843 resultados para Defect introduction and removal process
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
The potential of natural and heat-treated Macauba palm cake as adsorbent for the removal of Methylene Blue (MB) and Congo Red (CR) from solution has been investigated. Equilibrium adsorption was attained in <7 h and the process was favored at pH 5.0 for MB and pH 6.5 for CR with an adsorbent (g):adsorbate (mL) ratio of 1:200 and an initial concentration of adsorbate of 25 mg L−1. The maximum adsorption capacities of the natural and heat-treated materials were, respectively, 25.80 and 32.30 mg g−1 for MB, and 32.00 and 20.30 mg g−1 for CR. The isotherm model proposed by Sips represented most adequately the adsorption of MB and CR. The adsorptions of the dyes were best described in terms of a pseudo second-order reaction. Thermodynamic parameters such as ΔHo, ΔSo and ΔGo were calculated. The adsorption process was found to be endothermic and spontaneous. Macauba palm cake is adequate for the removal of waste dye from industrial effluents by virtue of its abundance, low cost and efficiency of adsorption.
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
Introduction: The oxidative process plays a fundamental role in the pathophysiology of sickle cell anemia (SCA), and population and environmental characteristics may influence redox balance. The aim of this study was to evaluate lipid peroxidation and antioxidant capacity in Brazilian Hb S carriers undergoing different therapies.MethodsBlood samples from 270 individuals were analyzed (Hb SS, n=68; Hb AS, n=53, and Hb AA, n=149). Hemoglobin genotypes were assessed through cytological, electrophoretic, chromatographic, and molecular methods. Plasma lipid peroxidation and antioxidant capacity were measured by spectrophotometric methods.ResultsPatients with SCA who used iron-chelating drugs combined with hydroxyurea, associated with regular transfusions, showed lower levels of TBARS (P <= 0.05), higher levels of TEAC (P <= 0.01), and lower TBARS/TEAC ratio (R=255.8). The redox profile of Hb AS subjects was not statistically different (P>0.05) from that of Hb AA subjects.ConclusionThe data suggest that oxidative stress is lower in the patients with SCA who received regular blood transfusions associated with the combined use of HU and iron chelators than the group received only HU. The redox system of the Hb AS carriers is compatible with the control group.
Resumo:
doi: 10.1111/j.1741-2358.2011.00526.x Biological evaluation of the bone healing process after application of two potentially osteogenic proteins: an animal experimental model Objective: The aim of this work was to analyse qualitatively and quantitatively the newly formed bone after insertion of rhBMP-2 and protein extracted from Hevea brasiliensis (P-1), associated or not with a carrier in critical bone defects created in Wistar rat calvarial bone, using histological and histomorphometrical analyses. Materials and methods: Eighty-four male Wistar rats were used, divided into two groups, according to the period of time until the sacrifice (2 and 6 weeks). Each one of these groups was subdivided into six groups with seven animals each, according to the treatments: (1) 5 mu g of pure rhBMP-2, (2) 5 mu g of rhBMP-2/monoolein gel, (3) pure monoolein gel, (4) 5 mu g of pure P-1, (5) 5 mu g of P-1/monoolein gel and (6) critical bone defect controls. The animals were euthanised and the calvarial bone tissue removed for histological and histomorphometrical analyses. Result and conclusion: The results showed an improvement in the bone healing process using the rhBMP-2 protein, associated or not with a material carrier in relation to the other groups, and this process demonstrated to be time dependent.
Resumo:
Autotrophic denitrification coupled with sulfide oxidation represents an interesting alternative for the simultaneous removal of nitrate/nitrite and sulfide from wastewaters. The applicability of such bioprocess is especially advantageous for the post treatment of effluents from anaerobic reactors, since they usually produce sulfides, which can be used as endogenous electron donor for autotrophic denitrification. This study evaluated the effect of sulfide concentration on this bioprocess using nitrate and nitrite as electron acceptors in vertical fixed-bed reactors. The results showed that intermediary sulfur compounds were mainly produced when excess of electron donor was applied, which was more evident when nitrate was used. Visual evidences suggested that elemental sulfur was the intermediary compound produced. There was also evidence that the elemental sulfur previously formed was being used when sulfide was applied in stoichiometric concentration relative to nitrate/nitrite. Nitrite was more readily consumed than nitrate. For both electron acceptors and sulfide concentrations tested, autotrophic denitrification was not affected by residual heterotrophic denitrification via endogenic activity, occurring as a minor additional nitrogen removal process. (C) 2012 Elsevier Ltd. All rights reserved.
