Diode-clamped three-level inverter-based battery/supercapacitor direct integration scheme for renewable energy systems

This paper describes a diode-clamped three-level inverter-based battery/supercapacitor direct integration scheme for renewable energy systems. The study is carried out for three different cases. In the first case, one of the two dc-link capacitors of the inverter is replaced by a battery bank and the other by a supercapacitor bank. In the second case, dc-link capacitors are replaced by two battery banks. In the third case, ordinary dc-link capacitors are replaced by two supercapacitor banks. The first system is supposed to mitigate both long-term and short-term power fluctuations while the last two systems are intended for smoothening long-term and short-term power fluctuations, respectively. These topologies eliminate the need for interfacing dc-dc converters and thus considerably improve the overall system efficiency. The major issue in aforementioned systems is the unavoidable imbalance in dc-link voltages. An analysis on the effects of unbalance and a space vector modulation method, which can produce undistorted current even in the presence of such unbalances, are presented in this paper. Furthermore, small vector selection-based power sharing and state of charge balancing techniques are proposed. Experimental results, obtained from a laboratory prototype, are presented to verify the efficacy of the proposed modulation and control techniques.

Design of a robust grid interface system for PMSG-based wind turbine generators

A robust and reliable grid power interface system for wind turbines using a permanent-magnet synchronous generator (PMSG) is proposed in this paper, where an integration of a generator-side three-switch buck-type rectifier and a grid-side Z-source inverter is employed as a bridge between the generator and the grid. The modulation strategy for the proposed topology is developed from space-vector modulation and Z-source network operation principles. Two PMSG control methods, namely, unity-power-factor control and rotor-flux-orientation control (Id = 0), are studied to establish an optimized control scheme for the generator-side three-switch buck-type rectifier. The system control scheme decouples active- and reactive-power control through voltage-oriented control and optimizes PMSG control for the grid- and generator-side converters independently. Maximum power point tracking is implemented by adjusting the shoot-through duty cycles of the Z-source network. The design considerations of the passive components are also provided. The performances and practicalities of the designed architecture have been verified by simulations and experiments.

Spontaneous large volume adipose tissue generation from a vascularized pedicled fat flap inside a chamber space

A novel method of spontaneous generation of new adipose tissue from an existing fat flap is described. A defined volume of fat flap based on the superficial inferior epigastric vascular pedicle in the rat was elevated and inset into a hollow plastic chamber implanted subcutaneously in the groin of the rat. The chamber walls were either perforated or solid and the chambers either contained poly(D,L-lactic-co-glycolic acid) (PLGA) sponge matrix or not. The contents were analyzed after being in situ for 6 weeks. The total volume of the flap tissue in all groups except the control groups, where the flap was not inserted into the chambers, increased significantly, especially in the perforated chambers (0.08 ± 0.007 mL baseline compared to 1.2 ± 0.08 mL in the intact ones). Volume analysis of individual component tissues within the flaps revealed that the adipocyte volume increased and was at a maximum in the chambers without PLGA, where it expanded from 0.04 ± 0.003 mL at insertion to 0.5 ± 0.08 mL (1250% increase) in the perforated chambers and to 0.16 ± 0.03 mL (400% increase) in the intact chambers. Addition of PLGA scaffolds resulted in less fat growth. Histomorphometric analysis rather than simple hypertrophy documented an increased number of adipocytes. The new tissue was highly vascularized and no fat necrosis or atypical changes were observed.

The QUT innovation space : a trans-disciplinary learning environment for entrepreneurship education : final report

