixed methodology analysis of these two experiences, including participant observation, in-depth interviews with different industry leaders, and household surveys, this thesis explores the extent to which inclusive innovation has contributed to inclusive growth in Medellín. The surveys were distributed to three sensitive neighborhoods of Medellín and apply a Synthesized Framework for measuring inclusive growth, one that includes five indicators for social capital and five indicators for economic capital, emphasizing the importance of progression in both dimensions. By drawing on concepts of inclusivity surfacing more frequently in business lexicon and the emergence of a newly branded Medellín, the findings of this thesis indicates that the implementation of innovations in association with a unified city vision practiced by the local government, corporate and non-profit sector has contributed to achieving inclusive growth, and has left civilians hungry for more.

Transparent access to relational, autonomous and distributed databases using semantic web and service oriented technologies

With the constant grow of enterprises and the need to share information across departments and business areas becomes more critical, companies are turning to integration to provide a method for interconnecting heterogeneous, distributed and autonomous systems. Whether the sales application needs to interface with the inventory application, the procurement application connect to an auction site, it seems that any application can be made better by integrating it with other applications. Integration between applications can face several troublesome due the fact that applications may not have been designed and implemented having integration in mind. Regarding to integration issues, two tier software systems, composed by the database tier and by the “front-end” tier (interface), have shown some limitations. As a solution to overcome the two tier limitations, three tier systems were proposed in the literature. Thus, by adding a middle-tier (referred as middleware) between the database tier and the “front-end” tier (or simply referred application), three main benefits emerge. The first benefit is related with the fact that the division of software systems in three tiers enables increased integration capabilities with other systems. The second benefit is related with the fact that any modifications to the individual tiers may be carried out without necessarily affecting the other tiers and integrated systems and the third benefit, consequence of the others, is related with less maintenance tasks in software system and in all integrated systems. Concerning software development in three tiers, this dissertation focus on two emerging technologies, Semantic Web and Service Oriented Architecture, combined with middleware. These two technologies blended with middleware, which resulted in the development of Swoat framework (Service and Semantic Web Oriented ArchiTecture), lead to the following four synergic advantages: (1) allow the creation of loosely-coupled systems, decoupling the database from “front-end” tiers, therefore reducing maintenance; (2) the database schema is transparent to “front-end” tiers which are aware of the information model (or domain model) that describes what data is accessible; (3) integration with other heterogeneous systems is allowed by providing services provided by the middleware; (4) the service request by the “frontend” tier focus on ‘what’ data and not on ‘where’ and ‘how’ related issues, reducing this way the application development time by developers.

Histopathological analysis of the reproductive system of male dogs experimentally infected with Toxoplasma gondii

O presente trabalho teve como objetivo descrever eventuais alterações histopatológicas no sistema reprodutor (testículo e epidídimo) de cães machos experimentalmente infectados com Toxoplasma gondii. Para tal, 10 animais sorologicamente negativos para T. gondii foram selecionados e distribuídos em três grupos experimentais: GI - três cães inoculados com 2,0 x 10(5) oocistos da cepa P, GII - três cães infectados com 1,0 x 10(6) taquizoítos da cepa RH e GIII - quatro cães mantidos como controle. Pesquisa de anticorpos (IFI) contra T. gondii foi realizada. A infecção por T. gondii confirmou-se pela soroconversão de todos os machos infectados a partir do 7° e do 14° dia pós-inoculação (DPI) para cães que receberam taquizoítos e oocistos respectivamente. Decorridos 70DPI, realizou-se, em todos os cães, orquiectomia, e amostras (testículo e epidídimo) foram coletadas e processadas histologicamente para leitura em microscópio óptico. As seguintes alterações foram diagnosticadas: infiltrado inflamatório mononuclear leve e moderado em epidídimo, edema celular moderado, degeneração hidrópica e fibrose intersticial moderada em túbulos seminíferos. Os resultados histopatológicos do presente trabalho, aliados ao isolamento do T. gondii em fragmentos de testículo e epidídimo pela imunoistoquímica, juntamente com os resultados encontrados na literatura por outros autores em diferentes tecidos, permitem inferir que as alterações encontradas nos cães infectados com o respectivo protozoário são sugestivas de infecção toxoplásmica.

Digestible methionine plus cystine requirements of ISA Label broilers reared in free-range system

Three assays were carried out to determine the digestible methionine+cystine (Met+Cys) requirement for ISA Label broilers from both sexes. The birds were reared in free range system on starting phase (1 to 28 days), growing phase (28 to 56 days) and finishing phase (56 to 84 days). Four hundred and eighty birds were distributed into 24 pens, each one composed of shelter (3.13 m(2)) and pasture (72.87 m(2)). The experimental design was completely randomized with eight treatments as factorial arrangement (four Met+Cys levels and two sexes) with three replicates of 20 birds. The digestible Met+Cys levels were 0.532; 0.652; 0.772; 0.892% for starting phase; 0.515; 0.635; 0.755; 0.875% for growing phase and 0.469; 0.589; 0.709; 0.829% for finishing phase. The analyzed parameters were performance, carcass yield, body protein and fat deposition, weight and protein concentration in feathers. In the starting phase, the digestible Met+Cys level estimated for males was 0.765 and 0.803% for females, corresponding to 0.252 and 0.268% of Met+Cys/Mcal of ME, respectively. For the growing phase, the digestible Met+Cys level estimated was 0.716% for both sexes, corresponding to 0.235% of Met+Cys/Mcal of ME. For the finishing phase, the Met+Cys levels were 0.756 and 0.597% for males and females, corresponding to 0.244 and 0.193% of Met+Cys/Mcal of ME respectively.

Mecanismos de segurança para um sistema cooperativo de armazenamento de arquivos baseado em P2P

Previous works have studied the characteristics and peculiarities of P2P networks, especially security information aspects. Most works, in some way, deal with the sharing of resources and, in particular, the storage of files. This work complements previous studies and adds new definitions relating to this kind of systems. A system for safe storage of files (SAS-P2P) was specified and built, based on P2P technology, using the JXTA platform. This system uses standard X.509 and PKCS # 12 digital certificates, issued and managed by a public key infrastructure, which was also specified and developed based on P2P technology (PKIX-P2P). The information is stored in a special file with XML format which is especially prepared, facilitating handling and interoperability among applications. The intention of developing the SAS-P2P system was to offer a complementary service for Giga Natal network users, through which the participants in this network can collaboratively build a shared storage area, with important security features such as availability, confidentiality, authenticity and fault tolerance. Besides the specification, development of prototypes and testing of the SAS-P2P system, tests of the PKIX-P2P Manager module were also performed, in order to determine its fault tolerance and the effective calculation of the reputation of the certifying authorities participating in the system