Impacts of the application of swine wastewater in percolate and in soil cultivated with soybean

The aim of this study was to evaluate the possible impacts caused in the soil and in the percolate in lysimeters of drainage with application of different rates of swine wastewater (SW) during the cycle of soybean culture and to assess the productivity of it. The experiment was conducted at the Agricultural Engineering Experimental Center of UNIOESTE. The soil was classified as typical Distroferric Red Latosol. There were twenty-four drainage lysimeters in the area in which the soybean was cultivated, cultivar CD 214. Four SW depths (0; 100; 200 and 300 m³ ha-1) were applied to the soil seven days before the sowing in a single application combined with two mineral fertilizations in the sowing (with and without recommended fertilization during sowing), and three repetitions per treatment. It was realized three collections of percolate in each experimental portion, the first was conducted 40 days after sowing (DAS); the second at 72 DAS, and the third at the end of crop cycle (117 DAS). It was evaluated in the percolate the pH, calcium, magnesium, potassium, phosphorus, and total nitrogen. Based on the results, it was possible to observe that the level of K, P and N in the soil increased according tothe increase of SW rates. The levels of K and P in the percolate were higher for higher rates of SW. The productivity was not influenced by the application of SW or by fertilization.

Anaerobic reactors with biofilter and different diameter-length ratios in cassava starch industry wastewater treatment

The use of anaerobic reactors with media support in the treatment of wastewater from the cassava starch industry has emerged as a viable option because it allows the application of high organic loads and a significant reduction of the HDT needed for the treatment. This research aimed at studying the process of biodigestion in two anaerobic reactors with bamboo support, in the treatment of effluent of cassava starch, by evaluating their performance. The two reactors used present the following diameter: length ratio, 1:6 and 1:3. The organic loads applied to the systems were 0.519, 1.156, 1.471, 3.049, 4.347, 4.708 and 5.601g.L-1.d-1. Regarding the efficiency of removal of COD, TS and TVS, no statistically significant differences were obtained between the reactors. The two systems evaluated showed a stable behavior with respect to the VA/TA (volatile acidity/total alkalinity) for all submitted loads. The reactors tended to the maintenance of biogas production as a function of consumed COD for the last three organic loads applied, indicating an ability to withstand higher organic loads.

Evaluation of the effect of the seed extract of Moringa oleifera Lam over the efficiency of organic filters in wastewater treatment of dairy cattle breeding

This study aimed to evaluate the effect of Moringa oleifera Lam extract on the removal of total solids (TS), total suspended solids (TSS) and chemical oxygen demand (COD), in different filter media for treating wastewater of dairy cattle breeding (DCW). The moringa seed extract was obtained by grinding 50 g of seeds in one liter of distilled water and, after passing the solution through a quantitative paper filter of 25 microns, 60 mL of the extract were added to wastewater from cattle breeding before the filtration process in organic filters made of thin coal, bamboo leaves, eucalyptus leaves, gliricidia branches and sawdust. This was followed by the completely randomized experimental design, adopting a factorial of 5 x 2. Aliquots of filtered effluent were collected and the total solids (TS) concentrations, total suspended solids (TSS) and chemical oxygen demand (COD) were determined. It was found that the increase in the efficiency of removal of COD and total solids can be attributed to the coagulating power of the moringa seed extract, wherein the filter medium with bamboo leaves presented the best performance, showing potential for use as alternative filter material in the primary treatment of DCW.

Swine wastewater associated with mineral fertilization on corn crop (Zea mays)

This study aimed to evaluate the agronomical and environmental aspects in corn, soil characteristics and leachate resulting from the material combination of swine wastewater and mineral fertilizer in the long run. The experimental area has a history of swine wastewater application for experiments conducted since 2006, this being the seventh crop cycle in the area. Four doses of swine wastewater (0; 100; 200 and 300 m³ ha-1) associated with presence and absence of mineral fertilizer were applied, consisting of eight treatments. The results obtained were subjected to variance analysis and means compared by Tukey test at 5% significance. We conclude that the swine wastewater can be partially used as an alternative fertilizer, since the P and Mn are complemented with specific fertilization. There must be carefulness about Fe+2, Cu+2 and Zn+2 accumulation in soil, and also to the concentrations of Fe+2, Cu+2, Zn+2, NO3- + NO2- and Na+ in leachate which exceeded the limits at the highest SWW applied levels.