Resumo:
Background: The aim of this work was to study the new bone tissue formation after bone morphogenetic protein type 2 (rhBMP-2) and P-1 application, using 5 and 10 mu g of each, combined to a material carrier, in critical bone defects. Methods: It was used 70 Wistar rats (male, similar to 250 g) that were divided in 10 groups with seven animals on each. Groups are the following: critical bone defect only, pure monoolein gel, 5 mu g of pure P-1, 5 mu g of pure rhBMP-2, 5 mu g of P-1/monoolein gel, 5 mu g of rhBMP-2/monoolein gel, 10 mu g of pure P-1, 10 mu g of pure rhBMP-2, 10 mu g of P-1/monoolein gel, 10 mu g of rhBMP-2/monoolein gel. Animals were sacrificed after 4 weeks of the surgical procedure and the bone samples were submitted to histological, histomorphometrical, and immunohistochemical evaluations. Results: Animals treated with pure P-1 protein, in both situations with 5 mu g and 10 mu g, had no significant difference (P > 0.05) for new bone formation; other groups treated with 10 mu g were statistically significant (P < 0.05) among themselves and when compared with groups in which it was inserted the monoolein gel or critical bone defect only (P < 0.05). In the group involving the 10 mu g rhBMP-2/monoolein gel association, it was observed an extensive bone formation, even when compared with the same treatment without the gel carrier. Conclusion: Using this experimental animal model, more new bone tissue was found when it was inserted the rhBMP-2, especially when this protein was combined to the vehicle, and this process seems to be dose dependent. Microsc. Res. Tech., 2011.(c) 2011 Wiley Periodicals, Inc.
Resumo:
Introduction: Wound healing process involves the activation of extracellular matrix components, remodeling enzymes, cellular adhesion molecules, growth factors, cytokines and chemokines genes. However, the molecular patterns underlying the healing process periapical environment remain unclear. Here we hypothesized that endodontic infection might result in an imbalance in the expression of wound healing genes involved in the pathogenesis of periapical lesions. Furthermore, we suggest that differential expression of wound healing markers in active and latent granulomas could account for different clinical outcomes for such lesions. Methods: Study samples consisted of 93 periapical granulomas collected after endodontic surgeries and 24 healthy periodontal ligament tissues collected from premolars extracted for orthodontic purposes as control samples. Of these, 10 periapical granulomas and 5 healthy periapical tissues were used for expression analysis of 84 wound healing genes by using a pathway-specific real-time polymerase chain reaction array. The remaining 83 granulomas and all 24 control specimens were used to validate the obtained array data by real-time polymerase chain reaction. Observed variations in expression of wound healing genes were analyzed according to the classification of periapical granulomas as active/progressive versus inactive/stable (as determined by receptor activator for nuclear factor kappa B ligand/osteoprotegerin expression ratio). Results: We observed a marked increase of 5-fold or greater in SERPINE1, TIMP1, COL1A1, COL5A1, VTN, CTGF, FGF7, TGFB1, TNF, CXCL11, ITGA4, and ITGA5 genes in the periapical granulomas when compared with control samples. SERPINE1, TIMP1, COL1A1, TGFB1, and ITGA4 mRNA expression was significantly higher in inactive compared with active periapical granulomas (P < .001), whereas TNF and CXCL11 mRNA expression was higher in active lesions (P < .001). Conclusions: The identification of novel gene targets that curb the progression status of periapical lesions might contribute to a more accurate diagnosis and lead to treatment modalities more conducive to endodontic success. (J Endod 2012;38:185-190)
Resumo:
The corpus luteum (CL) lifespan is characterized by a rapid growth, differentiation and controlled regression of the luteal tissue, accompanied by an intense angiogenesis and angioregression. Indeed, the CL is one of the most highly vascularised tissue in the body with a proliferation rate of the endothelial cells 4- to 20-fold more intense than in some of the most malignant human tumours. This angiogenic process should be rigorously controlled to allow the repeated opportunities of fertilization. After a first period of rapid growth, the tissue becomes stably organized and prepares itself to switch to the phenotype required for its next apoptotic regression. In pregnant swine, the lifespan of the CLs must be extended to support embryonic and foetal development and vascularisation is necessary for the maintenance of luteal function. Among the molecules involved in the angiogenesis, Vascular Endothelial Growth Factor (VEGF) is the main regulator, promoting endothelial cells proliferation, differentiation and survival as well as vascular permeability and vessel