Inhalable particulate matter characterization in a medium-sized urban region in Brazil (São José dos Campos Town) - Part I: Morphology

In this study, the concentration and morphological characteristics of inhalable particulate material (PM10) were evaluated and associated with climatic conditions. The mean annual concentration was 11.0 µg m−3, varying between 0,647 µg m−3 and 36.8 µg m−3. Wind speed has a higher influence on PM10 dispersion, but direction was associated with particle source. During the wet period, wind speed is the main dispersion factor, while speed and direction both are important during the dry period. Based on the morphological characteristics, it is concluded that biogenic particles prevail during the rainy season and terrigenous particles during the dry period, depending on the wind direction and intensity.

FAST GC-FID METHOD FOR MONITORING ACIDIC AND BASIC CATALYTIC TRANSESTERIFICATION REACTIONS IN VEGETABLE OILS TO METHYL ESTER BIODIESEL PREPARATION

A fast gas chromatography with a flame ionisation detector (GC-FID) method for the simultaneous analysis of methyl palmitate (C16:0), stearate (C18:0), oleate (C18:1), linoleate (C18:2) and linolenate (C18:3) in biodiesel samples was proposed. The analysis was conducted in a customised ionic-liquid stationary-phase capillary, SLB-IL 111, with a length of 14 m, an internal diameter of 0.10 mm, a film thickness of 0.08 µm and operated isothermally at 160 °C using hydrogen as the carrier gas at a rate of 50 cm s-1 in run time about 3 min. Once methyl myristate (C14:0) is present lower than 0.5% m/m in real samples it was used as an internal standard. The method was successful applied to monitoring basic and acidic catalysis transesterification reactions of vegetable oils such as soybean, canola, corn, sunflower and those used in frying process.

Thermal modelling of semiconductor switches in three-level Neutral Point Clamped Medium Voltage DTC-inverter

The aim of this thesis is to investigate the thermal loading of medium voltage three-level NPC inverter’s semiconductor IGCT switches in different operation points. The objective is to reach both a fairly accurate off-line simulation program and also so simple a simulation model that its implementation into an embedded system could be reasonable in practice and a real time use should become feasible. Active loading limitation of the inverter can be realized with a thermal model which is practical in a real time use. Determining of the component heating has been divided into two parts; defining of component losses and establishing the structure of a thermal network. Basics of both parts are clarified. The simulation environment is Matlab-Simulink. Two different models are constructed – a more accurate one and a simplified one. Potential simplifications are clarified with the help of the first one. Simplifications are included in the latter model and the functionalities of both models are compared. When increasing the calculation time step a decreased number of considered components and time constants of the thermal network can be used in the simplified model. Heating of a switching component is dependent on its topological position and inverter’s operation point. The output frequency of the converter defines mainly which one of the switching components is – because of its losses and heating – the performance limiting component of the converter. Comparison of results given by different thermal models demonstrates that with larger time steps, describing of fast occurring switching losses becomes difficult. Generally articles and papers dealing with this subject are written for two-level inverters. Also inverters which apply direct torque control (DTC) are investigated rarely from the heating point of view. Hence, this thesis completes the former material.

A Semi-Selective agar medium to detect the presence of Xanthomonas axonopodis pv. malvacearum in naturally infected cotton seed

A semi-selective agar medium was developed for detection of Xanthomonas axonopodis pv. malvacearum (Xam) in cotton (Gossypium hirsutum) seed. The basic medium was peptone-sucrose-agar (PSA). Criteria for the semi-selective medium were the typical colony characters of Xam and its pathogenicity on cotton. Several systemic fungicides and antibiotics in different concentrations were tested alone or in combination with others. The final composition of the semi-selective agar medium was established after several attempts in order to inhibit most of the fungal and bacterial saprophytes and favour the development of Xam. It contained PSA + cyclohexamide, cephalexin, pencycuron, triadimenol and tolylfluanid. The bacteria were recovered from naturally infected seeds by the direct plating of 2,000 surface disinfected seeds on the semi-selective medium. The recovery of the pathogen from naturally infected leaf tissues and in dilution plating, on semi-selective medium and on nutrient agar, were comparable. Among the three detection methods tested, the semi-selective medium was found to be the most reliable and quantifiable. Degree of severity of angular leaf spot in the field was not always correlated with the level of infection in the seed. This is the first report of a semi-selective agar medium to detect the presence of Xam in naturally infected cotton seed.

Electron transfer by singlet excited state of porphyn and electron acceptor affinity in rigid medium: photoacoustic phase angle analysis

Photoacoustic spectroscopy provides information about both amplitude and phase of the response of a system to an optical excitation process. This paper presents the studies of the phase in the electron transfer process between octaethylporphyn (OEP) and quinone molecules dispersed in a polymeric matrix. It was observed a tendency in the phase behavior to small values only in the spectral region near to 620 nm, while for shorter wavelength did not show any tendency. These measurements suggested that the electron transfer to acceptor occurred with the participation of octaethylporphyn singlet excited state.

