A "Free-Lunch" tour of the Jovian System

An ED-tether mission to Jupiter is presented. A bare tether carrying cathodic devices at both ends but no power supply, and using no propellant, could move 'freely' among Jupiter's 4 great moons. The tour scheme would have current naturally driven throughout by the motional electric field, the Lorentz force switching direction with current around a 'drag' radius of 160,00 kms, where the speed of the jovian ionosphere equals the speed of a spacecraft in circular orbit. With plasma density and magnetic field decreasing rapidly with distance from Jupiter, drag/thrust would only be operated in the inner plasmasphere, current being near shut off conveniently in orbit by disconnecting cathodes or plugging in a very large resistance; the tether could serve as its own power supply by plugging in an electric load where convenient, with just some reduction in thrust or drag. The periapsis of the spacecraft in a heliocentric transfer orbit from Earth would lie inside the drag sphere; with tether deployed and current on around periapsis, magnetic drag allows Jupiter to capture the spacecraft into an elliptic orbit of high eccentricity. Current would be on at succesive perijove passes and off elsewhere, reducing the eccentricity by lowering the apoapsis progressively to allow visits of the giant moons. In a second phase, current is on around apoapsis outside the drag sphere, rising the periapsis until the full orbit lies outside that sphere. In a third phase, current is on at periapsis, increasing the eccentricity until a last push makes the orbit hyperbolic to escape Jupiter. Dynamical issues such as low gravity-gradient at Jupiter and tether orientation in elliptic orbits of high eccentricity are discussed.

Efficiency of electrodynamic tether thrusters

The performance efficiency of electrodynamic bare tethers acting as thrusters in low Earth orbit, as gauged by the ratio of the system mass dedicated to thrust over mission impulse, is analyzed and compared to the performance efficiency of electrical thrusters. Tether systems are much lighter for times beyond six months in space-tug operations, where there is a dedicated solar array, and beyond one month for reboost of the International Space Station, where the solar array is already in place. Bare-tether propulsive efficiency itself, with the tether considered as part of the power plant, is higher for space tugs. Tether optimization shows that thin tapes have greater propulsive efficiency and are less sensitive to plasma density variations in orbit than cylindrical tethers. The efficiency increases with tape length if some segment next to the power supply at the top is insulated to make the tether potential bias vanish at the lower end; multitape tethers must be used to keep the efficiency high at high thrust levels. The efficiency has a maximum for tether-hardware mass equal to the fraction of power-subsystem mass going into ohmic power, though the maximum is very flat. For space tugs, effects of induced-bias changes in orbit might need to be reduced by choosing a moderately large power-subsystem to tether-hardware mass ratio or by tracking the current-voltage characteristic of the solar array.

Floating Bare Tether as Upper Atmosphere Probe

Use of a (bare) conductive tape electrically floating in LEO as an effective e-beam source that produces artificial auroras, and is free of problems that have marred standard beams, is considered. Ambient ions impacting the tape with KeV energies over most of its length liberate secondary electrons, which race down the magnetic field and excite neutrals in the E-layer, resulting in auroral emissions. The tether would operate at night-time with both a power supply and a plasma contactor off; power and contactor would be on at daytime for reboost. The optimal tape thickness yielding a minimum mass for an autonomous system is determined; the alternative use of an electric thruster for day reboost, depending on mission duration, is discussed. Measurements of emission brightness from the spacecraft could allow determination of the (neutral) density vertical profile in the critical E-layer; the flux and energy in the beam, varying along the tether, allow imaging line-of-sight integrated emissions that mix effects with altitude-dependent neutral density and lead to a brightness peak in the beam footprint at the E-layer. Difficulties in tomographic inversion, to determine the density profile, result from beam broadening, due to elastic collisions, which flattens the peak, and to the highly nonlinear functional dependency of line-of-sight brightness. Some dynamical issues are discussed.

Aplicación de energía geotérmica de muy baja entalpia para la climatización de un edificio de oficinas en Alcorcón, Madrid

