Limestone Reactions in a Fluidized Bed Heat Exchanger of an Oxy-fuel Circulating Fluidized Bed Boiler

Oxy-fuel combustion in a circulating fluidized bed (CFB) boiler appears to be a promising option for capturing CO2 in power plants. Oxy-fuel combustion is based on burning of fuel in the mixture of oxygen and re-circulated flue gas instead of air. Limestone (CaCO3) is typically used for capturing of SO2 in CFB boilers where limestone calcines to calcium oxide (CaO). Because of high CO2 concentration in oxy-fuel combustion, calcination reaction may be hindered or carbonation, the reverse reaction of calcination, may occur. Carbonation of CaO particles can cause problems especially in the circulation loop of a CFB boiler where temperature level is lower than in the furnace. The aim of the thesis was to examine carbonation of CaO in a fluidized bed heat exchanger of a CFB boiler featuring oxy-fuel combustion. The calculations and analyzing were based on measurement data from an oxy-fuel pilot plant and on 0-dimensional (0D) gas balance of a fluidized bed heat exchanger. Additionally, the objective was to develop a 1-dimensional (1D) model of a fluidized bed heat exchanger by searching a suitable pre-exponential factor for a carbonation rate constant. On the basis of gas measurement data and the 0D gas balance, it was found that the amount of fluidization gas decreased as it flew through the fluidized bed heat exchanger. Most likely the reason for this was carbonation of CaO. It was discovered that temperature has a promoting effect on the reaction rate of carbonation. With the 1D model, a suitable pre-exponential factor for the equation of carbonation rate constant was found. However, during measurements there were several uncertainties, and in the calculations plenty of assumptions were made. Besides, the temperature level in the fluidized bed heat exchanger was relatively low during the measurements. Carbonation should be considered when fluidized bed heat exchangers and the capacity of related fans are designed for a CFB boiler with oxy-fuel combustion.

Feasibility of ASH DEC‐ process in treating sewage sludge and manure ash in Finland

In Finland the thermal treatment of sewage sludge has been moderate in 21th century. The reason has been the high moisture content of sludge. During 2005-2008, 97-99% of sewage sludge was utilized in landscaping and agriculture. However agricultural use has been during 2005-2007 less than 3 %. The aim of national waste management plan is that by 2016 100% of sludge is used either as soil amendment or energy. The most popular utilization method for manure is spreading it on arable land. The dry manures such as poultry manure and horse manure could also be used in incineration. The ashes could be used as fertilizers and while it is not suitable as a starter fertilizer, it is suitable in maintaining P levels in the soil. One of the main drivers for more efficient nutrient management is the eutrophication in lakes and the Baltic See. ASH DEC process can be used in concentrating phosphorus rich ashes while separating the heavy metals that could be included. ASH DEC process uses thermochemical treatment to produce renewable phosphate for fertilizer production. The process includes mixing of ashes and chlorine donors and subsequent treatment in rotary kiln for 20 min in temperature of 900 – 1 050 oC. The heavy metals evaporate and P-rich product is obtained. The toxic substances are retained in air pollution control system in form of mixed metal hydroxides. The aim of conducting this study is to estimate the potential of ASH DEC process in treating phosphorus rich ashes in Finland. The masses considered in are sewage sludge, dry manure from horses, and poultry and liquid pig manure. To date the usual treatment method for sewage sludge in Finland is composting or anaerobic digestion. Part of the amount of produced sewage sludge (800 kt/a fresh mass and 160 kt/a TS) could also be incinerated and the residual ashes used in ASH DEC process. Incinerating only manure can be economically difficult to manage because the incineration of manure is in Finland considered as waste incineration. Getting a permit for waste incineration is difficult and also small scale waste incineration is too expensive. The manure could act as an additional feedstock in counties with high density of animal husbandry where the land area might not be enough for spreading of manure. Now when the manure acts as a supplementary feedstock beside sludge, the ash can’t be used directly as fertilizer. Then it could be used in ASH DEC process. The perquisite is that the manure producers could pay for the incineration, which might prove problematic.