Sustaining competitive advantage in changing environment: Case small and medium sized sawmills

The aim of this study is to examine how small and medium sized (SME) sawmills sustain their competitive advantage in the changing environment. Firstly, this study researches what changes affect SME sawmills’ competitiveness and what factors construct their competitive advantage. Secondly, this study examines how SME sawmills sustain their competitive advantage in the future and how agile and flexible they are. The theoretical part of this study represents the existing literature related to changes and competitive advantage in changing situations. The empirical part was executed as a qualitative research and it consists of thematic interviews with two SME sawmills. The results of the study indicate that several change factors affect the competitiveness of SME sawmills and therefore it is crucial to be alert on them. SME sawmills sustain their competitive advantage in the future by specialization and by being agile.

Electrochemical evidence of sulfinic acid derivative as an intermediate in the reduction of aromatic sulfonyl chloride in an aprotic medium

The electrochemical reduction of p-nitrobenzenesulfonyl chloride (NBSCl) in dimethylsulfoxide (DMSO) solution is used here as a model to investigate the role of sulfinic acid derivative in this compound's global reduction process. Cyclic voltammetric experiments reveal the production of sulfinic acid derivative, which is important in chemical reactions involving the original compound and other intermediates. This paper also discusses the probable mechanisms of the reduction.

Sensitive spectrophotometric determination of lansoprazole in pharmaceuticals using ceric ammonium sulphate based on redox and complex formation reactions

Two simple sensitive and cost-effective spectrophotometric methods are described for the determination of lansoprazole (LPZ) in bulk drug and in capsules using ceric ammonium sulphate (CAS), iron (II), orthophenanthroline and thiocyanate as reagents. In both methods, an acidic solution of lansoprazole is treated with a measured excess of CAS followed by the determination of unreacted oxidant by two procedures involving different reaction schemes. The first method involves the reduction of residual oxidant by a known amount of iron(II), and the unreacted iron(II) is complexed with orthophenanthroline at a raised pH, and the absorbance of the resulting complex measured at 510 nm (method A). In the second method, the unreacted CAS is reduced by excess of iron (II), and the resulting iron (III) is complexed with thiocyanate in the acid medium and the absorbance of the complex measured at 470 nm (method B). In both methods, the amount CAS reacted corresponds to the amount of LPZ. In method A, the absorbance is found to increase linearly with the concentration of LPZ where as in method B a linear decrease in absorbance occurs. The systems obey Beer's law for 2.5-30 and 2.5-25 µg mL-1 for method A and method B, respectively, and the corresponding molar absorptivity values are 8.1×10³ and 1.5×10(4) L mol-1cm-1 . The methods were successfully applied to the determination of LPZ in capsules and the results tallied well with the label claim. No interference was observed from the concomitant substances normally added to capsules.

Feasibility study for acidic biorefinery concept

The integration a recovery process for spent sulfite liquor from a sulfite cooking process with a kraft pulp mill was studied in this thesis work. The process includes a fermentation process for the production of biofuel. The calculation for three cases was done. The three cases considered were with a spruce sulfite pulp production of 100, 250 and 1000 Adt/day corresponding to 10, 25 and 100% of the total pulp production. A kraft cooking process with prehydrolysis was taken in consideration as reference. Compared to kraft cooking with prehydrolysis a bigger amount of ethanol can be produced by sulfite cooking. In the kraft prehydrolysis case 40 t/day of ethanol and 1000 Adt/day pine pulp is produced and in the sulfite case the production is 113 t/day of ethanol and 1000 Adt/day of spruce pulp. The energy consumption in the sulfite process is assumed to be slightly higher than in the kraft prehydrolysis process. The recovery system for spent liquor mix was studied. The evaporation of the spent cooking liquors should be done separately. The approximately composition of melt was calculated. A comparison of all four cases was done and profitability was estimated.

Titrimetric assay of lisinopril in aqueous and non-aqueous media

Four simple titrimetric procedures are described for the determination of lisinopril (LNP) in bulk and in pharmaceuticals based on the neutralization of basic-amino and acidic carboxylic acid groups present in LNP. Method A is based on the neutralization of basic amino groups using perchloric acid as titrant in anhydrous acetic acid medium. Method B, method C and method D are based on neutralization of carboxylic acid group using NaOH, sodium methoxide and methanolic KOH, as titrants, respectively. Method A is applicable over 2.0-20.0 mg range and the calculations are based in the molar ratio of 1:2 (LNP:HClO4). Method B, method C and method D are applicable over 2.0-20.0 mg, 1.0-10.0 mg and 5.0-15.0 mg range, respectively, and their respective molar ratios are 1:1 (LNP:NaOH), 1:2 (LNP:CH3ONa) and 1:1 (LNP:KOH). Intraday and inter day accuracy and precision of the methods were evaluated and the results showed intra- and inter-day precision less than 2.7% (RSD), and accuracy of < 2.5 % (RE). The developed methods were applied to determine LNP in tablets and the results were validated statistically by comparing the results with those of the reference method by applying the Student's t-test and F-test. The accuracy was further ascertained by recovery studies via standard addition technique. No interferences from common tablet exipients was observed.