El presente Proyecto tiene como propósito el estudio de la viabilidad de la implantación de energía geotérmica de muy baja entalpia para la climatización de un edificio empresarial en Madrid. Para ello se emplearon cálculos teóricos y simulaciones realizadas mediante programas informaticos especializados con el fin de estimar los parámetros técnicos necesarios para su viabilidad. Se estimo el suministro de la potencia necesaria a través de tres bombas de calor tipo agua-agua que sustituyen a las bombas de calor aire-agua individuales anteriormente instaladas. El intercambio de calor se realiza a través de sondas geotérmicas U-Simple. Se dimensionaron los colectores, bombas de circulación, deposito de inercia y vaso de expansión necesarios para funcionamiento del sistema. El estudio económico determino la necesidad de una alta inversión inicial, con una rentabilidad a medio plazo. Además de los beneficios económicos se realizo un estudio de las emisiones de gases de efecto invernadero demostrando la reducción de los mismos, lo que refleja que además de ser una tecnología económicamente viable es una energía limpia. ABSTRACT The objective of the present project is to evaluate the viability of the imposition of a low-enthalpy geothermal energy system for air conditioning in a business building in Madrid. In this study, both theoretical calculations and numerical simulations in specialized programs were used in order to estimate the technical parameters needed for its viability. We estimated the necessary power supply, which is delivered by three heat water-water pumps that substitute the individual heat air-water pumps previously installed. The heat exchange is achieved through geothermal vertical simple-U probes. Also in this work we have measured the collectors, flow pumps, inertia deposit and the water expansion vessel needed for the proper operation of the system. The economic study determined the need of a high initial investment with mid-term profit. In addition to the economic benefits, the greenhouse gases emissions were evaluated, finding that the geothermal energy system implies a reduction of these emissions. This reflects the fact that, in addition to being economically viable, the geothermal energy is considered a clean energy.

Trade-off study on deorbiting S/C in near polar orbit

Usual long, flexible, ED tethers kept vertical by the gravity gradient might be less efficient for deorbiting S/C in near-polar orbits than conventional (Hall, Ion) electrical thrusters. A trade-off study on this application is here presented for tethers kept horizontal and perpendicular to the orbital plane. A tether thus oriented must be rigid and short for structural reasons, requiring a non-convex cross section and a power supply as in the case of electrical thrusters. Very recent developments on bare-tether collection theory allow predicting the current collected by an arbitrary cross section. For the horizontal tether, structural considerations on length play the role of ohmic effects in vertical tethers, in determining the optimal contribution of tether mass to the overall deorbiting system. For a given deorbiting-mission impulse, tether-system mass is minimal at some optimal length that increases weakly with the impulse. The horizontal-tether system may beat both the vertical tether and the electrical thruster as regards mass requirements for a narrow length range centered at about 100 m, allowing, however, for a broad mission-impulse range.

Instituto de Sistemas Fotovoltaicos de Concentración concentration photovoltaics hybrid system first year of operation and improvements

A photovoltaic (PV) hybrid system combines PV with other forms of electricity generation, usually a diesel generator. The system presented in this paper uses concentration photovoltaic (CPV) as the main generator in combination with a storage system and the grid, configured as the backup power supply. The load of the system consists of an air conditioning system of an office building. This paper presents the results obtained from the first months of operation of the CPV hybrid system installed at Instituto de Sistemas Fotovoltaicos de Concentración facilities together with exhaustive simulations in order to model the system behaviour and be able to improve the self-consumption ratio. This system represents a first approach to the use of a CPV in office buildings complemented by an existing AC-coupled hybrid system. The contribution of this paper to the analysis of this new system and the existing tools available for its simulation, at least a part of it, can be considered as a starting point for the development of these kinds of systems.

A voltage disturbances prototype for testing electrical generators connected to microgrids

The search for new energy models arises as a necessity to have a sustainable power supply. The inclusion of distributed generation sources (DG) allows to reduce the cost of facilities, increase the security of the grid or alleviate problems of congestion through the redistribution of power flows. In remote microgrids it is needed in a particular way a safe and reliable supply, which can cover the demand for a low cost; due to this, distributed generation is an alternative that is being widely introduced in these grids. But the remote microgrids are especially weak grids because of their small size, low voltage level, reduced network mesh and distribution lines with a high ratio R/X. This ratio affects the coupling between grid voltages and phase shifts, and stability becomes an issue of greater importance than in interconnected systems. To ensure the appropriate behavior of generation sources inserted in remote microgrids -and, in general, any electrical equipment-, it is essential to have devices for testing and certification. These devices must, not only faithfully reproduce disturbances occurring in remote microgrids, but also to behave against the equipment under test (EUT) as a real weak grid. This also makes the device commercially competitive. To meet these objectives and based on the aforementioned, it has been designed, built and tested a voltage disturbances generator, in order to provide a simple, versatile, full and easily scalable device to manufacturers and laboratories in the sector.