lumen formation. During vascular invasion and apoptosis process, the remodelling of the extracellular matrix is essential for the correct evolution of the CL, particularly by the action of specific class of proteolytic enzymes known as matrix metalloproteinases (MMPs). Another important factor that plays a role in the processes of angiogenesis and angioregression during the CL formation and luteolysis is the isopeptide Endothelin-1 (ET-1), which is well-known to be a potent vasoconstrictor and mitogen for endothelial cells. The goal of the present thesis was to study the role and regulation of vascularisation in an adult vascular bed. For this purpose, using a precisely controlled in vivo model of swine CL development and regression, we determined the levels of expression of the members of VEGF system (VEGF total and specific isoforms; VEGF receptor-1, VEGFR-1; VEGF receptor-2, VEGFR-2) and ET- 1 system (ET-1; endothelin converting enzyme-1, ECE-1; endothelin receptor type A, ET-A) as well as the activity of the Ca++/Mg++-dependent endonucleases and gelatinases (MMP-2 and MMP-9). Three experiments were conducted to reach such objectives in CLs isolated from ovaries of cyclic, pregnant or fasted gilts. In the Experiment I, we evaluated the influence of acute fasting on VEGF production and VEGF, VEGFR-2, ET-1, ECE-1 and ET-A mRNA expressions in CLs collected on day 6 after ovulation (midluteal phase). The results indicated a down-regulation of VEGF, VEGFR-2, ET-1 and ECE-1 mRNA expression, although no change was observed for VEGF protein. Furthermore, we observed that fasting stimulated steroidogenesis by luteal cells. On the basis of the main effects of VEGF (stimulation of vessel growth and endothelial permeability) and ET-1 (stimulation of endothelial cell proliferation and vasoconstriction, as well as VEGF stimulation), we concluded that feed restriction possibly inhibited luteal vessel development. This could be, at least in part, compensated by a decrease of vasal tone due to a diminution of ET-1, thus ensuring an adequate blood flow and the production of steroids by the luteal cells. In the Experiment II, we investigated the relationship between VEGF, gelatinases and Ca++/Mg++-dependent endonucleases activities with the functional CL stage throughout the oestrous cycle and at pregnancy. The results demonstrated differential patterns of expression of those molecules in correspondence to the different phases of the oestrous cycle. Immediately after ovulation, VEGF mRNA/protein levels and MMP-9 activity are maximal. On days 5–14 after ovulation, VEGF expression and MMP-2 and -9 activities are at basal levels, while Ca++/Mg++-dependent endonuclease levels increased significantly in relation to day 1. Only at luteolysis (day 17), Ca++/Mg++-dependent endonuclease and MMP-2 spontaneous activity increased significantly. At pregnancy, high levels of MMP-9 and VEGF were observed. These results suggested that during the very early luteal phase, high MMPs activities coupled with high VEGF levels drive the tissue to an angiogenic phenotype, allowing CL growth under LH (Luteinising Hormone) stimulus, while during the late luteal phase, low VEGF and elevate MMPs levels may play a role in the apoptotic tissue and extracellular matrix remodelling during structural luteolysis. In the Experiment III, we described the expression patterns of all distinct VEGF isoforms throughout the oestrous cycle. Furthermore, the mRNA expression and protein levels of both VEGF receptors were also evaluated. Four novel VEGF isoforms (VEGF144, VEGF147, VEGF182, and VEGF164b) were found for the first time in swine and the seven identified isoforms presented four different patterns of expression. All isoforms showed their highest mRNA levels in newly formed CLs (day 1), followed by a decrease during mid-late luteal phase (days 10–17), except for VEGF182, VEGF188 and VEGF144 that showed a differential regulation during late luteal phase (day 14) or at luteolysis (day 17). VEGF protein levels paralleled the most expressed and secreted VEGF120 and VEGF164 isoforms. The VEGF receptors mRNAs showed a different pattern of expression in relation to their ligands, increasing between day 1 and 3 and gradually decreasing during the mid-late luteal phase. The differential regulation of some VEGF isoforms principally during the late luteal phase and luteolysis suggested a specific role of VEGF during tissue remodelling process that occurs either for CL maintenance in case of pregnancy or for noncapillary vessel development essential for tissue removal during structural luteolysis. In summary, our findings allow us to determine relationships among factors involved in the angiogenesis and angioregression mechanisms that take place during the formation and regression of the CL. Thus, CL provides a very interesting model for studying such factors in different fields of the basic research.