Chemical attributes of soil and dry mass accumulation of maize fertilized with cassava wastewater

The aim of this study was to evaluate chemical attributes alterations of a clay-loam textured soil and dry mass accumulation of maize submitted to application of cassava wastewater doses in three assessment periods. The experiment was conducted under greenhouse using a completely randomized experimental design in a factorial 5 × 3, with four replicates. The analyzed factors of research were doses of cassava wastewater (0; 12.6; 25.2; 50.4; 75.6 m3 ha-1) andassessment periods (20, 40 and 52 days after germination). The following parameters were determined: electric conductivity of soil saturation extract, pH in water, content of available P, content of exchangeable K+, Ca2+, Mg2+ and Na+of soil, dry mass of leaves and stem. The application of cassava wastewater on soil enables increase of pH, electric conductivity of saturation extract, contents of available P, contents of exchangeable K+ and Na+ and dry mass of leaves and stem. However, only pH and content of exchangeable K+ of soil, the electric conductivity of saturation extract and dry mass of leaves and stem are influenced by assessment period.

Hydrogen production from cassava processing wastewater in an anaerobic fixed bed reactor with bamboo as a support material

Attempting to associate waste treatment to the production of clean and renewable energy, this research sought to evaluate the biological production of hydrogen using wastewater from the cassava starch treatment industry, generated during the processes of extraction and purification of starch. This experiment was carried out in a continuous anaerobic reactor with a working volume of 3L, with bamboo stems as the support medium. The system was operated at a temperature of 36°C, an initial pH of 6.0 and under variations of organic load. The highest rate of hydrogen production, of 1.1 L.d-1.L-1, was obtained with application of an organic loading rate of 35 g.L-1.d-1, in terms of total sugar content and hydraulic retention time of 3h, with a prevalence of butyric and acetic acids as final products of the fermentation process. Low C/N ratios contributed to the excessive growth of the biomass, causing a reduction of up to 35% in hydrogen production, low percentages of H2 and high concentrations of CO2in the biogas.

Production of natural aroma by yeast in wastewater of cassava starch industry

ABSTRACT2-Phenylethanol (PE) is an aromatic alcohol with a characteristic odor of roses, widely used in food industry to modify certain aroma compositions in formulations with fruit, jam, pudding, and chewing gums, and also in cosmetic and fragrance industry. This compound occurs naturally in low concentrations in some essential oils from flowers and plants. An alternative to plants extraction are biotechnological processes. This study evaluated 2-phenylethanol’s production in cultivation of Saccharomyces cerevisiae in cassava wastewater originated from starch industry. The substrate was supplemented with glucose and L-phenylalanine in order to obtain higher 2-phenylethanol concentrations and better efficiency in glucose/2-phenylethanol conversion. It was performed using Rotatable Center Composite Design and response surface analysis. Cultures were performed under aerobic conditions in a batch system in Erlenmeyer flasks containing 50 mL of medium in shaker at 150 rpm and 24 ± 1 ºC. The highest PE values ​​were obtained with supplementation of 20.0 g.L-1 of glucose and 5.5 g.L-1 of L-phenylalanine, which has been experimentally validated, obtaining a PE production of 1.33 g.L-1 and PE/glucose yield factor of 0.070 g.g-1, equivalent to 74.3 and 89.7% ​​of desirability values according to the validated model.

Soil physical attributes in chemigated banana plantation with wastewater

ABSTRACT The feasibility of using sewage wastewater as a water and nutrient source for plants is an alternative to harness agricultural natural resource, observing its influence on the organic matter dynamics and soil energy. Our objective here was to evaluate the effects of applying different doses of effluent from a sewage treatment plant, in Janaúba – MG, Brazil, over the physical attributes of a soil grown with “Prata Anã” banana. From soil sample collection at depths of 0-20, 20-40, and 40-60 cm, we determined the following soil properties: soil density, total porosity, macroporosity, microporosity, organic matter, clay dispersed in water and stability of soil aggregate. The experimental design was in randomized blocks with four repetitions. Wastewater raising doses promoted increase in suspended solids, contributing to macroporosity reduction at 20-40 and 40-60 cm depths; as well as a reduction in organic matter within 0-20 cm layer. Clay dispersal was observed in the depths of 0-20 cm, being derived from an increase in sodium content. Concurrently, there was a reduction of soil aggregate stability.