Microinformática en entornos profesionales : instalación, configuración, mantenimiento y reparación

Los sistemas microinformáticos se componen principalmente de hardware y software, con el paso del tiempo el hardware se degrada, se deteriora y en ocasiones se avería. El software evoluciona, requiere un mantenimiento, de actualización y en ocasiones falla teniendo que ser reparado o reinstalado. A nivel hardware se analizan los principales componentes que integran y que son comunes en gran parte estos sistemas, tanto en equipos de sobre mesa como portátiles, independientes del sistema operativo, además de los principales periféricos, también se analizan y recomiendan algunas herramientas necesarias para realizar el montaje, mantenimiento y reparación de estos equipos. Los principales componentes hardware internos son la placa base, memoria RAM, procesador, disco duro, carcasa, fuente de alimentación y tarjeta gráfica. Los periféricos más destacados son el monitor, teclado, ratón, impresora y escáner. Se ha incluido un apartado donde se detallan los distintos tipos de BIOS y los principales parámetros de configuración. Para todos estos componentes, tanto internos como periféricos, se ha realizado un análisis de las características que ofrecen y los detalles en los que se debe prestar especial atención en el momento de seleccionar uno frente a otro. En los casos que existen diferentes tecnologías se ha hecho una comparativa entre ambas, destacando las ventajas y los inconvenientes de unas frente a otras para que sea el usuario final quien decida cual se ajusta mejor a sus necesidades en función de las prestaciones y el coste. Un ejemplo son las impresoras de inyección de tinta frente a las laser o los discos duros mecánicos en comparación con y los discos de estado sólido (SSD). Todos estos componentes están relacionados, interconectados y dependen unos de otros, se ha dedicado un capítulo exclusivamente para estudiar cómo se ensamblan estos componentes, resaltando los principales fallos que se suelen cometer o producir y se han indicado unas serie tareas de mantenimiento preventivo que se pueden realizar para prolongar la vida útil del equipo y evitar averías por mal uso. Los mantenimientos se pueden clasificar como predictivo, perfectivo, adaptativo, preventivo y correctivo. Se ha puesto el foco principalmente en dos tipos de mantenimiento, el preventivo descrito anteriormente y en el correctivo, tanto software como hardware. El mantenimiento correctivo está enfocado al análisis, localización, diagnóstico y reparación de fallos y averías hardware y software. Se describen los principales fallos que se producen en cada componente, cómo se manifiestan o qué síntomas presentan para poder realizar pruebas específicas que diagnostiquen y acoten el fallo. En los casos que es posible la reparación se detallan las instrucciones a seguir, en otro caso se recomienda la sustitución de la pieza o componente. Se ha incluido un apartado dedicado a la virtualización, una tecnología en auge que resulta muy útil para realizar pruebas de software, reduciendo tiempos y costes en las pruebas. Otro aspecto interesante de la virtualización es que se utiliza para montar diferentes servidores virtuales sobre un único servidor físico, lo cual representa un importante ahorro en hardware y costes de mantenimiento, como por ejemplo el consumo eléctrico. A nivel software se realiza un estudio detallado de los principales problemas de seguridad y vulnerabilidades a los que está expuesto un sistema microinformático enumerando y describiendo el comportamiento de los distintos tipos de elementos maliciosos que pueden infectar un equipo, las precauciones que se deben tomar para minimizar los riesgos y las utilidades que se pueden ejecutar para prevenir o limpiar un equipo en caso de infección. Los mantenimientos y asistencias técnicas, en especial las de tipo software, no siempre precisan de la atención presencial de un técnico cualificado, por ello se ha dedicado un capítulo a las herramientas de asistencia remota que se pueden utilizar en este ámbito. Se describen algunas de las más populares y utilizadas en el mercado, su funcionamiento, características y requerimientos. De esta forma el usuario puede ser atendido de una forma rápida, minimizando los tiempos de respuesta y reduciendo los costes. ABSTRACT Microcomputer systems are basically made up of pieces of hardware and software, as time pass, there’s a degradation of the hardware pieces and sometimes failures of them. The software evolves, new versions appears and requires maintenance, upgrades and sometimes also fails having to be repaired or reinstalled. The most important hardware components in a microcomputer system are analyzed in this document for a laptop or a desktop, with independency of the operating system they run. In addition to this, the main peripherals and devices are also analyzed and a recommendation about the most proper tools necessary for maintenance and repair this kind of equipment is given as well. The main internal hardware components are: motherboard, RAM memory, microprocessor, hard drive, housing box, power supply and graphics card. The most important peripherals are: monitor, keyboard, mouse, printer and scanner. A section has been also included where different types of BIOS and main settings are listed with the basic setup parameters in each case. For all these internal components and peripherals, an analysis of their features has been done. Also an indication of the details in which special attention must be payed when choosing more than one at the same time is given. In those cases where different technologies are available, a comparison among them has been done, highlighting the advantages and disadvantages of selecting one or another to guide the end user to decide which one best fits his needs in terms of performance and costs. As an example, the inkjet vs the laser printers technologies has been faced, or also the mechanical hard disks vs the new solid state drives (SSD). All these components are interconnected and are dependent one to each other, a special chapter has been included in order to study how they must be assembled, emphasizing the most often mistakes and faults that can appear during that process, indicating different tasks that can be done as preventive maintenance to enlarge the life of the equipment and to prevent damage because of a wrong use. The different maintenances can be classified as: predictive, perfective, adaptive, preventive and corrective. The main focus is on the preventive maintains, described above, and in the corrective one, in software and hardware. Corrective maintenance is focused on the analysis, localization, diagnosis and repair of hardware and software failures and breakdowns. The most typical failures that can occur are described, also how they can be detected or the specific symptoms of each one in order to apply different technics or specific tests to diagnose and delimit the failure. In those cases where the reparation is possible, instructions to do so are given, otherwise, the replacement of the component is recommended. A complete section about virtualization has also been included. Virtualization is a state of the art technology that is very useful especially for testing software purposes, reducing time and costs during the tests. Another interesting aspect of virtualization is the possibility to have different virtual servers on a single physical server, which represents a significant savings in hardware inversion and maintenance costs, such as electricity consumption. In the software area, a detailed study has been done about security problems and vulnerabilities a microcomputer system is exposed, listing and describing the behavior of different types of malicious elements that can infect a computer, the precautions to be taken to minimize the risks and the tools that can be used to prevent or clean a computer system in case of infection. The software maintenance and technical assistance not always requires the physical presence of a qualified technician to solve the possible problems, that’s why a complete chapter about the remote support tools that can be used to do so has been also included. Some of the most popular ones used in the market are described with their characteristics and requirements. Using this kind of technology, final users can be served quickly, minimizing response times and reducing costs.