In the current climate of global economic volatility, there are increasing calls for training in enterprising skills and entrepreneurship to underpin the systemic innovation required for even medium-term business sustainability. The skills long-recognised as the essential for entrepreneurship now appear on the list of employability skills demanded by industry. The QUT Innovation Space (QIS) was an experiment aimed at delivering entrepreneurship education (EE), as an extra-curricular platform across the university, to the undergraduate students of an Australian higher education institute. It was an ambitious project that built on overseas models of EE studied during an Australian Learning and Teaching Council (ALTC) Teaching Fellowship (Collet, 2011) and implemented those approaches across an institute. Such EE approaches have not been attempted in an Australian university. The project tested resonance not only with the student population, from the perspective of what worked and what didn’t work, but also with every level of university operations. Such information is needed to inform the development of EE in the Australian university landscape. The QIS comprised a physical co-working space, virtual sites (web, Twitter and Facebook) and a network of entrepreneurial mentors, colleagues, and students. All facets of the QIS enabled connection between like-minded individuals that underpins the momentum needed for a project of this nature. The QIS became an innovation community within QUT. This report serves two purposes. First, as an account of the QIS project and its evolution, the report serves to identify the student demand for skills and training as well as barriers and facilitators of the activities that promote EE in an Australian university context. Second, the report serves as a how-to manual, in the tradition of many tomes on EE, outlining the QIS activities that worked as well as those that failed. The activities represent one measure of QIS outcomes and are described herein to facilitate implementation in other institutes. The QIS initially aimed to adopt an incubation model for training in EE. The ‘learning by doing’ model for new venture creation is a highly successful and high profile training approach commonly found in overseas contexts. However, the greatest demand of the QUT student population was not for incubation and progression of a developed entrepreneurial intent, but rather for training that instilled enterprising skills in the individual. These two scenarios require different training approaches (Fayolle and Gailly, 2008). The activities of the QIS evolved to meet that student demand. In addressing enterprising skills, the QIS developed the antecedents of entrepreneurialism (i.e., entrepreneurial attitudes, motivation and behaviours) including high-level skills around risk-taking, effective communication, opportunity recognition and action-orientation. In focusing on the would-be entrepreneur and not on the (initial) idea per se, the QIS also fostered entrepreneurial outcomes that would never have gained entry to the rigid stage-gated incubation model proposed for the original QIS framework. Important lessons learned from the project for development of an innovation community include the need to: 1. Evaluate the context of the type of EE program to be delivered and the student demand for the skills training (as noted above). 2. Create a community that builds on three dimensions: a physical space, a virtual environment and a network of mentors and partners. 3. Supplement the community with external partnerships that aid in delivery of skills training materials. 4. Ensure discovery of the community through the use of external IT services to deliver advertising and networking outlets. 5. Manage unrealistic student expectations of billion dollar products. 6. Continuously renew and rebuild simple activities to maintain student engagement. 7. Accommodate the non-university end-user group within the community. 8. Recognise and address the skills bottlenecks that serve as barriers to concept progression; in this case, externally provided IT and programming skills. 9. Use available on-line and published resources rather than engage in constructing project-specific resources that quickly become obsolete. 10. Avoid perceptions of faculty ownership and operate in an increasingly competitive environment. 11. Recognise that the continuum between creativity/innovation and entrepreneurship is complex, non-linear and requires different training regimes during the different phases of the pipeline. One small entity, such as the QIS, cannot address them all. The QIS successfully designed, implemented and delivered activities that included events, workshops, seminars and services to QUT students in the extra-curricular space. That the QIS project can be considered successful derives directly from the outcomes. First, the QIS project changed the lives of emerging QUT student entrepreneurs. Also, the QIS activities developed enterprising skills in students who did not necessarily have a business proposition, at the time. Second, successful outcomes of the QIS project are evidenced as the embedding of most, perhaps all, of the QIS activities in a new Chancellery-sponsored initiative: the Leadership Development and Innovation Program hosted by QUT Student Support Services. During the course of the QIS project, the Brisbane-based innovation ecosystem underwent substantial change. From a dearth of opportunities for the entrepreneurially inclined, there is now a plethora of entities that cater for a diversity of innovation-related activities. While the QIS evolved with the landscape, the demand endpoint of the QIS activities still highlights a gap in the local and national innovation ecosystems. The freedom to experiment and to fail is not catered for by the many new entities seeking to build viable businesses on the back of the innovation push. The onus of teaching the enterprising skills, which are the employability skills now demanded by industry, remains the domain of the higher education sector.

Design methodologies and architectures of hardware-based evolutionary algorithms for aerospace optimisation applications on FPGAS

This thesis is a study of new design methods for allowing evolutionary algorithms to be more effectively utilised in aerospace optimisation applications where computation needs are high and computation platform space may be restrictive. It examines the applicability of special hardware computational platforms known as field programmable gate arrays and shows that with the right implementation methods they can offer significant benefits. This research is a step forward towards the advancement of efficient and highly automated aircraft systems for meeting compact physical constraints in aerospace platforms and providing effective performance speedups over traditional methods.