Resumo:
It is not unknown that the evolution of firm theories has been developed along a path paved by an increasing awareness of the organizational structure importance. From the early “neoclassical” conceptualizations that intended the firm as a rational actor whose aim is to produce that amount of output, given the inputs at its disposal and in accordance to technological or environmental constraints, which maximizes the revenue (see Boulding, 1942 for a past mid century state of the art discussion) to the knowledge based theory of the firm (Nonaka & Takeuchi, 1995; Nonaka & Toyama, 2005), which recognizes in the firm a knnowledge creating entity, with specific organizational capabilities (Teece, 1996; Teece & Pisano, 1998) that allow to sustaine competitive advantages. Tracing back a map of the theory of the firm evolution, taking into account the several perspectives adopted in the history of thought, would take the length of many books. Because of that a more fruitful strategy is circumscribing the focus of the description of the literature evolution to one flow connected to a crucial question about the nature of firm’s behaviour and about the determinants of competitive advantages. In so doing I adopt a perspective that allows me to consider the organizational structure of the firm as an element according to which the different theories can be discriminated. The approach adopted starts by considering the drawbacks of the standard neoclassical theory of the firm. Discussing the most influential theoretical approaches I end up with a close examination of the knowledge based perspective of the firm. Within this perspective the firm is considered as a knowledge creating entity that produce and mange knowledge (Nonaka, Toyama, & Nagata, 2000; Nonaka & Toyama, 2005). In a knowledge intensive organization, knowledge is clearly embedded for the most part in the human capital of the individuals that compose such an organization. In a knowledge based organization, the management, in order to cope with knowledge intensive productions, ought to develop and accumulate capabilities that shape the organizational forms in a way that relies on “cross-functional processes, extensive delayering and empowerment” (Foss 2005, p.12). This mechanism contributes to determine the absorptive capacity of the firm towards specific technologies and, in so doing, it also shape the technological trajectories along which the firm moves. After having recognized the growing importance of the firm’s organizational structure in the theoretical literature concerning the firm theory, the subsequent point of the analysis is that of providing an overview of the changes that have been occurred at micro level to the firm’s organization of production. The economic actors have to deal with challenges posed by processes of internationalisation and globalization, increased and increasing competitive pressure of less developed countries on low value added production activities, changes in technologies and increased environmental turbulence and volatility. As a consequence, it has been widely recognized that the main organizational models of production that fitted well in the 20th century are now partially inadequate and processes aiming to reorganize production activities have been widespread across several economies in recent years. Recently, the emergence of a “new” form of production organization has been proposed both by scholars, practitioners and institutions: the most prominent characteristic of such a model is its recognition of the importance of employees commitment and involvement. As a consequence it is characterized by a strong accent on the human resource management and on those practices that aim to widen the autonomy and responsibility of the workers as well as increasing their commitment to the organization (Osterman, 1994; 2000; Lynch, 2007). This “model” of production organization is by many defined as High Performance Work System (HPWS). Despite the increasing diffusion of workplace practices that may be inscribed within the concept of HPWS in western countries’ companies, it is an hazard, to some extent, to speak about the emergence of a “new organizational paradigm”. The discussion about organizational changes and the diffusion of HPWP the focus cannot abstract from a discussion about the industrial relations systems, with a particular accent on the employment relationships, because of their relevance, in the same way as production organization, in determining two major outcomes of the firm: innovation and economic performances. The argument is treated starting from the issue of the Social Dialogue at macro level, both in an European perspective and Italian perspective. The model of interaction between the social parties has repercussions, at micro level, on the employment relationships, that is to say on the relations between union delegates and management or workers and management. Finding economic and social policies capable of sustaining growth and employment within a knowledge based scenario is likely to constitute the major challenge for the next generation of social pacts, which are the main social dialogue outcomes. As Acocella and Leoni (2007) put forward the social pacts may constitute an instrument to trade wage moderation for high intensity in ICT, organizational and human capital investments. Empirical evidence, especially focused on the micro level, about the positive relation between economic growth and new organizational designs coupled with ICT adoption and non adversarial industrial relations is growing. Partnership among social parties may become an instrument to enhance firm competitiveness. The outcome of the discussion is the integration of organizational changes and industrial relations elements within a unified framework: the HPWS. Such a choice may help in disentangling the potential existence of complementarities between these two aspects of the firm internal structure on economic and innovative performance. With the third chapter starts the more original part of the thesis. The data utilized in order to disentangle the relations between HPWS practices, innovation and economic performance refer to the manufacturing firms of the Reggio Emilia province with more than 50 employees. The data have been collected through face to face interviews both to management (199 respondents) and to union representatives (181 respondents). Coupled with the cross section datasets a further data source is constituted by longitudinal balance sheets (1994-2004). Collecting