Sistema autónomo para carga de baterías mediante una instalación fotovoltaica con aplicación directa al vehículo eléctrico y usos

La situación energética actual es insostenible y como consecuencia se plantea un escenario próximo orientado a conseguir un futuro energético sostenible que permita el desarrollo económico y el bienestar social. La situación ambiental actual está afectada directamente por la combustión de combustibles fósiles que en 2013 constituyeron el 81% de la energía primaria utilizada por el ser humano y son la principal fuente antropogénica de gases de efecto invernadero. Los informes del IPCC1, ponen de manifiesto que el cambio climático se ha consolidado durante los últimos años y en la conferencia de la ONU sobre cambio climático de París que se celebrará a finales de 2015, se pretende que los gobiernos suscriban un acuerdo universal para limitar las emisiones de gases de efecto invernadero y evitar que el incremento de la temperatura media global supere los 2°C. Por otra parte, en el interior de las ciudades es especialmente preocupante, por su efecto directo sobre la salud humana, el impacto ambiental producido por las emisiones de NOx que generan el transporte de personas y mercancías. El sector del transporte fue responsable en 2012 del 27,9% del consumo final de energía. Una vez expuesto el escenario energético y ambiental actual, en esta tesis, se analiza la eficiencia de un sistema autónomo fotovoltaico para la carga de baterías de vehículos eléctricos y el uso del mismo con otras cargas, con el objetivo de aprovechar al máximo la energía eléctrica generada y contribuir a la utilización de energía limpia que no produzca impacto ambiental. Como primer paso para el desarrollo de la tesis se hizo un estudio de trabajos previos comenzando por las primeras aplicaciones de la energía fotovoltaica en los vehículos solares para después pasar a trabajos más recientes enfocados al suministro de energía a los vehículos eléctricos. También se hizo este estudio sobre las metodologías de simulación en los sistemas fotovoltaicos y en el modelado de distintos componentes. Posteriormente se eligieron, dentro de la amplia oferta existente en el mercado, los componentes con características técnicas más adecuadas para este tipo de instalaciones y para las necesidades que se pretenden cubrir. A partir de los parámetros técnicos de los componentes elegidos para configurar la instalación autónoma y utilizando modelos contrastados de distintos componentes, se ha desarrollado un modelo de simulación en ordenador del sistema completo con el que se han hecho simulaciones con distintos modos de demanda de energía eléctrica, según los modos de carga disponibles en el vehículo eléctrico para corriente alterna monofásica de 230 V. También se han simulado distintos tamaños del generador fotovoltaico y del sistema de acumulación de energía eléctrica para poder determinar la influencia de estos parámetros en los balances energéticos del sistema. Utilizando recursos propios el doctorando ha realizado la instalación real de un sistema fotovoltaico que incluye sistema de acumulación e inversor en un edificio de su propiedad. Para la realización de la tesis, La Fundación de Fomento e Innovación Industrial (F2I2) ha facilitado al doctorando un dispositivo que permite realizar la alimentación del vehículo eléctrico en modo 2 (este modo emplea un adaptador que incorpora dispositivos de seguridad y se comunica con el vehículo permitiendo ajustar la velocidad de recarga) y que ha sido necesario para los trabajos desarrollados. Se ha utilizado la red eléctrica como sistema de apoyo de la instalación fotovoltaica para permitir la recarga en el modo 2 que requiere más potencia que la proporcionada por el sistema fotovoltaico instalado. Se han analizado mediante simulación distintos regímenes de carga que se han estudiado experimentalmente en la instalación realizada, a la vez que se han hecho ensayos que se han reproducido mediante simulación con los mismos valores de radiación solar y temperatura con objeto de contrastar el modelo. Se han comparado los resultados experimentales con los obtenidos mediante simulación con objeto de caracterizar el comportamiento del sistema de acumulación (energía eléctrica suministrada y tensión de salida en las baterías) y del generador fotovoltaico (energía eléctrica fotovoltaica suministrada). Por último, se ha realizado un estudio económico de la instalación autónoma fotovoltaica ejecutada y simulada. En el mismo se ha planteado la utilización de fondos propios (como realmente se ha llevado a cabo) y la utilización de financiación, para determinar dos posibles escenarios que pudieran ser de utilidad a un propietario de vehículo eléctrico. Se han comparado los resultados obtenidos en los dos escenarios propuestos del estudio económico del sistema, en cuanto a los parámetros de tiempo de retorno de la inversión, valor actual neto de la inversión y tasa interna de retorno de la misma. Las conclusiones técnicas obtenidas, permiten la utilización del sistema con los modos de carga ensayados y otro tipo de cargas que aprovechen la generación eléctrica del sistema. Las baterías ofrecen mejor comportamiento cuando el aporte fotovoltaico está presente, pero no considera adecuado la conexión de cargas elevadas a un sistema de acumulación de gel (plomo-acido) como el que se ha utilizado, debido al comportamiento de este tipo de baterías ante demandas de intensidad de corriente eléctrica elevadas. Por otra parte, el comportamiento de este tipo de baterías con valores de intensidad de corriente eléctrica inferiores a 10 A en ausencia de energía fotovoltaica, con el objetivo de utilizar la generación de energía eléctrica diaria acumulada en el sistema, sí resulta interesante y ofrece un buen comportamiento del sistema de acumulación. Las circunstancias actuales de mercado, que carece de sistemas de acumulación de litio con precios de compra interesantes, no han permitido poder experimentar este sistema de acumulación en la instalación autónoma fotovoltaica ejecutada, tampoco se ha podido obtener el favor de ningún fabricante para ello. Actualmente hay disponibles sistemas de acumulación en litio que no se comercializan en España y que serían adecuados para el sistema de acumulación de energía propuesto en este estudio, que deja abierta las puertas para futuros trabajos de investigación. Las conclusiones económicas obtenidas, rentabilizan el uso de una instalación autónoma fotovoltaica con consumo instantáneo, sin acumulación de energía eléctrica. El futuro de conexión a red por parte de estas instalaciones, cuando se regule, aportará un incentivo económico para rentabilizar con menos tiempo las instalaciones autónomas fotovoltaicas, esto también deja la puerta abierta a futuros trabajos de investigación. El sistema de acumulación de energía aporta el mayor peso económico de inversión en este tipo de instalaciones. La instalación estudiada aporta indicadores económicos que la hacen rentable, pero se necesitaría que los precios de acumulación de la energía en sistemas eficientes estén comprendidos entre 100-200 €/kWh para que el sistema propuesto