Sugarcane stems as larval habitat for the stable fly (Stomoxys calcitrans) in sugarcane plantations

Outbreaks of stable fly, Stomoxys calcitrans, cause losses for livestock producers located near sugarcane mills in Brazil, especially in southern Mato Grosso do Sul. The sugarcane mills are often pointed by local farmers as the primary source of these outbreaks; some mills also joined the farmers in combating the flies. Brazilian beef cattle production has great economic importance in similar level to bio-fuel production as ethanol. In this context, the wide-ranging knowledge on the biology and ecology of the stable fly, including larval habitats and their reproduction sites is extremely important for further development of control programs. This paper aims to report the occurrence and development of S. calcitrans larvae inside sugarcane stems in three municipalities of Mato Grosso do Sul. The sugarcane stems give protection against bad weather conditions and insecticide application. In this way, for sustainable sugarcane growth specific research concerning this situation should be conducted.

Characterisation of waste for combustion : with special reference to the role of zinc

Waste combustion has gone from being a volume reducing discarding-method to an energy recovery process for unwanted material that cannot be reused or recycled. Different fractions of waste are used as fuel today, such as; municipal solid waste, refuse derived fuel, and solid recovered fuel. Furthermore, industrial waste, normally a mixture between commercial waste and building and demolition waste, is common, either as separate fuels or mixed with, for example, municipal solid waste. Compared to fossil or biomass fuels, waste mixtures are extremely heterogeneous, making it a complicated fuel. Differences in calorific values, ash content, moisture content, and changing levels of elements, such as Cl and alkali metals, are common in waste fuel. Moreover, waste contains much higher levels of troublesome trace elements, such as Zn, which is thought to accelerate a corrosion process. Varying fuel quality can be strenuous on the boiler system and may cause fouling and corrosion of heat exchanger surfaces. This thesis examines waste fuels and waste combustion from different angles, with the objective of giving a better understanding of waste as an important fuel in today’s fuel economy. Several chemical characterisation campaigns of waste fuels over longer time periods (10-12 months) was used to determine the fossil content of Swedish waste fuels, to investigate possible seasonal variations, and to study the presence of Zn in waste. Data from the characterisation campaigns were used for thermodynamic equilibrium calculations to follow trends and determine the effect of changing concentrations of various elements. The thesis also includes a study of the thermal behaviour of Zn and a full—scale study of how the bed temperature affects the volatilisation of alkali metals and Zn from the fuel. As mixed waste fuel contains considerable amounts of fresh biomass, such as wood, food waste, paper etc. it would be wrong to classify it as a fossil fuel. When Sweden introduced waste combustion as a part of the European Union emission trading system in the beginning of 2013 there was a need for combustion plants to find a usable and reliable method to determine the fossil content. Four different methods were studied in full-scale of seven combustion plants; 14Canalysis of solid waste, 14C-analysis of flue gas, sorting analysis followed by calculations, and a patented balance method that is using a software program to calculate the fossil content based on parameters from the plant. The study showed that approximately one third of the coal in Swedish waste mixtures has fossil origins and presented the plants with information about the four different methods and their advantages and disadvantages. Characterisation campaigns also showed that industrial waste contain higher levels of trace elements, such as Zn. The content of Zn in Swedish waste fuels was determined to be approximately 800 mg kg-1 on average, based on 42 samples of solid waste from seven different plants with varying mixtures between municipal solid waste and industrial waste. A review study of the occurrence of Zn in fuels confirmed that the highest amounts of Zn are present in waste fuels rather than in fossil or biomass fuels. In tires, Zn is used as a vulcanizing agent and can reach concentration values of 9600-16800 mg kg-1. Waste Electrical and Electronic Equipment is the second Zn-richest fuel and even though on average Zn content is around 4000 mg kg-1, the values of over 19000 mg kg-1 were also reported. The increased amounts of Zn, 3000-4000 mg kg-1, are also found in municipal solid waste, sludge with over 2000 mg kg-1 on average (some exceptions up to 49000 mg kg-1), and other waste derived fuels (over 1000 mg kg-1). Zn is also found in fossil fuels. In coal, the average level of Zn is 100 mg kg-1, the higher amount of Zn was only reported for oil shale with values between 20-2680 mg kg-1. The content of Zn in biomass is basically determined by its natural occurrence and it is typically 10-100 mg kg-1. The thermal behaviour of Zn is of importance to understand the possible reactions taking place in the boiler. By using thermal analysis three common Zn-compounds were studied (ZnCl2, ZnSO4, and ZnO) and compared to phase diagrams produced with thermodynamic equilibrium calculations. The results of the study suggest that ZnCl2(s/l) cannot exist readily in the boiler due to its volatility at high temperatures and its conversion to ZnO in oxidising conditions. Also, ZnSO4 decomposes around 680°C, while ZnO is relatively stable in the temperature range prevailing in the boiler. Furthermore, by exposing ZnO to HCl in a hot environment (240-330°C) it was shown that chlorination of ZnO with HCl gas is possible. Waste fuel containing high levels of elements known to be corrosive, for example, Na and K in combination with Cl, and also significant amounts of trace elements, such as Zn, are demanding on the whole boiler system. A full-scale study of how the volatilisation of Na, K, and Zn is affected by the bed temperature in a fluidised bed boiler was performed parallel with a lab-scale study with the same conditions. The study showed that the fouling rate on deposit probes were decreased by 20 % when the bed temperature was decreased from 870°C to below 720°C. In addition, the lab-scale experiments clearly indicated that the amount of alkali metals and Zn volatilised depends on the reactor temperature.