reliable data that in turn provide reliable results needs always a great effort to which are connected uncertain results. Data at micro level are often subjected to a trade off: the wider is the geographical context to which the population surveyed belong the lesser is the amount of information usually collected (low level of resolution); the narrower is the focus on specific geographical context, the higher is the amount of information usually collected (high level of resolution). For the Italian case the evidence about the diffusion of HPWP and their effects on firm performances is still scanty and usually limited to local level studies (Cristini, et al., 2003). The thesis is also devoted to the deepening of an argument of particular interest: the existence of complementarities between the HPWS practices. It has been widely shown by empirical evidence that when HPWP are adopted in bundles they are more likely to impact on firm’s performances than when adopted in isolation (Ichniowski, Prennushi, Shaw, 1997). Is it true also for the local production system of Reggio Emilia? The empirical analysis has the precise aim of providing evidence on the relations between the HPWS dimensions and the innovative and economic performances of the firm. As far as the first line of analysis is concerned it must to be stressed the fundamental role that innovation plays in the economy (Geroski & Machin, 1993; Stoneman & Kwoon 1994, 1996; OECD, 2005; EC, 2002). On this point the evidence goes from the traditional innovations, usually approximated by R&D investment expenditure or number of patents, to the introduction and adoption of ICT, in the recent years (Brynjolfsson & Hitt, 2000). If innovation is important then it is critical to analyse its determinants. In this work it is hypothesised that organizational changes and firm level industrial relations/employment relations aspects that can be put under the heading of HPWS, influence the propensity to innovate in product, process and quality of the firm. The general argument may goes as follow: changes in production management and work organization reconfigure the absorptive capacity of the firm towards specific technologies and, in so doing, they shape the technological trajectories along which the firm moves; cooperative industrial relations may lead to smother adoption of innovations, because not contrasted by unions. From the first empirical chapter emerges that the different types of innovations seem to respond in different ways to the HPWS variables. The underlying processes of product, process and quality innovations are likely to answer to different firm’s strategies and needs. Nevertheless, it is possible to extract some general results in terms of the most influencing HPWS factors on innovative performance. The main three aspects are training coverage, employees involvement and the diffusion of bonuses. These variables show persistent and significant relations with all the three innovation types. The same do the components having such variables at their inside. In sum the aspects of the HPWS influence the propensity to innovate of the firm. At the same time, emerges a quite neat (although not always strong) evidence of complementarities presence between HPWS practices. In terns of the complementarity issue it can be said that some specific complementarities exist. Training activities, when adopted and managed in bundles, are related to the propensity to innovate. Having a sound skill base may be an element that enhances the firm’s capacity to innovate. It may enhance both the capacity to absorbe exogenous innovation and the capacity to endogenously develop innovations. The presence and diffusion of bonuses and the employees involvement also spur innovative propensity. The former because of their incentive nature and the latter because direct workers participation may increase workers commitment to the organizationa and thus their willingness to support and suggest inovations. The other line of analysis provides results on the relation between HPWS and economic performances of the firm. There have been a bulk of international empirical studies on the relation between organizational changes and economic performance (Black & Lynch 2001; Zwick 2004; Janod & Saint-Martin 2004; Huselid 1995; Huselid & Becker 1996; Cappelli & Neumark 2001), while the works aiming to capture the relations between economic performance and unions or industrial relations aspects are quite scant (Addison & Belfield, 2001; Pencavel, 2003; Machin & Stewart, 1990; Addison, 2005). In the empirical analysis the integration of the two main areas of the HPWS represent a scarcely exploited approach in the panorama of both national and international empirical studies. As remarked by Addison “although most analysis of workers representation and employee involvement/high performance work practices have been conducted in isolation – while sometimes including the other as controls – research is beginning to consider their interactions” (Addison, 2005, p.407). The analysis conducted exploiting temporal lags between dependent and covariates, possibility given by the merger of cross section and panel data, provides evidence in favour of the existence of HPWS practices impact on firm’s economic performance, differently measured. Although it does not seem to emerge robust evidence on the existence of complementarities among HPWS aspects on performances there is evidence of a general positive influence of the single practices. The results are quite sensible to the time lags, inducing to hypothesize that time varying heterogeneity is an important factor in determining the impact of organizational changes on economic performance. The implications of the analysis can be of help both to management and local level policy makers. Although the results are not simply extendible to other local production systems it may be argued that for contexts similar to the Reggio Emilia province, characterized by the presence of small and medium enterprises organized in districts and by a deep rooted unionism, with strong supporting institutions, the results and the implications here obtained can also fit well. However, a hope for future researches on the subject treated in the present work is that of collecting good quality information over wider geographical areas, possibly at national level, and repeated in time. Only in this way it is possible to solve the Gordian knot about the linkages between innovation, performance, high performance work practices and industrial relations.