en este trabajo resulte atractivo a un potencial propietario de un vehículo eléctrico. ABSTRACT The current energy situation is untenable; it poses a scenario next focused on reaching a sustainable energy future, to allow economic development and social welfare. The environmental current situation is affected directly by the combustion of fossil fuels that in 2013 constituted 81 % of the primary energy used by the human being and they are the principal source human of greenhouse gases. The reports of the IPCC2, they reveal that the climate change has consolidated during the last years and in the conference of the UNO on climate change of Paris that will be celebrated at the end of 2015, there is claimed that the governments sign a universal agreement to limit the emission of greenhouse gases and to prevent that the increase of the global average temperature overcomes them 2°C. On the other hand, inside the cities it is specially worrying, for his direct effect on the human health, the environmental impact produced by the NOx emissions that generate the persons' transport and goods. The sector of the transport was responsible in 2012 of 27,9 % of the final consumption of energy. Once exposed the scenario and present environmental energy, in this thesis, it has analyzed the efficiency of an autonomous photovoltaic system for charging electric vehicles, and the use of the same with other workloads, with the objective to maximize the electrical energy generated and contribute to the use of clean energy that does not produce environmental impact. Since the first step for the development of the thesis did to itself a study of previous works beginning for the first applications of the photovoltaic power in the solar vehicles later to go on to more recent works focused on the power supply to the electrical vehicles. Also this study was done on the methodologies of simulation in the photovoltaic systems and in the shaped one of different components. Later they were chosen, inside the wide existing offer on the market, the components with technical characteristics more adapted for this type of facilities and for the needs that try to cover. From the technical parameters of the components chosen to form the autonomous installation and using models confirmed of different components, a model of simulation has developed in computer of the complete system with which simulations have been done by different manners of demand of electric power, according to the available manners of load in the electrical vehicle for single-phase alternating current of 230 V. Also there have been simulated different sizes of the photovoltaic generator and of the system of accumulation of electric power to be able to determine the influence of these parameters in the energy balances of the system. Using own resources the PhD student has realized a real installation of a photovoltaic system that includes system of accumulation and investing in a building of his property. For the accomplishment of the thesis, The Foundation of Promotion and Industrial Innovation (F2I2) it has facilitated to the PhD student a device that allows to realize the supply of the electrical vehicle in way 2 (this way uses an adapter that incorporates safety devices and communicates with the vehicle allowing to fit the speed of recharges) and that has been necessary for the developed works. The electrical network has been in use as system of support of the photovoltaic installation for allowing it her recharges in the way 2 that more power needs that provided by the photovoltaic installed system. There have been analyzed by means of simulation different rate of load that have been studied experimentally in the realized installation, simultaneously that have done to themselves tests that have reproduced by means of simulation with the same values of solar radiation and temperature in order the model contrasted. The experimental results have been compared by the obtained ones by means of simulation in order to characterize the behavior of the system of accumulation (supplied electric power and tension of exit in the batteries) and of the photovoltaic generator (photovoltaic supplied electric power). Finally, there has been realized an economic study of the autonomous photovoltaic executed and simulated installation. In the same one there has appeared the utilization of own funds (since really it has been carried out) and the utilization of financing, to determine two possible scenes that could be of usefulness to an owner of electrical vehicle. There have been compared the results obtained in both scenes proposed of the economic study of the system, as for the parameters of time of return of the investment, current clear value of the investment and rate hospitalizes of return of the same one. The technical obtained conclusions, they make the utilization of the system viable with the manners of load tested and another type of loads of that they take advantage the electrical generation of the system. The batteries offer better behavior when the photovoltaic contribution is present, but he does not consider to be suitable the connection of loads risen up to a system of accumulation of gel (lead - acid) as the one that has been in use, due to the behavior of this type of batteries before demands of intensity of electrical current raised. On the other hand, the behavior of this type of batteries with low values of intensity of electrical current to 10 To in absence of photovoltaic power, with the aim to use the generation of daily electric power accumulated in the system, yes turns out to be interesting and offers a good behavior of the system of accumulation. The current circumstances of market, which lacks systems of accumulation of lithium with interesting purchase prices, have not allowed to be able to experience this system of accumulation in the autonomous photovoltaic executed installation, neither one could have obtained the favor of any manufacturer for it. Nowadays there are available systems of accumulation in lithium that is not commercialized in Spain and that they would be adapted for the system of accumulation of energy proposed in this study, which makes the doors opened for future works of investigation. The economic obtained conclusions; they make more profitable the use of an autonomous photovoltaic installation with instantaneous consumption, without accumulation of electric power. The future of connection to network on the part of these facilities, when it is regulated, will contribute an economic incentive to make profitable with less time the autonomous photovoltaic facilities, this also leaves the door opened for future works of investigation. The system of accumulation of energy contributes the major economic weight of investment in this type of facilities. The studied installation contributes economic indicators that make her profitable, but it would be necessary that the prices of accumulation of the energy in efficient systems are understood between 100-200 € in order that the system proposed in this work turns out to be attractive to a proprietary potential of an electrical vehicle.