Modeling of temperature regimes in a furnace of bubbling fluidized bed boiler

The work is mainly focused on the technology of bubbling fluidized bed combustion. Heat transfer and hydrodynamics of the process were examined in the work in detail. Special emphasis was placed on the process of heat exchange in a freeboard zone of bubbling fluidized bed boiler. Operating mode of bubbling fluidized bed boiler depends on many parameters. To assess the influence of some parameters on a temperature regime inside the furnace a simplified method of zonal modeling was used in the work. Thus, effects of bed material fineness, excess air ratio and changes in boiler load were studied. Besides the technology of combustion in bubbling fluidized bed, other common technologies of solid fuels combustion were reviewed. In addition, brief survey of most widely used types of solid fuel was performed in the work.

Fly pollination and pollinator sharing in two synchronopatric species: Cordia multispicata (Boraginaceae) and Borreria alata (Rubiaceae)

The floral biology of Cordia multispicata (Boraginaceae) and Borreria alata (Rubiaceae) was studied in natural populations in a fragment of the Atlantic forest in Pernambuco, northeastern Brazil. Both species flower during almost the whole year. Cordia multispicata is a shrubby species with white, distylous and tubular flowers. Borreria alata is a herbaceous species. Its flowers are whitish, tubular and have a polymorphism in relation to the size of their style. Floral anthesis in both species begins at 6:00 a.m. Sugar concentration in the nectar was about 16% in C. multispicata and 30% in B. alata. Nine species of flies, mainly of the genus Palpada (Syrphidae), were observed visiting flowers of the two species. Seven of them were observed visiting and pollinating flowers of both C. multispicata and B. alata. Two species visited only flowers of C. multispicata, whereas no fly was exclusive to B. alata flowers. Both species have similar flower morphology, flowering time, habitats in the forest and establish populations very close to each other. These facts can favour the pollinators’ sharing and increase pollinator attraction.

Effects of Fin Parameters on Gas-Side Heat Transfer Performance of H-Type Finned Tube Bundle in a Waste Heat Recovery Boiler

Alfa Laval Aalborg Oy designs and manufactures waste heat recovery systems utilizing extended surfaces. The waste heat recovery boiler considered in this thesis is a water-tube boiler where exhaust gas is used as the convective heat transfer medium and water or steam flowing inside the tubes is subject to cross-flow. This thesis aims to contribute to the design of waste heat recovery boiler unit by developing a numerical model of the H-type finned tube bundle currently used by Alfa Laval Aalborg Oy to evaluate the gas-side heat transfer performance. The main objective is to identify weaknesses and potential areas of development in the current H-type finned tube design. In addition, numerical simulations for a total of 15 cases with varying geometric parameters are conducted to investigate the heat transfer and pressure drop performance dependent on H-type fin geometry. The investigated geometric parameters include fin width and height, fin spacing, and fin thickness. Comparison between single and double tube type configuration is also conducted. Based on the simulation results, the local heat transfer and flow behaviour of the H-type finned tube is presented including boundary layer development between the fins, the formation of recirculation zone behind the tubes, and the local variations of flow velocity and temperature within the tube bundle and on the fin surface. Moreover, an evaluation of the effects of various fin parameters on heat transfer and pressure drop performance of H-type finned tube bundle has been provided. It was concluded that from the studied parameters fin spacing and fin width had the most significant effect on tube bundle performance and the effect of fin thickness was the least important. Furthermore, the results suggested that the heat transfer performance would increase due to enhanced turbulence if the current double tube configuration is replaced with single tube configuration, but further investigation and experimental measurements are required in order to validate the results.