Resumo:
ZUSAMMENFASSUNG Die Tauglichkeit von Hybridmaterialien auf der Basis von Zinkphosphathydrat-Zementen zum Einsatz als korrosionshemmende anorganische Pigmente oder zur prothetischen und konservierenden Knochen- und Zahntherapie wird weltweit empirisch seit den neunziger Jahren intensiv erforscht. In der vorliegenden Arbeit wurden zuerst Referenzproben, d.h. alpha-und beta-Hopeite (Abk. a-,b-ZPT) dank eines hydrothermalen Kristallisationsverfahrens in wässerigem Milieu bei 20°C und 90°C hergestellt. Die Kristallstruktur beider Polymorphe des Zinkphosphattetrahydrats Zn3(PO4)2 4 H2O wurde komplett bestimmt. Einkristall-strukturanalyse zeigt, daß der Hauptunterschied zwischen der alpha-und beta-Form des Zinkphosphattetrahydrats in zwei verschiedenen Anordnungen der Wasserstoffbrücken liegt. Die entsprechenden drei- und zweidimensionalen Anordnungen der Wasserstoffbrücken der a-und b-ZPT induzieren jeweils unterschiedliches thermisches Verhalten beim Aufwärmen. Während die alpha-Form ihr Kristallwasser in zwei definierten Stufen verliert, erzeugt die beta-Form instabile Dehydratationsprodukt. Dieses entspricht zwei unabhängigen, aber nebeneinander ablaufenden Dehydratationsmechanismen: (i) bei niedrigen Heizraten einen zweidimensionalen Johnson-Mehl-Avrami (JMA) Mechanismus auf der (011) Ebene, der einerseits bevorzugt an Kristallkanten stattfindet und anderseits von existierenden Kristalldefekten auf Oberflächen gesteuert wird; (ii) bei hohen Heizraten einem zweidimensionalen Diffusionsmechanismus (D2), der zuerst auf der (101) Ebene und dann auf der (110) Ebene erfolgt. Durch die Betrachtung der ZPT Dehydratation als irreversibele heterogene Festkörperstufenreaktion wurde dank eines „ähnlichen Endprodukt“-Protokolls das Dehydratationsphasendiagramm aufgestellt. Es beschreibt die möglichen Zusammenhänge zwischen den verschiedenen Hydratationszuständen und weist auf die Existenz eines Übergangszustandes um 170°C (d.h. Reaktion b-ZPT a-ZPT) hin. Daneben wurde auch ein gezieltes chemisches Ätzverfahren mit verdünnten H3PO4- und NH3 Lösungen angewendet, um die ersten Stufe des Herauslösens von Zinkphosphat genau zu untersuchen. Allerdings zeigen alpha- und beta-Hopeite charakteristische hexagonale und kubische Ätzgruben, die sich unter kristallographischer Kontrolle verbreitern. Eine zuverlässige Beschreibung der Oberfächenchemie und Topologie konnte nur durch AFM und FFM Experimente erfolgen. Gleichzeitig konnte in dieser Weise die Oberflächendefektdichte und-verteilung und die Volumenauflösungsrate von a-ZPT und b-ZPT bestimmt werden. Auf einem zweiten Weg wurde eine innovative Strategie zur Herstellung von basischen Zinkphosphatpigmenten erster und zweiter Generation (d.h. NaZnPO4 1H2O und Na2ZnPO4(OH) 2H2O) mit dem Einsatz von einerseits oberflächenmodifizierten Polystyrolatices (z.B. produziert durch ein Miniemulsionspolymerisationsverfahren) und anderseits von Dendrimeren auf der Basis von Polyamidoamid (PAMAM) beschritten. Die erhaltene Zeolithstruktur (ZPO) hat in Abhängigkeit von steigendem Natrium und Wassergehalt unterschiedliche kontrollierte Morphologie: hexagonal, würfelförmig, herzförmig, sechsarmige Sterne, lanzettenförmige Dendrite, usw. Zur quantitativen Evaluierung des Polymereinbaus in der Kristallstruktur wurden carboxylierte fluoreszenzmarkierte Latices eingesetzt. Es zeigt sich, daß Polymeradditive nicht nur das Wachstum bis zu 8 µm.min-1 reduzierten. Trotzdem scheint es auch als starker Nukleationsbeschleuniger zu wirken. Dank der Koordinationschemie (d.h. Bildung eines sechszentrigen Komplexes L-COO-Zn-PO4*H2O mit Ligandenaustausch) konnten zwei einfache Mechanismen zur Wirkung von Latexpartikeln bei der ZPO Kristallisation aufgezeigt werden: (i) ein Intrakorona- und (ii) ein Extrakorona-Keimbildungsmechanismus. Weiterhin wurde die Effizienz eines Kurzzeit- und Langzeitkorrosionschutzes durch maßgeschneiderte ZPO/ZPT Pigmente und kontrollierte Freisetzung von Phosphationen in zwei Näherungen des Auslösungsgleichgewichts abgeschätzt: (i) durch eine Auswaschungs-methode (thermodynamischer Prozess) und (ii) durch eine pH-Impulsmethode (kinetischer Prozess. Besonders deutlich wird der Ausflösungs-Fällungsmechanismus (d.h. der Metamorphismus). Die wesentliche Rolle den Natriumionen bei der Korrosionshemmung wird durch ein passendes zusammensetzungsabhängiges Auflösungsmodell (ZAAM) beschrieben, das mit dem Befund des Salzsprühteste und der Feuchtigkeitskammertests konsistent ist. Schließlich zeigt diese Arbeit das herausragende Potential funktionalisierter Latices (Polymer) bei der kontrollierten Mineralisation zur Herstellung maßgeschneiderter Zinkphosphat Materialien. Solche Hybridmaterialien werden dringend in der Entwicklung umweltfreundlicher Korrosionsschutzpigmente sowie in der Dentalmedizin benötigt.