CHARACTERIZATION AND EVALUATION OF THE POTENTIAL USE OF SLUDGE FROM STP AND WTP IN PAVING

ABSTRACT Water and sewage treatment plants (STP and WTP) generate as byproduct a significant amount of sludge with environment harmful elements. Sending to landfills or depositing on the ground or rivers are respectively expensive and dangerous alternatives. In this scenario, the use of this waste in paving processes is a promising alternative for disposal thereof. In this study, we focused on characterizing sludge and evaluating its use in paving, which showed satisfactory results for use in base and sub-base floors.

LONG-TERM EFFECTS OF SWINE wastewater AND MINERAL FERTILIZER ASSOCIATION ON SOIL MICROBIOTA

ABSTRACT Swine wastewater (SW) application in agricultural soils may affect its microbial community in a long term. The objective of this study was to evaluate prospective changes in soil bacterial community after eight years continuous application of swine wastewater. The wastewater doses tested were 0; 100; 200 and 300 m3 ha-1, being applied from the beginning of the experiment and with or without recommended fertilization. Three soil samples were taken from each plot for determinations of basal respiration, microbial biomass and metabolic quotient. We also performed DGGE analysis and made a correlation between soil chemical conditions and microbial activity. Microbial community underwent significant structural changes from swine wastewater applications. Higher SW doses (200 and 300 m3 ha-1) influenced significantly (p <0.05) and benefitted certain bacteria groups.

Feasibility of ASH DEC‐ process in treating sewage sludge and manure ash in Finland

In Finland the thermal treatment of sewage sludge has been moderate in 21th century. The reason has been the high moisture content of sludge. During 2005-2008, 97-99% of sewage sludge was utilized in landscaping and agriculture. However agricultural use has been during 2005-2007 less than 3 %. The aim of national waste management plan is that by 2016 100% of sludge is used either as soil amendment or energy. The most popular utilization method for manure is spreading it on arable land. The dry manures such as poultry manure and horse manure could also be used in incineration. The ashes could be used as fertilizers and while it is not suitable as a starter fertilizer, it is suitable in maintaining P levels in the soil. One of the main drivers for more efficient nutrient management is the eutrophication in lakes and the Baltic See. ASH DEC process can be used in concentrating phosphorus rich ashes while separating the heavy metals that could be included. ASH DEC process uses thermochemical treatment to produce renewable phosphate for fertilizer production. The process includes mixing of ashes and chlorine donors and subsequent treatment in rotary kiln for 20 min in temperature of 900 – 1 050 oC. The heavy metals evaporate and P-rich product is obtained. The toxic substances are retained in air pollution control system in form of mixed metal hydroxides. The aim of conducting this study is to estimate the potential of ASH DEC process in treating phosphorus rich ashes in Finland. The masses considered in are sewage sludge, dry manure from horses, and poultry and liquid pig manure. To date the usual treatment method for sewage sludge in Finland is composting or anaerobic digestion. Part of the amount of produced sewage sludge (800 kt/a fresh mass and 160 kt/a TS) could also be incinerated and the residual ashes used in ASH DEC process. Incinerating only manure can be economically difficult to manage because the incineration of manure is in Finland considered as waste incineration. Getting a permit for waste incineration is difficult and also small scale waste incineration is too expensive. The manure could act as an additional feedstock in counties with high density of animal husbandry where the land area might not be enough for spreading of manure. Now when the manure acts as a supplementary feedstock beside sludge, the ash can’t be used directly as fertilizer. Then it could be used in ASH DEC process. The perquisite is that the manure producers could pay for the incineration, which might prove problematic.