Reducing auxiliary power of a fluid bed boiler island

The aim of this thesis is to find and analyze different methods which reduce fluid bed boilers’ auxiliary power consumption. The objective is to examine the effects and feasibility of these methods. The literature part explains how fluid bed boilers work and what are the main sources of auxiliary power consumption. Designs and operation of these equipment are presented. The literature part also discusses the basics of auxiliary power consumption reduction and introduces four low pressure drop constructions. The experimental part inspects six different methods. Effects of these methods on the auxiliary power consumption are calculated and their impacts on the operation of the boiler are modeled. Calculations show that reasonable changes can reduce fluid bed boiler’s auxiliary power consumption by 2,1-10,2 %. Biggest reductions come from lower air coefficients, smaller bed a-level pressures and lower primary/secondary air –ratios. Models showed no problems with the smaller bed a-level pressures. With the lower air coefficients and smaller primary/secondary air –ratios the models showed a significant increase in the carbon monoxide levels.

Spirit that wants to fly: Adorno under a spell

The starting point of Demirovic's text is Adorno’s idea that concepts as forms of thinking are constellations of power. Differently from many interpretations of Adorno as resigned, Demirovic shows that this assumption enables Adorno to give his own theory the character of interventions in the ideological consensus of everyday life with regard to emancipation.

Control of Bubbling Fluidized Bed Conditions

The objectives of this master’s thesis were to understand the importance of bubbling fluidized bed (BFB) conditions and to find out how digital image processing and acoustic emission technology can help in monitoring the bed quality. An acoustic emission (AE) measurement system and a bottom ash camera system were evaluated in acquiring information about the bed conditions. The theory part of the study describes the fundamentals of BFB boiler and evaluates the characteristics of bubbling bed. Causes and effects of bed material coarsening are explained. The ways and methods to monitor the behaviour of BFB are determined. The study introduces the operating principles of AE technology and digital image processing. The empirical part of the study describes an experimental arrangement and results of a case study at an industrial BFB boiler. Sand consumption of the boiler was reduced by optimization of bottom ash handling and sand feeding. Furthermore, data from the AE measurement system and the bottom ash camera system was collected. The feasibility of these two systems was evaluated. The particle size of bottom ash and the changes in particle size distribution were monitored during the test period. Neither of the systems evaluated was ready to serve in bed quality control accurately or fast enough. Particle size distributions according to the bottom ash camera did not correspond to the results of manual sieving. Comprehensive interpretation of the collected AE data requires much experience. Both technologies do have potential and with more research and development they may enable acquiring reliable and real-time information about the bed conditions. This information could help to maintain disturbance-free combustion process and to optimize bottom ash handling system.

Spare Part Management of Bubbling Fluidized Bed Boiler

Energy generation industry is very capital-intensive industry. Productivity and availability requirements have increased while competition and quality requirement have increased. Maintenance has a significant role that these requirements can be reached. Even maintenance is much more than repairing faults nowadays, spare parts are important part of maintenance. Large power boilers are user-specific therefore features of boilers vary from project to project. Equipment have been designed to follow the customer’s requirements therefore spare parts are mainly user-specific also. The study starts with literature review introducing maintenance, failure mechanisms, and systems and equipment of bubbling fluidized bed boiler. At the final part spare part management is discussed from boiler technology point of view. For this part of the study science publications about spare part management are utilized also some specialist from a boiler technology company and other original equipment manufacturers were interviewed. Spare part management is challenging from the boiler supplier point of view and the end user of spare parts has a responsibility of stocking items. Criticality analysis can be used for finding most critical devices of the process and spare part management shall focus to those items. Spare parts are part of risk management. Stocking spare parts is increasing costs but then high spare part availability is decreasing delay time caused by fault of item.