Primeiro relato do Tomato spotted wilt virus (TSWV) em Campanula medium L. no Brasil

Plantas de campânula (Campanula medium) exibindo mosaico e necrose foliar e anéis em flores foram coletadas em uma estufa comercial de flores na região de Atibaia, SP. Suspeitando de possível etiologia viral, amostras de tecido lesionado foram analisadas por ensaios de transmissão mecânica, microscopia eletrônica e sorologia. Todos os resultados apontaram para a presença do Tomato spotted wilt virus (TSWV) como o responsável pelos sintomas. Esse é o primeiro relato deste patógeno em campânula no Brasil.

Semi-selective medium for Fusarium graminearum detection in seed samples

Fungi of the genus Fusarium cause a variety of difficult to control diseases in different crops, including winter cereals and maize. Among the species of this genus Fusarium graminearum deserves attention. The aim of this work was to develop a semi-selective medium to study this fungus. In several experiments, substrates for fungal growth were tested, including fungicides and antibiotics such as iprodiona, nystatin and triadimenol, and the antibacterial agents streptomycin and neomycin sulfate. Five seed samples of wheat, barley, oat, black beans and soybeans for F. graminearum detection by using the media Nash and Snyder agar (NSA), Segalin & Reis agar (SRA) and one-quarter dextrose agar (1/4PDA; potato 50g; dextrose 5g and agar 20g), either unsupplemented or supplemented with various concentrations of the antimicrobial agents cited above. The selected components and concentrations (g.L-1) of the proposed medium, Segalin & Reis agar (SRA-FG), were: iprodiona 0.05; nystatin 0,025; triadimenol 0.015; neomycin sulfate 0.05; and streptomycin sulfate, 0.3 added of ¼ potato sucrose agar. In the isolation from seeds of cited plant species, the sensitivity of this medium was similar to that of NSA but with de advantage of maintaining the colony morphological aspects similar to those observed in potato-dextrose-agar medium.

Semi-selective culture medium for Exserohilum turcicum isolation from corn seeds

Northern corn leaf blight, caused by Exserohilum turcicum (Et), is a disease of widespread occurrence in regions where corn, sweetcorn and popcorn are grown. This disease has great potential to cause damage and has been studied for years, but the association of its causal agent with seeds remains unconfirmed. Thus, the availability of a sensitive method to detect and quantify the inoculum in seeds, even at low incidence, is essential. The aim of this study was to develop a method to detect and quantify the presence of the fungus infecting and infesting corn and popcorn seeds. Artificially and naturally infected seeds were employed to develop the medium. The semi-selective medium was composed of carbendazim (active ingredient) (60 mg/L), captan (30 mg/L), streptomycin sulfate (500 mg/L) and neomycin sulfate (600 mg/L) aggregated to the medium lactose casein hydrolysate agar medium. By using this, Et was detected in naturally infected corn seeds, showing 0.124% incidence, in four out of ten analyzed samples. In addition, 1.04 conidia were detected per infested seed. By means of isolation, pathogenicity test, morphological characterization and comparison with descriptions of the species in the literature, the fungus isolated from the seeds was confirmed to be Et. Both infection and infestation were considered low; thus, for studies of Et detection in corn seeds, the use of semi-selective medium and more than 1,200 seeds/sample is suggested.

Switching components for medium voltage drives

Nowadays power drives are the essential part almost of all technological processes. Improvement of efficiency and reduction of losses require development of semiconductor switches. It has a particular meaning for the constantly growing market of renewable sources, especially for wind turbines, which demand more powerful semiconductor devices for control with growth of power. Also at present semiconductor switches are the key component in energy transmission, optimization of generation and network connection. The aim of this thesis is to make a survey of contemporary semiconductor components, showing difference in structures, advantages, disadvantages and most suitable applications. There is topical information about voltage, frequency and current limits of different switches. Study tries to compare dimensions and price of different components. Main manufacturers of semiconductor components are presented with the review of devices produced by them, and a conclusion about their availability was made. IGBT is selected as a main component in this study, because nowadays it is the most attractive component for usage in power drives, especially at the low levels of medium voltage. History of development of IGBT structure, static and dynamic characteristics are considered. Thesis tells about assemblies and connection of components and problems which can appear. One of key questions about semiconductor materials and their future development was considered. For the purpose of comparison strong and weak sides of different switches, calculation of losses of IGBT and its basic competitor – IGCT is presented. This master’s thesis makes an effort to answer the question if there are at present possibilities of accurate selection of switches for electrical drives of different rates of power and looks at future possible ways of development of semiconductor market.