Modelling airport passenger group dynamics using an agent-based method

This thesis investigates the influence of passenger group dynamics on passengers' behaviour in an international airport. A simulation model is built to analyse passengers' behaviour during airport departure processes and during an emergency event. Results from the model showed that passengers' group dynamics have significant influences on the performance and utilisation of airport services. The agent-based model also provides a convenient way to investigate the effectiveness of space design and service allocations, which may contribute to the enhancement of passenger airport experiences.

Monitoring spatiotemporal dynamics of human movement based on MAC address data

This thesis was a step forward in extracting valuable features from human's movement behaviour in terms of space utilisation based on Media-Access-Control data. This research offered a low-cost and less computational complexity approach compared to existing human's movement tracking methods. This research was successfully applied in QUT's Gardens Point campus and can be scaled to bigger environments and societies. Extractable information from human's movement by this approach can add a significant value to studying human's movement behaviour, enhancing future urban and interior design, improving crowd safety and evacuation plans.

Knowledge Based Urban Development

The changing and challenging conditions of the 21st century have been significantly impacting our economy, society and built and natural environments. Today generation of knowledge—mostly in the form of technology and innovation—is seen as a panacea for the adaptation to changes and management of challenges (Yigitcanlar, 2010a). Making space and place that concentrate on knowledge generation, thus, has become a priority for many nations (van Winden, 2010). Along with this movement, concepts like knowledge cities and knowledge precincts are coined as places where citizenship undertakes a deliberate and systematic initiative for founding its development on the identification and sustainable balance of its shared value system, and bases its ability to create wealth on its capacity to generate and leverage its knowledge capabilities (Carrillo, 2006; Yigitcanlar, 2008a). In recent years, the term knowledge precinct (Hu & Chang, 2005) in its most contemporary interpretation evolved into knowledge community precinct (KCP). KCP is a mixed-use post-modern urban setting—e.g., flexible, decontextualized, enclaved, fragmented—including a critical mass of knowledge enterprises and advanced networked infrastructures, developed with the aim of collecting the benefits of blurring the boundaries of living, shopping, recreation and working facilities of knowledge workers and their families. KCPs are the critical building blocks of knowledge cities, and thus, building successful KCPs significantly contributes to the formation of prosperous knowledge cities. In the literature this type of development—a place containing economic prosperity, environmental sustainability, just socio‐spatial order and good governance—is referred as knowledge-based urban development (KBUD). This chapter aims to provide a conceptual understanding on KBUD and its contribution to the building of KCPs that supports the formation of prosperous knowledge cities.

SCRAMSPACE : Radical-Farming Scramjet for access to space

Scramjet-based launch systems offer considerable promise for safe, reliable and economical access to space. A general Scramjets introduction is first provided, followed by the specifics of Australian Scramjet Research and the recent progress in inlet-injection radical-farming scramjets as part of the SCRAMSPACE program. Through both flight and ground tests, leveraging Australias world leadership in scramjet R&D, the SCRAMSPACE project is designed to answer key scientific and technological questions and build an industry-ready talent pool for a future Australian space industry. An extensive descriptions of all phases of the development of the SCRAMSPACE I scramjet-powered free-flight experiment are described in these lecture notes.

Numerical simulation of self-organized nano-islands in plasma-based assembly of quantum dot arrays

This work presents the details of the numerical model used in simulation of self-organization of nano-islands on solid surfaces in plasma-assisted assembly of quantum dot structures. The model includes the near-substrate non-neutral layer (plasma sheath) and a nanostructured solid deposition surface and accounts for the incoming flux of and energy of ions from the plasma, surface temperature-controlled adatom migration about the surface, adatom collisions with other adatoms and nano-islands, adatom inflow to the growing nano-islands from the plasma and from the two-dimensional vapour on the surface, and particle evaporation to the ambient space and the two-dimensional vapour. The differences in surface concentrations of adatoms in different areas within the quantum dot pattern significantly affect the self-organization of the nano-islands. The model allows one to formulate the conditions when certain islands grow, and certain ones shrink or even dissolve and relate them to the process control parameters. Surface coverage by selforganized quantum dots obtained from numerical simulation appears to be in reasonable agreement with the available experimental results.