An investigative study on the effects of black fly (diptera: simuliidae) sugar meals on reproductive success and parasite transmission /

Black flies are opportunistic sugar-feeders. They take sugar meals from Homopteran honeydew secretions or plant nectars, depending on availability. Homopteran honeydew secretions contain both simple and complex carbohydrates while plant nectars contain primarily simple carbohydrates. In order to determine whether honeydew secretions offer more energy than plant nectars to their insect visitors a study of wild-caught black flies was undertaken in Algonquin Provincial Park, Canada during the spring of 1 998 and 1 999. It was hypothesized that female black flies maintained on honeydew sugars will survive longer, produce more eggs and have a greater parasite vectoring potential than those maintained on artificial nectar or distilled water. Results demonstrated that: (1) host-seeking female Prosimulimfuscum/mixtum and Simulium venustum maintained on artificial honeydew did not survive longer than those maintained on artificial nectar when fed ad libitum; (2) fiiUy engorged S. venustum and Simulium rugglesi maintained on artificial honeydew did not produce more eggs than those maintained on artificial nectar when fed ad libitum; and (3) S. rugglesi did not have a greater vectoring potential of Leucocytozoon simondi when maintained on artificial honeydew as opposed to artificial nectar when fed ad libitum. However, all flies maintained on the two sugars (artificial honeydew and artificial nectar) survived longer, produce more eggs and had greater vectoring potential than those maintained on distilled water alone.

Behavioural characteristics in phylogenetics : a case study using black fly (Diptera: Simuliidae) cocoon spinning behaviour

1-1 is torically, the predominan t method of reconstructing phylogenies has been through the use of morphological characters. There are new techniques now gaining acceptance, including molecular techniques al1d chromosomal information. Altl10ugh the study of behaviour has been used in a comparative framework, these analyses have, historically, been based on intuition. Hennig (1966) devised a neV\' method of reconstructing phylogenies which provided a 110ncircular method for formulating, testing and refining phylogenies. Subsequent s)Tstematists had virtually abandoned ecological and beha\lioural data as primary indicators of phylogenetic relationships (Brooks and McLennan 1991). Therefore, in a modern cladistic framework (sensu Hennig) the analysis of behavioural traits remains underrepresented as a method of reconstructing phylogenies. This thesis will reconstruct the phylogeny for species of black flies (Diptera: Simuliidae), using two steps. The first step is to thoroughl)' understand and explain the cocoon spinning in black fly larvae. There have bee115 previous descriptions of cocoon spinning, but all were incomplete or erroneous. The advances in technology, including video recorders and VCRs, have allowed this behaviour to be analyzed in great detail in 20 different species. A complete description of the cocoon spinning of Simulium \littatum is given. This description will be used as a template for the other species observed. The description and understanding of cococ)n spinning was the first step in undertaking a phylogenetic analysis using this behaviour. The behaviour was then broken down and analyzed, revealing 23 characters, 3 either qualitative and quantitative in nature. These characters were assessed in a cladistic framework (sensu Hennig) and a phylogenetic tree was reconstructed with a e.I of 0.91 and an R.I. of 0.96. This phylogenetic tree closely resembles a previously established pllylogenetic tree produced from morphological and cytological information. The importance of this result is the indication that, contrary to some authors, behavioural characters, if used properly, can add very informative characters to a data set.

The effect of feeding regime on larval black fly (Diptera: simuliidae) primary head fan ray number

Identification of larval simuliids has always been difficult due to the morphological similarity many species bear to one another. For this reason all characters available have been drawn upon to aid in species identification, including head fan ray number. Even in light of an increasing body of anecdotal reports that head fan ray number is not fixed, it has continued to be used to aid species identification. In the current experiment simuliid larvae were reared under controlled laboratory conditions to last instar in one of three feeding regimes. Out of nine trials, the results of six showed a significant inverse relationship between feeding regime and head fan ray number. In addition to the laboratory experiments, larvae were also collected from the field over the course of the spring and summer, 1994. From these samples significant interspecific and intraspecific variations in head fan ray number were found both spatially and temporally within Algonquin Park. From these data it is concluded that head fan ray number for the species analysed is a developmentally plastic character, which varies in response to food availability. Furthermore, given the extreme variations in head fan ray number found in some species, I recommend that head fan ray number not be used as an aid to identification unless it can be shown to be a fixed character for the species in question.