Mechanical properties and comparisons of dynamic and static Young's moduli at DSDP Holes 69-504B, 70-504B and 83-504B

From laboratory tests under simulated downhole conditions we tentatively conclude that the higher the triaxial-compressive strength, the lower the drilling rate of basalts from DSDP Hole 504B. Because strength is roughly proportional to Young's modulus of elasticity, which is related in turn to seismic-wave velocities, one may be able to estimate drilling rates from routine shipboard measurements. However, further research is needed to verify that P-wave velocity is a generally useful predictor of relative drilling rate.

Composition of sediment pore water and isotopes in carbonate and benthic foraminifera at DSDP Holes 68-501, 69-505 and Site 69-504

Two sites on the southern flank of the Costa Rica Rift were drilled on DSDP Legs 68 and 69, one on crust 3.9 m.y. old and the other on crust 5.9 m.y. old. The basement of the younger site is effectively cooled by the circulation of seawater. The basement of the older site has been sealed by sediment, and an interval in the uppermost 560 meters of basement recently reheated to temperatures of 60 to 120°C. Although the thickness of the sediments at the two sites is similar (150-240 m versus 270 m), the much rougher basement topography at the younger Site 505 produces occasional basement outcrops, through which 80 to 90% of the total heat loss apparently occurs by advection of warm seawater. This seawater has been heated only slightly, however; the temperature at the base of the sediments is only 9°C. Changes in its composition due to reaction with the basement basalts are negligible, as indicated by profiles of sediment pore water chemistry. Bacterial sulfate reduction in the sediments produces a decrease in SO4 (and Ca) and an increase in alkalinity (and Sr and NH3) as depth increases to an intermediate level, but at deeper levels these trends reverse, and all of these species plus Mg, K, Na, and chlorinity approach seawater values near basement. Si, however, is higher, and Li may be lower. At the older site, Site 501/504, where heat loss is entirely by conduction, the temperature at the sediment/basement contact is 59°C. Sediment pore water chemistry is heavily affected by reaction with the basaltic basement, as indicated by large decreases in d18O, Mg, alkalinity, Na, and K and an increase in Ca with increasing depth. The size of the changes in d18O, Mg, alkalinity, Ca, Sr, and SO4 varies laterally over 500 meters, indicating lateral gradients in pore water chemistry that are nearly as large as the vertical gradients. The lateral gradients are believed to result from similar lateral gradients in the composition of the basement formation water, which propagate upward through the sediments by diffusion. A model of the d18O profile suggests that the basement at Site 501/504 was sealed off from advection about 1 m.y. ago, so that reaction rates began to dominate the basement pore water chemistry. A limestone-chert diagenetic front began to move upward through the lower sediments less than 200,000 yr. ago.

(Table 1) Physical properties of basalts from DSDP Legs 69 and 70

Physical properties of basalts from Deep Sea Drilling Project Sites 504 and 505, south of the Costa Rica Rift, including wet-bulk density, water content, sonic velocity, and thermal conductivity, were measured on board D/V Glomar Challenger during Legs 69 and 70. The mean wet-bulk density is 2.90±0.06 g/cm**3, porosity 5.0±2.2%, sonic velocity 5.75±0.30 km/s, and thermal conductivity 1.67±0.09 W/m°K. Basalts from this young ocean crust (5.9 m.y.) have relatively low porosity and consequently high density and sonic velocity, as compared to average DSDP basalts. Some systematic trends in depth variation of physical properties were found: down to Core 40 in Hole 504B, grain densities were lower than those deeper in the hole, whereas porosity in the upper section was higher. This can be attributed either to differences in the flow type or in the nature of alteration of basalts at the different levels in the hole.

(Table 1) Compressional-wave and shear-wave velocities and elastic constants from DSDP Legs 69 and 70

Shear-wave and compressional-wave velocities of 26 basalt samples collected at Site 504 during Deep Sea Drilling Project Legs 69 and 70 were measured at elevated confining pressures. The young basalts have higher velocities than average DSDP basalts, because of their lack of alteration. Measurements of sample porosity are combined with laboratory and in situ velocity measurements to yield estimates of total crustal porosity: 13% at the top of Layer 2, and very low porosity below a depth of 2.0 km.