Defining the spatiotemporal surveillance space for alien species’ invasions using approximate Bayesian computation

The spatiotemporal dynamics of an alien species invasion across a real landscape are typically complex. While surveillance is an essential part of a management response, planning surveillance in space and time present a difficult challenge due to this complexity. We show here a method for determining the highest probability sites for occupancy across a landscape at an arbitrary point in the future, based on occupancy data from a single slice in time. We apply to the method to the invasion of Giant Hogweed, a serious weed in the Czech republic and throughout Europe.

Dual inverter based battery energy storage system for grid connected photovoltaic systems

This paper explores a new breed of energy storage system interfacing for grid connected photovoltaic (PV) systems. The proposed system uses the popular dual inverter topology in which one inverter is supplied by a PV cell array and the other by a Battery Energy Storage System (BESS). The resulting conversion structure is controlled in a way that both demand matching and maximum power point tracking of the PV cell array are performed simultaneously. This dual inverter topology can produces 2, 3, 4 and 5 level inverter voltage waveforms at the dc-link voltage ratios of 0:1, 1:1, 2:1 and 3:2 respectively. Since the output voltage of the PV cell array and the battery are uncorrelated and dynamically change, the resulting dc-link voltage ratio can take non-integer values as well. These noninteger dc-link voltage ratios produce unevenly distributed space vectors. Therefore, the main issue with the proposed system is the generation of undistorted current even in the presence of unevenly distributed and dynamically changing space vectors. A modified space vector modulation method is proposed in this paper to address this issue and its efficacy is proved by simulation results. The ability of the proposed system to act as an active power source is also verified.

Time, space, and text in the elementary school digital writing classroom

Theorists of multiliteracies, social semiotics, and the New Literacy Studies have drawn attention to the potential changing nature of writing and literacy in the context of networked communications. This article reports findings from a design-based research project in Year 4 classrooms (students aged 8.5-10 years) in a low socioeconomic status school. A new writing program taught students how to design multimodal and digital texts across a range of genres and text types, such as web pages, online comics, video documentaries, and blogs. The authors use Bernstein’s theory of the pedagogic device to theorize the pedagogic struggles and resolutions in remaking English through the specialization of time, space, and text. The changes created an ideological struggle as new writing practices were adapted from broader societal fields to meet the instructional and regulative discourses of a conventional writing curriculum.

Bayesian hierarchical models for analysing spatial point-based data at a grid level: A comparison of approaches

Spatial data are now prevalent in a wide range of fields including environmental and health science. This has led to the development of a range of approaches for analysing patterns in these data. In this paper, we compare several Bayesian hierarchical models for analysing point-based data based on the discretization of the study region, resulting in grid-based spatial data. The approaches considered include two parametric models and a semiparametric model. We highlight the methodology and computation for each approach. Two simulation studies are undertaken to compare the performance of these models for various structures of simulated point-based data which resemble environmental data. A case study of a real dataset is also conducted to demonstrate a practical application of the modelling approaches. Goodness-of-fit statistics are computed to compare estimates of the intensity functions. The deviance information criterion is also considered as an alternative model evaluation criterion. The results suggest that the adaptive Gaussian Markov random field model performs well for highly sparse point-based data where there are large variations or clustering across the space; whereas the discretized log Gaussian Cox process produces good fit in dense and clustered point-based data. One should generally consider the nature and structure of the point-based data in order to choose the appropriate method in modelling a discretized spatial point-based data.

Representation of facial expression categories in continuous arousal-valence space: Feature and correlation

Representation of facial expressions using continuous dimensions has shown to be inherently more expressive and psychologically meaningful than using categorized emotions, and thus has gained increasing attention over recent years. Many sub-problems have arisen in this new field that remain only partially understood. A comparison of the regression performance of different texture and geometric features and investigation of the correlations between continuous dimensional axes and basic categorized emotions are two of these. This paper presents empirical studies addressing these problems, and it reports results from an evaluation of different methods for detecting spontaneous facial expressions within the arousal-valence dimensional space (AV). The evaluation compares the performance of texture features (SIFT, Gabor, LBP) against geometric features (FAP-based distances), and the fusion of the two. It also compares the prediction of arousal and valence, obtained using the best fusion method, to the corresponding ground truths. Spatial distribution, shift, similarity, and correlation are considered for the six basic categorized emotions (i.e. anger, disgust, fear, happiness, sadness, surprise). Using the NVIE database, results show that the fusion of LBP and FAP features performs the best. The results from the NVIE and FEEDTUM databases reveal novel findings about the correlations of arousal and valence dimensions to each of six basic emotion categories.