Aplicación de la metodología ISA al análisis de la secuencia de pérdida del sistema de agua de refrigeración de componentes en una central nuclear con reactor de agua a presión

La metodología Integrated Safety Analysis (ISA), desarrollada en el área de Modelación y Simulación (MOSI) del Consejo de Seguridad Nuclear (CSN), es un método de Análisis Integrado de Seguridad que está siendo evaluado y analizado mediante diversas aplicaciones impulsadas por el CSN; el análisis integrado de seguridad, combina las técnicas evolucionadas de los análisis de seguridad al uso: deterministas y probabilistas. Se considera adecuado para sustentar la Regulación Informada por el Riesgo (RIR), actual enfoque dado a la seguridad nuclear y que está siendo desarrollado y aplicado en todo el mundo. En este contexto se enmarcan, los proyectos Safety Margin Action Plan (SMAP) y Safety Margin Assessment Application (SM2A), impulsados por el Comité para la Seguridad de las Instalaciones Nucleares (CSNI) de la Agencia de la Energía Nuclear (NEA) de la Organización para la Cooperación y el Desarrollo Económicos (OCDE) en el desarrollo del enfoque adecuado para el uso de las metodologías integradas en la evaluación del cambio en los márgenes de seguridad debidos a cambios en las condiciones de las centrales nucleares. El comité constituye un foro para el intercambio de información técnica y de colaboración entre las organizaciones miembro, que aportan sus propias ideas en investigación, desarrollo e ingeniería. La propuesta del CSN es la aplicación de la metodología ISA, especialmente adecuada para el análisis según el enfoque desarrollado en el proyecto SMAP que pretende obtener los valores best-estimate con incertidumbre de las variables de seguridad que son comparadas con los límites de seguridad, para obtener la frecuencia con la que éstos límites son superados. La ventaja que ofrece la ISA es que permite el análisis selectivo y discreto de los rangos de los parámetros inciertos que tienen mayor influencia en la superación de los límites de seguridad, o frecuencia de excedencia del límite, permitiendo así evaluar los cambios producidos por variaciones en el diseño u operación de la central que serían imperceptibles o complicados de cuantificar con otro tipo de metodologías. La ISA se engloba dentro de las metodologías de APS dinámico discreto que utilizan la generación de árboles de sucesos dinámicos (DET) y se basa en la Theory of Stimulated Dynamics (TSD), teoría de fiabilidad dinámica simplificada que permite la cuantificación del riesgo de cada una de las secuencias. Con la ISA se modelan y simulan todas las interacciones relevantes en una central: diseño, condiciones de operación, mantenimiento, actuaciones de los operadores, eventos estocásticos, etc. Por ello requiere la integración de códigos de: simulación termohidráulica y procedimientos de operación; delineación de árboles de sucesos; cuantificación de árboles de fallos y sucesos; tratamiento de incertidumbres e integración del riesgo. La tesis contiene la aplicación de la metodología ISA al análisis integrado del suceso iniciador de la pérdida del sistema de refrigeración de componentes (CCWS) que genera secuencias de pérdida de refrigerante del reactor a través de los sellos de las bombas principales del circuito de refrigerante del reactor (SLOCA). Se utiliza para probar el cambio en los márgenes, con respecto al límite de la máxima temperatura de pico de vaina (1477 K), que sería posible en virtud de un potencial aumento de potencia del 10 % en el reactor de agua a presión de la C.N. Zion. El trabajo realizado para la consecución de la tesis, fruto de la colaboración de la Escuela Técnica Superior de Ingenieros de Minas y Energía y la empresa de soluciones tecnológicas Ekergy Software S.L. (NFQ Solutions) con el área MOSI del CSN, ha sido la base para la contribución del CSN en el ejercicio SM2A. Este ejercicio ha sido utilizado como evaluación del desarrollo de algunas de las ideas, sugerencias, y los algoritmos detrás de la metodología ISA. Como resultado se ha obtenido un ligero aumento de la frecuencia de excedencia del daño (DEF) provocado por el aumento de potencia. Este resultado demuestra la viabilidad de la metodología ISA para obtener medidas de las variaciones en los márgenes de seguridad que han sido provocadas por modificaciones en la planta. También se ha mostrado que es especialmente adecuada en escenarios donde los eventos estocásticos o las actuaciones de recuperación o mitigación de los operadores pueden tener un papel relevante en el riesgo. Los resultados obtenidos no tienen validez más allá de la de mostrar la viabilidad de la metodología ISA. La central nuclear en la que se aplica el estudio está clausurada y la información relativa a sus análisis de seguridad es deficiente, por lo que han sido necesarias asunciones sin comprobación o aproximaciones basadas en estudios genéricos o de otras plantas. Se han establecido tres