1000 resultados para perdas de água e solo


Relevância:

90.00% 90.00%

Publicador:

Resumo:

The largest losses in mechanical harvesting of peanuts occur during the stage of digging, and its assessment is still incipient in Brazil. Therefore, the aim of this study was to evaluate the quantitative losses and the performance of the tractor-digger-inverter, according to soil water content and plant populations. The experiment was conducted in a completely randomized block design with a factorial scheme 2 x 3, in which the treatments consisted of two soil, water content (19.3 and 24.8%) and three populations of plants (86,111, 127,603 and 141,144 plants ha-1), with four replications. The quantitative digging losses and the set mechanized performance were evaluated. The largest amount of visible and total losses was found in the population of 141.144 plants ha-1 for the 19.3% soil water content. The harvested material flow and the tractor-digger-inverter performance were not influenced by soil water content and plant population. The water content in the pods was higher in 24.8% soil water content only for the population of 86,111 plants ha-1; the yield was higher in the populations of 141.144 and 127.603 plants ha-1, in the 19.3 e 24.8% soil water content, respectively.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Pós-graduação em Agronomia (Produção Vegetal) - FCAV

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Soil compaction is one of the limiting factors in areas subjected to direct seeding. The method used to break up the compacted layer should disturb the soil as little as possible, as well as maintain the ground cover. The aim of this study was to evaluate the influence of subsoiling, scarification and use of shaft-type furrowing mechanisms when sowing, on preserving the ground cover, water content and soil density, as well as the effects on maize yield in a dystroferic Red Nitosol, cultivated under a system of direct seeding for ten years. The experimental design was of randomised blocks, with eight soil management treatments: subsoiling to a depth of 0.40 m before sowing the winter crop, subsoiling to 0.40 m before sowing the maize, scarification to 0.30 m before the winter crop, scarification to 0.30 m before the maize, scarification to 0.20 m before the winter crop, scarification to 0.20 m before the maize, direct seeding of the maize with a shaft-type furrowing mechanism and direct seeding of the maize using a double disc furrower. There were four replications. Subsoiling and scarification influenced the preservation of the ground cover, soil density and water content immediately after sowing, but did not interfere in plant development or grain yield in the maize crop. The use of shaft-type furrowing mechanisms in the sowing operation had no effect on any of the parameters under study.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Devido à constante preocupação do meio ambiente, o uso de fluidos de corte tem se tornado um problema para a indústria mecânica atual por se tratar de substâncias tóxicas. Seu uso e sua dificuldade de descarte devido rígida Legislação Ambiental, faz com que o fluido de corte seja responsável por uma grande parte do custo final do processo, provocando, desse modo, um grande interesse em pesquisas referentes a métodos alternativos de forma e quantidade de fluido de corte utilizado. Ao lado das vantagens tecnológicas associadas com o uso dos fluidos de corte estão os enormes perigos atrelados a estes, e que são nocivos ao meio ambiente e à saúde das pessoas. A contaminação do solo, água e ar podem decorrer de vazamentos e perdas, emissões, água de lavagem e da própria disposição dos fluidos de corte.Os componentes dos fluidos de corte como bactericidas e fungicidas reagem com outros produtos inseridos no processo de corte, tornando os fluidos, materiais que podem vir a causar doenças. Assim, este trabalho tem como objetivo apresentar a utilização do fluido de corte por mínima quantidade de lubrificação como alternativa para se minimizar o impacto ambiental das indústrias mecânicas.