Käänteisosmoosin esikäsittelymenetelmät

Käänteisosmoosisuodatusta käytetään erityisesti teollisuuden jätevesien loppupuhdistuksessa. Suodatuksen ongelmana on kalvojen likaantuminen ja tukkiutuminen. Tässä työssä on aiempia tutkimuksia hyväksikäyttäen tutkittu käänteisosmoosiin tulevan veden esikäsittelemistä niin, että kalvojen likaantumiselta vältyttäisiin. Menetelmien vertailussa on käytetty erilaisia veden laadusta kertovia parametreja. Ongelmallisimmiksi aineksiksi huomattiin orgaaninen aines ja jotkin veteen liuenneet ionit. Kiintoaineen erottaminen ei ole ollut suuri ongelma, sillä sen saa poistettua tavallisesti käytetyillä rakeissuodatuksella, laskeutuksella, flotaatiolla ja kalvosuodatuksella. Orgaanista ainesta on saatu erotettua erityisesti hapettamalla, aktiivilieteprosessilla ja biologisella aktiivihiilisuodattimella. Mikro- ja ultrasuodatusta käytetään usein juuri ennen käänteisosmoosia poistamaan erityisesti kolloidista materiaalia ja joitain liuenneita ioneja. Flokkien muodostaminen koagulaatiossa ja flokkulaatiossa parantaa lähes kaikkien menetelmien toimivuutta selvästi. Veden puhdistuksessa käytetyt kemikaalit voivat myös liika-annosteltuina liata kalvoja. Vesien pitoisuuksissa eri ainesten osalta on huomattavia eroja, joten puhdistettava vesi on hyvä analysoida etukäteen parhaiden käsittelymenetelmien valitsemiseksi.

Industrial-Scale hydrothermal carbonization of waste sludge materials for fuel production

Hydrothermal carbonization (HTC) is a thermochemical process used in the production of charred matter similar in composition to coal. It involves the use of wet, carbohydrate feedstock, a relatively low temperature environment (180 °C-350 °C) and high autogenous pressure (up to 2,4 MPa) in a closed system. Various applications of the solid char product exist, opening the way for a range of biomass feedstock materials to be exploited that have so far proven to be troublesome due to high water content or other factors. Sludge materials are investigated as candidates for industrial-scale HTC treatment in fuel production. In general, HTC treatment of pulp and paper industry sludge (PPS) and anaerobically digested municipal sewage sludge (ADS) using existing technology is competitive with traditional treatment options, which range in price from EUR 30-80 per ton of wet sludge. PPS and ADS can be treated by HTC for less than EUR 13 and 33, respectively. Opportunities and challenges related to HTC exist, as this relatively new technology moves from laboratory and pilot-scale production to an industrial scale. Feedstock materials, end-products, process conditions and local markets ultimately determine the feasibility of a given HTC operation. However, there is potential for sludge materials to be converted to sustainable bio-coal fuel in a Finnish context.

International Advanced Water Technologies Centre, IAWTC/LADEC and LUT 2013 : Questionnaire Responses from Russian Drinking Water and Wastewater Treatment Plants

In this report, information is published concerning Russian water and wastewater treatment plants. The information is based on a questionnaire sent to 70 water and wastewater treatment plants in 2012-2013. The questionnaire was prepared by the International Advanced Water Technologies Centre (IAWTC) and Lahti Development Company (LADEC). The questions dealt with an assessment of the present state, the need for changes, renovation, investments, and how to improve the efficiency of the operation by training and investments. A significant need to renew the old pipelines, constructions, and processes was clearly evident. The aggregated answers can be utilized in Russia as internal benchmarking in order to arrange training and plant visits, which were requested in many of the answers. Sharing this open report with the respondents can aid networking and awareness of HELCOM requirements which relate to waste water treatment plants discharging their waste water directly or indirectly into the Baltic Sea. The aim of this report is to provide information for Finnish small and medium size companies (SMEs) as regards possible water related exportation to different parts of Russia.

CFD modeling of dispersion water feed in wastewater cleaning application

Fluid particle breakup and coalescence are important phenomena in a number of industrial flow systems. This study deals with a gas-liquid bubbly flow in one wastewater cleaning application. Three-dimensional geometric model of a dispersion water system was created in ANSYS CFD meshing software. Then, numerical study of the system was carried out by means of unsteady simulations performed in ANSYS FLUENT CFD software. Single-phase water flow case was setup to calculate the entire flow field using the RNG k-epsilon turbulence model based on the Reynolds-averaged Navier-Stokes (RANS) equations. Bubbly flow case was based on a computational fluid dynamics - population balance model (CFD-PBM) coupled approach. Bubble breakup and coalescence were considered to determine the evolution of the bubble size distribution. Obtained results are considered as steps toward optimization of the cleaning process and will be analyzed in order to make the process more efficient.