fases en el proceso de análisis: primero, obtención del árbol de sucesos dinámico de referencia; segundo, análisis de incertidumbres y obtención de los dominios de daño; y tercero, cuantificación del riesgo. Se han mostrado diversas aplicaciones de la metodología y ventajas que presenta frente al APS clásico. También se ha contribuido al desarrollo del prototipo de herramienta para la aplicación de la metodología ISA (SCAIS). ABSTRACT The Integrated Safety Analysis methodology (ISA), developed by the Consejo de Seguridad Nuclear (CSN), is being assessed in various applications encouraged by CSN. An Integrated Safety Analysis merges the evolved techniques of the usually applied safety analysis methodologies; deterministic and probabilistic. It is considered as a suitable tool for assessing risk in a Risk Informed Regulation framework, the approach under development that is being adopted on Nuclear Safety around the world. In this policy framework, the projects Safety Margin Action Plan (SMAP) and Safety Margin Assessment Application (SM2A), set up by the Committee on the Safety of Nuclear Installations (CSNI) of the Nuclear Energy Agency within the Organization for Economic Co-operation and Development (OECD), were aimed to obtain a methodology and its application for the integration of risk and safety margins in the assessment of the changes to the overall safety as a result of changes in the nuclear plant condition. The committee provides a forum for the exchange of technical information and cooperation among member organizations which contribute their respective approaches in research, development and engineering. The ISA methodology, proposed by CSN, specially fits with the SMAP approach that aims at obtaining Best Estimate Plus Uncertainty values of the safety variables to be compared with the safety limits. This makes it possible to obtain the exceedance frequencies of the safety limit. The ISA has the advantage over other methods of allowing the specific and discrete evaluation of the most influential uncertain parameters in the limit exceedance frequency. In this way the changes due to design or operation variation, imperceptibles or complicated to by quantified by other methods, are correctly evaluated. The ISA methodology is one of the discrete methodologies of the Dynamic PSA framework that uses the generation of dynamic event trees (DET). It is based on the Theory of Stimulated Dynamics (TSD), a simplified version of the theory of Probabilistic Dynamics that allows the risk quantification. The ISA models and simulates all the important interactions in a Nuclear Power Plant; design, operating conditions, maintenance, human actuations, stochastic events, etc. In order to that, it requires the integration of codes to obtain: Thermohydraulic and human actuations; Even trees delineation; Fault Trees and Event Trees quantification; Uncertainty analysis and risk assessment. This written dissertation narrates the application of the ISA methodology to the initiating event of the Loss of the Component Cooling System (CCWS) generating sequences of loss of reactor coolant through the seals of the reactor coolant pump (SLOCA). It is used to test the change in margins with respect to the maximum clad temperature limit (1477 K) that would be possible under a potential 10 % power up-rate effected in the pressurized water reactor of Zion NPP. The work done to achieve the thesis, fruit of the collaborative agreement of the School of Mining and Energy Engineering and the company of technological solutions Ekergy Software S.L. (NFQ Solutions) with de specialized modeling and simulation branch of the CSN, has been the basis for the contribution of the CSN in the exercise SM2A. This exercise has been used as an assessment of the development of some of the ideas, suggestions, and algorithms behind the ISA methodology. It has been obtained a slight increase in the Damage Exceedance Frequency (DEF) caused by the power up-rate. This result shows that ISA methodology allows quantifying the safety margin change when design modifications are performed in a NPP and is specially suitable for scenarios where stochastic events or human responses have an important role to prevent or mitigate the accidental consequences and the total risk. The results do not have any validity out of showing the viability of the methodology ISA. Zion NPP was retired and information of its safety analysis is scarce, so assumptions without verification or approximations based on generic studies have been required. Three phases are established in the analysis process: first, obtaining the reference dynamic event tree; second, uncertainty analysis and obtaining the damage domains; third, risk quantification. There have been shown various applications of the methodology and advantages over the classical PSA. It has also contributed to the development of the prototype tool for the implementation of the ISA methodology (SCAIS).