Resumo:
Synthetic biology has recently had a great development, many papers have been published and many applications have been presented, spanning from the production of biopharmacheuticals to the synthesis of bioenergetic substrates or industrial catalysts. But, despite these advances, most of the applications are quite simple and don’t fully exploit the potential of this discipline. This limitation in complexity has many causes, like the incomplete characterization of some components, or the intrinsic variability of the biological systems, but one of the most important reasons is the incapability of the cell to sustain the additional metabolic burden introduced by a complex circuit. The objective of the project, of which this work is part, is trying to solve this problem through the engineering of a multicellular behaviour in prokaryotic cells. This system will introduce a cooperative behaviour that will allow to implement complex functionalities, that can’t be obtained with a single cell. In particular the goal is to implement the Leader Election, this procedure has been firstly devised in the field of distributed computing, to identify the process that allow to identify a single process as organizer and coordinator of a series of tasks assigned to the whole population. The election of the Leader greatly simplifies the computation providing a centralized control. Further- more this system may even be useful to evolutionary studies that aims to explain how complex organisms evolved from unicellular systems. The work presented here describes, in particular, the design and the experimental characterization of a component of the circuit that solves the Leader Election problem. This module, composed of an hybrid promoter and a gene, is activated in the non-leader cells after receiving the signal that a leader is present in the colony. The most important element, in this case, is the hybrid promoter, it has been realized in different versions, applying the heuristic rules stated in [22], and their activity has been experimentally tested. The objective of the experimental characterization was to test the response of the genetic circuit to the introduction, in the cellular environment, of particular molecules, inducers, that can be considered inputs of the system. The desired behaviour is similar to the one of a logic AND gate in which the exit, represented by the luminous signal produced by a fluorescent protein, is one only in presence of both inducers. The robustness and the stability of this behaviour have been tested by changing the concentration of the input signals and building dose response curves. From these data it is possible to conclude that the analysed constructs have an AND-like behaviour over a wide range of inducers’ concentrations, even if it is possible to identify many differences in the expression profiles of the different constructs. This variability accounts for the fact that the input and the output signals are continuous, and so their binary representation isn’t able to capture the complexity of the behaviour. The module of the circuit that has been considered in this analysis has a fundamental role in the realization of the intercellular communication system that is necessary for the cooperative behaviour to take place. For this reason, the second phase of the characterization has been focused on the analysis of the signal transmission. In particular, the interaction between this element and the one that is responsible for emitting the chemical signal has been tested. The desired behaviour is still similar to a logic AND, since, even in this case, the exit signal is determined by the hybrid promoter activity. The experimental results have demonstrated that the systems behave correctly, even if there is still a substantial variability between them. The dose response curves highlighted that stricter constrains on the inducers concentrations need to be imposed in order to obtain a clear separation between the two levels of expression. In the conclusive chapter the DNA sequences of the hybrid promoters are analysed, trying to identify the regulatory elements that are most important for the determination of the gene expression. Given the available data it wasn’t possible to draw definitive conclusions. In the end, few considerations on promoter engineering and complex circuits realization are presented. This section aims to briefly recall some of the problems outlined in the introduction and provide a few possible solutions.