Modelagem e análise das cadeias de suprimentos globais e resilientes baseadas em rede de Petri.

Em um cenário de aumento de competitividade, crescente expectativa por inovações do produto e necessidade de atender diferentes perfis de consumidores, o conceito de gerenciamento de cadeias de suprimentos globais (GSCM) surge como uma estratégia para coordenar mais eficazmente as atividades dispersas geograficamente dos sistemas produtivos. Na adoção do GSCM, as organizações devem lidar com rupturas que impactam no gerenciamento das suas atividades, tais como a interrupção de vias de transporte, pane no fornecimento de energia, desastres naturais e até ataques terroristas. Nesse contexto, o trabalho introduz um procedimento sistematizado para modelagem das cadeias de suprimentos visto como um sistema a eventos discretos e sua análise por simulação das atividades do GSCM baseada em técnicas formais como a rede de Petri (PN) e o Production Flow Schema (PFS). Um exemplo é também apresentado para ilustrar e comprovar as vantagens do método proposto na análise do GSCM.

Compliance problems of small utility systems with the Powerplant and Industrial Fuel Use Act of 1978.

"DOE/RG-0045."

Manual of standard and recommended practices.

Section 16 not yet published.

Small-scale hydropower development in Illinois : an implementation manual /

"Project no. 80.190."

Wireless telemedicine for the delivery of specialist paediatric services to the bedside

A mobile interactive online health system was used to conduct virtual ward rounds at a regional hospital which had no specialist paediatrician. The system was wireless, which allowed telepaediatric services to be delivered direct to the bedside. Between December 2004 and May 2005, 43 virtual ward rounds were coordinated between specialists based in Brisbane and local staff at the Gladstone Hospital. Eighty-six consultations were provided for 64 patients. The most common conditions included asthma (27%), chest infections (12%), gastroenteritis (10%) and urinary tract infections (10%). In the majority of cases, there were partial (67%) or complete changes (11%) in the clinical management of patients. Specialist services were offered by a team of 13 clinicians at the Royal Children's Hospital: 10 general paediatricians, two physiotherapists and one registered nurse. Feedback from all consultants involved in the service and local staff in Gladstone was extremely positive. In 43 videoconference calls there were three technical problems, probably due to an intermittent mains power supply at the regional hospital. There appears to be potential for other rural and regional hospitals to adopt this model of service delivery.