Resumo:
The fall of the Berlin Wall opened the way for a reform path – the transition process – which accompanied ten former Socialist countries in Central and South Eastern Europe to knock at the EU doors. By the way, at the time of the EU membership several economic and structural weaknesses remained. A tendency towards convergence between the new Member States (NMS) and the EU average income level emerged, together with a spread of inequality at the sub-regional level, mainly driven by the backwardness of the agricultural and rural areas. Several progresses were made in evaluating the policies for rural areas, but a shared definition of rurality is still missing. Numerous indicators were calculated for assessing the effectiveness of the Common Agricultural Policy and Rural Development Policy. Previous analysis on the Central and Eastern European countries found that the characteristics of the most backward areas were insufficiently addressed by the policies enacted; the low data availability and accountability at a sub-regional level, and the deficiencies in institutional planning and implementation represented an obstacle for targeting policies and payments. The next pages aim at providing a basis for understanding the connections between the peculiarities of the transition process, the current development performance of NMS and the EU role, with particular attention to the agricultural and rural areas. Applying a mixed methodological approach (multivariate statistics, non-parametric methods, spatial econometrics), this study contributes to the identification of rural areas and to the analysis of the changes occurred during the EU membership in Hungary, assessing the effect of CAP introduction and its contribution to the convergence of the Hungarian agricultural and rural. The author believes that more targeted – and therefore efficient – policies for agricultural and rural areas require a deeper knowledge of their structural and dynamic characteristics.
Resumo:
One of the current trends in governance and legal development in Russia is aimed at establishing a modern, efficient and internationally harmonised system of safeguards of human rights and civil liberties. A fairly recent addition to this system has been the institution of ombudsman as a public authority specialised in promoting and protecting human rights and civil liberties. The introduction of this institution as well as its formalisation at the constitutional and legislative levels has been increasingly relevant and important, as it raises the dealings between the state and the individual to a new level. As an independent public institution resolving conflicts between citizens and government authorities, the ombudsman makes steps, within the scope of his jurisdiction, to restitute individual rights, and helps to enhance the reputation of government. The present work describes and assesses the birth, development and institutionalization process of the Ombudsman Office in the Russian Federation, at federal and regional levels, with a particular emphasis on the role of international references and cooperation for institution building. Ombudsmen have done a magnificent job in demonstrating value with the resolution of individual and systemic complaints; subsequent improvements to government; and economic savings by mitigating litigation costs.
Resumo:
Abstract (US) Composite material components design and production techniques are discussed in the present graduation paper. In particular, this paper covers the design process and the production process of a carbon-fiber composite material component for a high performance car, more specifically, the Dallara T12 race car. This graduation paper is split in two. After a brief introduction on existing composite materials (their origins and applications), the first part of the present paper covers the main theoretical concepts behind the design of composite material components: particular focus will be given to carbon-fiber composites. The second part of the present paper covers the whole design and production process that the candidate carried out to create the new front mainplane of the Dallara T12 race car. This graduation paper is the result of a six-months-long internship that the candidate conducted as Design Office Trainee inside Dallara Automobili S.p.A. Abstract (ITA) La presente tesi di laurea discute le metodologie progettuali e produttive legate alla realizzazione di un componente in materiale composito. Nello specifico, viene discussa la progettazione e la produzione di un componente in fibra di carbonio destinato ad una vettura da competizione. La vettura in esame è la Dallara T12. Il lavoro è diviso in due parti. Nella prima parte, dopo una breve introduzione sull’origine e le tipologie di materiali compositi esistenti, vengono trattati i concetti teorici fondamentali su cui si basa la progettazione di generici componenti in materiale composito, con particolare riguardo ai materiali in fibra di carbonio. Nella seconda parte viene discusso tutto il processo produttivo che il candidato ha portato a termine per realizzare il nuovo alettone anteriore della Dallara T12. La presente tesi di laurea è il risultato del lavoro di progettazione che il candidato ha svolto presso l’Ufficio Tecnico di Dallara Automobili S.p.A. nel corso di un tirocinio formativo di sei mesi.